Scribd
Upload
599 views

Basecrete Specification Guide

BaseCrete is a waterproofing bond coat and micro topping that can be used for waterproofing applications like pool decks, water reservoirs, and marine structures. It adheres strongly to most surfaces, is resistant to chemicals, and can withstand movement. BaseCrete is available in liquid and powder form and is applied in two thin coats using tools like trowels, rollers, or sprayers. It requires substrate preparation and curing time depending on temperature before use. BaseCrete has high strength, adhesion, and withstands impacts, chemicals, and freeze-thaw cycles according to industry standards.

Uploaded by

Guntur S Pambudi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
599 views

Basecrete Specification Guide

BaseCrete is a waterproofing bond coat and micro topping that can be used for waterproofing applications like pool decks, water reservoirs, and marine structures. It adheres strongly to most surfaces, is resistant to chemicals, and can withstand movement. BaseCrete is available in liquid and powder form and is applied in two thin coats using tools like trowels, rollers, or sprayers. It requires substrate preparation and curing time depending on temperature before use. BaseCrete has high strength, adhesion, and withstands impacts, chemicals, and freeze-thaw cycles according to industry standards.

Uploaded by

Guntur S Pambudi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

BASECRETE

CONCRETE WATERPROOFING BOND COAT

PRODUCT SPECIFICATION
1.1 DESCRIPTION
BASECRETE IS A WATERPROOFING BONDCOAT / UNDERLAYMENT / MICRO TOPPING
FOR USE IN ALL APPLICATIONS WHERE A SOLID AND DURABLE WATERPROOF
BARRIER IS REQUIRED. BASECRETE WILL ADHERE TO MOST SURFACES, IS
RESISTANT TO MOST CHEMICALS AND CORROSIVE AGENTS AND CAN WITHSTAND A
HIGH DEGREE OF MOVEMENT WHILE MAINTAINING ITS INTEGRITY. BASECRETE IS A
LIQUID AND COMPOUND MIX DESIGN AVAILABLE IN 1 & 5 GALLON PAILS AND 50LB
BAGS. BASECRETE IS JOB SITE READY.
2.1 WATERPROOFING APPLICATIONS
WATERPROOF BONDCOAT POOL DECKS CISTERNS & WATER RESERVOIRS SUSPENDED POOLS
UNDERLAYMENT PLANTERS CATWALKS & WALKWAYS COMMERCIAL POOLS
MICRO TOPPING SCRATCH COAT BREAK WALLS RESIDENTIAL POOLS
STUCCO CRACK REPAIRS PARKING GARAGES WATER FEATURES
BARN FOUNDATIONS FISH PONDS AQUATIC ENCLOSURES SUSPENDED DECKS
ANIMAL ENCLOSURES MAN HOLES WILDLIFE WATERING PONDS BYLANDS, DOCKS, PIERS
NATURAL RESERVOIRS ICF & EIF ZOO ENCLOSURES TUCK POINTING
PARGING MAN MADE REEFS MOORINGS/JETTY’S ELEVATOR FOUNDATIONS

2.2 APPLICATION METHODS


A. Tools
BaseCrete can be applied by Trowel, Roller (1” nap), Brush, Squeegee or Spray
B. Thickness
Apply BaseCrete in two (2) layers, one vertically, one horizontally. Each layer should be 1/16” thick
for a total of 1/8” thickness to achieve a waterproof bond coat. The second layer can be applied
once the first layer is dry to the touch.
C. Special Applications
BaseCrete can be built up in 2” increments and feather edged.
2.3 COVERAGE
Coverage is approximate for one coat. Slump can be adjusted to accommodate specific job
requirements by adjusting the liquid or the compound – do not add water to the mix.
A. Trowel…1 gallon & 1 x 50lb bag = 40–50 sq ft @ 1/8”
B. Roller… 5 gallons & 3 x 50lb bags = 450-500 sq ft @ 1/16”
C. Squeegee… 5 gallons & 3 x 50lb bags = 450-500 sq ft @1/16”
D. Spray… 5 gallons & 3 x 50lb bags = 400-500 sq ft @ 1/16”
2.4 SUBSTRATE PREPARATION
A. Initial inspection
Inspect job site. Determine if any pervious material used is incompatible with BaseCrete.
[email protected]

B. Preparing Site
Remove all previous material and any loose debris. Check and repair any cracks or voids with
BaseCrete repair mortar. Once the site is clean and clear of any old material, loose debris, cracks
etc., pressure wash for final preparation. Protect adjacent areas to prevent material from going
beyond designated site.
C. Substrate surface preparation
Begin with a SSD (Saturated Surface Dry) substrate that is clearly damp below the immediate
surface, has no standing water and has a surface that is showing no signs of a “film” of water on
the surface. Ideally the concrete will be clearly damp (typically much darker than dry concrete) but
the surface will have no water present and will be showing “signs” of drying.

Page 1 of 2
BASECRETE
CONCRETE WATERPROOFING BOND COAT

2.5 TEMPERATURE & WEATHER FACTORS


A. Product limitations
Do not allow BaseCrete to freeze or overheat
B. Site temperature
Do not apply BaseCrete to frozen substrate or in conditions hotter than 105 degrees or colder than
40 degrees
Check local weather for temperature variations, precipitation etc that will affect your application.

2.6 MIXING INSTRUCTIONS


Mix on site using 5 gallon pails and paddle mixer. Blend product according to manufacturer’s instructions
on product label. Keep product out of direct sun. Allow product to false set (approximately 5 minutes) and
re mix. Pot life is approximately 30 minutes depending on the temperature and humidity. Use mix ratio
depending on application method.
A. Special Note
Use BaseCrete liquid to change consistency of mix.
Do not add water to the mix.
B. Clean up after mixing
Clean all tools and spills immediately with clean water.

2.7 COLD JONTS and CRACKS


Use BaseCrete Mesh to build rounded coves in corners on all cold joints. Build up with BaseCrete mix.
Use BaseCrete Mesh to fill in and bridge cracks.

3.1 HANDLING AND STORAGE


Keep BaseCrete products off the ground. Keep dry and out of direct sun/heat/cold.

4.1 CUSTOMER SERVICE


We recommend a BaseCrete Representative attend initial applications.

5.1 STANDARDS
A. IMPACT STRENGTH 19 lbs / 8.6 kg
B. COMPRESSIVE STRENGTH 7050 psi / 48.61 MPa
C. TENSILE STRENGTH 732 psi / 5.05 MPa
D. FLEXURAL STRENGTH 2380 psi / 16.41 MPa
E. ADHESIVE STRENGTH
Concrete : 1372 psi / 9.46 MPa
Steel : 1144 psi / 7.89 MPa
[email protected]

F. SHEAR BOND ADHESION 720 psi / 4.96 MPa


G. ASTM E96 – Vapor transmission
H. ASTM C321 – Bond Strength
I. ASTM C672 – Freeze-Thaw
J. ASTM d4541.02 – Pull Off Test

[email protected]

Page 2 of 2

You might also like