Fosroc Conplast SP432MS constructive solutions

High performance superplasticising admixture

Uses Dosage Guideline

 To provide increased ultimate strength gain by signifi- The optimum dosage of Conplast SP432MS to meet specific
cantly reducing water demand in a concrete mix requirements should always be determined by trial mixes
using the materials and conditions that will be experienced
 To significantly improve the workability and retention of
in use.
site mixed concrete without increasing water demand.
For Normal concrete, dosage range is between 0.2 to 2% by
 To provide improved durability by increasing ultimate
weight of cement or cementitious materials including PFA,
strengths and reducing concrete permeability.
GGBFS and microsilica. Dosage can be used up to 2.5% by
 Specifically developed for use in high quality concrete
weight of cement for high performance concrete.
mixes utilising cement replacements.
Use at other dosages
Advantages Dosages outside the above dosage guidelines can be used
 Makes possible major reductions in water:cement ratio to meet particular concrete mix requirements. Please con-
which allows the production of high strength concrete tact Fosroc for advice in such cases.
without excessive cement contents.
Effects of overdosing
 Increased workability levels are maintained for longer
An overdose of double the amount of Conplast SP432MS
than with ordinary sulphonated melamine and naptha-
will result in an increase in retardation as compared to
lene admixtures.
that normally obtained. Provided that adequate curing is
 Improved cohesion and particle dispersion minimises maintained, the ultimate strength of the concrete will not be
segregation and bleeding and improves pumpability. impaired by increased retardation and will generally be in-
creased. The effects of overdosing will be further increased
 Chloride free, safe for use in prestressed and reinforced
if sulphate resisting cement or cement replacement materi-
concrete.
als are used.
Standards compliance
Typical Properties
Conplast SP432MS conforms with BS 5075, BS:EN 934-
2 and with ASTM C494 as Type G depending on dosage Appearance : Brown liquid
used. Specific gravity : 1.19 @ 25°C
Chloride content : Nil to BS 5075 / BS:EN934
Description
Instructions for use
Conplast SP432MS is a chloride free, superplasticising
Mix design
admixture based on selected sulphonated napthalene
polymers. It is supplied as a brown solution which instantly Where the main requirement is to improve strengths, initial
disperses in water. trials should be made with normal concrete mix designs.
The addition of the admixture will allow the removal of water
Conplast SP432MS disperses the fine particles in the
from the mix whilst maintaining workability. After initial trials,
concrete mix, enabling the water content of the concrete
minor modifications to the overall mix design may be made
to perform more effectively. The very high levels of water
to optimise performance.
reduction possible allow major increases in strength to be
obtained. Where the main requirement is to provide high workability
concrete, the mix design should be one suitable for use as
Technical support a pump mix. Advice on mix design for flowing concrete is
available from Fosroc.
Fosroc provides a technical advisory service for on-site as-
Conplast SP432MS

sistance and advice on admixture selection, evaluation trials

and dispensing equipment. Technical data and guidance can
be provided for admixtures and other products for use with
fresh and hardened concrete.
Fosroc Conplast SP432MS

Compatibility Precautions

Conplast SP432MS is compatible with other Fosroc ad- Health and safety
mixtures used in the same concrete mix. All admixtures
Conplast SP432MS does not fall into the hazard classifica-
should be added to the concrete separately and must not be
tions of current regulations. However, it should not be swal-
premixed together prior to addition. The resultant properties
of concrete containing more than one admixture should be lowed or allowed to come into contact with skin and eyes.
assessed by trial mixes. Suitable protective gloves and goggles should be worn.
Conplast SP432MS is suitable for use with all types of Splashes on the skin should be removed with water. In case
Portland cements, SRC cements and cement replacement of contact with eyes rinse immediately with plenty of water
materials such as PFA, GGBFS and microsilica. The use of and seek medical advice. If swallowed seek medical atten-
a combination of admixtures in the same concrete mix and
tion immediately - do not induce vomiting.
or cement replacements may alter the setting time. Trials
should always be conducted to determine such setting times. For further information consult the Material Safety Data
Sheet available for this product.
Dispensing
Fire
The correct quantity of Conplast SP432MS should be meas-
ured by means of a recommended dispenser. Normally, the Conplast SP432MS is water based and non-flammable.
admixture should then be added to the concrete with the
Cleaning and disposal
mixing water to obtain the best results. Where high worka-
bility concrete is required from normal workability concrete Spillages of Conplast SP432MS should be absorbed onto
delivered to site, Conplast SP432MS may also be added to sand, earth or vermiculite and transferred to suitable con-
concrete direct into a readymix truck. Full blending of the tainers. Remnants should be hosed down with large quanti-
admixture and the concrete should be ensured by mixing at ties of water.
high speed for a period of at least two minutes.
The disposal of excess or waste material should be carried
Contact Fosroc for advice regarding suitable equipment and
out in accordance with local legislation under the guidance
its installation.
of the local waste regulatory authority.

Estimating
Additional information
Supply
Conplast SP432MS is a retarded version of Conplast
Conplast SP432MS
SP430*†
210 litre drum, 1000 litre totes or bulk

For larger users, storage tanks can be supplied.

Storage

Conplast SP432MS has a minimum shelf life of 12 months

provided the temperature is kept within the range of 2°C to
50°C. Should the temperature of the product fall outside this * Denotes the trademark of Fosroc International Limited
range contact Fosroc for advice. †
See separate data sheet
Freezing point: Approximately -2°C
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
www.fosroc.com Qatar, Tadmur telephone: 4665501 fax: 4664147 email: [email protected]

UAE/0275/15/G