Fosroc Conplast WP400 constructive solutions

Hydrophobic pore-blocking waterproofing admixture Effects of overdosing

An overdose of Conplast WP400 may result in increased

Uses retardation and workability, hence reduce the short term
strength development. Long term strength is unlikely to be
Conplast WP400 will drastically reduce water absorption
affected.
in structural and precast concrete. It is suitable for use in
below ground structures, reinforced concrete in marine are- Use at other dosages
as, piles, water retaining structures, manholes, waste water
Dosages outside the above dosage guidelines can be used
treatment and desalination plants.
to meet particular concrete mix requirements. Please contact
Fosroc for advice in such cases.
Advantages

 Bitumen ammonia free system Typical Properties

 Provides integral protection, ensuring reduced permea- Appearance : Turbid solution

bility throughout the concrete Specific gravity : 1.03 at 25°C
Chloride content : Nil to BS 5075 / BS:EN934
 Integral protection is maintained even if surface damage
occurs, unlike applied surface films or coatings
Instructions for use
 Lower water:cement ratio improves compressive
Compatibility
strength at same workability
Conplast WP400 is compatible with Conplast SP432MS*†
 Fully compatible with certain Fosroc surface coatings
when used in the same concrete mix, but should be added
and finishes
to the mix separately and must not be mixed together prior
to addition. The resultant properties of mixes containing
Description
more than one admixture should be assessed by the trial
Conplast WP400 chloride free admixture is supplied as a mix procedure recommended on this data sheet.
turbid liquid which instantly disperses in water.
Conplast WP400 is suitable for use with all types of Portland
Conplast WP400 is an organic liquid which reacts with cements, SRC cements and cement replacement materials
products of the cement hydration process to produce a such as PFA, GGBFS and microsilica.
hydrophobic material which repels external water, reducing
The use of a combination of admixtures in the same con-
absorption into the concrete.
crete mix and or cement replacements may alter the setting
time. Trials should always be conducted to determine such
Technical support
setting times.
Fosroc provides a technical advisory service for on-site
Dispensing
assistance and advice on admixture selection, evaluation tri-
als and dispensing equipment. Technical data and guidance The correct quantity of Conplast WP400 should be meas-
can be provided for admixtures and other products for use ured by means of a recommended dispenser. The admixture
with fresh and hardened concrete. should then be added to the concrete with the mixing water
to obtain the best results. Contact the Fosroc Technical
Dosage Guidelines
Department for advice regarding suitable equipment and its
The optimum dosage of Conplast WP400 to meet specific installation.
requirements should always be determined by trials using
Curing
the materials and conditions that will be experienced in use.
This allows the optimisation of admixture dosage and mix As with all structural concrete, good curing practice should
design and provides a complete assessment of the mix. The be maintained, particularly in situations where an overdose
normal recommended dosage is 1.5 to 2.0 litres per 100 kg has occurred. Water spray, wet hessian or a Concure*† spray
of cement. applied curing membrane should be used.
Conplast WP400
Fosroc Conplast WP400

Typical performance example Estimating

Conplast WP400 meets the water absorption requirements of Supply

the European Standard BSEN934-2. Conplast WP400
210 litre drum, 1000 litre totes.
Many variables in concreting materials and conditions can af-
fect the selection and use of an admixture. Trials should be For larger users, storage tanks can be supplied.
carried out using relevant materials and conditions in order to
determine the optimum mix design and admixture dosage to Storage
meet specific requirements. A typical performance exam-
Conplast WP400 has a minimum shelf life of 12 months if
ple from evaluation studies of Conplast WP400 is included
the temperature is kept within the range of 10°C to 50°C.
on this data sheet. The values quoted are representative
Should the temperature of the product fall outside this range
of results obtained and are provided as illustrations of the
contact Fosroc office for advice.
performance.

Because of the variability of concreting materials, the results Precautions

should only be taken as typical of the performance to be ex-
Health and safety
pected. Results quoted are not necessarily directly compara-
ble with results obtained elsewhere for Conplast Conplast WP400 is alkaline and should not be swallowed or
WP400 or other products. allowed to come into contact with skin and eyes.

Example: Concrete grade 45/20, 400 kg cement, 0.38 free w/c. Wear suitable protective gloves and goggles. In case of con-
tact with the skin, wash immediately with soap and water. In
Mix Dosage Absorption case of contact with eyes rinse immediately with plenty of
WP400 SP432MS water and seek medical advice. If swallowed seek medical
% % attention immediately - do not induce vomiting. For further
% information consult the Safety Data Sheet available for this
Control nil 1 2.8 product.
With Conplast 1 1 1.2
Fire
WP400 2 1 0.6
Conplast WP400 is water based and non-flammable.
Limitations
Cleaning and disposal
The use of Conplast WP400 will not make poor quality con-
Spillages of Conplast WP400 should be absorbed onto
crete waterproof. Good concrete practice must be followed
sand, earth or vermiculite and transferred to suitable con-
at all times. Well graded aggregates must be used and a
tainers. Hose down remnants with large quantities of water.
minimum cement content of 300 kg/m3 is recommended.
Consult the fact sheet available on the use of Conplast The disposal of excess or waste material should be carried
plasticisers in water retaining structures for further informa- out in accordance with local legislation under the guidance
tion. Adequate water bars must be provided between lifts of the local waste regulatory authority.
of concrete and floor bays. Conplast WP400 combined with
Conplast SP432MS produce high performance, low absorp- * Denotes the trademark of Fosroc International Limited
tion results.
†
See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
www.fosroc.com Qatar, Tadmur telephone: 4665501 fax: 4664147 email: [email protected]

UAE/0209/15/I