This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles

for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Designation: C31/C31M − 19a

Standard Practice for

Making and Curing Concrete Test Specimens in the Field1
This standard is issued under the fixed designation C31/C31M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.

1. Scope* 1.7 This international standard was developed in accor-

1.1 This practice covers procedures for making and curing dance with internationally recognized principles on standard-
cylinder and beam specimens from representative samples of ization established in the Decision on Principles for the
fresh concrete for a construction project. Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
1.2 The concrete used to make the molded specimens shall Barriers to Trade (TBT) Committee.
be sampled after all on-site adjustments have been made to the
mixture proportions, including the addition of mix water and 2. Referenced Documents
admixtures. This practice is not intended for making specimens 2.1 ASTM Standards:3
from concrete not having measurable slump or requiring other C125 Terminology Relating to Concrete and Concrete Ag-
sizes or shapes of specimens. gregates
1.3 1.3 This practice is not applicable to lightweight insu- C138/C138M Test Method for Density (Unit Weight), Yield,
lating concrete or controlled low strength material (CLSM). and Air Content (Gravimetric) of Concrete
NOTE 1—Test Method C495/C495M covers the preparation of speci- C143/C143M Test Method for Slump of Hydraulic-Cement
mens and the determination of the compressive strength of lightweight Concrete
insulating concrete. Test Method D4832 covers procedures for the C172/C172M Practice for Sampling Freshly Mixed Con-
preparation, curing, transporting and testing of cylindrical test specimens crete
of CLSM. C173/C173M Test Method for Air Content of Freshly Mixed
1.4 The values stated in either SI units or inch-pound units Concrete by the Volumetric Method
are to be regarded separately as standard. The values stated in C231/C231M Test Method for Air Content of Freshly Mixed
each system may not be exact equivalents; therefore, each Concrete by the Pressure Method
system shall be used independently of the other. Combining C330/C330M Specification for Lightweight Aggregates for
values from the two systems may result in non-conformance Structural Concrete
with the standard. C403/C403M Test Method for Time of Setting of Concrete
1.5 This standard does not purport to address all of the Mixtures by Penetration Resistance
safety concerns, if any, associated with its use. It is the C470/C470M Specification for Molds for Forming Concrete
responsibility of the user of this standard to establish appro- Test Cylinders Vertically
priate safety, health, and environmental practices and deter- C495/C495M Test Method for Compressive Strength of
mine the applicability of regulatory limitations prior to use. Lightweight Insulating Concrete
(Warning—Fresh hydraulic cementitious mixtures are caustic C511 Specification for Mixing Rooms, Moist Cabinets,
and may cause chemical burns to exposed skin and tissue upon Moist Rooms, and Water Storage Tanks Used in the
prolonged exposure.2) Testing of Hydraulic Cements and Concretes
1.6 The text of this standard references notes which provide C617/C617M Practice for Capping Cylindrical Concrete
explanatory material. These notes shall not be considered as Specimens
requirements of the standard. C1064/C1064M Test Method for Temperature of Freshly
Mixed Hydraulic-Cement Concrete
1
C1077 Practice for Agencies Testing Concrete and Concrete
This practice is under the jurisdiction of ASTM Committee C09 on Concrete
and Concrete Aggregates and is the direct responsibility of Subcommittee C09.61 Aggregates for Use in Construction and Criteria for
on Testing for Strength.
Current edition approved Dec. 15, 2019. Published February 2020. Originally
3
approved in 1920. Last previous edition approved in 2019 as C31/C31M–19. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/C0031_C0031M-19A. contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
2
See Section on Safety Precautions, Manual of Aggregate and Concrete Testing, Standards volume information, refer to the standard’s Document Summary page on
Annual Book of ASTM Standards, Vol. 04.02. the ASTM website.

*A Summary of Changes section appears at the end of this standard

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
1
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
Testing Agency Evaluation C470M. A suitable sealant, such as heavy grease, modeling
C1611/C1611M Test Method for Slump Flow of Self- clay, or microcrystalline wax shall be used where necessary to
Consolidating Concrete prevent leakage through the joints. Positive means shall be
C1758/C1758M Practice for Fabricating Test Specimens provided to hold base plates firmly to the molds. Reusable
with Self-Consolidating Concrete molds shall be lightly coated with mineral oil or a suitable
D4832 Test Method for Preparation and Testing of Con- nonreactive form release material before use.
trolled Low Strength Material (CLSM) Test Cylinders 5.2 Cylinder Molds—Molds for casting concrete test speci-
2.2 American Concrete Institute Publication:4 mens shall conform to the requirements of Specification
309R Guide for Consolidation of Concrete C470/C470M. Cardboard cylinder molds shall not be used for
standard-cured specimens.
3. Terminology
5.3 Beam Molds—Beam molds shall be of the shape and
3.1 For definitions of terms used in this practice, refer to
dimensions required to produce the specimens stipulated in 6.2.
Terminology C125.
The inside surfaces of the molds shall be smooth. The sides,
3.2 Definitions of Terms Specific to This Standard: bottom, and ends shall be at right angles to each other and shall
3.2.1 initial curing temperature, n—temperature of the en- be straight and true and free of warpage. Maximum variation
vironment surrounding the specimen during initial curing. from the nominal cross section shall not exceed 3 mm [1⁄8 in.]
3.2.1.1 Discussion—The environment surrounding the test for molds with depth or breadth of 150 mm [6 in.] or more.
specimens may be air, water, or sand. The temperature of the Molds shall produce specimens at least as long but not more
environment surrounding the test specimen might not be the than 2 mm [1⁄16 in.] shorter than the required length in 6.2.
same as the concrete temperature.
5.4 Tamping Rod—A round, smooth, straight, steel rod with
4. Significance and Use a diameter conforming to the requirements in Table 1. The
length of the tamping rod shall be at least 100 mm [4 in.]
4.1 This practice provides standardized requirements for greater than the depth of the mold in which rodding is being
making, curing, protecting, and transporting concrete test performed, but not greater than 600 mm [24 in.] in overall
specimens under field conditions. length (see Note 2). The rod shall have the tamping end or both
4.2 If the specimens are made and standard cured, as ends rounded to a hemispherical tip of the same diameter as the
stipulated herein, the resulting strength test data when the rod.
specimens are tested are able to be used for the following NOTE 2—A rod length of 400 mm [16 in.] to 600 mm [24 in.] meets the
purposes: requirements of the following: Practice C31/C31M, Test Method C138/
C138M, Test Method C143/C143M, Test Method C173/C173M, and Test
4.2.1 Acceptance testing for specified strength, Method C231/C231M.
4.2.2 Checking adequacy of mixture proportions for
strength, and 5.5 Vibrators—Internal vibrators shall be used. The vibrator
4.2.3 Quality control. frequency shall be at least 150 Hz [9000 vibrations per minute]
while the vibrator is operating in the concrete. The diameter of
4.3 If the specimens are made and field cured, as stipulated a round vibrator shall be no more than one-fourth the diameter
herein, the resulting strength test data when the specimens are of the cylinder mold or one-fourth the width of the beam mold.
tested are able to be used for the following purposes: Other shaped vibrators shall have a perimeter equivalent to the
4.3.1 Determination of whether a structure is capable of circumference of an appropriate round vibrator. The combined
being put in service, length of the vibrator shaft and vibrating element shall exceed
4.3.2 Comparison with test results of standard cured speci- the depth of the section being vibrated by at least 75 mm [3
mens or with test results from various in-place test methods, in.]. The vibrator frequency shall be checked periodically with
4.3.3 Adequacy of curing and protection of concrete in the a vibrating-reed tachometer or other suitable device.
structure, or
4.3.4 Form or shoring removal time requirements. NOTE 3—For information on size and frequency of various vibrators
and a method to periodically check vibrator frequency see ACI 309R.
5. Apparatus 5.6 Mallet—A mallet with a rubber or rawhide head weigh-
5.1 Molds, General—Molds for specimens or fastenings ing 0.6 6 0.2 kg [1.25 6 0.50 lb] shall be used.
thereto in contact with the concrete shall be made of steel, cast 5.7 Placement Tools—of a size large enough so each amount
iron, or other nonabsorbent material, nonreactive with concrete of concrete obtained from the sampling receptacle is represen-
containing portland or other hydraulic cements. Molds shall tative and small enough so concrete is not spilled during
hold their dimensions and shape under all conditions of use. placement in the mold. For placing concrete in a cylinder mold,
Molds shall be watertight during use as judged by their ability
to hold water poured into them. Provisions for tests of water TABLE 1 Tamping Rod Diameter Requirements
leakage are given in the Test Methods for Elongation, Diameter of Cylinder
Absorption, and Water Leakage section of Specification C470/ Diameter or Rod
or Width of Beam
mm [in.]
mm [in.]
<150 [6] 10 ± 2 [3⁄8 ± 1⁄16 ]
4
Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington $150 [6] 16 ± 2 [5⁄8 ± 1⁄16 ]
Hills, MI 48333-9094, http://www.aci-int.org.

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
2
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
the acceptable tool is a scoop. For placing concrete in a beam test result (Note 5). The same specimen size shall be used when
mold, either a shovel or scoop is permitted. comparing results and for mixture qualification and acceptance
5.8 Finishing Tools—a handheld float or a trowel. testing.
5.9 Slump Apparatus—The apparatus for measurement of NOTE 5—The modulus of rupture can be determined using different
slump shall conform to the requirements of Test Method specimen sizes. However, measured modulus of rupture generally in-
creases as specimen size decreases.5,6 The strength ratio for beams of
C143/C143M. different sizes depends primarily on the maximum size of aggregate.7
5.10 Sampling Receptacle—The receptacle shall be a suit- Experimental data obtained in two different studies have shown that for
able heavy gauge metal pan, wheelbarrow, or flat, clean maximum aggregate size between 19.0 and 25.0 mm [3⁄4 and 1 in.], the
ratio between the modulus of rupture determined with a 150 by 150 mm
nonabsorbent board of sufficient capacity to allow easy remix- [6 by 6 in.] and a 100 by 100 mm [4 by 4 in.] may vary from 0.90 to 1.075
ing of the entire sample with a shovel or trowel. and for maximum aggregate size between 9.5 and 37.5 mm [3⁄8 and 11⁄2
in.], the ratio between the modulus of rupture determined with a 150 by
5.11 Air Content Apparatus—The apparatus for measuring
150 mm [6 by 6 in.] and a 115 by 115 mm [4.5 by 4.5 in.] may vary from
air content shall conform to the requirements of Test Methods 0.86 to 1.00.6
C173/C173M or C231/C231M.
6.3 Field Technicians—The field technicians making and
5.12 Temperature Measuring Devices—The temperature curing specimens for acceptance testing shall meet the person-
measuring devices shall conform to the applicable require- nel qualification requirements of Practice C1077.
ments of Test Method C1064/C1064M.
7. Sampling Concrete
6. Testing Requirements
7.1 The samples used to fabricate test specimens under this
6.1 Cylindrical Specimens—Compressive or splitting tensile
standard shall be obtained in accordance with Practice C172/
strength specimens shall be cylinders cast and allowed to set in
C172M unless an alternative procedure has been approved.
an upright position. The number and size of cylinders cast shall
be as directed by the specifier of the tests. In addition, the 7.2 Record the identification of the sample with respect to
length shall be twice the diameter and the cylinder diameter the location of the concrete represented and the time of casting.
shall be at least 3 times the nominal maximum size of the
coarse aggregate. When the nominal maximum size of the 8. Slump, Slump Flow, Air Content, and Temperature
coarse aggregate exceeds 50 mm [2 in.], the concrete sample
shall be treated by wet sieving through a 50-mm [2-in.] sieve 8.1 Perform the following tests for each sample of concrete
as described in Practice C172/C172M. For acceptance testing from which specimens are made for acceptance testing for
for specified compressive strength, cylinders shall be 150 by strength:
300 mm [6 by 12 in.] or 100 by 200 mm [4 by 8 in.] (Note 4). 8.1.1 Slump or Slump Flow—After remixing the sample in
the receptacle, measure and record the slump or slump flow in
NOTE 4—When molds in SI units are required and not available, accordance with Test Method C143/C143M or Test Method
equivalent inch-pound unit size mold should be permitted.
C1611/C1611M, respectively.
6.2 Beam Specimens—Flexural strength specimens shall be 8.1.2 Air Content—Determine and record the air content in
beams of concrete cast and hardened in the horizontal position. accordance with either Test Method C173/C173M or Test
The length shall be at least 50 mm [2 in.] greater than three Method C231/C231M. The concrete used in performing the air
times the depth as tested. The ratio of width to depth as molded content test shall not be used in fabricating test specimens.
shall not exceed 1.5.
8.1.3 Temperature—Determine and record the temperature
6.2.1 The minimum cross-sectional dimension of the beam
in accordance with Test Method C1064/C1064M.
shall be as stated in Table 2. Unless otherwise specified by the
specifier of tests, the standard beam shall be 150 by 150 mm [6 NOTE 6—Some specifications may require the measurement of the unit
by 6 in.] in cross section. weight of concrete. The volume of concrete produced per batch may be
6.2.2 When the nominal maximum size of the coarse desired on some projects. Also, additional information on the air content
measurements may be desired. Test Method C138/C138M is used to
aggregate exceeds 50 mm [2 in.], the concrete sample shall be
measure the unit weight, yield, and gravimetric air content of freshly
treated by wet sieving through a 50-mm [2-in.] sieve as mixed concrete.
described in Practice C172/C172M.
6.2.3 The specifier of tests shall specify the specimen size
and the number of specimens to be tested to obtain an average 5
Tanesi, J; Ardani, A. Leavitt, J. "Reducing the Specimen Size of Concrete
Flexural Strength Test (AASHTO T97) for Safety and Ease of Handling," Trans-
portation Research Record: Journal of the Transportation Research Board, No.
2342, Transportation Research Board of National Academies, Washington, D.C.,
TABLE 2 Minimum Cross-Sectional Dimension of Beams 2013.
6
Nominal Carrasquillo, P.M. and Carrasquillo, R. L “Improved Concrete Quality Control
Minimum Procedures Using Third Point Loading”, Research Report 119-1F, Project 3-9-87-
Maximum
Cross-Sectional 1119, Center for Transportation Research, The University of Texas at Austin,
Aggregate
Dimension November 1987.
Size (NMAS)
7
# 25 mm [1 in.] 100 by 100 mm [4 by 4 in.] Bazant, Z. and Novak, D. "Proposal for Standard Test of Modulus of Rupture
25 mm [1 in.] < NMAS # 50 mm [2 in.] 150 by 150 mm [6 by 6 in.] of Concrete with its Size Dependence," ACI Materials Journal, January-February
2001.

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
3
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
9. Molding Specimens TABLE 4 Molding Requirements by Rodding
Number of
9.1 Place of Molding—Mold specimens promptly on a Specimen Type Number of Layers of
Roddings
level, rigid surface, free of vibration and other disturbances, at and Size Approximately Equal Depth
per Layer
a place as near as practicable to the location where they are to Cylinders:
be stored. Diameter, mm [in.]
100 [4] 2 25
9.2 Casting Cylinders—Select the proper tamping rod from 150 [6] 3 25
5.4 and Table 1 or the proper vibrator from 5.5. Determine the 225 [9] 4 50

method of consolidation from Table 3, unless another method Beams:

is specified. If the method of consolidation is rodding, deter- Width, mm [in.]
mine molding requirements from Table 4. If the method of 100 [4] to 2 see 9.3
200 [8]
consolidation is vibration, determine molding requirements >200 [8] 3 or more equal depths, see 9.3
from Table 5. Select a scoop of the size described in 5.7. While each not to exceed
placing the concrete in the mold, move the scoop around the 150 mm [6 in.].

perimeter of the mold opening to ensure an even distribution of

the concrete with minimal segregation. Each layer of concrete
TABLE 5 Molding Requirements by Vibration
shall be consolidated as required. In placing the final layer, add
Number of
an amount of concrete that will fill the mold after consolida- Specimen Type Number of Vibrator Approximate Depth of
tion. and Size Layers Insertions Layer, mm [in.]
9.2.1 Self-Consolidating Concrete—If casting cylinders of per Layer
self-consolidating concrete, use the mold filling procedures in Cylinders:
Diameter, mm [in.]
Practice C1758/C1758M instead of the procedure in 9.2. After 100 [4] 2 1 one-half depth of specimen
filling the mold, finish the cylinders in accordance with 9.5, 150 [6] 2 2 one-half depth of specimen
without further consolidation. 225 [9] 2 4 one-half depth of specimen

9.3 Casting Beams—Select the proper tamping rod from 5.4 Beams:
and Table 1 or proper vibrator from 5.5. Determine the method Width, mm [in.]
100 [4] to 1 see 9.4.2 depth of specimen
of consolidation from Table 3, unless another method is 200 [8]
specified. If the method of consolidation is rodding, determine over 200 [8] 2 or more see 9.4.2 200 [8] as near as
the molding requirements from Table 4. If the method of practicable

consolidation is vibration, determine the molding requirements

from Table 5. Determine the number of roddings per layer, one
for each 14 cm2 [2 in.2] of the top surface area of the beam.
Select a placement tool as described in 5.7. Using the scoop or and into the layer below approximately 25 mm [1 in.]. After
shovel, place the concrete in the mold to the height required for each layer is rodded, tap the outsides of the mold lightly 10 to
each layer. Place the concrete so that it is uniformly distributed 15 times with the mallet to close any holes left by rodding and
within each layer with minimal segregation. Each layer shall be to release any large air bubbles that may have been trapped.
consolidated as required. In placing the final layer, add an Use an open hand to tap cylinder molds that are susceptible to
amount of concrete that will fill the mold after consolidation. denting or other permanent distortion if tapped with a mallet.
9.3.1 Self-Consolidating Concrete—If casting beams of After tapping, spade each layer of the concrete along the sides
self-consolidating concrete, use the mold filling procedures in and ends of beam molds with a trowel or other suitable tool.
Practice C1758/C1758M instead of the procedure in 9.3. After Underfilled molds shall be adjusted with representative con-
filling the mold, finish the beams in accordance with 9.5, crete during consolidation of the top layer. Overfilled molds
without further consolidation. shall have excess concrete removed.
9.4.2 Vibration—Maintain a uniform duration of vibration
9.4 Consolidation—The methods of consolidation for this
for the particular kind of concrete, vibrator, and specimen mold
practice are rodding or internal vibration.
involved. The duration of vibration required will depend upon
9.4.1 Rodding—Place the concrete in the mold in the
the workability of the concrete and the effectiveness of the
required number of layers of approximately equal volume. Rod
vibrator. Usually sufficient vibration has been applied as soon
each layer uniformly over the cross section with the rounded
as the surface of the concrete has become relatively smooth and
end of the rod using the required number of strokes. Rod the
large air bubbles cease to break through the top surface.
bottom layer throughout its depth. In rodding this layer, use
Continue vibration only long enough to achieve proper con-
care not to damage the bottom of the mold. For each upper
solidation of the concrete (see Note 7). Fill the molds and
layer, allow the rod to penetrate through the layer being rodded
vibrate in the required number of approximately equal layers.
Place all the concrete for each layer in the mold before starting
TABLE 3 Method of Consolidation Requirements
vibration of that layer. In compacting the specimen, insert the
vibrator slowly and do not allow it to rest on the bottom or
Slump, mm [in.] Method of Consolidation
sides of the mold. Slowly withdraw the vibrator so that no large
$25 [1] rodding or vibration
< 25 [1] vibration air pockets are left in the specimen. When placing the final
layer, avoid overfilling by more than 6 mm [1⁄4 in.].

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
4
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
NOTE 7—Generally, no more than 5 s of vibration should be required for without proper support. Using a large trowel or a hand to support the
each insertion to adequately consolidate concrete with a slump greater bottom of these molds are acceptable means to prevent permanent
than 75 mm [3 in.]. Longer times may be required for lower slump deformation. It is acceptable to slightly tilt the mold to facilitate lifting and
concrete, but the vibration time should rarely have to exceed 10 s per supporting the mold. If a cover is to be placed on the top of a specimen,
insertion. the cover should be placed on the specimen after moving the specimen to
the initial curing location to ensure the required finish of the top surface
9.4.2.1 Cylinders—The number of insertions of the vibrator of the specimen. For example, if a specimen will be stored in water for
per layer is given in Table 5. When more than one insertion per initial curing, it would be appropriate to perform a final check of the
layer is required distribute the insertion uniformly within each surface finish prior to placing the cover and setting the specimen into the
layer. Allow the vibrator to penetrate through the layer being water.
vibrated, and into the layer below, about 25 mm [1 in.]. After 10.1.2 Initial Curing—Store standard-cured specimens for a
each layer is vibrated, tap the outsides of the mold at least 10 period up to 48 h after molding to maintain the specified
times with the mallet, to close holes that remain and to release temperature and moisture conditions described in 10.1.2.1 and
entrapped air voids. Use an open hand to tap molds that are 10.1.2.2.
susceptible to denting or other permanent distortion if tapped
NOTE 9—Generally, just covering the specimens is not sufficient to
with a mallet. maintain the environment required for initial standard curing.
9.4.2.2 Beams—Insert the vibrator at intervals not exceed-
ing 150 mm [6 in.] along the center line of the long dimension 10.1.2.1 For concrete mixtures with a specified strength less
of the specimen. For specimens wider than 150 mm [6 in.], use than 40 MPa [6000 psi], maintain the initial curing temperature
alternating insertions along two lines. Allow the shaft of the between 16 and 27°C [60 and 80°F]. For concrete mixtures
vibrator to penetrate into the bottom layer about 25 mm [1 in.]. with a specified strength of 40 MPa [6000 psi] or greater,
After each layer is vibrated, tap the outsides of the mold maintain the initial curing temperature between 20 and 26°C
sharply at least 10 times with the mallet to close holes left by [68 and 78°F]. Shield specimens from direct exposure to
vibrating and to release entrapped air voids. sunlight and, if used, radiant heating devices. Record the
minimum temperature and maximum temperatures achieved
9.5 Finishing—Perform all finishing with the minimum for each set of specimens during the initial curing period.
manipulation necessary to produce a flat even surface that is
level with the rim or edge of the mold and that has no NOTE 10—A satisfactory temperature environment can be created
during the initial curing of the specimens by one or more of the following
depressions or projections larger than 3.3 mm [1⁄8 in.]. procedures: (1) use of ventilation; (2) use of ice; (3) use of cooling
9.5.1 Cylinders—After consolidation, finish the top surfaces devices; or (4) use of heating devices such as electrical resistance heaters
by striking them off with the tamping rod where the consis- or light bulbs. Other suitable methods may be used provided the
tency of the concrete permits or with a handheld float or trowel. temperature requirements are met.
If desired, cap the top surface of freshly made cylinders with a NOTE 11—Early-age strength test results may be lower if specimens are
stored at temperatures lower than the specified range. At later ages,
thin layer of stiff portland cement paste which is permitted to strength test results may be lower if specimens are exposed to initial
harden and cure with the specimen. See section on Capping curing temperatures higher than the specified range.
Materials of Practice C617/C617M.
10.1.2.2 Store the specimens in an environment that con-
9.5.2 Beams—After consolidation of the concrete, use a
trols the loss of moisture.
handheld float or trowel to strike off the top surface to the
required tolerance to produce a flat, even surface. NOTE 12—A satisfactory moisture environment can be created during
the initial curing of the specimens by one or more of the following
9.6 Identification—Mark the specimens to positively iden- procedures: (1) immerse molded specimens with plastic lids in water; (2)
tify them and the concrete they represent. Use a method that store specimens in a container or enclosure; (3) place specimens in damp
will not alter the top surface of the concrete. Do not mark the sand pits; (4) cover specimens with plastic lids; (5) place specimens inside
removable caps. Upon removal of the molds, mark the test plastic bags; or (6) cover specimens with wet fabric.
NOTE 13—Immersion in water may be the easiest method to maintain
specimens to retain their identities. required moisture and temperature conditions during initial curing.

10. Curing 10.1.3 Final Curing:

10.1.3.1 Cylinders—Upon completion of initial curing and
10.1 Standard Curing—Standard curing is the curing within 30 min after removing the molds, cure specimens with
method used when the specimens are made and cured for the free water maintained on their surfaces at all times at a
purposes stated in 4.2. temperature of 23.0 6 2.0°C [73.5 6 3.5°F] using water stor-
10.1.1 Storage—The supporting surface on which speci- age tanks or moist rooms complying with the requirements of
mens are stored shall be level to within 20 mm/m [1⁄4 in./ft]. If Specification C511, except when capping with sulfur mortar
specimens are not molded in the location where they will capping compound and immediately prior to testing. When
receive initial curing, ensure that the specimens have been capping with sulfur mortar capping compound, the ends of the
moved to the initial curing location no later than 15 min after cylinder shall be dry enough to preclude the formation of steam
molding operations have been completed. If a specimen in a or foam pockets under or in cap larger than 6 mm [1⁄4 in.] as
single-use mold is moved, support the bottom of the mold. If described in Practice C617/C617M. For a period not to exceed
the top surface of a specimen is disturbed during movement to 3 h immediately prior to test, standard curing temperature is
the place of initial storage, refinish the surface. not required provided free moisture is maintained on the
NOTE 8—Some single-use molds, such as cylinder molds constructed of cylinders and ambient temperature is between 20 and 30°C [68
sheet metal or treated cardboard, may be permanently distorted if moved and 86°F ].

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
5
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
10.1.3.2 Beams—Beams are to be cured the same as cylin- given in 10.1.3.2 to guard against drying between time of
ders (see 10.1.3.1) except that they shall be stored in water removal from curing to testing.
saturated with calcium hydroxide at 23.0 6 2.0°C 10.3 Lightweight Concrete Curing—Cure lightweight con-
[73.5 6 3.5°F] at least 20 h prior to testing. Drying of the crete cylinders in accordance with Specification C330/C330M.
surfaces of the beam shall be prevented between removal from
water storage and completion of testing. 11. Transportation of Specimens to Laboratory
NOTE 14—Relatively small amounts of surface drying of flexural 11.1 Prior to transporting, cure and protect specimens as
specimens can induce tensile stresses in the extreme fibers that will required in Section 10. Specimens shall not be transported until
markedly reduce the indicated flexural strength. at least 8 h after final set. (See Note 15). During transporting,
10.2 Field Curing—Field curing is the curing method used protect the specimens with suitable cushioning material to
for the specimens made and cured as stated in 4.3. prevent damage from jarring. During cold weather, protect the
10.2.1 Cylinders—Store cylinders in or on the structure as specimens from freezing with suitable insulation material.
near to the point of deposit of the concrete represented as Prevent moisture loss during transportation by wrapping the
possible. Protect all surfaces of the cylinders from the elements specimens in plastic, wet burlap, by surrounding them with wet
in as near as possible the same way as the formed work. sand, or tight fitting plastic caps on plastic molds. Transporta-
Provide the cylinders with the same temperature and moisture tion time shall not exceed 4 h.
environment as the structural work. Test the specimens in the NOTE 15—Setting time may be measured by Test Method C403/
moisture condition resulting from the specified curing treat- C403M.
ment. To meet these conditions, specimens made for the
purpose of determining when a structure is capable of being put 12. Report
in service shall be removed from the molds at the time of 12.1 Report the following information to the laboratory that
removal of form work. will test the specimens:
10.2.2 Beams—As nearly as practicable, cure beams in the 12.1.1 Identification number,
same manner as the concrete in the structure. At the end of 12.1.2 Location of concrete represented by the samples,
48 6 4 h after molding, take the molded specimens to the 12.1.3 Date, time and name of individual molding
storage location and remove from the molds. Store specimens specimens,
representing pavements of slabs on grade by placing them on 12.1.4 Slump or slump flow, air content, and concrete
the ground as molded, with their top surfaces up. Bank the temperature, test results and results of any other tests on the
sides and ends of the specimens with earth or sand that shall be fresh concrete, and any deviations from referenced standard
kept damp, leaving the top surfaces exposed to the specified test methods, and
curing treatment. Store specimens representing structure con- 12.1.5 Curing method. For standard curing method, report
crete as near the point in the structure they represent as the initial curing method with maximum and minimum tem-
possible, and afford them the same temperature protection and peratures and final curing method. For field curing method,
moisture environment as the structure. At the end of the curing report the location where stored, manner of protection from the
period leave the specimens in place exposed to the weather in elements, temperature and moisture environment, and time of
the same manner as the structure. Remove all beam specimens removal from molds.
from field storage and store in water saturated with calcium
hydroxide at 23.0 6 2.0°C [73.5 6 3.5°F] for 24 6 4 h imme- 13. Keywords
diately before time of testing to ensure uniform moisture 13.1 beams; casting samples; concrete; curing; cylinders;
condition from specimen to specimen. Observe the precautions testing

SUMMARY OF CHANGES

Committee C09 has identified the location of selected changes to this practice since the last issue,
C31/C31M–19, that may impact the use of this practice. (Approved December 15, 2019.)

(1) Added 8.1 (3) Revised 1.2 and 10.3.

(2) Added Test Method C495/C495M and Test Method D4832 (4) Added Note 1.
to Referenced Documents.

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
6
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.
 C31/C31M − 19a
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

Copyright by ASTM Int'l (all rights reserved); Thu Oct 29 14:43:06 EDT 2020
7
Downloaded/printed by
Universidad De Antioquia (Universidad De Antioquia) pursuant to License Agreement. No further reproductions authorized.