ZVF300 Vector Inverter

User's Manual

Manufacturer:Zhejiang Ziri Electrical Technology Co.,Ltd.

Add:No.66,Daqiao Road,Liushi Town,Yueqing City,325604,
Zhejiang,China.
Tel:+86-577-27863300
Http://www.chziri.com
SOFTWARE VERSION:V3.69.

Printing Date:2020-6
 P1-P8
P1
P2
P2
P3
P5
P8
P9-P17
P9
P9
P9
P10
P13
P15
P18-P38
P18
P19
P24
P35
P39-P42
P39
 P43-P50
P43
P45
P51-P170
P51
6.2 Detailed function description P86
P171-P175
P171
P174
P176-P181
P176
P180
P181
P182-P185
P182
P185
P186
P186
P187-P214
P187
P190
P198
P214
40
method.
Figure 1-5. Three phase AC Power supply
 G3R7/P5R5

Motor Power Code

3R7 3.7kW
5R5 5.5kW

ZVF300-G3R7/P5R5T4MD
3.7/5.5kW

3PH 9.0/13A 0-600Hz

3. Cabinet Body
8.The door of cabinet
Inverter Model
Input Voltage Rated Output Adaptive Motor
(G：Constant torque load)
(V) Current (A) Power(kW)
(P：Variable torque load)

ZVF300-G0R4T2/S2 200-240 2.4 0.4

ZVF300-G0R7T2/S2 200-240 4.5 0.75

ZVF300-G1R5T2/S2 200-240 7.0 1.5

ZVF300-G2R2T2/S2 200-240 10.0 2.2

ZVF300-G3R7T2/S2 200-240 16.0 3.7

ZVF300-G5R5T2 200-240 20 5.5

ZVF300-G7R5T2 200-240 30 7.5

ZVF300-G011T2 200-240 42 11

ZVF300-G015T2 200-240 55 15

ZVF300-G018T2 200-240 70 18.5

ZVF300-G022T2 200-240 80 22

ZVF300-G030T2 200-240 110 30

ZVF300-G037T2 200-240 130 37

ZVF300-G045T2 200-240 160 45

ZVF300-G055T2 200-240 200 55

ZVF300-G075T2 200-240 270 75

ZVF300-G090T2 200-240 320 90

ZVF300-G110T2 200-240 380 110

ZVF300-G0R7T4 360-440 2.5 0.75

ZVF300-G1R5T4 360-440 3.7 1.5

ZVF300-G2R2T4 360-440 5.0 2.2

ZVF300-G3R7/P5R5T4 360-440 9.0/13 3.7

ZVF300-G5R5/P7R5T4 360-440 13/17 5.5/7.5

ZVF300-G7R5/P011T4 360-440 17/25 7.5/11

Inverter Model
Input Voltage Rated Output Adaptive Motor
(G：Constant torque load)
(V) Current (A) Power(kW)
(P：Variable torque load)

ZVF300-G011/P015T4 360-440 25/32 11/15

ZVF300-G015/P018T4 360-440 32/37 15/18.5

ZVF300-G018/P022T4 360-440 37/45 18.5/22

ZVF300-G022/P030T4 360-440 45/60 22/30

ZVF300-G030/P037T4 360-440 60/75 30/37

ZVF300-G037/P045T4 360-440 75/90 37/45

ZVF300-G045/P055T4 360-440 90/110 45/55

ZVF300-G055/P075T4 360-440 110/150 55/75

ZVF300-G075/P090T4 360-440 150/176 75/90

ZVF300-G090/P110T4 360-440 176/210 90/110

ZVF300-G110/P132T4 360-440 210/253 110/132

ZVF300-G132/P160T4 360-440 253/300 132/160

ZVF300-G160/P185T4 360-440 300/340 160/185

ZVF300-G185/P200T4 360-440 340/380 185/200

ZVF300-G200/P220T4 360-440 380/420 200/220

ZVF300-G220/P250T4 360-440 420/470 220/250

ZVF300-G250/P280T4 360-440 470/520 250/280

ZVF300-G280/P315T4 360-440 520/600 280/315

ZVF300-G315/P350T4 360-440 600/640 315/350

ZVF300-G350/P400T4 360-440 640/690 350/400

ZVF300-G400/P450T4 360-440 690/790 400/450

ZVF300-G450/P500T4 360-440 790/860 450/500

ZVF300-G500/P560T4 360-440 860/950 500/560

ZVF300-G560/P630T4 360-440 950/1100 560/630

ZVF300-G630T4 360-440 1100 630

 200-240VAC.
360-440VAC 50Hz/60Hz

-10 10

±5%

50.00Hz
 600
150 50
50
2.
 Braking unit Braking resistor

Three-phase
AC Input
Power supply

Error Relay Output

TA-TB on when normal
TA-TC on when failure

Open collector
Output

Potentiometer input Analog Signal Output

or analog voltage (0-10VDC or 0-20mA)
input (0-10VDC)

Analog current
input (0-20mA) Analog Signal Output
( 0-20mA)

RS485 COM Port 24V Power Output Port

Applicable to model:
ZVF300-G0R4S2～3R7S2 ZVF300-G0R4T2～7R5T2
ZVF300-G0R7T4～018T4 ZVF300-P5R5T4～022T4
 Braking unit Reactor

Three-phase
AC Input
Power supply

Error Relay Output

TA-TB on when normal
TA-TC on when failure

Open collector
Output

Potentiometer input Analog Signal Output

or analog voltage (0-10VDC or 0-20mA)
input (0-10VDC)

Analog current
input (0-20mA) Analog Signal Output
( 0-20mA)

Rs485 COM Port 24V Power Output Port

diagram

Applicable to model ：
ZVF300-G011T2～ 110T2
ZVF300-G022T4～ 630T4 ZVF300-P030T4～630T4

A01
P5R5T4
motor
 630T4
630T4
G011T2~G110T2, G022T4~P315T4

The inverter from G075T2, G160T4/P185T4 and above are cabinet installation .
It’s necessary to add DC reactor .
 TA T B T C +10V AVI ACI GND AO1 AO2 Y 1 Y2 COM
X1 X 2 X 3 X 4 X 5 X6 X7 X8 COM PLC +24V 485+ 485-

+10VAVI 485+ 485- X1 X2 X3 X4 COM Y1 Y2 COM +24V TB

ACI GND AO1 AO2 PE X5 X6 X7 X8 COM PLC +24V TA TC
 Terminal
Types Function Description Electrical Specifications
Symbols

Public port Digital signal

COM
public terminal

X1

X2

X3 Valid only when there is

Multi- a short circuit between
function X4 Xn (n=1, 2, 3, 4,5, 6,7,8) INPUT, 0~24 power level,
Input X5 and COM. The functions low level valid,5mA
Terminal can be set by the parameter
X6 F5.00~F5.07separately.

X7

X8

Public port
for
Digital signal public
Multi-function PLC
port selection terminal
Input
Terminal

Y1 Multi-function open collector

Multi- output is defined as
function on-off output terminal, whose
OUTPUT, Maximum Current I≤50mA
output function is set by the
Terminal parameter F6.00~F6.01 with
Y2 reference of COM.

Others PE Ground Terminal

 OUTPUT, 0-10v DC voltage
AO1
Programmable analog output OUTPUT 0-20mA DC Current
with reference of GND.
AO2 OUTPUT 0-20mA DC Current

+24VDC

NC : 240VAC-3A
NO: 240VAC- 1A

Communication 485+ Communication signal positive

Terminal 485- Communication signal negative

 Main Circuit（mm2） Control
Brake Switch
Inverter Model Wire
Capacity (A) Input Wire Output Wire （mm ）
2

ZVF300-G0R4T2/S2 6/16 2.5 2.5 0.75

ZVF300-G0R7T2/S2 10/20 2.5 2.5 0.75

ZVF300-G1R5T2/S2 10/20 2.5 2.5 0.75

ZVF300-G2R2T2/S2 16/32 4 4 0.75

ZVF300-G3R7T2/S2 25 4 4 0.75

ZVF300-G5R5T2 32 6 6 0.75

ZVF300-G7R5T2 50 6 6 0.75

ZVF300-G011T2 63 10 10 0.75

ZVF300-G015T2 80 16 16 0.75

ZVF300-G018T2 100 25 25 0.75

ZVF300-G022T2 125 25 25 0.75

ZVF300-G030T2 160 35 35 0.75

ZVF300-G037T2 200 50 50 0.75

ZVF300-G045T2 225 70 70 0.75

ZVF300-G055T2 315 95 95 0.75

ZVF300-G075T2 400 120 120 0.75

ZVF300-G090T2 500 150 150 0.75

ZVF300-G110T2 500 185 185 0.75

ZVF300-G0R7T4 6 2.5 2.5 0.75

ZVF300-G1R5T4 6 2.5 2.5 0.75

ZVF300-G2R2T4 10 2.5 2.5 0.75

ZVF300-G3R7T4 16 4 4 0.75

ZVF300-G5R5/P5R5T4 20 4 4 0.75

ZVF300-G7R5/P7R5T4 25 6 6 0.75
 Main Circuit（mm2） Control
Brake Switch
Inverter Model Wire
Capacity (A) Input Wire Output Wire （mm ）
2

ZVF300-G011/P011T4 40 6 6 0.75

ZVF300-G015/P015T4 50 10 10 0.75

ZVF300-G018/P018T4 63 10 10 0.75

ZVF300-G022/P022T4 80 16 16 0.75

ZVF300-G030/P030T4 80 16 16 0.75

ZVF300-G037/P037T4 100 25 25 0.75

ZVF300-G045/P045T4 125 25 25 0.75

ZVF300-G055/P055T4 160 35 35 0.75

ZVF300-G075/P075T4 225 50 50 0.75

ZVF300-G090/P090T4 250 70 70 0.75

ZVF300-G110/P110T4 315 95 95 0.75

ZVF300-G132/P132T4 400 120 120 0.75

ZVF300-G160/P160T4 400 150 150 0.75

ZVF300-G185/P185T4 500 150 150 0.75

ZVF300-G200/P200T4 500 185 185 0.75

ZVF300-G220/P220T4 630 95×2 95×2 0.75

ZVF300-G250/P250T4 630 120×2 120×2 0.75

ZVF300-G280/P280T4 700 150×2 150×2 0.75

ZVF300-G315/P315T4 800 150×2 150×2 0.75

ZVF300-G350/P350T4 800 185×2 185×2 0.75

ZVF300-G400/P400T4 1000 185×2 185×2 0.75

ZVF300-G450/P450T4 1000 185×2 185×2 0.75

ZVF300-G500/P500T4 1250 185×3 185×3 0.75

ZVF300-G560/P560T4 1250 185×3 185×3 0.75

ZVF300-G630/P630T4 1600 185×3 185×3 0.75

AO1
AO1
 AO1

15
AO1
 Setting/Given Signal

Feedback signal
AO1

F0.01- Running channel source selection .F0.01=1-External terminal control.

 0.03-Main frequency channel source selection. F0.03=5-PID Control.
F
 5.00-Input terminal X1 function selection .F5.00=1-Forward Running.
F
 5.01- Input terminal X2 function selection .F5.01=7-External reset input.
F
 9.00-PIDpreset source selection .F9.00=1-Select external voltage
F
or potentiometer setting.
 9.02—PID Feedback value source selection. F9.02=1-Select external current
F
feedback.
 9.03-PID output characteristic selection.F9.03=0-Select positive feedback.
F
 9.04—Proportional gain Kp: Set according to the actual request.
F
F9.05—Integral time Ti. Set according to the actual request.

 9.06—Differential time Td. Set according to the actual request.
F
 9.07-Sampling cycle T: No need to change.
F
 9.08-Bias limit .Set according to the actual request.
F
 9.11— feedback gain :Set according to actual request.
F
 9.12—Awakening threshold width. Set according to the actual request.
F
 9.13—Awakening Threshold detection time . Set according to the actual request.
F
 9.14—Sleep Frequency.Set according to the actual request.
F
 9.15—Sleep Frequency Detection Time. Set according to the actual request.
F
 9.16-The range of gauge: Set according to the actual request.
F
 Chapter 6 Detailed function description

Chapter 6 Detailed function description

6.1 Function Parameters

6.1.1 F0 Group Basic function

Runn
Factory ing
Code Name Setting Range Min.Unit
setting Modifi
cation

0：NO PG vector control

1：V/F control
2：Torque control
F0.00 Speed control mode 1 1 ×
(NO PG Vector Control)
3.Reserve
4.PG vector control

0：Keyboad command channel

Running command
F0.01 1：Terminal command channel 1 0 ×
channel
2:Communication command channel

-51-
 Chapter 6 Detailed function description

6.1.1 F0 Group Basic function(Continued)

Runn
Factory ing
Code Name Setting Range Min.Unit
setting Modifi
cation

0：Valid , save the parameters when

the inverter is powered off
1：Valid .the value can not be saved
Keyboard and
when the inverter is powered off
F0.02 terminal 1 0 √
2：UP/DOWN setting is invalid
UP/Down setting
3：Valid during running ,clear when
the inverter stops .
4.Valid when F0.03=0.

0: Keyboard or encoder setting

1: AVI
2: ACI
3: AVI+ ACI
4: keyboard potentiometer setting
5: Water supply PID control setting
6: Remote communication setting
Frequency
7: External pulse setting
F0.03 command 1 0 √
8: AVI(host )±ACI(assit )
selection
combination setting
9: Keyboard(host)±ACI(assit)
combination setting .
10: Communication(Host) ±ACI
(assit)combination setting .
11: Combination
12: Common PID control setting

Maximum
F0.04 10.00～600.00Hz 0.01Hz 50.00Hz ×
output frequency .

Upper limit
F0.05 F0.06～F0.04（Max. Frequency） 0.01Hz 50.00Hz √
frequency

Lower limit 0.00～F0.05

F0.06 0.01Hz 0.00Hz √
frequency （Running frequency upper limit）

-52-
 Chapter 6 Detailed function description

6.1.1 F0 Group Basic function(Continued)

Runn
Factory ing
Code Name Setting Range Min.Unit
setting Modifi
cation

keypad setting
F0.07 0.00～F0.04（Max. Frequency） 0.01Hz 50.00Hz √
frequency

Acceleration Depend on
F0.08 0.1～3600.0s 0.1s √
time 1 the model

Deceleration Depend on
F0.09 0.1～3600.0s 0.1s √
time 1 the model

0：Forward
Running direction (the default running direction)
F0.10 1 0 ×
selection 1：Reverse
2：Forbid reverse

Depend on
F0.11 Carrier frequency 1.0～15.0kHz 0.1kHz √
the model

0：No action
Motor parameters
1：Rotation autotuning
F0.12 autotuning 1 0 ×
2：Static autotuning

0: No action
1: Restore the default value
Restore all parameters FO-Fd to factory
setting except F2 group
F0.13 Restore parameters 2: Clear fault records 1 0 ×
Inverter clear all fault records.
3 Restore the default value to380V/60Hz.
4: Restore the default value to 440V /50Hz.
5: Restore the default value to 440V /60Hz.

0：Disable
F0.14 AVR Fcuntion 1：Enable all the time 1 0 √
2:Disabled during deceleration

-53-
 Chapter 6 Detailed function description

6.1.1 F0 Group Basic function(Continued)

Runn
Factory ing
Code Name Setting Range Min.Unit
setting Modifi
cation

LED Unit’s Place: Operand 1

LED Decade: Operand 2
LED Hundreds place: Operand 3
Thousands place： Reserved
0:Keypad Potentiometer
Combination 1:Keypad or Encoder
F0.15
channel setting 2.Reseve
1 - 000 √
3:Communication
4:AVI
5:ACI
6: External pulse setting
7: Multi-speed stage

LED Unit’s Place: Algorithm 1

LED Decade: Algorithm 2
LED Hundreds 、
Thousands place： Reserved.
Combination 0：Addition
F0.16 1 --00 √
algorithm Setting 1：Subtraction
2：The absolute value (Subtraction)
3：Maximized
4: Minimized
5: No calculation If operand is 3.

F0.17 Parameter Locked 0: Invalid 1: Valid 1 0 ×

Acc/Dec Mode
F0.18 0:Linear 1:S Curve 1 0 ×
Selection

Temperature alarm 0: Invalid

F0.19 0 0 √
switch 1: Valid

Alarm temperature
F0.20
value

-54-
 Chapter 6 Detailed function description

6.1.2 F1 Group start and stop control

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0：Start directly
F1.00 Start Mode 1：DC braking and start 1 0 ×
2：Speed tracking starting

Direct starting
F1.01 0.00～50.00Hz 0.01Hz 1.50Hz √
frequency

Starting frequency
F1.02 0.0～50.0s 0.1s 0.0s √
maintain time

DC braking current
F1.03 0.0～150.0% 0.1% 0.0% √
before start

DC braking time
F1.04 0.0～50.0s 0.1s 0.0s √
before start

0：Ramp to stop
F1.05 Stop mode 1：Coast/Free stop 1 0 √
2: Deceleration stop +Free stop

Starting frequency
F1.06 of DC braking 0.00～F0.04（Max.frequency） 0.01Hz 0.00Hz √
at stopping

Braking wait time

F1.07 0.0～50.0s 0.1s 0.0s √
at stopping

-55-
 Chapter 6 Detailed function description

6.1.2 F1 Group start and stop control(Continued)

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

DC braking current
F1.08 0.0～150.0% 0.1% 0.0% √
at stopping

DC braking time
F1.09 0.0～50.0s 0.1s 0.0s √
at stopping

Dead time of
F1.10 0.0～3600.0s 0.1s 0.0s √
FWD/REV

0：Command invalid when

Terminal running
powered on
F1.11 protection selection 1 0 √
1：Command valid when
when power on
powered on

Input/Output
F1.12 terminal polarity 0x000～0x7FF 1 0x000 √
selection

1.Disabled
Power off Restart
F1.13 2.Regular Start 1 0 ×
Mode Selection
3.Start with rotary tracing

Power Cut
F1.14 0.0-20.0S 0.1 0.5S ×
Restart Wait Time

-56-
 Chapter 6 Detailed function description

6.1.3 F2 Group Motor parameters

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0：G Type Depend on

Inverter Type 1
F2.00 1：P Type model ×

Depend on
F2.01 Motor rated power 0.4～700.0kW 0.1kW ×
model

Motor rated
F2.02 0.01～600.00Hz 0.01Hz 50.00Hz ×
frequency

Motor rated Depend on

F2.03 0～36000rpm 1rpm ×
rotate speed model

Depend on
F2.04 Motor rated voltage 0～460V 1V ×
model

Depend on
F2.05 Motor rated current 0.1～2000.0A 0.1A ×
model

Motor stator Depend on

F2.06 0.001～65.535Ω 0.001Ω √
resistance model

Motor rotor Depend on

F2.07 0.001～65.535Ω 0.001Ω √
resistance model

Motor leackage Depend on

F2.08 0.1～6553.5mH 0.1mH √
inductance model

Motor mutual Depend on

F2.09 0.1～6553.5mH 0.1mH √
inductace model

Motor Current Depend on

F2.10 0.01～655.35A 0.01A √
without load model

-57-
 Chapter 6 Detailed function description

6.1.4 F3 Group Vector control

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Proportional gain
F3.00 0～10000 1 15 √
1 of speed loop

Integration time 1
F3.01 of speed loop 0.01～100.00s 0.01s 2.00s √

Low switching point

F3.02
frequency 0.00～F3.05 0.01Hz 5.00Hz √

Proportional gain 2
F3.03
of speed loop 0～10000 1 10 √

Integration time 2
F3.04
of speed loop 0.01～100.00s 0.01s 3.00s √

High switching
F3.05
point frequency F3.02～F0.04（Max. Frequency） 0.01Hz 10.00Hz √

Slip compensation
F3.06
rate of VC
50～200% 1% 100% √

Torque upper-limit
F3.07
setting
0.0～200.0%（Inverter rated current） 0.1% 150.0% √

Torque dynamic
F3.08
friction coefficient
0.000～1.000 0.001 0.125 √

Empty load current

F3.09 compensation 0.000～9.999 0.001 0.800 √
coefficients

Torque static
F3.10 0.00-10.00 0.001 2.00 √
friction coefficient

-58-
 Chapter 6 Detailed function description

6.1.5 F4 Group V/F Control

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
0: Linear V/F Curve
1:Square V/F Curve
2:User Setting V/F Curve
F4.00 V/F Curve Setting 3.1.25power V/F Curve 1 0 ×
4.1.7 power V/F Curve
5. 3 power V/F Curve
6. 4 power V/F Curve

0.0%：(auto)
F4.01 Torque Boost 0.1% 0.0% √
0.1～30.0％
0.0～50.0%
F4.02 Torque boost cutoff
（Relative to the rated motor frequency）
0.1% 20.0% ×

V/F Slip
F4.03
compensation limit
0.0～100.0% 0.1% 0.0% √

Auto energy 0：Disable

F4.04
saving selection 1：Enabled
1 0 ×

F4.05 Reserved -

V/F Frequency
F4.06
Value F1
0-F4.08 0.01Hz 12.5Hz √

V/F Voltage
F4.07
Value V1
0-F4.09 0.01% 25.00% √

V/F Frequency
F4.08
Value F2
F4.06-F4.10 0.01Hz 25.00Hz √

V/F Voltage
F4.09
Value V2
F4.07-F4.11 0.01% 50.00% √

V/F Frequency
F4.10
Value F3 F4.08-F0.05 0.01Hz 37.50Hz √

V/F Voltage
F4.11
Value V3 F4.09-100.00% 0.01% 75.00% √

Low voltage 0：Enabled

F4.12
protection selection 1：Disable
1 0 √

-59-
 Chapter 6 Detailed function description

6.1.6 F5 Group Input terminal

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

X1 terminal 0：No function

F5.00 function selection 1：Forward running 1 1 ×
2：Reverse running
3：3-Wire running control
4：Jog forward control
X2 terminal 5：Jog reverse control
F5.01 function selection 6：Coast to stop 1 2 ×
7：Reset fault;
8：External fault input
9：Frequency UP command（UP）
X3 terminal 10：Frequency DOWN command(DOWN)
F5.02 function selection 11：Clear frequency UP/DOWN 1 7 ×
12：Multi-step speed terminal 1
13：Multi-step speed terminal2
14：Multi-step speed terminal 3
15：Multi-step speed terminal 4
X4 terminal
F5.03 function selection
16：Acceleration and deceleration
1 0 ×
time selection
17：PID control pause
18：Traverse frequency pause
(stop at the current frequency)
X5 terminal 19：Traverse frequency reset
F5.04 function selection 1 0 ×
( return to the centre frequency).
20：Acceleration and deceleration
prohibition
21：Disable torque control
X6 terminal 22：Clear frequency acc.and dec. settings
F5.05
function selection 23：DC braking when stopping
1 0 ×
24：External pulse input
25： Frequency switch to ACI
26: Frequency switch to AVI
X7 terminal 27:Reserved
F5.06 28: Coast to stop control 1 0 ×
function selection
29: Running command switch to terminal
30:PLC reset
31: PLC input
X8 terminal 32: Count input
F5.07 33. Frequency switch to the combination 1 0 ×
function selection
34: Count clear

-60-
 Chapter 6 Detailed function description

6.1.6 F5 Group Input terminal(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

F5.08 ON/OFF filter times 1～100 1 5 √

0：2-wire control mode 1

Terminal control 1：2-wire control mode 2
F5.09 1 0 ×
running mode 2：3-wire control mode 1
3：3-wire control mode 2

UP/DOWN terminal
F5.10 0.01～50.00Hz/s 0.01Hz/s 0.50Hz/s √
change speed rate

F5.11 AVI lower limit

0.00～10.00V
0.01V 0.00V √

AVI lower limit

F5.12 corresponding setting -100.0～100.0% 0.1% 0.0% √

F5.13 AVI upper limit 0.00～10.00V 0.01V 10.00V √

AVI upper limit

F5.14 corresponding setting -100.0～100.0% 0.1% 100.0% √

F5.15 AVI input filter time 0.00～10.00s 0.01s 0.10s √

ACI lower limit 0.00～10.00V 0.01V 0.00V

F5.16 √

ACI lower limit

0.1% 0.0%
F5.17 corresponding setting -100.0～100.0% √

-61-
 Chapter 6 Detailed function description

6.1.6 F5 Group Input terminal(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

F5.18 ACI upper limit 0.00～10.00V 0.01V 10.00V √

ACI upper limit

F5.19 -100.0～100.0% 0.1% 100.0% √
corresponding setting

F5.20 ACI input filter time 0.00～10.00s 0.01s 0.10s √

Frequency of
F5.21 0.00~F0.05 0.01Hz 30.00Hz √
free stop

pulse input
F5.22 0.0～20.0kHz 0.1kHz 0.0kHz √
lower limit

pulse input lower

F5.23 limit corresponding -100.0～100.0% 0.1% 0.0% √
setting

pulse input
F5.24 0.0～20.0kHz 0.1kHz 10.0kHz √
upper limit

pulse input upper

F5.25 limit corresponding -100.0～100.0% 0.1% 100.0% √
setting

Center voltage
F5.26 0.00～10.00V 0.01V 0.15V √
hysteresis loop width

0:Auto operation : The fan will run

when the inverter starts . and will
Cooling Fan
F5.27 stop when the inverter stops. 1 0 ×
control
1:The cooling fan is running when
the inverter energized on .

-62-
 Chapter 6 Detailed function description

6.1.7 F6 Group Output terminal

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0:No output
1：Forward running
F6.00 Y1 output selection 2：Reverse running 1 √
3：Fault output
4：Frequency level detection
FDT output
5：frequency reached
6：Zero speed running
7：Upper limit frequency reached
F6.01 Y2 output selection 1 2 √
8：Lower limit frequency reached
9:Running
10: PLC stage completed
11:PLC cycle completed
12: Overload Pre-alarm
13: Specified count value reached
Relay output
F6.02 14:Setting count value reached 3 √
selection
15: Reserved
16:Under load output

0：Running frequency
1：Setting frequency
2：Motor speed
3：Output current
AFM output 4：Output Voltage
F6.03 1 0 √
selection 5：Output power
6：Output torque
7：Analog AVI input
8：Analog ACI input
9～14：Reserved

AFM output
F6.04 0.0～100.0% 0.1% 0.0% √
lower limit

-63-
 Chapter 6 Detailed function description

6.1.7 F6 Group Output terminal(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
The lower limit
√
F6.05 corresponding to 0.00～10.00V 0.01V 0.00V
the AFM output

AFM output
F6.06 0.1% 100.0% √
upper limit 0.0～100.0%

The upper limit

F6.07 corresponding to 0.00～10.00V 0.01V 10.00V √
the AFM output

F6.08 DFM output selection 0～14（same as F6.03） 0 0 √

0.0～100.0%
F6.09 DFM output lower limit 0.1% 0.0% √

The lower limit

0.0～10.0kHz
F6.10 corresponding to 0.1kHz 0.0kHz √
the DFM output

0.0～100.0% √
F6.11 DFM output upper limit 0.1% 100.0%

The lower limit

F6.12 corresponding to 0.0～10.0kHz 0.1kHz 10.0kHz √
the DFM output

Y1 delay conduction
F6.13 0.1～3600.0s 0.1s 0.0s √
time

Y1 delay shut
F6.14 0.1～3600.0s 0.1s 0.0s √
off time

-64-
 Chapter 6 Detailed function description

6.1.7 F6 Group Output terminal(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Y2 delay √
F6.15 0.1～3600.0s 0.1s 0.0s
conduction time

Y2 delay √
F6.16 0.1～3600.0s 0.1s 0.0s
shut off time

Relay delay
F6.17 0.1～3600.0s 0.1s 0.0s √
closing time

Relay delay
F6.18 0.1～3600.0s 0.1s 0.0s √
disconnect time

F6.19 Set the count value 0～9999 1 0 √

Specified the
F6.20 0～F6.19 1 0 √
count value

F6.21 The count coefficient 0.01～99.99 0.01 1.00 √

LED Unit’s Place：Clear mode

0：Auto
1：Manual
Counter working LED Decade：Count mode
F6.22
mode selection 0：Up counter 1 - - 00 √
1：Down counter
LED Hundreds 、Thousand
place Reserved

-65-
 Chapter 6 Detailed function description

6.1.8 F7 Group Human-machine interface

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

F7.00 The user password 0～65535 1 0 √

LED Unit’s Place、Decade: Running

status display options 0x00-0x1F
The initial selection
F7.01 LED hundred’s place、Thousand 1 0x0000 -
when Power on
place: Stop status display options
0x00-0x0c

0:Invalid
1:The parameters will download from
the control board to the deypad.
2:The parameters will download from
the keypad to the control board
F7.02 Parameter Copy -
(Includes motor parameters)
3:Reserve
4:The parameters will download from
the keypad to the control board.
(Without motor parameters).

0：Jog operation
1：FWD/REV switching
REV/JOG function
F7.03 2：Clear UP/DOWN setting 1 0 ×
selection
3:Reverse Running
4:Fast search

0：Valid when keypad control

1：Valid when keypad or terminal
STOP/RESET key
control
F7.04 stop function 1 0 √
2：Valid when keypad or
selection
communication control
3：Always valid

Gauge Range
F7.05 0-3 1 2 √
Decimal Place

-66-
 Chapter 6 Detailed function description

6.1.8 F7 Group Human-machine interface(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0~0xFFFF
BIT0：Running frequency
BIT1：Setting frequency
BIT2：DC bus voltage
BIT3：Output voltage
BIT4：Output current
BIT5：running rotation speed
Running state display BIT6：output power
F7.06 BIT7：output torque 1 0x00FF √
parameter selection 1 BIT8：PID setting
BIT9：PID feedback
BIT10：Input terminal state
BIT11：Output terminal state
BIT12：Analog AVI Setting
BIT13：Analog ACI Setting
BIT14：The current step of multi-step
BIT15：Torque setting value

0-0X3
BIT0：Count value
Running state display BIT1：Linkage proportion coefficient
F7.07 BIT2: PLC average speed 1 0x0 √
parameter selection 2
BIT3: The Current speed of PLC.
BIT4: The current running remaining
time of PLC .

1~0x1FFF
BIT0: setting frequency
BIT1: DC bus voltage
BIT2: Input terminal state
BIT3: Output terminal state
BIT4: PID setting value
BIT5: PID feedback value
Stop state display BIT6: Analog AVI value
BIT7: Analog ACI value
F7.08 parameter 1 0x40F √
BIT8: The current step of multi-step
selection BIT9: Torque setting value
BIT10: Input AC voltage
BIT11: Count Value
BIT12: Linkage proportion coefficien
BIT13: PLC average speed
BIT14: The Current speed of PLC
BIT15: The current running remaining
time of PLC .

-67-
 Chapter 6 Detailed function description

6.1.8 F7 Group Human-machine interface(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

IGBT module
F7.09 0～100.0℃ 0.1℃ -
temperature

F7.10 Software version 0.00～99.9 1.00 -

Accumulated
F7.11 0～65535h 1h 0 -
running time

Runtime password
F7.12 0～65535 1 0 ×
setting

F7.13 Runtime setting 0～65535h 1h 0 ×

0～29
0：No fault （nonE）
1:over current when acceleration
（ocA）
2：over current when decleration
（ocd）
3：over-current when constant
speed running （ocn）
The previous
F7.14 4：Over –voltage when when -
two fault type
acceleration（ovA）
5：over-voltage when decleration
（ovd）
6：Over-voltage when constant
running （ovn）
7：over-voltage when stopping
（ovS）
8：DC bus under voltage （Lv）

-68-
 Chapter 6 Detailed function description

6.1.8 F7 Group Human-machine interface(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

9：Input phase failure （LP）

10：Output short circuit（SC）
11：inverter overheat （OH1）
12：Motor overload（OL1）
The previous 13：Inverter overload （OL2）
F7.15 -
fault type 14：External fault （EF）
15：RS485 communication fault CE-1）
16：Reserved
14：External fault （EF）
15：RS485 communication fault （CE-1）
16：Reserved
17：Current detection fault（ItE）
18：keypad communication fault（CE-4）
19：Autotuning falut （tE）
20：EEPROM fault （EEP）
The current 21：PID feedback fault （PIDE）
F7.16 -
fault type 22～24：Recerved
25：dCE
26～27：Reserved
28：Output phase failure （SPO）
29：Reserved

The current fault

F7.17 0.00～600.00Hz 0.01Hz -
running frequency

The current fault

F7.18 0.1～3000.0A 0.1A -
output current

The current fault 0～1000V

F7.19 1V -
DC bus voltage

The current
F7.20 0-100.00℃ 0.1℃ -
fault temperature

The current fault

F7.21 0～0xFFFF 1 0 -
input terminal state

The current fault

F7.22 0～0xFFFF 1 0 -
output terminal state

-69-
 Chapter 6 Detailed function description

6.1.9 F8 Group-Enhanced function

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Depend on
F8.00 Acceleration time 2 0.1～3600.0s 0.1s √
the model

Depend on
F8.01 Deceleration time 2 0.1～3600.0s 0.1s √
the model
Jog running
F8.02 0.00～F0.04（Max.frequency） 0.01Hz 5.00Hz √
frequency

Jog acceleration Depend on

F8.03 0.1～3600.0s 0.1s √
time the model

Jog deceleration Depend on

F8.04 0.1～3600.0s 0.1s √
time the model

F8.05 Skip frequency 0.00～F0.04（Mex.frequency） 0.01Hz 0.00Hz √

Skip frequency
F8.06 0.00～F0.04（Max.frequency） 0.01Hz 0.00Hz √
bandwidth
0.0～100.0%
F8.07 Traverse amplitude 0.1% 0.0% √
（Relative to the setting frequency）

Jitter frequency 0.0～50.0%

F8.08 0.1% 0.0% √
bandwidth (Relative to the traverse amplitude)

F8.09 Rise time of traverse 0.1～3600.0s 0.1s 5.0s √

F8.10 Fall time of traverse 0.1～3600.0s 0.1s 5.0s √

F8.11 Fault auto reset times 0～9999 0 0 √

Fault reset
F8.12 0.1～100.0s 0.1s 1.0s √
interval time

F8.13 FDT Level 0.00～ F0.04(Max.frequency) 0.01Hz 50.00Hz √

F8.14 FDT lag 0.0～100.0%（FDT level ） 0.1% 5.0% √

Frequency arrival
F8.15 0.0～100.0%（Max.frequency） 0.1% 0.0% √
detecting range

-70-
 Chapter 6 Detailed function description

6.1.9 F8 Group-Enhanced function(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
380V Series ：
115.0～140.0% 0.1% 125.0% √
Energy braking （Stardard DC bus voltage）
F8.16
threshold voltage 220V Series：
115.0～140.0% 0.1% 115.0% √
（Stardard DC bus voltage）
0.1～999.9%
Coefficient of Actual mechanical speed=120*
F8.17 output frequency *F8.17/Number
0.1% 100.0% √
rotation speed
of poles of motor .
Enery braking output
F8.18 0-100% 1% 0% √
starting value
LED bit.overload pre-alarm detection selection
0: No detection
1: Running Detection
2:Constant speed detection
LED ten digit. overload pre-alarm action selection
Over load/Under load 0: No alarm, continue running
1: OL3 alarm, stop running.
F8.19 pre-alarm protection LED Hundred digit.under load pre-alarm detection selection 1 00 √
0: No detection
selection 1: Under load when Running Detection
2: Under load when Constant speed detection
LED Thousand digit .under load pre-alarm action selection
0:No Alarm . Continue running
1: UL4 Alarm .stop running .

Overload
F8.20 0.0～150.0% 0.1% 130.0% √
pre-alram level
Overload
F8.21 0.0～6500.0s 0.1s 5.0s √
detection time
The decrease rate of
F8.22 0.00～15.00% 0.01% 0.00% √
drop control frequency

Units digit: 0: ENA OFF. 00 00 √

ENA Mode and 1: ENA ON
F8.23
Fan control Decade: 0: Fan start working
1:Fan couldn’t work below 0 ℃

The proportional 0.00 0.10 √

F8.24 gain of ENA
0～100
frequency increases
F8.25 ENA Integration time 0.01～100 0.01 0.10 √

-71-
 Chapter 6 Detailed function description

6.1.10 F9 Group PID control

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
0：Keypad（set by F9.01）
1：Analog chanel AVI given
PID given 2：Analog chanel ACI given
F9.00 1 0 √
source selection 3：Remote communication given
4：Multi-step speed given
5:keyboard direct given

Keyboard preset
F9.01 0.0～F9.16 0.01MPa 0.00MPa √
PID given

0：Analog channel AVI feedback

PID feedback 1：Analog channel ACI feedback
F9.02 1 0 √
source selection 2：AVI+ACI feedback
3:Remote communication feedback

PID output
0：PID output is positive
F9.03 characteristics 1 0 √
1：PID output is negative
selection

Proportional gain K
F9.04 0.00～100.00 0.01 1.00 √
（Kp）

F9.05 Integral time Ti（Ti） 0.01～100.00s 0.1s 0.10s √

Differential time Td
F9.06 0.00～100.00s 0.1s 0.00s √
（Td）

Sample cycle T
F9.07 0.01～100.00s 0.1s 0.10s √
（T）

PID control
F9.08 0.0～100.0% 0.1% 0.0% √
bias limit

-72-
 Chapter 6 Detailed function description

6.1.10 F9 Group PID control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Feedback lost
F9.09 0.0～100.0% 0.1% 0.0% √
detecting value

Feedback lost
F9.10 0.0～3600.0s 0.1s 1.0s √
detecting time

F9.11 Feedback gain 0～200% 0.1% 100% √

Awakening threshold
F9.12 0.0～F9.16 0.01 MPa 0.50 MPa √
range

Awakening threshold
F9.13 0.00～360.00s 0.01s 1.00s √
detection time

0.00～F0.04
F9.14 Sleep Frequency 0.01 30.00Hz √
(Maximum output frequency)

Sleep Frequency
F9.15 0.0～360.00s 0.01S 1.00S √
Detection Time

F9.16 The gauge range 0.00-20.00MPa 0.01 MPa 20.00MPa √

PID preset 0.00～F0.05

F9.17 0.01Hz 0.00Hz √
frequency （Running frequency upper limit）

Preset frequency
F9.18 0.00～360.00s 0.01s 0.00s √
maintain time

-73-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

LED Unit’s Place ：PLC running

mode selection
0：invalid
1：single circulation
2：continuous circulation
3：single circulation keep the final
value .
LED Decade;PLC input selection
0：automatic control
1：Terminal Control
LED Hundreds place :
FA.00 PLC Mode PLC breakpoints recovery options 1 0000 √
0：Restart from the first stage
frequency.
1：Restart from running frequency .
which is saved before the sunning
is breaking .
2：Restart from setting frequency
when running is break.
PLC Thousands place:
PLC power failure save selection.
0：Non-save after power off
1：save after power off

FA.01 Multi-step speed 1 F0.06-F0.04 0.01Hz 0.00Hz √

FA.02 Multi-step speed 2 F0.06-F0.04 0.01Hz 0.00Hz √

FA.03 Multi-step speed 3 F0.06-F0.04 0.01Hz 0.00Hz √

FA.04 Multi-step speed 4 F0.06-F0.04 0.01Hz 0.00Hz √

-74-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

FA.05 Multi-step speed 5 F0.06-F0.04 0.01Hz 0.00Hz √

FA.06 Multi-step speed 6 F0.06-F0.04 0.01Hz 0.00Hz √

FA.07 Multi-step speed 7 F0.06-F0.04 0.01Hz 0.00Hz √

FA.08 Multi-step speed 8 F0.06-F0.04 0.01Hz 0.00Hz √

FA.09 Multi-step speed 9 F0.06-F0.04 0.01Hz 0.00Hz √

FA.10 Multi-step speed 10 F0.06-F0.04 0.01Hz 0.00Hz √

FA.11 Multi-step speed 11 F0.06-F0.04 0.01Hz 0.00Hz √

FA.12 Multi-step speed 12 F0.06-F0.04 0.01Hz 0.00Hz √

FA.13 Multi-step speed 13 F0.06-F0.04 0.01Hz 0.00Hz √

FA.14 Multi-step speed 14 F0.06-F0.04 0.01Hz 0.00Hz √

FA.15 Multi-step speed 15 F0.06-F0.04 0.01Hz 0.00Hz √

FA.16 Multi-step speed 16 F0.06-F0.04 0.01Hz 0.00Hz √

Unit of PLC 0:Second(s)

FA.17 1 0 √
Running time 1: Minute(min)

-75-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
0: Mode 1 :Linear Operation
FA.18 Curve selection 1: Mode 2( No wait time) 1 0 √
Gradual Operation

Multi-speed direction 0：External Control

FA.19 1 0 √
source selection 1: Control itself

PLC Accel/Decel
FA.20 0.01～3600.0s 0.1S 20.0S √
Time 1

PLC Accel/Decel
FA.21 0.1S 20.0S √
Time 2 0.01～3600.0s

PLC Accel/Decel
FA.22 0.1S 20.0S √
Time 3 0.01～3600.0s

PLC Accel/Decel
FA.23 0.01～3600.0s 0.1S 20.0S √
Time 4

PLC Accel/Decel
FA.24 0.01～3600.0s 0.1S 20.0S √
Time 5

PLC Accel/Decel
FA.25 0.01～3600.0s 0.1S 20.0S √
Time 6

PLC Accel/Decel
FA.26 0.01～3600.0s 0.1S 20.0S √
Time 7

PLC Accel/Decel
FA.27 0.01～3600.0s 0.1S 20.0S √
Time 8

Unit’s Place: Multi-Speed 1

FA.20-FA.27.
Decade : Multi-Speed 2
Acceleration FA.20-FA.27
FA.28 1 0x1111 √
Selection 1 Hundreds place: Multi-Speed 3
FA.20-FA.27
Thousands place：Multi-Speed 4
FA.20-FA.27

-76-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Unit’s Place : Multi-Speed 5

FA.20-FA.27
Decade : Multi-Speed 6
Acceleration FA.20-FA.27
FA.29 1 0x1111 √
Selection 2 Hundreds place : Multi-Speed 7
FA.20-FA.27
Thousands place ：Multi-Speed 8
FA.20-FA.27)

Unit’s Place : Multi-Speed 9

FA.20-FA.27
Decade: Multi-Speed10
Acceleration FA.20-FA.27
FA.30 1 0x1111 √
Selection 3 Hundreds place : Multi-Speed 11
FA.20-FA.27
Thousands place ：Multi-Speed 12
FA.20-FA.27

Unit’s Place : Multi-Speed 13

FA.20-FA.27
Decade: Multi-Speed 14
Acceleration FA.20-FA.27
FA.31 1 0x1111 √
Selection 4 Hundreds place : Multi-Speed 15
FA.20-FA.27
Thousands place ：Multi-Speed 16
FA.20-FA.27

Unit’s Place : Multi-Speed 1

FA.20-FA.27
Decade: Multi-Speed 2
Deceleration FA.20-FA.27
FA.32 1 0x1111 √
Selection 1 Hundreds place : Multi-Speed 3
FA.20-FA.27
Thousands place ：Multi-Speed4
FA.20-FA.27

-77-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Unit’s Place : Multi-Speed 5

FA.20-FA.27
Decade: Multi-Speed 6
Deceleration FA.20-FA.27
FA.33 1 0x1111 √
Selection 2 Hundreds place : Multi-Speed 7
FA.20-FA.27
Thousands place ：Multi-Speed 8
FA.20-FA.27

Unit’s Place : Multi-Speed 9

FA.20-FA.27
Decade: Multi-Speed 10
Deceleration FA.20-FA.27
FA.34 1 0x1111 √
Selection 3 Hundreds place : Multi-Speed 11
FA.20-FA.27
Thousands place ：Multi-Speed12
FA.20-FA.27

Unit’s Place : Multi-Speed 13

FA.20-FA.27
Decade: Multi-Speed 14
Deceleration FA.20-FA.27
FA.35 1 0x1111 √
Selection 4 Hundreds place : Multi-Speed 15
FA.20-FA.27
Thousands place ：Multi-Speed 16
FA.20-FA.27

Unit’s Place : Multi-Speed 1

(0-1) 0:Forward 1:Reverse
Decade: Multi-Speed 2
Direction (0-1) 0:Forward 1:Reverse
FA.36 1 0x0000 √
Selection 1 Hundreds place: Multi-Speed 3
(0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 4
(0-1) 0:Forward 1:Reverse

-78-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Unit’s Place : Multi-Speed 5

(0-1) 0:Forward 1:Reverse
Decade:: Multi-Speed 6
Direction (0-1) 0:Forward 1:Reverse
FA.37 1 0x0000 √
Selection 2 Hundreds place: Multi-Speed 7
(0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 8
(0-1) 0:Forward 1:Reverse

Unit’s Place : Multi-Speed 9

(0-1) 0:Forward 1:Reverse
Decade:: Multi-Speed 10
Direction (0-1) 0:Forward 1:Reverse
FA.38 1 0x0000 √
Selection 3 Hundreds place: Multi-Speed 11
(0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 12
(0-1) 0:Forward 1:Reverse

Unit’s Place : Multi-Speed 13

(0-1) 0:Forward 1:Reverse
Decade:: Multi-Speed 14
Direction (0-1) 0:Forward 1:Reverse
FA.39 1 0x0000 √
Selection 4 Hundreds place: Multi-Speed 15
(0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 16
(0-1) 0:Forward 1:Reverse

0.1S 0.0S
FA.40 PLC Running Time 1 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.41 PLC Running Time 2 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.42 PLC Running Time 3 0.0-6553.5 S(Min) √
(min) (Min)

-79-
 Chapter 6 Detailed function description

6.1.11 FA Multi- step speed control(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0.1S 0.0S
FA.43 PLC Running Time 4 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.44 PLC Running Time 5 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.45 PLC Running Time 6 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.46 PLC Running Time 7 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.47 PLC Running Time 8 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.48 PLC Running Time 9 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.49 PLC Running Time 10 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.50 PLC Running Time 11 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.51 PLC Running Time 12 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.52 PLC Running Time 13 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.53 PLC Running Time 14 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.54 PLC Running Time 15 0.0-6553.5 S(Min) √
(min) (Min)

0.1S 0.0S
FA.55 PLC Running Time 16 0.0-6553.5 S(Min) √
(min) (Min)

-80-
 Chapter 6 Detailed function description

6.1.12 Fb Protection function

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0：Disable.
1：normal motor
Motor overload
Fb.00 （with low speed compensation） 1 2 ×
protection
2：variable frequency motor
(without low speed compensation )

Motor overload 20.0～120.0%

Fb.01 protection current 0.1% 100.0% √
（Motor rated current）

Momentary power 70.0～110.0%

Fb.02 drop frequency point （Standard bus voltage ） 0.1% 80.0% √

Momentary power 0.00～F0.04

Fb.03 drop frequency
（Max.frequency） 0.01Hz 0.00Hz √
rate of decline

Over-voltage 0：Disable
Fb.04
stall protection
1 1 √
1：Enable

Over-voltage stall 110～150%（380V Series ）

Fb.05
protection voltage
1% 120% √
110～150%（220V Series ）

G Series:160%
Auto limiting
Fb.06 20～200% 1% √
current threshold
P Series:130%

Frequency decrease
Fb.07 rate when 0.00～100.00Hz/s 0.01Hz/s 10.00Hz/s √
current limiting
0：Invalid
Input phase loss Depends on
Fb.08
protection selection
1：software detect is valid 1 √
the model
2：hardware detect is valid
Under load
Fb.09
protection current
0-150.0 0.1% 0.0% √

Under load
Fb.10 5.0-6500.0 0.1S 5.0s √
protection Time

-81-
 Chapter 6 Detailed function description

6.1.13 Fc Group communication parameters

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

FC.00 Local address 1～247，0 is broadcast address 1 1 √

0：1200bps 3：9600bps
FC.01 aud rate selection 1：2400bps 4：19200bps 1 4 √
2：4800bps 5：38400bps

0：No parity（N，8，1）for RTU

1：Even parity（E，8，1）for RTU
2：Odd parity（O，8，1）for RTU
3：No parity（N，8，2）for RTU
4：Even parity（E，8，2）for RTU
5：Odd parity（O，8，2）for RTU
6：No parity（N，7，1）for ASCII
7：Even parity（E，7，1）for ASCII
Data bit 8：Odd parity（O，7，1）for ASCII
FC.02 1 1 √
check setting 9：No parity（N，7，2）for ASCII
10：Even parity（E，7，2）for ASCII
11：Odd parity（O，7，2）for ASCII
12：No parity（N，8，1）for ASCII
13：Even parity（E，8，1）for ASCII
14：Odd parity（O，8，1）for ASCII
15：No parity（N，8，2）for ASCII
16：Even parity（E，8，2）for ASCII
17：Odd parity（O，8，2）for ASCII

Communication
FC.03 0～200ms 1ms 5ms √
answer delay time

Communication
FC.04 0.0（Odd parity），0.1～200.0s 0.1s 0.0s √
timeout fault time

-82-
 Chapter 6 Detailed function description

6.1.13 Fc Group communication parameters(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

0：Alarm and coast to stop

1：Do not alarm and keep running
2：Do not alarm and stop at the
Communication stopping method( only for
FC.05 1 1 √
error action communication control mode )
3：Do not alarm and stop at the
stopping method (for all
communication control modes )

0：Response to reading and writing

FC.06 Response action 1 0 √
1：No response to writing

Communication
0：group mode
FC.07 parameters 1 0 √
1：Sequential mode
address mode

Linkage proportion
FC.08 0.01～10.00 0.01 1.00 √
coefficient

0：Keypad or Encoder Setting

（FC.08）
1：Annlog AVI setting
Linkage proportion
FC.09 2：Annlog ACI setting 1 0 √
source selection
3：Multi-stage setting
4：Keyboard or encoder direct
setting

-83-
 Chapter 6 Detailed function description

6.1.14 Fd Group Supplementary function

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation
Low-frequency
Fd.00 threshold of 0～500 1 5 √
restraining oscillation
High-frequency
Fd.01 threshold of 0～500 1 5 √
restraining oscillation

Amplitude of
Fd.02 0～100 1 10 √
restraining oscillation

Threshold high-low
Fd.03 frequency of 0.00～F0.04（Max.frequency ） 0.01Hz 12.50Hz √
restraining oscillation

0：Enable
Fd.04 Restrain oscillation 1 1 √
1：Diable

0：PWM mode 1
Fd.05 PWM Selection 1：PWM mode 2 1 0 ×
2：PWM mode 3

0：Keypad setting torque

(corresponding to Fd.07)
1：1: Analog AVI setting torque
(100% compared to 2 times of
inverter rated current)
2：2: Analog ACI setting torque
Torque setting
Fd.06 (same as 1) 1 0 √
mode selection
3：3: Analog AVI + ACI setting
torque ( same）
4：multi-stage torque setting
( same 1)
5：Remote communication
setting torque .(same as 1)

-84-
 Chapter 6 Detailed function description

6.1.14 Fd Group Supplementary function(continued )

Runn
Factory ing
Code Name Factory setting Min.Unit
setting Modifi
cation

Keypad torque -200.0～200.0%

Fd.07 0.1% 50.0% √
setting （the rated current of inverter）

0：Keypad setting upper limit

frequency（F0.05）
1：Analog AVI setting upper limit
frequency (100% corresponds to
Upper limit
the maximum frequency)
frequency
Fd.08 2：Analog ACI setting upper limit 1 0 √
source
frequency (same as 1）
selection
3：Multi-step setting of upper limit
frequency(same as 1)
4：Remote communication setting
upper limit frequency (same as1)

Auto current 0：Enabled when constant speed

Fd.09 1 0 √
limiting selection 1：Disabled when constant speed

Lower limit 0：lower limit frequency running

Fd.10 frequency 1：zero frequency running and 1 0 ×
running mode DC braking .

Zero-frequency
Fd.11 running braking 0.0～150.0% 0.1% 0.0% √
current

-85-
 Chapter 6 Detailed function description

6.2 Detailed function description

F0 Group-Basic function
F0.00 Speed control mode
Setting Range: 0～3 Factory setting : 1

This function is used to select the control mode of the inverter.

0: NO PG vector control
Sensorless vector control(SVC).It means open-loop vector contro, applied to occasions
without PG,high-performance general-purpose , an inverter can drive a motor .
1: V/F Control
It’s suitable for the application with low accuracy control ,low frequency torque .
an inverter can drive multi motors .
2: Torque control
It is suitable for the pplication with low accruracy torque control .Sunch as wired
-drawing ect .the speed of motor is determined by the load .the speed of ACC/DEC
has nothing to do with the ACC/DEC time .
3: PG Vector Control
The inverter have speed sensor vector control (VC). Suitable for high-performance
adjusting the speed occasion with installing encoder PG , one inverter can only drive
one motor.

When F0.01=0 is selected . the motor parameters have to be auto-tuning before first
running . In order to get the correct motor parameters . Please make sure the lable of
the motor match with the motor parameters of the inverter .Otherwise it will result-in
auto-tuning couldn’t accomplish or get the wrong results . When it couldn’t get the
parameters/lable of the motor.It is suggested the user use V/F control.
When F0.0=1 is selected . Should set the related parameters (F3 Group). To assure
the excellent steady dynamic performance.
Inverter can drive only one motor when F0.00 is set to 0. and the inverter and the
capacity class of the motor couldn’t be big . Otherwise it will result in the control
performance reduce or couldn’t work normally .

-86-
 Chapter 6 Detailed function description

F0.01 Run command channel

Setting Range:0～2 Factory setting: 0

This function is used to set the inverter receive the control mode which forward,
reverse, jog and stop ect control command.
0: Keyboad command channel
To control the inverter start and stop by the key RUN、STOP、REV/JOG On the
keypad.
1: Terminal command channel
To control the inverter start and stop by external control terminal Xn—COM on
and off .
2: Communication command channel
To control the inverter start and stop by RS485 serial port.

F0.02 Keyboard and terminal UP/Down setting

Setting range:0～3 Factory setting : 0

The frequency can be set by ▲/▼ or encoder on the keypad and terminal
UP/DOWN.This setting method have the highest and it can be combined with setting
channel .It is used to adjust the output frequency during the commission of the control
system .
0：Valid , save the parameters when the inverter is power off .
The frequency command can be set and the value can be saved after the inverter is
powered off and it will combinate with the current frequency when it is repowered on .
1：Valid ,the value can not be saved when the inverter is powered off.
The frequency command can be set but the value can not be saved after the inverter
is powered off .

-87-
 Chapter 6 Detailed function description

2：UP/DOWN setting is valid .

3：valid during running ,the frequency setting value will be clear automatically when
the inverter stops .

When the factory setting is restored ,the value of

keypad and UP/DOWN will be cleared .

F0.03 Frequency command selection

Setting range :0～12 Factory setting : 0

This function is used to select the frequency command channel of inverter .

0：Keypad or encoder setting
Modify the value of F0.07 to set the running frequency by the keypad.
And can change the running frequency by the key or encoder on the keypad
and terminal UP/DOWN when the inverter is running . The revised frequency value
can saved to F0.07 after power off . If you want the frequency can not saved. Upi am
set the parameter F0.02.
1： AVI analog setting
The running frequency can be set by the external voltage input terminal AVI.
Please refer to F5.11～F5.15。
2：ACI analog setting
The running frequency can be set by the external current or voltage input terminal
ACI.Please refer to F5.16～F5.20。
3：AVI*ACI
Two group analog participate in arithmetic:AVI(the upper limit corresponding
frequency)*ACI(he upper limit corresponding coefficient).
4：Potentiometer
This parameter is valid when the keypad with potentiometer.
-88-
 Chapter 6 Detailed function description

5: PID control setting 12.Common PID control setting

The inverter mode is PID control when this parameter is selected .It’s necessary
to set F9 group “PID control group”. The inverter running frequency is the frequency
value after PIF control . and PID given source, Feedback source and so on, Please
refer to F9 Group “PID function” introduction .
6: Remote communication setting
The running frequency is set by RS485 communication port .
7: External pulse setting
The running frequency is set by terminal X8 input pulse signal .For more details .
Please refer to F5.21~F5.25。
8: AVI(host )±ACI(assit )setting
9: Keyboard(host) ±ACI(assit )setting
10: Communication (host) ±ACI(assit )setting
AVI 、keyboard 、commicanition are the main frequency input . linear plus the
main frequency when the analog ACI is the centre value and above, linear minus the
main frequency when the analog ACI is the centre value and below . when the main
frequency is o .and the output frequency is 0.
11: Combination Setting
The running frequency is set by combination. The combination mode confirmed
by F0.15-F0.16.

When the frequency given mode is selected to

7.should to use terminal X8.Other terminal is invalid.

F0.04 Maximum output frequency .

Setting Range:10.00～600.00Hz Factory Setting:50.00 Hz

-89-
 Chapter 6 Detailed function description

Set the maximum output frequency of inverter .It’s thefoundation of frequency

settings .and also the basis of speed acceleration and deceleration .Please pay
attention to it.

F0.05 Upper limit frequency

Setting range:F0.06～F0.04 Factory Setting :50.00Hz
F0.06 Lower limit frequency
Setting range:0.00～F0.05 Factory Setting:0.00Hz

The upper frequency limit is the inverter allowable working the maximum output
frequency . The value should not exceed the the maximum output frequency.
The lower frequency limit is the inverter allowable working the minimum output
frequency . The lower limiting frequency is working when the setting frequency is lower
than the lower frequency limit .
The value should not exceed the the maximum output frequency.
the maximum output frequency≥the upper frequency limit≥the lower frequency
limit .

F0.07 keypad setting frequency

Setting range:0.00Hz～F0.04 Factory setting :50.00Hz

When the frequency setting mode F0.03=0 is selected . the parameter is the
initial value of inverter setting frequency .

F0.08 Acceleration time 1

Setting range:0.1～3600.0s Factory setting: Depend on the model
F0.09 Deceleration time 1
Setting range:0.1～3600.0s Factory setting: Depend on the model

-90-
 Chapter 6 Detailed function description

The acceleration time is the time of accelerating from 0Hz to Maximum frequency.
The deceleration time is the time of decelerating from maximum frequency to
0Hz. Please refer to the Figure6-1.

Figure 6-1 Acceleration and deceleration time

F0.10 Running direction selection

Setting range:0～2 Factory setting: 0

To change the running direction of the motor.

0：Forward(the default running direction)
1：Reverse
2：Forbid reverse

F0.11 Carrier frequency

Setting range:1.0～15.0kHz Factory setting: Depend on the model

This function is used to set the carrier frequency of the inverter output PWM wave.
shoud adjust correctly . the maximum value of the carrier frequency depend on power.
the value of carrier frequency and electromagnetic noise,leakage current and heat
dissipation as shown in Figure6-2.

-91-
 Chapter 6 Detailed function description

Setting Range of
220V Series 380V Series Carrier Frequency

0.4-3.7kW 0.75-7.5kW 1.0-15.0kHz

Figure 6-2 Carrier frequency

The advantage of high carrier frequency : ideal current

waveform ,little current harmonic wave and motor noise .
 he disadvantage of high carrier frequency L increasing
T
the switch loss .inceasing the inverter termperature and
the impact to the output catacity .the inverter needs to
derate on high carrier frequency .at the time ,the leakage
and electrical magnetic interference will increase .
 pplying low carrtier frequency is contrary to the above.
A
too low carrier frequency will cause unstable running ,
torque decreasing and surge.

F0.12 Motor parameters autotuning

Setting range:0～2 Factory setting: 0

0：No action : Forbidding autotuning .

-92-
 Chapter 6 Detailed function description

1：Rotation autotuning
Do not coonect any load to the motor when performing autotuning and ensure
the motor is in static state. Input the nameplate parameters of motor (（F2.01～F2.05）)
correctly before performing autotuning . Otherwise the parameter detected by
autotuning will be incorrect .
Set the proper acceleration and deceleration time （F0.08、F0.09）according
to the motor inertia before performing autotuning . Otherwise it may cause over-current
and over-voltage fault during autotuning .
Set F0.12 to 1 then press ENTER to start the autotuning . the LED will display
and flicker .Press RUN to start the autotuning . LED will display TUN0. And the motor
begin to run after displaying TUN1.When the parameter autotuning is finished and will
dipaly “ END ”.Finally return to the stop state . when “ TUN ” is flicker,you can
press MODE to exit out the autotuning status .
You can press STOP/RESETto stop the parameter autotuning operation during
autotuning .
2：Static autotuning
If it is difficult to disconnect the load .static autotuning is recommended . enter
the correct motor nameplate parameters of motor (（F2.01～F2.05）) correctly before
performing autotuning.the resistance of stator and rotor and leakage inductance of
motor will be tested after autotunign . But mutual inductance and current without load
will not be able to measure .users can input the corresponding value according to your
experience .

This parameters is valid when vector control F0.00=0 and the

keypad control running mode F0.01=0.are selected

-93-
 Chapter 6 Detailed function description

F0.13 Restore parameters

Setting range: 0～5 Factory setting: 0

0：No action
1：Restore the default value
Restore all parameters F0～Fd to factory setting except F2 group.
2：Clear fault records
Inverter clear all fault records.
3：Restore the default value to 380V/60Hz.
4：Restore the default value to 440V/50Hz.
5：Restore the default value to 440V/60Hz.

F0.14 AVR Fcuntion

Setting range: 0～2 Factory setting : 0

0：Disable
1：Enable all the time
2：Disabled during deceleration
AVR( Auto voltage regulation) function is to adjust PWM to stable the output of
inverter when the input voltage and rated input voltage have deviation .
This function is disable when the output command voltage is bigger than input
power voltage . If AVR is function is disable ,the deceleration time will be short but the
current will be big . if AVR is enable all the time .the motor working stable .the
deceleration time will be long but the current will be small .

F0.15 Combination channel setting

Setting range: -000～ -777 Factory Setting: 0

The parameter is used to setting the frequency given chanel .

LED Unit’s Place: Operand 1
0:Keypad Potentiometer 4:AVI
1:Keypad or Encoder 5:ACI
2.Reseve 6: External Pulse Setting
3:Communication 7: Multi-speed stage
-94-
 Chapter 6 Detailed function description

LED Decade: Operand 2

0:Keypad Potentiometer 4:AVI
1:Keypad or Encoder 5:ACI
2:Reseve 6: External Pulse Setting
3:Communication 7: Multi-speed stage
LED Hundreds place: Operand 3
0:Keypad Potentiometer 4:AVI
1:Keypad or Encoder 5:ACI
2:Reseve 6: External Pulse Setting
3:Communication 7: Multi-speed stage
Thousands place： Reserved

F0.16 Combination algorithm Setting

Range:00～54 Factory Setting : 00

The parameter is used to set the combination frequency given algorithm.

LED unit's place digit: Algorithm 1
0. Addition
1. Subtraction
2. Absolute value (subtraction)
3. Take the maximum value
4. Take the minimum value
LED decade digit: Algorithm 2
0. Addition
1. Subtraction
2. Absolute value (subtraction)
3. Take the maximum value
4. Take the minimum value
5. Operand 3 does not participate in algorithm

-95-
 Chapter 6 Detailed function description

LED Hundreds 、Thousands place： Reserved.

F0.15、F0.16 will be valid only when F0.03=11 ，The Parameter’s algorithm
formula is shown below:(Operand 1) Algorithm 1 (Operand 2) Algorithm 2 (Operand 3)
If the decade digit of F0.16 is set to 5, the operand 3 will anticipate in algorithm
composed of two figures (Operand 1 and Operand 2).
Eg.1 If F0.15=534 and F0.16=10, then the algorithm pairs will be:
｜(AVI + Communication) -ACI｜
Eg 2: F0.15=460, F0.16=21 then the algorithm pairs will be:
｜(Keyboard-terminal pulse setting)-AVI｜

Algorithm rule 1: In any case, the algorithm procedure is

always like this: operation figure 1 and operation figure 2
participate in algorithm 1 and get the result 1, then put
result 1 and operation figure 3 into algorithm 2 and get
the final result. If the algorithm result of previous two
figures is a negative number,then the default result of the
system will be "0".
 lgorithm rule 2: If the general algorithm result is a negative
A
number and algorithm 2 is not an absolute one, then the
default result of the system will be "0".

F0.17 Parameter locked

Setting Range :0～1 Factory Setting : 0

The parameter is used to modify permission for setting paramters . Specific set
as follows:
0: All parameters are allowed to be rewritten, but some parameters can not be
modified when the inverter is running .

-96-
 Chapter 6 Detailed function description

1: In addition to the digital frequency setting and this parameter,other parameters

prohibited rewritten.

F0.18 Acceleration and deceleration mode selection

Setting Range :0～1 Factory Setting: 0

0：Linear Accel/Decel.
The Output frequency increase or decreases with a constant rate .
1：S-Curve Accel/Decel
To reduce the noise and vibration of the mechanical system,It can slowly change
the output frequency at the initial and ending segments of Accel/Decel.as shown in
Fig.6-3.

Frequency

S curve

Linear.

Time
F0.19 F0.20 F0.20 F0.19

Fig.6-3 Accel/Decel Curve.

F0.19 Temperature alarm switch

Setting Range:0-1 Factory Setting:0

0: Invalid 1: Valid

F0.20 Alarm temperature value

Initiate an alarm when the detected value is greater than F0.19

-97-
 Chapter 6 Detailed function description

F1 Group- Start and stop control

F1.00 Start Mode

Setting range: 0～2 Factory setting: 0

0：Start directly
Start the motor at the starting frequency determined by F1.01.
1：DC braking and start
DC braking at first (Refer to the parameters F1.03 and F1.04).then start the motor
at the starting frequency .It is sutiable for the motor which have small inertia load and
may reverse rotation when start .
2：Speed tracking starting
Can track the rotation and direction of the the motor . Then starting at the tracking
speed . running to the setting frequency by acceleration and deceleration time .

F1.01 Direct starting frequency

Setting range:0.00～50.00Hz Factory setting:1.50Hz
F1.02 Starting frequency maintain time
Setting range:0.0～50.0s Factory setting:0.0s

The inverter will start at the starting frequency ,As shown in Figure 6-4.In order
to ensure enough starting torque .you should set the reasonable starting frequency .
The starting frequency maintain time indicate the starting frequency maintain
time when the inverter start . As show in Figure 6-4.

-98-
 Chapter 6 Detailed function description

Figure 6-4 Start and stop frequency output curve

F1.03 DC braking current before start.

Setting range:0.0～150.0% Factory setting:0.0 %
F1.04 DC braking time before start
Setting range:0.0～50.0s Factory setting:0.0s

DC braking current before start: The inverter start at DC starting . the braking
current percentage .
DC braking time before start: the output DC braking current duration time during
the inverter starts . this function is invalid when the DC braking time is 0.0s.

DC braking current and braking time should be

consider the load . the current couldn’t be too
high .Otherwise the current will trip .It’s no
suitable to use the DC braking mode and
F1.00=1 is valid.

-99-
 Chapter 6 Detailed function description

F1.05 Stop mode

Setting range :0～1 Factory setting: 0

0：Ramp to stop
When the stop command takes affect. The inverter decreases the output
frequency according to the selected acceleration/deceleration time till stop.
1：Coast/Free stop
When the stop command takes affect,the inverter blocks the output immediately.
the motor coasts to stop by its mechanical inertia .
2：Deceleration stop +Free stop

F1.06 Starting frequency of DC braking at stopping

Setting range:0.00～F0.04 Factory setting:0.00Hz
F1.07 Braking wait time at stopping
Setting range: 0.0～50.0s Factory setting:0.0s
F1.08 DC braking current at stopping
Setting range: 0.0～150.0% Factory setting:0.0%
F1.09 DC braking time at stopping
Setting range: 0.0～50.0s Factory setting:0.0s

F1.06 The frequency of DC braking starting when the inverter is decelerating

to stop .
F1.07 The inverter close output for an interval and then braking befor DC
braking .
F1.08 The percentage of rated current of inverter. The bigger the DC braking
current .the greater the braking torque .
F1.09 The maintain time for DC braking at stopping .

-100-
 Chapter 6 Detailed function description

The current of DC braking at stopping set too

high .The inverter is easy to trip . Please set the
current from small to bigger .
There is no DC braking when the DC braking
time at stopping set to 0.0S.

F1.10 Dead time of FWD/REV

Setting range:0.0～3600.0s Factory setting:0.0s

Set the interval time at 0.0Hz in the transition between forward and reverse .It is
shown as following figure 6-5.

Fig 6-5 FWD/REV dead time

F1.11 Terminal running protection selection when poweron

Setting range:0～1 Factory setting: 0

In the terminal command mode , when the inverter powered on. The system will
automatically detect the status of terminal .

-101-
 Chapter 6 Detailed function description

0：Command invalid when powered on .

Although detected effective commandof terminal in process of powered on . the
inverter will not run .the system is running is the protection state until withdrawal of the
terminal operation command .and then enable the terminal.inverter will run .
1：Command valid when powered on
That is to say when the inverter is in the process of powered on . If detected the
effective operation the command of terminal . waiting for the complection of initialization.
the system will automatically start the inverter .

The user select this function with caruton .

Otherwise may lead to serious consequences .

F1.12 Input/Output terminal selection

Setting range:0x000～0x7FF Factory setting :0x000

This function code defines the positive and negative logic of terminals.
Positive logic 0: Valid when connecting SI with corresponding common
terminal and invalid when dis connecting these terminal .
Negative logic 1: Invalid when connecting SI with corresponding common
terminal and valid when disconnecting these terminals.
If you request X1~X4 is positive logic, X5～X8 is negative logic ,Y1,Y2
is positive logic,RY is negative logic . The setting are as follows :
The logic state of X4-X1 is 0000,and the corresponding hex is 0. The unit
digit of LED is displayed to 0. the logic state of X8-X5 is 1111. and the corresponding
hex is F. the logic state of RY ,Y1,Y2 is 100. and the corresponding hex is 4. The
tens digit of LED is The function code of F1.12 is 4F0.As shown in Figure 6-6.

-102-
 Chapter 6 Detailed function description

Hundred’s place Decade Place Unit’s place

0 0 0 0 0 0 0 0 0 0 0
X 8 X7
R Y Y 2 Y 1 X8 X 7 X 6 X5 X4
X 4 X3 X2 X1
Figure 6-6 Terminal slection setting diagram

F1.13 Power off Restart Mode Selection

Setting range:1-3 Factory setting 0

F1.14 Power Cut Restart Wait Time

Setting range: 0.0-20.0S Factory setting : 0.5S

F2 Group- Motor parameters

F2.00 Inverter Type

Setting range:0～1 Factory setting: 0

0：G Type
Applicable to constant torque load
1：P Type
Applicable to variable torque load (i.e. fans pumps).

The users can set this group parameters to change

the inverter type . To realize G/P integration function.
It only has G model for 220V inverter .

F2.01 Motor rated power

Settig range:0.4～700.kW Factory setting: depend on model

-103-
 Chapter 6 Detailed function description

F2.02 Motor rated frequency

Settig range:0.01-600.00Hz Factory setting:50.00Hz
F2.03 Motor rated speed
Settig range :0～36000rpm Factory setting: depend on model
F2.04 Motor rated voltage
Settig range:0～460V Factory setting: depend on model
F2.05 Motor rated current
Settig range:0.1～2000.0A Factory setting: depend on model

In order to achieve superior performance .Please set these parameters according

to motor nameplate .and then perform auto-tuning .
The power performance of inverter should match the motor .If the bias is too big.
The control performances of inverter will be deteriorated distinctly .

Reset the motor rated power(F2.01) can initialize

F2.06～F2.10 automatically .

F2.06 Motor stator resistance

Setting range:0.001～65.535Ω Factory setting: depend on model
F2.07 Motor rotor resistance
Setting range :0.001～65.535Ω Factory setting: depend on model
F2.08 Motor leackage inductance
Setting range :0.01～655.35mH Factory setting: depend on model
F2.09 Motor mutual inductace
Setting range :0.01～655.35mH Factory setting: depend on model

-104-
 Chapter 6 Detailed function description

F2.10 Current without load

Setting range :0.01～655.35A Factory setting: depend on model

The above parameters is the necessary parameters for vector control .

The value of F2.06~F2.10 will be sutomatically updated after auto tuning .

Do not change these parameters arbitrarily .otherwise it may deteriotate the

control performance of inverter .

F3 Group-Vector control
F3.00 proportional gain 1 of speed loop
Setting range:0～10000 Factory setting:15
F3.01 Integration time 1 of speed loop
Setting range:0.01～100.00s Factory setting:2.00s
F3.02 Low switching point frequency
Setting range:0.00～F3.05 Factory setting:5.00Hz
F3.03 proportional gain 2 of speed loop
Setting range:0～10000 Factory setting:10
F3.04 Integration time 2 of speed loop
Setting range:0.01～100.00s Factory setting:3.00s
F3.05 High switching point frequency
Setting range:F3.02～F0.04 Factory setting:15.00Hz

The above parameter are only valid for vector control mode . invalid in V/F
control mode .If the frequency is leass than low swithching point frequency (F3.02).
we can adopt PI parameter F3.00 and F3.01.If the frequency is more than high
switching point frequency 2(F3.05).we can adopt PI parameter F3.00 and F3.04.
The PI parameters will be get from the linear change of the two group parameters.
As shown in Figure 6-7.

-105-
 Chapter 6 Detailed function description

By setting the ratio the speed regulator factors and integration time .you can
adjust the speed of dynamic response characteristics of vector control .Increase
the proportional gain .reducing the integtation time can speed up the daynamics
of the corresponding ring .But the proportional gain is too large or too small
intergtation time are easily lead to system oscillation .overshoot is too large .
Proportional gain is too small can easily cause the system to steady-state oscillation .
and the speed of static difference may exist .
PI speed loop parameters and the inertia motor system are closely related .

Figure 6-7 PI parameter diagram

F3.06 Slip compensation rate of VC

Setting range:50～200% Factory setting:100%

The parameter is used to adjust the slip frequency of vector control and improve the
accuracy of speed control .Properly adjust this parameter can effectively restrain the
stativ speed bias .

F3.07 Torque upper-limit setting

Setting range:0.0～200.0% Factory setting:150%

Set 100% correspomds to the rated output current of the inverter .

-106-
 Chapter 6 Detailed function description

F3.08 Torque dynamic friction coefficient

Setting range:0.000～1.000 Factory setting:0.125
F3.09 Empty load current compensation coefficients
Setting range:0.000～9.999 Factory setting:0.800
F3.10 Torque static friction coefficient
Setting range:0.00-10.00 Factory setting:2.00

Torque dynamic friction coefficient is used to adjust the operation of the motor
torque value;
Torque static friction coefficient is used to adjust the torque value of the motor
not in operation.

F4 V/F Control Group

F4.00 V/F Curve setting
Setting range::0～6 Factory setting: 0

This group parameter is valid when the inverter in V/F mode(F0.00=1).

0: Linear Curve .It is applicable for normal constant torque load .
1:Square V/F curve . It is applicable for variable torque load .such as blower ,
pump and so on .Please refer to following figure 6-8 .

Figure 6-8 V/F curve

-107-
 Chapter 6 Detailed function description

2:User-defined Setting V/F Curve

When delecting this mode .just set the expected V/F curve through F4.06-F4.11.
As shown in Fig.6-10.
3.1.25 Power V/F Curve
4.1.7 power V/F Curve
5. 3 power V/F Curve
6. 4 power V/F Curve
Peameters values 3-6 aply to torque-dropped loadsp such as fans and water
pumps.See Fig.6-9

Output voltage(V)

Rated voltage of motor

1.7 power

2.0 power
1.0 power

3.0 power

4.0 power

Output frequency(Hz)
Rated frequency of motor

Figure 6-9 V/F curve

F4.01 Torque Boost

Setting range: 0.0～30.0% Factory setting: 2%

-108-
 Chapter 6 Detailed function description

F4.02 Torque boost cutoff

Setting range : 0.0～50.0% Factory setting : 20%

Torque boost will take effect when output frequency is less than cut-off frequency
of torque boost (F4.02).The boosting V/F curve as shown in 6-9(1).Torque boost can
improve the torque performance of V/F control at low speed . when the torque boost
setting is 0.0% , the inverter will boost the output torque accoding to the load automatically .
Torque boost cutoff:The torque boost is effective below this frequency point .
and the torque boost is invalid higher than this frequency point .

Figure 6-9(1) Manual torque boost diagram

If the torque boost too high . It will appear the inverter over
current protection . and will lead to the motor couldn’t
start normally . At this time It is reasonable to lower setting
value .

-109-
 Chapter 6 Detailed function description

If the torque boost too high . It will appear the inverter over
current protection . and will lead to the motor couldn’t
start normally . At this time It is reasonable toIf the motor
working at low frequency for long time .The heat dissipation
will become bad .At this time .if the torque boosting value
set too high and Intensified this phenomenon. Finally
the motor may burnt. Make sure take the motor external
forced cooling mode or derating. Keep in mind !

F4.03 V/F Slip compensation limit

Setting range : 0.0～100.0% Factory setting : 0.0%

The motor’s slip changes with the load torque .which resulit in variance of motor
speed .the inverter’soutput frequency can be adjusted automatically through slip
compensation according to the load torque , Therefore the change of speed due to
the load change can be reduced ,the value of compensated slip is dependent on the
motor’s rated slip which can be calculated as F4.03=(fb-n*p/60)/ fb.
Where fb is motor rated frequency (F2.02), n is motor rated speed (F2.03) and
P is poles pairs of motor .

F4.04 Auto energy saving selection

Setting range: 0～1 Factory setting : 0

When F4.04 is set to be 1. Where there is light load .It will reduce the inverter
output voltage and saves energy .
0：Disable
1：Enabled

-110-
 Chapter 6 Detailed function description

This function is applicable for fan and pump and other

load.
Auto energy saving running is invliad during acceleration
and deceleration running .

F4.05 Reserved

F4.06 V/F Frequency Value F1

Setting range: 0.00～F4.08 Factory setting: 12.50Hz
F4.07 V/F Voltage Value V1
Setting range: 0.00～F4.09 Factory setting:25.00%
F4.08 V/F Frequency Value F2
Setting range: F4.06～F4.10 Factory setting:25.00Hz
F4.09 V/F Voltage Value V2
Setting range: F4.07～F4.11 Factory setting:50%
F4.10 V/F Frequency Value F3
Setting range: F4.08～F0.05 Factory setting:37.50Hz
F4.11 V/F Voltage Value V3
Setting range: F4.09～100.00% Factory setting:75.00%

The parameters are used to set the user needs flexible V / F curve. As shown in
Figure 6-10 Voltage

F4.11

F4.09
F4.07
Frequency

F4.06 F4.08 F4.10

Fig.6-10 V/F User-defined Curve Setting

-111-
 Chapter 6 Detailed function description

F4.12 Low voltage protection selection

Setting range :0-1 Factory setting:0

0：Enabled
1：Disable

F5 Group-Input terminals

F5.00 X1 input terminal selection

Setting range:0～34 Factory setting: 1
F5.01 X2 input terminal selection
Setting range:0～34 Factory setting: 2
F5.02 X3 input terminal selection
Setting range:0～34 Factory setting: 7
F5.03 X4 input terminal selection
Setting range:0～34 Factory setting: 0
F5.04 X5 input terminal selection
Setting range:0～34 Factory setting: 0
F5.05 X6 input terminal selection
Setting range:0～34 Factory setting: 0
F5.06 X7 input terminal selection
Setting range:0～34 Factory setting: 0
F5.07 X8 input terminal selection
Setting range:0～34 Factory setting: 0

External input terminal X1~X8 are Multi-function input terminal . you can select
the function X1~X8 by setting the value F5.00-F5.07. The specific setting value and
description are as follows:

-112-
 Chapter 6 Detailed function description

0：No function
1：Forward running
2: Reverse running
The inverter running command is given by the above terminal when the running
command channel is terminal control .
3：3-Wire control
Please refer to the description of P5.09.
4：Jog forward control
5: Jog reverse control
Frequency acceleration and deceleration of jog running .Please refer to description
of F8.02~8.04.
6： Coast to stop
The inverter blocks the output immediately .the motor coasts to stop by its
mechanical inertia .
7：Reset fault
Fault resets through terminal when the inverter is fault alarming . the function is
same to the STOP key on your keyboard .
8：External fault input
When an external fault signal sent to the inverter ,the inverter alarm external
fault(EF) and stop .
9：Frequency up command
10: Frequency DOWN command
11: Clear frequency UP/DOWN
The above three function to use the external terminal to modify the given
frequency . UP is the increment command .DOWN is the decrement command .

-113-
 Chapter 6 Detailed function description

Frequency UP/DOWN clearance is to clear the setting value through UP/DOWN .the
given frequency to return to a given frequency by the frequency command channel.
12：Multi-step speed terminal 1
13: Multi-step speed terminal 2
14: Multi-step speed terminal 3
15: Multi-step speed terminal 4
16 steps speed control can be realized by the combination of these four terminal .
The external terminals of the implementation of speed control must comply with the
running command can run. The speed of the terminal control the step speed .as
shown in Table 6-1.

Table 6-1 Multi-step speed selection

Multi-step Multi-step Multi-step Multi-step

Multi-step speed
speed speed speed speed
selection
terminal 4 terminal 3 terminal 2 terminal1

1st step of multi-step

OFF OFF OFF OFF speed.The running
frequency set by FA.01.

2nd step of multi-step

OFF OFF OFF ON speed.The running
frequency set by FA.02.

3rd step of multi-step

OFF OFF ON OFF speed.The running
frequency set by FA.03.

-114-
 Chapter 6 Detailed function description

Table 6-1 Multi-step speed selection

Multi-step Multi-step Multi-step Multi-step

Multi-step speed
speed speed speed speed
selection
terminal 4 terminal 3 terminal 2 terminal1

4th step of multi-step

OFF OFF ON ON speed.The running
frequency set by FA.04.

5th step of multi-step

OFF ON OFF OFF speed.The running
frequency set by FA.05.

6th step of multi-step

OFF ON OFF ON speed.The running
frequency set by FA.06.

7th step of multi-step

OFF ON ON OFF speed.The running
frequency set by FA.07.

8th step of multi-step

OFF ON ON ON speed.The running
frequency set by FA.08.

9th step of multi-step

ON OFF OFF OFF speed.The running
frequency set by FA.09.

-115-
 Chapter 6 Detailed function description

Table 6-1 Multi-step speed selection

Multi-step Multi-step Multi-step Multi-step

Multi-step speed
speed speed speed speed
selection
terminal 4 terminal 3 terminal 2 terminal1

10th step of multi-step

ON OFF OFF ON speed.The running
frequency set by FA.10.

11th step of multi-step

ON OFF ON OFF speed.The running
frequency set by FA.11.

12th step of multi-step

ON OFF ON ON speed.The running
frequency set by FA.12.

13th step of multi-step

ON ON OFF OFF speed.The running
frequency set by FA.13.

14th step of multi-step

ON ON OFF ON speed.The running
frequency set by FA.14.

15th step of multi-step

ON ON ON OFF speed.The running
frequency set by FA.15.

-116-
 Chapter 6 Detailed function description

Table 6-1 Multi-step speed selection

Multi-step Multi-step Multi-step Multi-step

Multi-step speed
speed speed speed speed
selection
terminal 4 terminal 3 terminal 2 terminal1

16 th step of multi-step
ON ON ON ON speed.The running
frequency set by FA.16.

Note: ON stand for COM port connection . OFF stand for COM port disconnect .
16：Acceleration and deceleration time selection
Select two kinds of acc.and dec. time through the combinations of the number
of this two terminals.
Table 6-2 Acceleration and deceleration time selection

Accel.and decal.
Acceleration and deceleration time
time selection

OFF Acceleration and deceleration time 1

ON Acceleration and deceleration time 2

17：PID control pause

The inverter will keep the current frequency output unchanged when PID is invalid .
18：Traverse frequency pause
Inverter keeps output frequency unchanged .If this terminal is disable. Inverter
will continue traverse frequency operation from the current frequency.
19：Traverse frequency reset
The setting frequency of the inverter will return to the centre frequency .

-117-
 Chapter 6 Detailed function description

20：Acceleration and deceleration prohibition

Ensure the inverter keeo away from the external signal (except the stopping
command) and maintain the current output frequency .
21：Disable torque control
The inverter will work shifting from torque control to speed control mode .
22：Clear frequency acc.and dec. settings
When the terminal closed. The frequency set by UP/DOWN can be cleared.
Frequency returns to the frequency given by command chanel . After the terminal
discoonect the frequency returns to the value which is set by UP/Down settings.
23：DC braking when stopping
During the process of decelerating to stop .when this terminal is on ,the inverter
will be in the state of DC braking promptly .Braking state is determined by F1.07~F1.09.
24：External pulse input
For receiving an external pulse signal as the frequency giving (only X8 multi-
function terminal can set this feature).
25：Frequency switch to ACI
26:Frequency switch to AVI
The frequency command forced to switch to ACI (AVI) when the terminal closed .
and will restor the previous given mode when the terminal disconnected .
27：Reseved
28：Coast to stop control
The parameter is used to coast to stop for external terminal control mode . the
inverter will coast to stop when the terminal closed .
29：Commnad switch to terminal
The running command channel forced switched to terminal running commnad
channel when the terminal is valid . it will restore previous running command channel
after the terminal disconnected .

-118-
 Chapter 6 Detailed function description

30：PLC reset
When selecting PLC function . whether automatically input or terminal manual
input .Closing the terminal will clear the internal memory of PLC status infromation .
Disconnect the terminal .PLC restart .
31：PLC input
When PLC input model is terminal valid . the terminal is valid and PLC running
valid .
32： Count input
For receiving an external pulse signal as the count value.
33： Frequency switch to the combination
The terminal is valid, the frequency given channel forced to switch to combination
channel, then restore the original frequency given channel after disconnecting the
terminal.
34：Count clear
When set this function , this terminal and COM terminal switch on, the counter
value becomes zero.

Item 24 is only valid for multi-functional port X8. The

maximum frequency of input pulse is 20KHz, the amplitude
for low voltage is 0V, high voltage is 18 ~ 26V.

F5.08 ON/OFF filter time

Setting range: 1～100 Factory setting:5

This parameters is used to set filter strength of terminals(X1~X8). When the

interference is heavy .the user should increase this value to prevent malfunction .

-119-
 Chapter 6 Detailed function description

F5.09 Terminal control running mode

Setting Range:0~3 Factory Setting :0.

This parameter defines four different control modes that control the inverter
operation through external terminal .
0：2-wire control mode 1
1：2-wire control mode 2
X1 setting : Forward running X2:Reverse running
As shown in table 6-3 and table 6-11
Table 6-3 2-wire controlmode running command

Switch 2-wire control 2-wire control

state mode 1 mode 2

Running Running
K2 K1
command 1 command 2

OFF OFF STOP STOP

ON OFF REVERSE STOP
OFF ON FORWARD FORWARD
ON ON STOP REVERSE

Note: connection is ON .disconnect is OFF.

K1
X1
K2
X2
COM

Fig.6-11 2-wire control diagram

-120-
 Chapter 6 Detailed function description

2：3-wire control mode 1

K1 X1
K2 X2
K3 X3
COM

Fig.6-12 3-wire control mode diagram

3：3-wire control mode 2

3-Wire control shown in 6-10.X1 set the Forward running .X2 is reverse running .
X3 is 3-wire running control terminal .
3-wire control mode 1 3-wire control mode 2
K1----- running switch K1----- Forward
K2----- Forward and Reverse shifting K2----- Reverse
K3-----Stop K3----- Stop

F5.10 UP/DOWN terminal change speed rate

Setting range:0.01～50.00Hz/s Factory setting:0.50Hz/s

Terminal UP/DWON regulates the incremental rate of setting frequency .

F5.11 AVI lower limit

Setting range:0.00～10.00V Factory setting:0.00V
F5.12 Frequency of free stop
Setting range：0.00-F0.05 Factory setting：30.00Hz
F5.13 AVI upper limit
Setting range:0.00～10.00V Factory setting:10.00V

-121-
 Chapter 6 Detailed function description

F5.14 AVI upper limit corresponding setting

Setting range:-100.0～100.0% Factory setting:100.0%
F5.15 AVIinput filter time
Setting range:0.00～10.00s Factory setting: 0.10s
F5.16 ACI lower limit
Setting range:0.00～10.00V Factory setting:0.00V
F5.17 ACI lower limit corresponding setting
Setting range:-100.0～100.0% Factory setting:0.0%
F5.18 ACI upper limit
Setting range:0.00～10.00V Factory setting:10.00V
F5.19 ACI upper limit corresponding setting
Setting range :-100.0～100.0% Factory setting:100.0%
F5.20 ACI input filter time
Setting range:0.00～10.00s Factory setting:0.10s
F5.21 Maximum pulse input
Setting range:0.0～20.0kHz Factory setting:20.0kHz
F5.22 pulse input lower limit
Setting range:0.0～20.0kHz Factory setting:0.0kHz
F5.23 pulse input lower limit corresponding setting
Setting range:-100.0～100.0% Factory setting:0.0%
F5.24 pulse input upper limit
Setting range:0.0～20.0kHz Factory setting:20.0kHz
F5.25 pulse input upper limit corresponding setting
Setting range:-100.0～100.0% Factory setting:100.0%

The above function code determine the relationship between analog (pulse)input
and analog (pulse ) input corresponding setting. When the analog input voltage exceeds
the range between lowerlimit and upper limit . it will be regarded as the upper limit or
lower limit .

-122-
 Chapter 6 Detailed function description

For different applications . the corresponding value of100.0% analog setting is

different . For details. Please refer to description of each application .as shown in
Figure 6-13.

、linkage proportion setting .

Figure 6-13 Analog given and setting

F5.26 Center voltage hysteresis loop width

Setting Range:0.00～10.00V Factory Setting:0.15V

The paramter is used to adjust the center voltage hysteresis value when F0.03 =8.
and will not make calculations withine this range .

F5.27 Cooling Fan control

Setting Range：0-1 Factory Setting：0

0:Auto operation : The fan will run when the inverter starts . and will stop when
the inverter stops.
1:The cooling fan is running when the inverter energized on .

-123-
 Chapter 6 Detailed function description

F6 Group-Output terminals

F6.00 Y1 output selection

Setting range:0～16 Factory setting: 1
F6.01 Y2 output selection
Setting range:0～16 Factory setting: 2
F6.02 Relay output selection
Setting range:0～16 Factory setting: 3

This group parameters defines the content represented by the open collector
output terminals Y1, Y2, and relay.
0：No output
1：Forward running : Inverter runs forward.has output frequency .Output ON
signal at this time .
2：Reverse tunning : Inverter runs reverse.has output frequency .Output ON
signal at this time .
3： Fault output : ON: inverter is in fault state .
4：Frequency level detection FDT arrival: Please refer to functional code
F8.13.F8.14 for detailed description.
5：frequency reached Please refer to description of P8.15.
6：Zero speed running ON: The running frequency of inverter is Zero.
7：Upper limit frequency reached ON: Running frequency reaches the value
of upper limit frequency.
8：Lower frequency limit reached ON: Running frequency reaches to the
value of lower limit frequency .

-124-
 Chapter 6 Detailed function description

9:Running
When the inverter is running .ON signal will be output .
10: PLC stage completed
Upon the completion of current step of simple PLC running .ON signal with the
width of 200ms will be output .
11:PLC cycle completed
Upon the completion of a cycle of simple PLC running .ON signal with the width
of 200ms will be output .
12: Overload Pre-alarm
When the inverter output current exceeds overload warning level, An low level
active signal will be output after setting the alarm delay time .
13: Specified count value reached
Refer to the fuction of F6.19.F6.20.
14: Setting count value reached
Refer to the fuction of F6.19.F6.20.
15: Reserved
16.Under load output

F6.03 AFM output selection

Setting range:0～14 Factory setting: 0
F6.08 DFM output selection
Setting range:0～14 Factory setting: 0

This function is used to select the analog output of the AFM and the digital output
of the DFM output signal. As shown in Table 6-4.

-125-
 Chapter 6 Detailed function description

Table 6-4 analog AFM and digital DFM output signal

Setting Fuction Range

0 Running frequency 0～ Maximum frequency

1 Setting frequency 0～Maximum frequency

2 Motor speed 0～2 xrated synchronous speed of motor

3 Output current 0～2 x inverter rated current

4 Output Voltage 0～1.5 x inverter rated voltage

5 Output power 0～2 x rated power

6 Output torque 0～2 x Motor rated current

7 Analog AVI input 0～10V

8 Analog ACI input 0～10V/0～20mA

9～10 Reserved Reserved

F6.04 AFM output lower limit

Setting range:0.0～100.0% Factory setting:0.0%
F6.05 The lower limit corresponding to the AFM output
Setting range:0.00～10.00V Factory setting:0.00V
F6.06 AFM output upper limit
Setting range:0.0～100.0% Factory setting:100.0%
F6.07 The upper limit corresponding to the AFM output
Setting range:0.00～10.00V Factory setting:10.00V
F6.09 DFM output lower limit
Setting range:0.0～100.0% Factory setting:0.0%

-126-
 Chapter 6 Detailed function description

F6.10 The lower limit corresponding to the DFM output

Setting range:0.00～10.0kHz Factory setting:0.0kHz
F6.11 DFM output upper limiting
Setting range:0.0～100.0% Factory setting:100.0%

F6.12 The lower limit corresponding to the DFM output

Setting range:0.00～10.00V Factory setting:10.0kHz

The above function code determine the relationship between analog output
voltage /current and the corresponding output value .when the analog output value
exceeds the range between lower limit and upper limit. It will output the upper limit or
lower limit . When analog output is current output .1mA is corresponding to 0.5V.
For different applications .the corresponding value of 100.0% analog output is
different . For details . Please efer to the description of each application .

Figure 6-14 Relationship between AO and corresponding setting

-127-
 Chapter 6 Detailed function description

F6.13 Y1 delay conduction time

Setting Range :0.1～3600.0s Factory Setting: 0.0s
F6.14 Y1 delay shut off time
Setting Range:0.1～3600.0s Factory Setting: 0.0s
F6.15 Y2 delay conduction time
Setting Range:0.1～3600.0s Factory Setting: 0.0s
F6.16 Y2 delay shut off time
Setting Range:0.1～3600.0s Factory Setting: 0.0s

The parameter is used to control the Y1, Y2 conduction and turn-off delay time.

F6.17 Relay delay closing time

Setting Range:0.1～3600.0s Factory Setting: 0.0s
F6.18 Relay delay disconnect time
Setting Range:0.1～3600.0s Factory Setting: 0.0s

The parameter is used to control the output relay closing and disconnect delay
time.

F6.19 Set the count value

Setting Range:0～9999 Factory Setting: 0
F6.20 Specified the count value
Setting Range:0～F6.19 Factory Setting: 0

F6.21 The count coefficient

Setting Range:0.01～99.99 Factory Setting: 1.00

The parameter specifies thw count working of the counter, counter pulse input
from the external terminal X8. When the counter counting external pluse value reaches

-128-
 Chapter 6 Detailed function description

the value of parameters F6.19.the corresponding multi-function output terminal (Setting

counting value reached ). Output signal will be with a width of the effective period of
200ms, and the counter is cleared.
When the count value of the counter reaches a predetermined value of F6.20,
the corresponding multi-function output terminal (designated count value) output valid
signal. If you continue to count exceeds the parameters F6.19 and set value when the
counter is cleared, the output valid signal will undone.
As shown in Figure 6-15: Y1 is set to couter value reached . Y2 is set to specify
count value reached, F6.19 is set to 8, F6.20 set to 5.

X6 1 2 3 4 5 6 7 8 1

Y1
200ms

Y2
Fig.6-15 Counter set value and specified value reached schemati

F6.22 Counter working mode selection

Setting Range:00～11 Factory Setting : 00

The parameter specifies the counter working mode and clear mode.
LED Unit’s Place：clear mode
0：Auto
1：Manual
LED Decade：Count mode
0：Up counter
1：Down counter
LED Hundreds 、Thousand place Reserved

-129-
 Chapter 6 Detailed function description

F7 Group-Human-machine interface

F7.00 The user password

Setting range: 0～65535 Factory setting :0

The password protection function will be valid when set to be any nonzero data .
When F7.00 is set to be 0000, the user’s password set before will be cleared and
the password protection gunction will be disable .
After the password has been set and becomes valid .the user can not access
menu if the user’s password is not correct .Only when a correct the user’s password
is input, the user can see and modify the parameters .Please keep the user’s password
in mind .
The password will be valid in 1 mintue after retreat the function code edition state .
Press MODE to enter into the function code edition state after the password takes effect .
0.0.0.0.” will be displayed .the operator should input correct password .

F7.01 The initial selection when Power on

Setting Range :0x0000～0x0C1F Factory Setting :0x0000

The function code determines the displayed content when the inverter is power
on ,The units of LED, decade bits are used to set the running status display selection;
hundreds and thousands of LED are used to set the stop status display selection. The
initial content display can only select a project, data format is hexadecimal.
Specific display content corresponding to parameter value refer to F7.06-F7.08.
For examole: The running state and stop state will dispaly the inital count value and
input AC voltage . the setting is 0x0A10 .the count value is 16th bit .so hexadecimal
is 10. the input ac voltage is the 10 bit .so the hex is 0A.

-130-
 Chapter 6 Detailed function description

F7.02 Parameter copy

Setting range : 0～4 Factory setting : 0

The parameter determines the method of parameter copy .

0：No operation
1：All parameters will be uploaded to keyboard . the functions parameters
are copied to the keyboard.
2：All parameters will be download to the machine . the parameters of the
keyboard are copied to the machine.(Except F2 group.)
3：Reseved
4：The keyboard function parameters are download to the machine . the
parameters of the keboard are copied to the machine .(all).

F7.03 REV/JOG function selection

Setting ragne : 0～4 Factory setting : 0

This function is used to set the REV/JOG keys on the operation panel.
0：Jog operation
1：FWD/REV switching
2： Clear UP/DOWN setting
3:Reverse Running
4: Fast query : is used to query for the modification parameters.

F7.04 STOP/RESET key stop function selection

Setting range: 0～3 Factory setting : 0

The function code defines the STOP/RESET stop function selection .

0：Valid when keypad control
1： Valid when keypad or terminal control
2：Valid when keypad or communication control

-131-
 Chapter 6 Detailed function description

3：Always valid
The reset function of STOP/RESET Is always valid .

F7.05 Gauge Range Decimal Place

Setting range：0～3 Factory setting：2
F7.06 Running state display parameter selection 1
Setting range :0～0xFFFF Factory setting :0x00FF
F7.07 Running state display parameter selection 2
Setting Range :0～0x3 Factory setting :0x0

The parameters will display the function code when the inverter is running .
which is a 16-bit binary number, if Bit is 1, the corresponding parameters can be
running through the SHIFT / "key to view. If Bit is 0 .then the corresponding parameters
will not be displayed. Set the function code F7.06 .change a binary number to a
hexadecimal number, enter the function code. the conent are as follows :

Table 6-5 The display content correspomding to running

BIT15 BIT14 BIT13 BIT12 BIT11 BIT10 BIT9 BIT8 BIT5 BIT4 BIT3

The PLC
The The
Torque current Analog Analog PID PID current PLC
output input
setting step of ACI AVI feedback setting Reserved running Current
multi- terminal terminal
value Value Value value value remaining speed
step state state
time
F7.06 F7.07
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 BIT2 BIT1 BIT0

DC PLC
Output Output Running Output Output Setting Running Output Count
bus average
torque power torque current voltage frequency frequency torque Value
voltage speed

-132-
 Chapter 6 Detailed function description

F7.08 Stop state display parameter selection

Setting range :0～0x7FF Factory setting:0x40F

The setting of this function code is the same as that of F7.06. when the inverters
are in the stopping state . the displaying of the parameter is determined by the function
code.
Table 6-6 The display content correspomding to stop
BIT15 BIT14 BIT13 BIT12 BIT11 BIT10 BIT9 BIT8
The
The
current The
Current PLC Linkage AC Torque
running Count current
speed average Proportion input setting
remaining value step of
of speed Coefficient voltage value
time of multi-step
PLC
PLC
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0

Analog Analog PID PID Output Input DC

Setting
ACI AVI feedback setting terminal terminal bus
frequency
value value value value state state voltage

F7.09 IGBT module temperature

Setting range: 0.0～100.0℃ Factory Setting:- - - -

F7.10 Software version

Setting range: 0.00～9.99 Factory Setting:- - - -

F7.11 Accumulated running time

Setting range: 0～65535 Factory Setting:- - - -

F7.12 Runtime password setting

Setting Range：0-65535 Factory Setting:- - - -

F7.13 Runtime setting

Setting Range：0-65535h Factory Setting:- - - -

-133-
 Chapter 6 Detailed function description

Setting as below：
1、F7.12 must be greater than 10, F7.13 must not be 0, if the password is greater
than 10 and the time setting is 0, reported fault “over”; if the password is less than 10,
the time setting is not 0, limit invalid.
2、Set F7.12 any number greater than 10, which is the password.
3、F7.13 is setting as any number, not including 0, is the time range. Unit: hour
4.F7.12 and F7.13 set to valid to change again, you must enter the correct password
to modify, or can not be modified.
5、If want to cancel the time limit, enter the correct password and change the time
and password to 0.
6、Once the password is set, please keep in mind the password, if not the correct
password will not be cleared, please use caution.

F7.14 The previous two fault type

Setting range:0～29 Factory Setting:- - - -
F7.15 The previous fault type
Setting range:0～29 Factory Setting:- - - -
F7.16 The current fault type
Setting range:0～29 Factory Setting:- - - -
F7.17 The current fault running frequency
Setting range:0.00～600.00Hz Factory Setting:- - - -
F7.18 The current fault output current
Setting range:0.1～2000.0A Factory Setting:- - - -
F7.19 The current fault DC bus voltage
Setting range:0～1000V Factory Setting:- - - -
F7.20 The current fault temperature
Setting Range: 0.0～100.0℃ Factory Setting:- - - -
F7.21 The current fault input terminal state
Setting range:0～0xFFFF Factory Setting:- - - -
F7.22 The current fault output terminal state
Setting range:0～0xFFFF Factory Setting:- - - -

-134-
 Chapter 6 Detailed function description

The state of current fault input terminal is displayed as decimal figures.Display

the state of all digital input terminals at the latest fault . The order is :

BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0

X8 X7 X6 X5 X4 X3 X2 X1

Current input terminal is ON and the corresponding bit is 0. The state of the digital
input terminal at fault can be known through this value .
The state of current fault output terminal is displayed as decimal figures .Display
the state of all digital output terminals at the latest fault . The order is :

BIT2 BIT1 BIT0

RY Y2 Y1

Current output terminal is ON and the corresponding bit is 1.If current output
terminal is OFF and the corresponding bit is 0.the state of the digital input terminal at
fault can be known through this value .

F8 Group-Enhanced function

F8.00 Acceleration time 2

Setting range : 0.1～3600.0s Factory setting:Depends on model
F8.01 Deceleration time 2
Setting range : 0.1～3600.0s Factory setting: Depends on model

Please refer to the instructions of F0.08 and F0.09 for detailed information .
Acc/Dec time 1 and 2 can be switched through multi-function digital input terminals .
Please refer to F5 Group for details information.
For details ,Please refer to description of F0.08 and F0.09.

-135-
 Chapter 6 Detailed function description

F8.02 Jog frequency

Setting range:0.00～F0.04 Factory setting:5.00Hz
F8.03 Jog acceleration time
Setting range:0.1～3600.0s Factory setting:Depend on model
F8.04 Jog deceleration time
Setting range:0.1～3600.0s Factory setting:Depend on model

The meaning and factory setting of F8.02-f8.04 are shown as Figure 6-16.

Figure 6-16 Jog running frequency and Acc./Dec. time

Jog running : The starting mode F1.00 set 0 and stop

mode F1.05 set to 0 to stop.
The operation panel, the control terminal and the serial
port can be jog control.
In different kinds of operation conditions .Press the jog key .
Jog frequency running is priority to progress .

-136-
 Chapter 6 Detailed function description

F8.05 Skip frequency

Setting range :0.00～F0.04 Factory setting :0.00Hz
F8.06 Skip frequency bandwidth
Setting range :0.00～F0.04 Factory setting :0.00Hz

The settings of F8.05 -F8.06 is mainly to keep the inverter awya from the
mechanical resonance with the load , you can set a skip frequency point. When the
skip frequency point is set to 0, the skip frequency is invalid .

Figure 6-17 Skip frequency setting

In the process of acceleration, deceleration operation .the dive

can not jump the skip frequency .

F8.07 Traverse amplitude

Setting range :0.0～100.0% Factory setting :0.0%
F8.08 Jitter frequency
Setting range :0.0～50.0% Factory setting:0.0%

-137-
 Chapter 6 Detailed function description

F8.09 Rise time of traverse

Setting range :0.1～3600.0s Factory setting:5.0s
F8.10 Fall time of traverse
Setting range:0.1～3600.0s Factory setting:5.0s

Traverse operation is widely used in textile and chemincal fiber industry . The
typical application is hown in the following figure .
Traverse function means the output frequency of the inverter wobbles with
reference frequency as the centre . The track of the output frequency is shown as
Figure 6-18. The traverse bandwidth is set by F8.07. when F8.07 is set to 0. The
traverse bandwidth is o and has no action .

Figure6-18 Traverse operation diagram

Traverse amplitude: Traverse operation frequency is on the subject of upper ，

lower frequency constraints.
Traverse amplitude (AW)= center frequency (CF)*F8.07
Jitter frequency = traverse amplitude(AW)*F8.08
Rise time of traverse: Indicates the time rising from the lowest traverse frequency
to the highest traverse frequency .
Fall time of traverse: Indicates the time falling from the highest traverse frequency
to the lowest traverse frequency.

-138-
 Chapter 6 Detailed function description

F8.11 Fault auto reset times

Setting range :0～9999 Factory setting :0
F8.12 Fault reset interval time
Setting range:0.1～100.0s Factory setting:1.0s

Auto reset times: when the inverter selects auto reset times . This parameter is
used to set the times of auto reset .But if the inverter reset continuously for more than
the set time .the inverter will stop for fault and the user has to deal with the problem by
hands.
Reset interval: This parameter selects the interval time from fault accurring to
auto reset .

F8.13 FDT Level

Setting range:0.00Hz～F0.04 Factory setting :50.00Hz
F8.14 FDT lag
Setting range :0.0～100.0% Factory setting:5.0%

This group of parameters used to set the frequency detection level , when the
output frequency is increased by more than than FDT settings. The output open
collector signal (lower level), when the ouput frequency drops to the FDT lift the level .
The output is invalid signals (high resistance). Shown in Figure 6-19.

Figure 6-19 DFT level diagram

-139-
 Chapter 6 Detailed function description

F8.15 Frequency arrival detecting range

Setting range :0.0～100.0% Factory setting :0.0%

When the output frequency is within the positive and negative deteacting range
of the setting frequency . The selected output terminal is valid output signal (low level),
As shown in Figure 6-20.

Figure 6-20 Frequency arriving detecting diagram

F8.16 Energy Brake threshold voltage

Setting range :115.0～140.0% Factory setting :125.0%
The function code is used to set the original bus voltage of the energy braking
(380V series is 530V, 220V series is 310V).Adjust the value properly can be brake the
load effectively .

F8.17 Coefficient of rotation speed

Setting range :0.1～999.9% Factory setting :100.0%
This parameter is used to calibrate the bias between actual mechanical speed
and rotation speed .the formula is as below:
Actual mechanical speed=120*output frequency *F8.17/Number of poles of motor .

F8.18 Enery braking output starting value

Setting Range :0～100% Factory setting: 0%
control enery braking output proportional to of starting value .If it set to 50%, The
parameter will vary between 50%-100%.

-140-
 Chapter 6 Detailed function description

F8.19 Inverter overload pre-alram selection

Setting Range:00～12 Factory setting: 00
LED bit.overload pre-alarm detection selection
0: No detection
1: Running Detection
2:Constant speed detection
LED ten digit. overload pre-alarm action selection
0: No alarm, continue running
1: OL3 alarm, stop running.
LED Hundred digit.under load pre-alarm detection selection
0: No detection
1: Under load when Running Detection
2: Under load when Constant speed detection
LED Thousand digit .under load pre-alarm action selection
0:No Alarm . Continue running
1: UL4 Alarm .stop running .
F8.20 Overload pre-alram level
Setting Range :0.0～150.0% Factory setting: 130.0%
F8.21 Overload detection time
Setting Range：0.0～6500.0s Factory setting：5.0s
Overload pre-alarm level defines the current threshold of overload pre-alarm
action . the setting range is relative to the percentage of rated current .The general
overload pre-alarm level should be set lower than the overload protection level.
When the output current reaches the overload pre-alarm level, and its continued
level exceeds to setting's overload pre-alarm action time .overload pre-alarm will be
action.shown in Figure 6-21.
Output Current

Time

High resistor High resistor

Time

-141-
 Chapter 6 Detailed function description

F8.22 The decrease rate of droop control frequency

Setting Range :0.00～15.00% Factory Setting : 0.00%
The inverter output frequency will vary with load . mainly used to drive the power
balance of the same load for multi-motor .
The proportional gain of ENA frequency increases . The bigger setting value .
The faster change . But it couldn’t too fast . The frequency increase too fast . The
motor shock badly.
ENA Integration time. The larger the setting, the smaller the frequency change.
The smaller the setting, the faster the frequency changes, but if the frequency increases
too fast. Motor shock badly.

F8.23 ENA Mode and Fan control

Setting Range：00-11 Factory Setting：00
F8.24 The proportional gain of ENA frequency increases
Setting Range：0-100 Factory Setting：0.10
The proportional gain of ENA frequency increases . The bigger setting value .
The faster change . But it couldn’t too fast . The frequency increase too fast . The
motor shock badly.

F8.25 ENA Integration time

Setting Range：0.01-100 Factory Setting：0.10
ENA Integration time. The larger the setting, the smaller the frequency change.
The smaller the setting, the faster the frequency changes, but if the frequency increases
too fast. Motor shock badly.

F9 Group-PID control
PID control is a common used method in process control.such as flow ,pressure
and temperature control .the principle is firstly detect the biad between preset value and
feedback value .then calculate output frequency of inverter accoding to proportional
gain .integral and differential time .Please refer to following figure 6-22.

-142-
 Chapter 6 Detailed function description

Target
value

Figure 6-22 PID control diagram

F9.00 PID given source selection

Setting range :0～5 Factory setting :0

0：Keypad（F9.01）
1：Analog chanel AVI given
2：Analog chanel ACI given
3：Remote communication given
4：Multi-step speed given
5: keyboard direct given
When frequency source select PID , F0.03 set to 5.F9 group function will be
effect . This parameter determines the goal of the process PID given channel. the
setting target of process PID is relative value . 100% preset value is corresponding to
100% of feedback value . the system will operate according to the relative value
(0 to 100%).

Multi-step given can set the parameters of FA group .

F9.01 Keyboard preset PID given

Seting range :0.00～F9.16 Factory setting :0.00M Pa

-143-
 Chapter 6 Detailed function description

Select F9.00 = 0, the target source is the keyboard given . This parameter is the
reference value as the amount of feedback.

F9.02 PID feedback source selection

Setting range :0～3 Factory setting :0

0：Analog channel AVI feedback

1：Analog channel ACI feedback
2：AVI+ACI feedback
3: Remote communication feedback
These parameters are used to select PID feedback channel .

Preset source and feedback source must not be same .

Otherwise given and feedback will be the same .the
difference is 0. PID will not work .

F9.03 PID output characteristics selection

Setting range :0～1 Factory setting :0

0：PID output is positive. When the feedback value is greater than the preset
value .Output frequency will be decreased .such as tension control in winding application .
1：PID output is negative . when the feedback value is greater than the preset
value .Output frequency will be increased .such as tension control in unwindling
application .

F9.04 Proportional gain Kp

Setting range :0.00～100.00 Factory setting :1.00

Proportional gain Kp determines the adjusting strength of the PID adjustor .the
large the value of P .the stronger the adjusting strength is .

-144-
 Chapter 6 Detailed function description

F9.05 Integral time Ti

Setting range:0.01～100.00s Factory setting:0.10s

The Integral time Ti determines the ratio between the output frequency change
speed and deviation. Integral role is the output value will integrate according to the
deviation , to eliminate the deviation of feedback value and given value . Integration
time is too large, the response is slow, slow response to external disturbances. The
integration time is smaller, faster response speed, but too small and easy to cause
oscillation.

F9.06 Differential time Td

Setting range:0.01～100.00s Factory setting :0.00s

Differential time Td: when the error between the feedback and the reference . a
proportional adjustment will be output.The adjustment only depends on the direction
and value of the error change other than the error itself .The derivation adjustment
controls the change of feedback signal according to the changing trend when it fluctuates.
Because the derivation may enlarge the interference to the shystem ,especially the
frequency-changing interference .Please use it carefully .

F9.07 Sample cycle T

Setting range:0.01～100.00s Factory setting:0.10s

Sample cycle T refers to the sampling cycle of feedback value. The PI regulator
calculates once in each samling cycle .the bigger thpe sampling cycle .the slower the
response is .

F9.08 Bias limit

Setting range:0.0～100.00% Factory setting:0.0%

-145-
 Chapter 6 Detailed function description

Bias limit defines the maximum bias between the feedback and the preset . PID
stops operation when the bias is within this range . Setting this parameter correctly is
helpful to improve the system output accuracy and stability .

Figure 6-23 Bias limit action diagram

F9.09 Feedback lost detecting value

Setting range:0.0～100.0% Factory setting :0.0%
F9.10 Feedback lost detecting time
Setting range: 0.0～3600.0s Factory setting: 1.0s

Feedback lost detecting value is relative to 100% .The system will detect the
feedback pf PID all the time .when the feedback value is below or equal to the feedback
offline detection value .the system will begin to count the detecting time . when the time
exceeds the feedback offline detection time .the system will report PIDE.

F9.11 Feedback gain

Setting range:0～200.0% Factory setting:100%

When the feedback value is not same as the actual target value . this parameter
can be used to adjust the feedback signal .

-146-
 Chapter 6 Detailed function description

F9.12 Awakening threshold range

Setting range:0.00～F9.16 Factory setting:0.50 MPa
F9.13 Awakening threshold detection time
Setting range:0.00～360.00s Factory setting:1.00s
F9.14 Sleep Frequency
Setting range：0.00～F0.04 Factory setting：.30.00Hz
F9.15 Sleep Frequency Detection Time
Setting range:0.00～360.00s Factory setting:1.00s

F9.12 is the water supply system of the pressure threshold from sleep into the
working state . when the pressure of the pipe network is less than the set value,Inverter
pass delay waiting of F9.13, the frequency of water supply system automatically
transferred to the working state from hibernation.
F9.14 refers to the lowest operating frequency of PID system from working state
to sleeping state.
When the feedback value is greater than or equal to the set value, and the inverter
PID system has adjusted the output frequency to the sleep frequency operation, the
inverter pass delay waiting of F9.15 and enters into a sleep state (zero speed
operation) waiting for awake .See Figure 6-24.

PID feedback value

PID Setting
Awaking threshold range

Output frequency

Sleep frequency

Figure 6-24 Sleep and Awake function diagram

-147-
 Chapter 6 Detailed function description

F9.16 The gauge range

Setting Range :0.00～20.00MPa Factory Setting: 20.00MPa

The parameter is used to set the gauge range .

F9.17 PID preset frequency

Setting Range :0.00～F0.05 Factory Setting:0.00Hz
F9.18 Preset frequency maintain time
Setting Range:0.00～360.00s Factory Setting:0.00s

This parameter is used to set the PID running frequency and time before running.

FA Group –Multi- step speed control

FA.00 PLC Mode

Setting Range:0000～1111 Factory Setting :0000

LED Unit’s Place ：PLC running mode selection

0：invalid
1：single circulation
2：continuous circulation
3：single circulation keep the final value .
LED Decade;PLC input selection
0：Automatic control
1：Terminal Control
LED Hundreds place :
PLC breakpoints recovery options
0：Restart from the first stage frequency.
1：Restart from running frequency .which is saved before the sunning is breaking .
2：Restart from setting frequency when running is break.

-148-
 Chapter 6 Detailed function description

PLC Thousands place:

PLC power failure save selection.
0：Non-save after power off
1：save after power off
Detailed functions of the operating mode
1：Simple PLC
Simple PLC is the inverter can automationcally stop after multi-step speed
running completed a cycle . the inverter will be given running command and then
start . If the running time for a certain stage is 0. The inverter will skipped the stage
into the next stage . As shown in Figure 6-25.

f8 f15
f7 a8 f14 a15
d16
f6
a7
f5 a6 f16
f4 d9 a14
a5
f3 f13
a4
f2 a3
f1 a2
a1 a13

a9 f9
a10 f10
d13
a11 f11

a12

f12

T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16

Fig.6-25 PLC / multi-speed single cycle running

f1～f16 are the running frequency for Stage 1-Stage16

T1～T16 are running time for Stage 1-Stage16.
a1～a15 are acceleration time for Stage 1-Stage15.
d1、d9 、 d13 and d16 are deceleration time for Stage 1、9、13、16.

-149-
 Chapter 6 Detailed function description

2：Continuous Cycle
The inverter multi-step running repeatedly cycle, the inverter will stop unless
stop command given, shown in Figure 6-26
f8 f15
f7 a8 f14 a15
d16
f6
a7
f5 a6 f16
f4 d9 a14
f3 a5
f13
a4 d1
f2 a3 f2 a3
f1 a2 f1 a2
a1 a13

a9 f9
a10 f10
d13
a11 f11

a12

f12

T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T1 T2

Fig.6-26 PLC / multi-speed continuous cycle running

3：Keep the final value after a single cycle

The inverter complete a single cycle . set the setting frequency and direction
running accoding to the last running time setting for multi-stage speed is not 0. as
shown Fig6-27. f8 f15
f7 a8 f14 a15
d16
f6 a7
f5 a6 f16
f4 d9 a14
f3 a5
f13
a4
f2 a3
f1 a2
a1 a13

a9 f9
a10 f10
d13
a11 f11

a12

f12

T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16

Fig.6-27 PLC / multi-speed keep the final value after a single cycle running

-150-
 Chapter 6 Detailed function description

FA.01 Multi-step speed 1

Setting range: F0.06-F0.04 Factory setting:0.00Hz

FA.02 Multi-step speed 2

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.03 Multi-step speed 3

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.04 Multi-step speed 4

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.05 Multi-step speed 5

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.06 Multi-step speed 6

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.07 Multi-step speed 7

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.08 Multi-step speed 8

Setting range: F0.06-F0.04 Factory setting : 0.00Hz

FA.09 Multi-step speed 9

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.10 Multi-step speed 10

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.11 Multi-step speed 11

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.12 Multi-step speed 12

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.13 Multi-step speed 13

Setting range: F0.06-F0.04 Factory setting: 0.00Hz

-151-
 Chapter 6 Detailed function description

FA.14 Multi-step speed 14

Setting range: F0.06-F0.04 Factory setting: 0.00Hz
FA.15 Multi-step speed 15
Setting range: F0.06-F0.04 Factory setting: 0.00Hz
FA.16 Multi-step speed 16
Setting range: F0.06-F0.04 Factory setting: 0.00Hz

FA.17 Unit of PLC Running time

Setting range: 0-1 Factory setting: 0
0： second
1: minute
FA.18 Curve selection
Setting range:0-1 Factory setting: 0

0: Mode 1- Linear operation

We ofen see 16 Mult-step controlling in inverter’s
In linera operation every step start with main acceleration /deceleration for
reching it given frequency”F” .

-152-
 Chapter 6 Detailed function description

Output
LINEAR OPERATION
Frequency

50
STEP 7 F7

40 STEP 6
STEP 8
STEP 9
STEP 5
30 STEP 10

STEP 4
STEP 11
20 STEP 3
Step
STEP 12
Time
STEP 2
STEP 13
10 STEP 1 F1
Acc STEP 14
Time
F14
0
T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15

2: Mode 2 (No wait time) -Gradual operation

In gradual operation frequency “F” increasing /decreaseing with respect to time
“T” in all 16 steps .If the step frequency is set to Zero . the step will be ended .

Output
GRADUAL OPERATION
Frequency

50
STEP 8 F8
40 STEP 7
STEP 9

F7
F9
F10 STEP 11
30 F5
STEP 6
F6 STEP 10
STEP 5 F11
F12
STEP 12
20 F3
STEP 4
F4
STEP 3
STEP 13

10 F1 F2
F13
F14
STEP 14
STEP 1 STEP 2

STEP 15
0
T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15

FA.19 Multi-speed direction source selection

Setting Range:0～1 Factory Setting :0

The multi-speed driection is external control when FA.16=0 .

The multi-speed driection decided by itself symbol when FA.16=1.
if FA.16 is negative . The multi-speed driection is reverse direction running .
Frequency set to 100.0% corresponding to the maximum frequency (F0.04).

-153-
 Chapter 6 Detailed function description

Multi-speed takes precedence over the keyboard, analog communication

frequency input, can select up to 16 steps speed through a combination of coding
Xn,specifically refer to the instructions F5 group parameter.
the start and stop chanel selection of multi-speed running are also determined
by the function code F0.01.

FA.20 PLC Accel/Decel Time 1

Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.21 PLC Accel/Decel Time 2
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.22 PLC Accel/Decel Time 3
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.23 PLC Accel/Decel Time 4
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.24 PLC Accel/Decel Time 5
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.25 PLC Accel/Decel Time 6
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.26 PLC Accel/Decel Time 7
Setting Range:0.01～3600.0s Factory Setting:20.0s
FA.27 PLC Accel/Decel Time 8
Setting Range:0.01～3600.0s Factory Setting:20.0s

FA.20 - FA.27 is used to set PLC acceleration and deceleration time of

multi-speed 1-16.

FA.28 Acceleration Selection 1 Factory Setting : 0x1111

FA.32 Deceleration Selection 1 Factory Setting: 0x1111

-154-
 Chapter 6 Detailed function description

Setting Range:
Unit’s Place: Multi-Speed 1 FA.20-FA.27.
Decade : Multi-Speed 2 FA.20-FA.27.
Hundreds place: Multi-Speed 3 FA.20-FA.27.
Thousands place：Multi-Speed 4 FA.20-FA.27.

FA.29 Acceleration Selection 2 Factory Setting : 0x1111

FA.33 Deceleration Selection 2 Factory Setting: 0x1111

Setting Range:
Unit’s Place : Multi-Speed 5 FA.20-FA.27.
Decade: Multi-Speed 6 FA.20-FA.27.
Hundreds place : Multi-Speed 7 FA.20-FA.27.
Thousands place ：Multi-Speed 8 FA.20-FA.27.

FA.30 Acceleration Selection 3 Factory Setting : 0x1111

FA.34 Deceleration Selection 3 Factory Setting: 0x1111

Setting Range:
Unit’s Place : Multi-Speed 9 FA.20-FA.27.
Decade: Multi-Speed 10 FA.20-FA.27.
Hundreds place : Multi-Speed 11 FA.20-FA.27.
Thousands place ：Multi-Speed 12 FA.20-FA.27.

FA.31 Acceleration Selection 4 Factory Setting : 0x1111

FA.35 Deceleration Selection 4 Factory Setting: 0x1111

-155-
 Chapter 6 Detailed function description

Setting Range:
Unit’s Place : Multi-Speed 13 FA.20-FA.27.
Decade: Multi-Speed 14 FA.20-FA.27.
Hundreds place : Multi-Speed 15 FA.20-FA.27.
Thousands place ：Multi-Speed 16 FA.20-FA.27.

FA.36 Direction Selection 1 Factory Setting: 0x0000

Setting Range:
Unit’s Place : Multi-Speed 1 (0-1) 0:Forward 1:Reverse
Decade: Multi-Speed 2 (0-1) 0:Forward 1:Reverse
Hundreds place: Multi-Speed 3 (0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 4 (0-1) 0:Forward 1:Reverse

FA.37 Direction Selection 2 Factory Setting: 0x0000

Setting Range:
Unit’s Place : Multi-Speed 5 (0-1) 0:Forward 1:Reverse
Decade: Multi-Speed 6 (0-1) 0:Forward 1:Reverse
Hundreds place: Multi-Speed 7 (0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 8 (0-1) 0:Forward 1:Reverse

FA.38 Direction Selection 3 Factory Setting: 0x0000

Setting Range:
Unit’s Place : Multi-Speed 9 (0-1) 0:Forward 1:Reverse
Decade: Multi-Speed 10 (0-1) 0:Forward 1:Reverse
Hundreds place: Multi-Speed 11 (0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 12 (0-1) 0:Forward 1:Reverse

-156-
 Chapter 6 Detailed function description

FA.39 Direction Selection 4 Factory Setting: 0x0000

Setting Range
Unit’s Place : Multi-Speed 13 (0-1) 0:Forward 1:Reverse
Decade: Multi-Speed 14 (0-1) 0:Forward 1:Reverse
Hundreds place: Multi-Speed 15 (0-1) 0:Forward 1:Reverse
Thousands place: Multi-Speed 16 (0-1) 0:Forward 1:Reverse

FA.40 PLC Running Time 1

Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.41 PLC Running Time 2
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.42 PLC Running Time 3
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.43 PLC Running Time 4
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.44 PLC Running Time 5
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.45 PLC Running Time 6
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.46 PLC Running Time 7
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.47 PLC Running Time 8
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.48 PLC Running Time 9
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.49 PLC Running Time 10
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)

-157-
 Chapter 6 Detailed function description

FA.50 PLC Running Time 11

Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.51 PLC Running Time 12
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.52 PLC Running Time 13
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.53 PLC Running Time 14
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.54 PLC Running Time 15
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)
FA.55 PLC Running Time 16
Setting Range : 0.0-6553.5 S(Min) Factory Setting : 0.0S(Min)

FA.40- FA.55 is used to set PLC multi-speed running time 1-16.

Fb Group –Protection function

Fb.00 Motor overload protection

Setting range :0～2 Factory setting :2

0：Disable.
without motor overload protection features (caution), at this time the drive don't
have overload protection for the load motor.
1：For normal motor . (with low speed compensation) .the lower the speed,the
poorer the cooling effect .based on this reason . If output frequency is lower tha 30Hz.
The inverter will reduce the motor overload protection threshold to prevent normal
motor from overheat .
2：The variable frequency motor (without low speed compensation ). As the
cooling effect of variable frequency motor has nothing to do with running speed . it is
not required to adjust the motor overload protection threshold.

-158-
 Chapter 6 Detailed function description

Fb.01 Motor overload protection current

Setting range:20.0～120.0% Factory setting:100.0%

If the power rating of the inverter do not match with the motor , you can modify
the parameters to achieve the purpose of protecting the motor. as shown in Figure 6-28.
The value cn be determined by the following formula :
Motor overload protection current=(motor rated current/inverter rated current)*100%.

Time

Figure 6-28 Motor overload protection curve

Fb.02 Momentary power drop frequency point

Setting range :70.0～110.0% Factory setting:80.0%
Fb.03 Momentary power drop frequency rate of decline
Setting range:0.00～F0.04 Factory setting:0.00Hz

If Fb.03 is set to 0. Momentary power drop frequency is invalid .

-159-
 Chapter 6 Detailed function description

Momentary power drop frequency point enable the inverter to perform low voltage
compensation when DC bus voltage drops below Fb.02. the inverter can continue to
run without tripping by reducing its output frequency and feedback energy via motor.

Please adjust these two parameters properly .It can avoid

in the switch of the power grid . and production stop
caused by inverter protection .

Fb.04 Over-voltage stall protection

Setting range : 0～1 Factory setting:1
Fb.05 Over-voltage stall protection voltage
Setting range:110～150% Factory setting:130%

0：Disable .
1：Enable
During deceleration .the motor’s decelerating rate may be lower than that of
inverter’s output frequency due to the load inertia .at this time .the motor will feed the
energy back to the inverter .resulting in DC bus voltage rise .If no measure taken .the
inverter will trip due to over voltage .
Over-Voltage stall protection iis the inverter detects DC bus voltage .
And compares it with over voltage stall protection point Fb.05. (Relative to the
standard bus voltage: 380V Series 530,220 V Series 310V).
If DC bus voltage exceeds Fb.05, the inverter will stop reducing its output frequency .
when the DC bus voltage become lower than Fb.05. the deceleration continues , as
shown in following figure 6-29.

-160-
 Chapter 6 Detailed function description

Figure 6-29 Over voltage stall function

Fb.06 Auto current limiting threshold

Setting range: 20～200% Factory Setting: 160%
Fb.07 Frequency decrease rate when current limiting
Setting range: 0.00～100.00Hz/s Factory Setting: 10.00Hz/s

Auto current limiting is used to limit the current of inverter smaller than the value
determined by Fb.06 in real time. Therefore the inverter will not trip due to surge
over-current. This function is especially useful for the applications with big load inertia
or step change of load.
Fb.06 is a percentage of the inverter's rated current.
Fb.07 defines the decrease rate of output frequency when this function is active.
If Fb.06 is too small, overload fault may occur. If it is too big, the frequency will change
too sharply, therefore, the feedback energy of motor will be too large and may cause
over-voltage fault. This function is always enabled during acceleration and deceleration.
Constant speed current limiting is valid or not determined by Fd.09.

-161-
 Chapter 6 Detailed function description

Note:
* During auto current limiting process, the inverter's output frequency may change;
therefore, it is recommended not to enable the function when requires the inverter's
output frequency stable.
* During auto current limiting process, if Fb.06 is too low, the overload capacity
will be impacted.
Please refer to following figure.

Fig 6-30 Auto current limiting function

Fb.08 Input phase loss protection selection

Setting Range: 0～2 Factory Setting : Depend on the model

In standay (hardware detectiuon valid) or running (Software or hardward detection

valid), The inverter will apprears LP input phase loss protection due to the power phase
shortage and three phase input power imbalance
0：Invalid

1：software detect is valid

2：hardware detect is valid

-162-
 Chapter 6 Detailed function description

The software detection is only valid for the model

G030T4/P037T4and G015T2 and below power.No
hardware detection.While there have software and
hardware options when the inverter is power bigger
than 30kW.

Fb.09 Under load protection current

Setting Range：0～150.0 Factory Setting：0

Fb.10 Under load protection Time

Setting Range：5.0～6500.0 Factory Setting：5.0

FC Group Serial communication

FC.00 Local address
Setting range: 0～247 Factory setting : 1

This parameter determines the slave address used for communication with
master. The value "0" is the broadcast address.

FC.01 Baud rate selection

Setting range: 0～5 Factory Setting: 4

This parameter can set the date transmission rate during serial communication.
Note: The baud rate of master and slave address must be the same.

-163-
 Chapter 6 Detailed function description

0：1200BPS
1：2400BPS
2：4800BPS
3：9600BPS
4：19200BPS
5：38400BPS

FC.02 Data bit check setting

Setting Range : 0～17 Factory Setting :1

This parameter defines the baud rate in serial communication, and data format
used in protocols , only a consistent format can be normal communication.
0:No parity check （ N，8，1）for RTU
1: Even parity check（E，8，1）for RTU
2: Odd parity check（O，8，1）for RTU
3: No parity check（N，8，2）for RTU
4: Even parity check（E，8，2）for RTU
5: Odd parity check（O，8，2）for RTU
6: No parity check（N，7，1）for ASCII
7 Even parity check（E，7，1）for ASCII
8: Odd parity check（O，7，1）for ASCII
9: No parity check（N，7，2）for ASCII
10: Even parity check（E，7，2）for ASCII
11: Odd parity check（O，7，2）for ASCII
12: No parity check（N，8，1）for ASCII
13: Even parity check（E，8，1）for ASCII
14: Odd parity check（O，8，1）for ASCII
15: No parity check （N，8，2）for ASCII
16: Even parity check（E，8，2）for ASCII
17: Odd parity check（O，8，2）for ASCII

-164-
 Chapter 6 Detailed function description

The upper computer and the data format of the inverter must be consistent .
Otherwise , Communication can't work .

FC.03 Communication answer delay time

Setting range: 0～200ms Factory Setting: 5ms

Answer delay: The interval time between the data receiving of the inverter and
data sending to the upper monitor. If the answer delay is shorter than the system time,
then it is subject to the system time, and if the answer delay is longer than the system,
then the waiting time should be prolonged after the data processing to achieve the
answer delay and then to send data to the upper monitor.

FC.04 Communication timeout fault time

Setting range: 0.0～200.0s Factory Setting: 0.0s

If the function code is set to 0.0s, this parameter is invalid.

If the function code is set to a valid value, when the interval time exceeds the
communication overtime, the system will report communication fault (CE 1).
Generally, the parameter is set to invalid. If the parameter is set in a continuous
communication system, the communication state can be monitored.
If it doesn't receive correct data signal during the delay time of FC.04, the inverter
will determine stop or remain the state according to the solution of communication fault.

FC.05 Communication error action

Setting range: 0～3 Factory Setting: 1

0: Alarm and coast to stop

1: Do not alarm and keep running
2: Do not alarm and stop at the stopping method ( only for communication control
mode )

-165-
 Chapter 6 Detailed function description

3: Do not alarm and stop at the stopping method (for all communication control
modes )
In the abnormal situation, the inverter can act through setting communication
fault processing. The selected running state of the inverter is: shield the CE fault, stop
or keep running.

FC.06 Response action

Setting range: 0～1 Factory Setting : 0

0: Response to reading and writing

1: No response to writing

FC.07 Communication parameters address mode

Setting Range:0～1 Factory Setting :0

0: The address is calculated according to the parameter group.

1:The address is calculated in sequence.increased one by one since F0.00.

FC.08 Linkage proportion coefficient

Setting Range:0.01～10.00 Factory Setting:1.00

when the local machine is set by the master inverter control . the setting frequency
is given by the main station . the parameter is used to set the local machine as a slave
via RS485/RS232 interface receiving the weight coefficient of the frequency command .
The actual setting frequency of the load machine is equal to the value of the
parameter is multiplied by RS485 / 232 interface receives the frequency setting
command value.

FC.09 Linkage proportion source selection

Setting Range:0～4 Factory Setting:0

-166-
 Chapter 6 Detailed function description

0：Keypad or Encoder Setting（FC.08）

1：Annlog AVI setting
2：Annlog ACI setting
3：Multi-stage setting
4：Keyboard or encoder direct setting

Fd Group Supplementary function

Fd.00 Low-frequency threshold of restraining oscillation

Setting range: 0～500 Factory Setting: 5
Fd.01 High-frequency threshold of restraining oscillation
Setting range: 0～500 Factory Setting:5

Most motors may have current oscillation at some frequency point. Please be
cautious to adjust these parameters to weaken oscillation.
This function is only valid when Fb.04 is set to be 0. The smaller the value of
Fd.00 and Fd.01, the stronger the restraining effect.

Fd.02 Amplitude of restraining oscillation

Setting range: 0～100 Factory Setting: 10

This parameter is used to limit the strength of restraining oscillation. If the value
of Fd.02 is too big, it may cause inverter over current. It should be set a little bit
smaller for large power motor, vice versa.

Fd.03 Threshold high-low frequency of restraining oscillation

Setting range: 0.00～F0.04 Factory Setting : 12.50Hz

If output frequency is greater than Fd.00 takes effect, otherwise Fd.01 takes
effect.

-167-
 Chapter 6 Detailed function description

Fd.04 Restrain oscillation

Setting range:0～1 Factory setting:1

0：Enabled
1：Disabled
Motor always has current oscillation when its load is light. This will cause abnormal
operation even over-current. For details, please refer to description of Fd.00~Fd.03.

Fd.05 PWM mode

Setting range: 0～2 Factory Setting: 0

0: PWM mode 1 with low noise in lower frequency and high noise in higher
frequency.
1: PWM mode 2 with low noise. But it is need to be derated, because of higher
temperature rise.
2: PWM mode 3 with high noise. But it can more effectively restrain the oscillation.

Fd.06 Torque setting mode selection

Setting range: 0～5 Factory Setting: 0
Fd.07 Keypad torque setting
Setting range: -200.0～200.0% Factory Setting: 50%

0: Keypad
1: AVI
2: ACI
3: AVI+ACI
4: Multi-step setting
5: Communication
When torque control takes effect,
If Tset＞Tload , output frequency will increase continuously until it reaches upper
frequency limit.

-168-
 Chapter 6 Detailed function description

If Tset＜Tload，output frequency will decrease continuously until it reaches lower

frequency limit.
Inverter can run at any frequency between upper and lower frequency limit only
when Tset＝Tload。
Torque control can be seitched to speed control, vice versa.
Switching by multi-functional terminal: For example, if torque control is enabled
(P0.00=2), torque setting source is AVI, the value of multi-function terminal S5 is set to
20 (Disable torque control). When S5 is valid, control mode will switch from torque
control to speed control, vice versa.
When running at torque control mode, press the key: STOP/ RST, it will seitch to
speed control automatically.
If torque setting is positive, inverter will run forward; otherwise it will run reverse.
Note:
When running at torque control mode, the acceleration time has nothing to do
with F0.08.
The 100% of torque setting is corresponding to 100% of F3.07 (Torque limit).
For example, if torque setting source is keypad (Fd.06=0), Fd.07=80% and F3.07= 90%,
then Actual torque setting =80% ( Fd.07 )*90% (F3.07) = 72%.

Fd.08 Upper frequency limit selection

Setting range:0～4 Factory Setting:0

0: Keypad
1: AVI
2: ACI
3: Multi-step setting
4 : Communication

-169-
 Chapter 6 Detailed function description

The 100% of this parameter is corresponding to 100% of F0.04 ( maximum

frequency ). When running at torque control mode, output frequency can be adjusted
by changing upper frequency limit.

Fd.09 Auto current limiting selection

Setting range:0～1 Factory Setting:0

0: Enabled when constant speed

1: Disabled when constant speed
This function is always enabled during acceleration or deceleration period.
Auto current limiting function is used to prevent inverter trip over-current from
surge current. It is especially useful for the applications with big load inertia or step
change of load.
Note: During auto current limiting process, the inverter's output frequency may
change; therefore, it is recommended not to enable the function when output frequency
need to be stable.

Fd.10 Lower limit frequency running mode

Setting range :0～1 Factory Setting :0

Action mode when running frequency reached to lower limit frequency .

0: lower limit frequency running
1:Zero frequency running and DC braking .

Fd.11 Zero-frequency running braking current

Setting Range:0.0～150.0% Factory Setting :0.0%

Set value of DC braking current when Zero frequency operation .It’s invalid when
Fd.11=0%

-170-
-171-
-172-
 Inverter ① Reaches the overload
① Check the load
overload pre-alarm level,
② Set the appropriate Overload
pre-alarm ② Overload pre-alarm
pre-alarm value
arrived value is set improperly

-173-
-174-
-175-
-176-
-177-
-178-
-179-
-180-
-181-
 Chapter 9 Outline Dimension & Mounting Dimension
9.1 Inverter Outline Dimension & Mounting Dimension

Fig.9－1 (Model A) Inverter Outline & Dimension

Power Dimension(mm)
Inverter Model Fig.
(kW)
H H1 W W1 D d
ZVF300-G0R4T2/S2 0.4
ZVF300-G0R7T2/S2 0.75
ZVF300-G0R7T4 0.75 185 175 118 108 170 Ф5 Fig 9-1

ZVF300-G1R5T4 1.5
ZVF300-G2R2T4 2.2
ZVF300-G1R5T2/S2 1.5
185 175 118 108 190 Ф5 Fig 9-1
ZVF300-G2R2T2/S2 2.2
ZVF300-G3R7T2/S2 3.7
ZVF300-G3R7T4 3.7
215 205 145 135 193 Ф5 Fig.9-1
ZVF300-G5R5T4/P5R5T4 5.5
ZVF300-P7R5T4 7.5
ZVF300-G5R5T2 5.5
ZVF300-G7R5T4 7.5
265 253 185 174 215 Ф6 Fig.9-1
ZVF300-G011T4/P011T4 11
ZVF300-P015T4 15

-182-
 Fig. 9－2(Model B) Inverter Outline & Dimension

Power Dimension(mm)
Inverter Model Fig.
(kW) H H1 W W1 D d
ZVF300-G7R5T2 7.5
ZVF300-G015T4 15
380 360 220 145 230 Ф6 Fig.9-2
ZVF300-G018T4/P018T4 18.5
ZVF300-P022T4 22
ZVF300-G011T2 11
ZVF300-G015T2 15
ZVF300-G022T4/P022T4 22 460 443 260 177 268 Ф7 Fig.9-2
ZVF300-G030T4/P030T4 30
ZVF300-P037T4 37
ZVF300-G018T2 18.5
ZVF300-G022T2 22
ZVF300-G030T2 30
ZVF300-G037T4 37 620 603 265 182 300 Ф9 Fig.9-2
ZVF300-G045T4/P045T4 45
ZVF300-G055T4/P055T4 55
ZVF300-P075T4 75
ZVF300-G037T2 37
ZVF300-G045T2 45
ZVF300-G055T2 55
ZVF300-G075T4 75 720 702 365 240 360 Ф9 Fig.9-2
ZVF300-G090T4/P090T4 90
ZVF300-G110T4/P110T4 110
ZVF300-P132T4 132

-183-
 Fig.9－3 (Model C) Inverter Outline & Dimension

Power Dimension(mm)
Inverter Model Fig.
(kW) H H1 W W1 D d
ZVF300-G075T2 75
ZVF300-G090T2 90
ZVF300-G132T4 132
1190 - 493 - 390 - Fig.9-3
ZVF300-G160T4/P160T4 160
ZVF300-G185T4/P185T4 185
ZVF300-P200T4 200
ZVF300-G110T2 110
ZVF300-G200T4 200 1430 - 660 - 415 - Fig.9-3
ZVF300-G220T4/P220T4 220
ZVF300-G250T4/P250T4 250
ZVF300-G280T4/P280T4 280 1600 - 660 - 415 - Fig.9-3
ZVF300-P315T4 315
ZVF300-G315T4 315
ZVF300-G350T4/P350T4 350
1750 - 750 - 470 - Fig.9-3
ZVF300-G400T4/P400T4 400
ZVF300-P450T4 450
ZVF300-G450T4 450
ZVF300-G500T4/P500T4 500
1900 - 950 - 520 - Fig.9-3
ZVF300-G560T4/P560T4 560
ZVF300-G630T4/P630T4 630

-184-
9.2 Keypad Outline Dimension & Mounting Dimension

Fig. 9－4 Dimension of E-300 keypad

Extra mounting frame shall be assembled when E-300

operation panel is pulled out to install.
 wo installation frame are below :Fig.9-5 .Fig 9-6.
T

Fig.9－5 Hole dimension 1 of keypad. Fig.9－6 Hole dimension 2 of keypad

-185-
-186-
-187-
 1500W54Ω

2500W40Ω

2000W50Ω

2500W54Ω

2000W60Ω

16000W7.5Ω 2000W60Ω

-188-
-189-
-190-
-191-
-192-
-193-
-194-
-195-
-196-
-197-
-198-
-199-
-200-
-201-
-202-
-203-
-204-
-205-
word) word)

-206-
-207-
-208-
Parameter W/R
Address Function Description
Description Feature
Inverter x.xx stand for parameter number.
setting Fx.xxH For example：F5.05 expressed by
parameter 0505H .

0001H Forward running

0002H Reverserunning

0003H Jog forward

0004H Jog reverse

Control
1000H W/R
command
0005H Stop

0006H Coast to stop

0007H Reset fault

0008H Jog stop

0001H Forward running

Monitor 0002H Reverse running

1001H
state R
0003H Standby

0004H Fault

Communication Setting Range

(-10000~10000) Note: the
communication setting is the percentage
of the relative value(-100.00%~100.00%）.
Communic can be communication writing operation .
ation If it is set as frequency source, the value is the
2000H W/ R
setting percentage of maximum frequency
value (F0.04).If it is set as torque given ,the
corresponding is the percentage of the
torque upper limit (F3.07).If it is set as
PID settingvalue or feedback value , the
value is the percentage of the PID.

-209-
 3000H Running frequency R

3001H Setting frequency R

3002H Output current R

3003H Output voltage R

3004H Output rotation speed R

3005H Output power R

Monitor 3006H Output torque R

parameter
3007H DC bus voltage R

3008H PID setting value R

3009H PID feedback value R

300AH Input terminal state R

300BH Output terminal state R

300CH Analog AVI value R

300DH Analog ACI value R

Inverter
fault 5000H See the attached fig 3-1 R
address
Communication
fault 5001H See the attached fig 3-2 R
address

-210-
Data Fault Type Data Fault Type
00H No fault 0CH
Motor overload（OL1）

01H Over-current when 0DH Inverter overload

（ocA）
acceleration （OL2）

02H Over-current when 0EH

External fault（EF）
（ocd）
deceleration

03H Over-current when constant 0FH RS485

communication fault
（ocn）
speed running
（CE-1）

04H Over-voltage when 10H Reserved

（ovA）
acceleration

05H Over-voltage when 11H Current detection

（ovd）
deceleration fault（itE）

06H Over-voltage when 12H Keypad

constant speed running communication fault

（ovn） （CE-4）

07H Over-voltage when stop 13H Motor auto tuning

（ovS） fault（tE）

08H DC bus under voltage fault 14H EEPROM operation

（Lv） fault（EEP）

09H 15H PID feedback fault

（LP）
Iutput phase loss
（PIDE）

0AH 16H-1BH Reserved

Output short-circuit（SC）

0BH 1CH Output phase loss

Over-heat（OH1）
（SPO）

-211-
 ASCII mode RTU mode

STX ‘:’ Address 01H

‘0’ Function 86H
Address
‘1’ Fault 50H
‘8’ address 01H
Function
‘6’ Fault code 01H
‘5’ CRC CHK Low F0H
Fault ‘0’ CRC CHK High C9H
address ‘0’
‘1’
‘0’
Fault code
‘1’
‘2’
LRC Check
‘7’
CR
END
LF

-212-
 00H No fault

01H Command code error

02H Illegal address

03H Illegal data

04H ~ 05H Reserved

06H Inverter is busy

Communication
5001H 07H ~ 09H Reserved
fault address

10H Password error

11H Check error

12H Invalid modified

parameters

13H System locked

14H Illegal of data number

-213-
-214-