Scribd
Upload
373 views34 pages

Maintenance and Repair Strategies: Unit 1

The document discusses maintenance, repair, and rehabilitation strategies for structures. It outlines the key steps in assessing damaged structures which include physical inspection, documentation of damages, testing, structural analysis, and determining appropriate remedial measures. The causes of deterioration like corrosion, environmental effects, poor quality materials, and construction flaws are also explained. The document also covers types of maintenance, inspection of structures, investigation of life cycles, defects in concrete and steel, classification of cracks, and methods of repair.

Uploaded by

selva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
373 views34 pages

Maintenance and Repair Strategies: Unit 1

The document discusses maintenance, repair, and rehabilitation strategies for structures. It outlines the key steps in assessing damaged structures which include physical inspection, documentation of damages, testing, structural analysis, and determining appropriate remedial measures. The causes of deterioration like corrosion, environmental effects, poor quality materials, and construction flaws are also explained. The document also covers types of maintenance, inspection of structures, investigation of life cycles, defects in concrete and steel, classification of cracks, and methods of repair.

Uploaded by

selva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 34

MAINTENANCE

AND REPAIR
STRATEGIES
UNIT 1
Maintenance

 Maintenance is the act of keeping something in good


condition by checking or repairing it regularly.
Repair

 Repair is the process of restoring something that is


damaged or deteriorated or broken, to good condition.
Rehabilitation

 Rehabilitation is the process of returning a building or an


area to its previous good conditions.
Two facets of maintenance

 The two facets of maintenance are


 i) Prevention
 ii) Repair
Assessment procedure for evaluating a damaged structure
i. Physical Inspection of damaged structure.
ii. Preparation and documenting the damages.
iii. Collection of samples and carrying out tests both in situ and in laboratory.
iv. Studying the documents including structural aspects.
v. Estimation of loads acting on the structure
vi. Estimation of environmental effects including soil structure interaction.
vii. Diagnosis
viii. Taking preventive steps not to cause further damage
ix. Retrospective analysis to get the diagnosis confirmed
x. Assessment of structural adequacy
xi. Estimation on future use
xii. Remedial measures necessary to strength and repairing the structure.
xiii. Post repair evaluation through tests
xiv. Load test to study the behavior
xv. Choice of course of action for the restoration of structure.
A simple flow chart incorporating the
above points in presented in Figure
The causes of deterioration

i) Deterioration due to corrosion


ii) Environmental effects
iii) Poor quality material used
iv) Quality of supervision
v) Design and construction flaws
Design and construction flaws

 Design of concrete structures governs the performance of


concrete structures.

 Well designed and detailed concrete structure will show


less deterioration in comparison with poorly designed and
detailed concrete, in the similar condition.

 The beam-column joints are particularly prone to defective


concrete, if detailing and placing of reinforcement is not
done properly.

 Inadequate concrete cover may lead to carbonation depth


reaching up to the reinforcement, thus, increasing the risk
of corrosion of the reinforcement.
Environmental effects

 Micro-cracks present in the concrete are the sources of


ingress of moistures atmospheric carbon di-oxide into
the concrete which attack reinforcement and with
various ingredients of concrete.

 In aggressive environment concrete structure will be


severely reduces.
Poor quality material used

 Quality of materials, to be used in construction, should be


ensured by means various tests as specified in the IS codes.

 Alkali-aggregate reaction and sulphate attack results in


early deterioration.

 Clayey materials in the fine aggregates weaken the mortar


aggregate bond and reduce the strength.

 Salinity causes corrosion of reinforcing bars as well as


deterioration of concrete.
Quality of supervision

 Construction work should be carried out as per the laid


down specification.

 Adherence to specified water-cement ratio controls


strength, permeability durability of concrete.

 Insufficient vibration may result in porous and honey


combined concrete, whereas excess vibration may cause
segregation.
Deterioration due to corrosion

 Spelling of concrete cover

 Cracks parallel to the reinforcement

 Spelling at edges

 Swelling of concrete

 Dislocation

 Internal cracking and reduction in area of steel


reinforcement.
Physical inspection of damaged structure

 Some of the use full in formation may be obtained from the

 physical inspection of damaged structure, like nature of distress, type of


distress, extent damage and its classification etc,

 their causes preparing and documenting the damages,

 collecting the samples for laboratory testing and analysis, planning for in situ
testing,

 special environmental effects which have not been considered at the design
stage and

 information on the loads acting on the existing structure at the time of damage
may be, obtained.

 To stop further damages, preventive measure necessary may be planned which


may warrent urgent execution.
The steps in selecting a repair procedure
 Consider total cost
 Do repair job in time
 If defects are few & isolated repair on an individual basis.
 Otherwise do in generalized manner
 Ensure the repair prevents further development of defects
 Incase of lost strength, repairs should restore the strength
 If appearance is a problem, the number of applicable types of repairs become
limited & the repairs must be covered
 Repair works should not interface with facilities of the structure
 Take care in addition of section to a member and in redistributing live loads and
other live load moments.
 After selecting a suitable method of repairs, and after considering all the
ramifications of its application, the
 last step is to prepare plans & specification and proceed with the work.
The cause for deterioration of concrete structure

a) Inspect & observe the structure


b) Observe in bad & good weather
c) Compare with other constructions on the area or
elsewhere & be patient
d) Study the problem & allow enough time to do the job
The factors to be considered by the designer at the
construction site

 Minimum and maximum temperatures


 temperature cycles
 exposure to ultra violet radiation
 amount of moisture
 wet/dry cycles
 presence of aggressive chemicals
The steps in repair aspect

i. finding the deterioration

ii. determining the cause

iii. evaluating the strength of existing building or structure

iv. evaluating the need of repair

v. Selecting & implementing a repair procedure


The repair aspect of maintenance.

1. finding the deterioration


2. determining the cause
3. evaluating the strength of existing building or structure
 Fixed percentage method
 Analysis of the Actual stress condition
 Load test
4. evaluating the need of repair
5. Selecting & implementing a repair procedure.
The prevention aspect of maintenance.

 Of the two considerations – prevention & repair, prevention is more

important.

 These 3 points : proper materials

proper details

proper construction

require knowledge of what is improper at a site or construction; about the

various ways of

 deterioration and about their causes.

 But these are some general considerations that should be taken into

account for both the construction of new concrete structures and the

repair of deteriorated structures. They are as follows


The following factors should be considered by the designer at the
construction site.
 Minimum and maximum temperatures
 temperature cycles
 exposure to ultra violet radiation
 amount of moisture
 wet/dry cycles
 presence of aggressive chemicals
 Combine only materials with similar properties
 Assess the limitations of a particular material in its functional context.
 Protect materials from general deterioration
 Design level Factors
TYPES OF MAINTENANCE

 Planned schedule maintenance (planned well in advance)

 Preventive maintenance(planned to protect preventing failure)

 Condition based maintenance(work done after inspection)

 Fixed time maintenance(done at interval of time)

 Opportunity maintenance(work when possible within the limits

of operational demand)

 Routine maintenance(daily, weekly etc.,)

 Shutdown maintenance(maintenance after demolition)

 Emergency maintenance(unexpected failure after natural

calamities)
INSPECTION OF STRUCTURES

o Collection of data for investigation


o Study of documents related to structures
o Preliminary inspections such as spalling , deflections.
o Detailed inspection
 Field testing
 Laboratory testing
o Structural analysis of buildings
o Assessment of structures
o Repair options
 Non repair
 Aesthetic repair
 Structural repair
 Replacement
ASPECTS OF INSPECTION IN ONGOING SITE

 Spot inspection
 Progress inspection
 Periodic inspection
 Inspection by clerk of work
 Full time inspection

ASPECTS OF INSPECTION IN EXISTING SITE

 Initial inspection
 Routine inspection
 Event driven inspection
 In depth inspection
 Special inspection
Steps in inspection and repair of concrete
structures
The following items are more important when making these
inspections:

 Reasons for conducting inspections

 Preliminary inspections

 Detailed inspections
Investigation of life cycle for a structure
Various aspects of investigation in on going site
 Spot inspection
 Progress inspection
 Periodic inspection
 Inspection by clerk of the work
 Full time inspection
Various aspects of investigation in existing site
 Initial inspection
 Routine inspections
 Event driven inspection (include photos, load rating, repair
recommendations, loads restrictions)
 In depth inspections
 Special inspections
Types of defects
Defects in concrete
 Cracking
 Spalling
 Disintegration
Defects in steel
 Rusting
 Corrosion
 Buckling
 Bearing failure
 Defects by weld and rivets
Spalling of concrete
Disintegration in concrete structures
Classification of cracks

Cracks based on their width

 Fine less than 0.1 mm

 Thin 0.1 t0 0.3 mm

 Medium 0.3 to 0.7 mm

 Wide 0.7 to 2.0 mm

 Very wide greater than 2 mm


Methods of repair of cracks

 Non structural or surface cracks

 Very heavy cracks

 RCC band (crack arrestor)

 Cracks over arch openings

 Stitching

 Cracks at RCC and masonry walls


Repair for strengthening of RCC structural members
 Cracks in RCC member – by adding reinforcing steel with proper
key and bonding with old member.
 Cracks due to shear – occurs 45 degree to the axis of members and
corrected by adding diagonal shear rft. In the form of dowels.
 Cracks at support or at mid – span bottom – occurs due to
insufficient steel and they are corrected by adding required nos. of
steel.
 Pressure grouting – cement slurry or admixtures are applied with
high pressure.
 Cracks in foundations due to settlement – cured by grouting method
by increasing the bearing capacity of soil.

You might also like