Subject - Strength of Materials

ID
Questio Hooke's law holds good up to..
n
A yield point
B Proportional limit
C plastic limit
D breaking point
Answer B
Marks 1
Unit A1

ID
Questio The ratio of linear stress to linear strain is called as
n
A modulus of elasticity
B modulus of rigidity
C Bulk modulus
D Poisson's ratio
Answer A
Marks 1
Unit A1
ID
Questio The modulus of elasticity for mild steel is approximately equal to
n
A 80 kN/mm2
B 100 kN/mm2
C 110 kN/mm2
D 210 kN/mm2
Answer D
Marks 1
Unit A1

ID
Questio When the material is loaded with elastic limit , then the stress is ……. to
n strain.
A equal
B directly proportional
C inversely proportional
D not equal
Answer B
Marks 1
Unit A1
ID
Questio The ratio of ultimate tensile stress to the design stress is known as
n
A elastic limit
B strain
C factor of safety
D bulk modulus
Answer C
Marks 1
Unit A1

ID
Questio An aluminum member is designed based on
n
A yield stress
B elastic limit stress
C proof stress
D ultimate stress
Answer A
Marks 1
Unit A1

ID
Questio The poisson's ratio for Cast Iron varies from
n
A 0.25 to 0.33
B 0.21 to 0.25
C 0.23 to 0.27
D 0.33 to 0.38
Answer C
Marks 1
Unit A1

ID
Questio The Poisson’s ratio for steel varies from
n
A 0.21 to 0.25
B 0.25 to 0.33
C 0.33 to 0.38
D 0.38 to 0.45
Answer B
Marks 1
Unit A1

ID
Questio The property of material to absorb shock energy without failure is known
n as….
A Elasticity
B Toughness
C Stiffness
D Resilience
Answer B
Marks 1
Unit A1
ID
Questio Young’s modulus of Elasticity for perfectly rigid body is….
n
A Zero
B unity
C infinity
D none of these
Answer C
Marks 1
Unit A1

ID
Questio The stress is….
n
A Scalar
B Vector
C Tensor
D None of the above
Answer C
Marks 1
Unit A1

ID
Questio The Poisson’s ratio for perfectly rigid body is
n
A 1
B 0
C -1
D 0.5
Answer B
Marks 1
Unit A1
ID
Questio Shearing strain is represented by………
n
A angle of twist
B angle of shear
C deforming force
D deforming torque
Answer B
Marks 1
Unit A1
ID
Questio Greater the value of modulus of elasticity more…is the material
n
A plastic
B elastic
C brittle
D ductile
Answer B
Marks 1
Unit A1
ID
Questio Stress does not depand upon
n
A applied force
B area of c/s
C modulus of elasticity
D none
Answer C
Marks 1
Unit A1
ID
Questio stress does not depend upon
n
A applied force
B area of c/s
C change in length
D none
Answer C
Marks 1
Unit A1
ID
Questio modulus of elasticity for rubber is ……than that for steel.
n
A larger than
B equal to
C smaller than
D Any of the above
Answer C
Marks 1
Unit A1
ID
Questio Change in length of the rod due to change in temperature depends on…
n
A original length
B change in temperature
C coefficient of thermal expansion
D all of above
Answer D
Marks 1
Unit A1
ID
Questio The value of K for perfectly rigid body is
n
A zero
B 1
C -1
D Infinity
Answer D
Marks 1
Unit A1
ID
Questio Time dependent permanent deformation is called as
n
A Plastic deformation
B Elastic deformation
C Creep
D An elastic deformation
Answer C
Marks 1
Unit A1
ID
Questio Figure out the odd point in the following
n
A Proportional limit
B Elastic limit
C Yield point
D Fracture point
Answer D
Marks 1
Unit A1
ID
Questio Engineering stress strain curve and true stress strain curve are equal up to
n
A Proportional limit
B Elastic limit
C Yield point
D Tensile strength point
Answer C
Marks 1
Unit A1
ID
Questio Shape of true stress strain curve of material depends upon
n
A Strain
B Strain rate
C Temperature
D All of the above
Answer D
Marks 1
Unit A1
ID
Questio Within elastic limit in a loaded material, stress is
n
A inversely proportional to strain
B directly proportional to strain
C equal to strain
D none of the above
Answer B
Marks 1
Unit A1
ID
Questio The ratio of linear stress to linear strain is known as
n
A Poisson's ratio
B bulk modulus
C modulus of rigidity
D modulus of elasticity
Answer D
Marks 1
Unit A1
ID
Questio the ratio of lateral strain to linear strain is known as
n
A Poisson's ratio
B bulk modulus
C modulus of rigidity
D modulus of elasticity
Answer A
Marks 1
Unit A1
ID
Questio The ratio of shear stress to shear strain is known as
n
A Poisson's ratio
B bulk modulus
C modulus of rigidity
D modulus of elasticity
Answer C
Marks 1
Unit A1
ID
Questio The ratio of normal stress of each face of a solid cube to volumetric strain is
n called
A Poisson's ratio
B bulk modulus
C modulus of rigidity
D modulus of elasticity
Answer B
Marks 1
Unit A1
ID
Questio Hooke's law holds good up to
n
A Proportional limit
B yield point
C elastic limit
D plastic limit
Answer A
Marks 1
Unit A1
ID
Questio The property of material by virtue of which a body returns to its original
n shape after removal of load is known as
A ductility
B plasticity
C elasticity
D resilience
Answer C
Marks 1
Unit A1
ID
Questio The work done in producing strain on a material per unit volume is called
n
A resilience
B ductility
C elasticity
D plasticity
Answer A
Marks 1
Unit A1
ID
Questio The property of material by virtue of which a material can be beaten into
n plates is called
A ductility
B malleability
C resilience
D plasticity
Answer B
Marks 1
Unit A1
ID
Questio The Combined effect of external forces acting on body is called
n
A Stress
B Strain
C Load
D None
Answer C
Marks 1
Unit A1
ID
Questio ………….Load is one which is considered to act at a point.
n
A Triangular
B Uniformly Distributed Load
C Point
D None
Answer C
Marks 1
Unit A1
ID
Questio The internal resistance which the body offers to meet the load or external
n force is called
A stress
B strain
C pressure
D None
Answer A
Marks 1
Unit A1
ID
Questio The Unit of stress in SI unit is
n
A MN/mm2
B kN/mm2
C N/mm2
D All of above
Answer D
Marks 1
Unit A1
ID
Questio ……….represents the resistance developed by a unit area of cross section.
n
A Unit stress
B Total stress
C either of above
D All of above
Answer A
Marks 1
Unit A1
Questio Simple stress is often called
n
A Direct Stress
B Transverse Stress
C Total Stress
D Any of above
Answer A
Marks 1
Unit A1
ID
Questio The deformation per unit length is called……….
n
A Strain
B tensile stress
C compressive stress
D shear stress
Answer A
Marks 1
Unit A1
ID
Questio If L and dL are are length and change in length respectively, then strain is
n equal to
A dL/L
B L/dL
C LxdL
D None
Answer A
Marks 1
Unit A1
ID
Questio If V is the volume of a rectangular bar subjected to a three
n dimensional stress state and the Poisson's ratio for the material
is 0.5, the change in volume of the bar will be ___________.
A V
B 2V
C 0.5V
D 0
Answer D
Marks 1
Unit A1
ID
Questio For material Poisson’s ratio is 0.25. Relation between E and G will be
n
A 0
B 2G
C 3G
D 2.5G
Answer D
Marks 1
Unit A1
ID
Questio The modulus of elasticity of a material is 210 GPa and its Poisson's
n ratio is 0.4. The modulus of rigidity of the material is
A 210
B 75
C 350
D 300
Answer B
Marks 1
Unit A1
ID
Questio The value of factor of safety is always
n
A >1
B <1
C =1
D =0
Answer A
Marks 1
Unit A1
ID
Questio The value of margin of safety is always
n
A >1
B <1
C =1
D >0
Answer D
Marks 1
Unit A1
ID
Questio If the working load is one third of the ultimate load, the factor of
n safety is
A 0.333
B 3
C 2
D 1
Answer B
Marks 1
Unit A1
ID
Questio If 1 is subtracted from the ratio of yield stress to working stress
n the quantity obtained is known as
A margin of safety
B F.O.S.
C modulus of elasticity
D none of the above
Answer A
Marks 1
Unit A1
ID
Questio Stress does not depend upon
n
A applied force
B area of c/s
C change in length
D none of the above
Answer C
Marks 1
Unit A1
ID
Questio Stress does not depend upon
n
A applied force
B area of c/s
C modulus of elasticity
D none of the above
Answer C
Marks 1
Unit A1
ID
Questio A metal plate of length L and width b has a circle drawn on it. If it
n is subjected to a compressive stress acting along its width, the circle
will
A remain circle of same radius
B become ellipse with major axis along its width
C become ellipse with major axis along its length
D become circle of smaller radius
Answer C
Marks 1
Unit A1