TECHNICAL DATA SHEET | SECTION 4.

3
PolyЯRon CURE AC
Built to last

PolyЯRon CURE AC
Polymer based concrete curing compound and sealer

Description
PolyЯRon CURE AC is a polymer modified
water based emulsion concrete curing
compound. When applied to newly poured
concrete it dries fast to form a film with low water
vapour permeability. By reducing evaporation
from the concrete surface, the water necessary
for cement hydration is maintained. This allows
the maximum development of compressive and
tensile strength in the finished concrete and
results in a more durable surface with lower
permeability. Physical properties
Advantages Form Liquid
• Single component system and easy to Colour White
apply. Specific gravity 1.01±0.005 @ 250C
• Non flammable and non-toxic. Moisture Retention
<0.55kg/m2
• Forms stable film on the surface to ASTM C 156
provide excellent curing and sealing Toxicity Non – Toxic
properties.
Drying time <4 hours
• Non-staining.
• Considerable reduction in loss of water VOC <20g/l
from concrete.

Built to last
Coverage
Application area PolyЯRon CURE AC provides coverage of 6.0 to 7.0
PolyЯRon CURE AC is a high quality curing and m2.per litre
sealing compound suitable for use on all
concrete surfaces. All exposed elements of a Application Guidelines
structure subject to water loss due to Mixing
evaporation will benefit from treatment. These PolyЯRon CURE AC is a ready to use material. It
include floor slabs, columns, beams, walls, should be stirred well before use.
precast panels etc.
• Suitable for all kinds of concrete. Application method
• Horizontal and vertical applications. PolyЯRon CURE AC can be applied by brush, roller or
spray. Application tools must be free of any other
Compliance previously applied material. Aim for an even film and avoid
Clear upon drying: pinholes which can allow undesirable moisture loss.
PolyЯRon CURE AC complies with ASTM Uniform application is best obtained by spraying half the
C309 Type1. recommended quantity in one direction over the whole
White Pigmented: work and the remainder at right angles to the original
PolyЯRon CURE AC complies with ASTM coating.
C309 Type2.
Complies with QATAR CONSTRUCTION
STANDARDS

HPI/TDS/1912-4.3A

HP INDUSTRIES W.L.L
Street no.1,New Industrial Zone,Doha-Qatar, IAS0310Q1101

Phone:+974 44433381, Fax:+974 44433382,

IAS0310E1102
SECTION 4.3
Email:[email protected] / [email protected]
ACCREDITED
TM

Website:www.hpiqatar.com IAS0310Q1103 Management System

Cer�fica�on Body
MSCB-178

89
Apply to exposed concrete surfaces as soon as Shelf life
the sheen of moisture brought to the surface by PolyЯRon CURE AC has a shelf life of 12 months in un-
final screeding or trowelling has disappeared, opened packs and if stored in accordance with our
but while the concrete is still damp.If brushes instructions.
are used and the concrete is still wet enough to
be marked by the brush it is too early to apply Storage
the curing compound. This timing is important PolyЯRon CURE AC should be stored under enclosed
for satisfactory curing. shaded area at temperatures between 5 – 350C.

If a delay is unavoidable moisten the concrete Precautions

by light spraying until the surface will not readily • Subsequent coatings should not be applied over
absorb more water, allow the sheen to PolyЯRon CURE AC without checking with the
disappear and apply PolyЯRon CURE AC. manufacturer or supplier of the coating system for
Saw cuts should be treated with PolyЯRon compatibility.
CURE AC immediately after cutting as • In case of non compatibility with subsequent
significant moisture loss can occur in these coating, wear off the curing membrane using
areas. Check for compatibility with joint commercial floor scrubber or by using synthetic
sealants, if they are to be used later. abrasive pad or any other means to ensure
adequate bonding of successive coating
For curing previously boxed columns etc, spray
with water as soon as formwork is removed and
Health & safety
then apply PolyЯRon CURE AC.
PolyЯRon CURE AC should not come in contact with
Note: The spray equipment must be capable to
eyes or be swallowed. Ensure adequate ventilation and
generate a fine mist causing no damage to wet
avoid
concrete surface.
inhalation of vapours. Applicator should wear appropriate
Subsequent Finishes clothes, gloves and goggles. Use of barrier cream is
The resin used in PolyЯRon CURE AC allows recommended to provide additional skin protection. If
direct application of many floor coverings and comes in contact with eyes flush with plenty of fresh water
paint systems, as given typically below: and seek medical advice.
• Water based emulsion paints containing PVA,
PVC, acrylic copolymers, etc.
• Bituminous emulsions and solutions
• Thin section polymer modified cement
Built to last
Refer Material Safety Data Sheet for further details.

Fire
systems Non- flammable

• Epoxy resin and polyurethane coatings which More from our product Range
do not rely on penetration for substrate bond A Broad range of construction chemical products are
• Modified and unmodified cementitious mortar manufactured by HP Industries under PolyЯRon brand
• Water and solvent based acrylic coatings which include:
• Concrete admixtures
Cleaning • Waterproofing and dampproof coatings
Clean up equipment with water and detergent • Bituminous coatings and Primers
before product dries. Keep sprayer nozzles • Surface treatments and releasing agents
dipped in water between spraying operations, • Floorings, toppings and coatings
then clean completely once finish • Protective coatings& sealers
.
• Tile glues, block fixing agents & grouts
Packaging • Structural Grouts &Anchors
PolyЯRon CURE AC is available in 20litre pails
• Adhessives and bonding agents
and 200 litre drums.
• Concrete repair materials
• Joint sealants & Moulding compounds
• XPS Thermal Insulation boards
Note : The technical specification, information and recommendation given are of general nature, based on the current technical knowledge and the user or his representative is
recommended to check suitability of the product. HPI requires the right to amend the technical details of the product as part of the ongoing research and development. As the work
execution is beyond the direct and continuous control of HPI no guarantee or responsibility is assumed on the performance of work completion executed with the use of our product.

HPI/TDS/1912-4.3A

HP INDUSTRIES W.L.L
Street no.1,New Industrial Zone,Doha-Qatar, IAS0310Q1101

Phone:+974 44433381, Fax:+974 44433382,

IAS0310E1102
SECTION 4.3
Email:[email protected] / [email protected]
ACCREDITED
TM

Website:www.hpiqatar.com IAS0310Q1103 Management System

Cer�fica�on Body
MSCB-178

90