Scribd
Upload
176 views

Simple Free-Energy Devices: Chapter 23: Power From Inertia

This document discusses Chas Campbell's flywheel system for generating free energy. It uses a mains motor to spin a flywheel connected to an electrical generator. When the flywheel reaches optimum speed, the motor is powered by the generator's output instead of the mains, creating a self-powered system. The flywheel's constant inward acceleration as it spins provides a continuous inflow of energy from gravity. Jacob Byzehr later analyzed such systems and found the ratio between the driving and take-off pulley diameters on the flywheel shaft is important, with the driving pulley needing to be 3-4 times larger for high performance. A video shows such a system generating over twice the output power as its input.

Uploaded by

Luc Ber
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
176 views

Simple Free-Energy Devices: Chapter 23: Power From Inertia

This document discusses Chas Campbell's flywheel system for generating free energy. It uses a mains motor to spin a flywheel connected to an electrical generator. When the flywheel reaches optimum speed, the motor is powered by the generator's output instead of the mains, creating a self-powered system. The flywheel's constant inward acceleration as it spins provides a continuous inflow of energy from gravity. Jacob Byzehr later analyzed such systems and found the ratio between the driving and take-off pulley diameters on the flywheel shaft is important, with the driving pulley needing to be 3-4 times larger for high performance. A video shows such a system generating over twice the output power as its input.

Uploaded by

Luc Ber
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Simple Free-Energy Devices

There is nothing magic about free-energy and by “free-energy” I mean something which produces
output energy without the need for using a fuel which you have to buy.

Chapter 23: Power From Inertia


Chas Campbell’s Flywheel System.
Recently, Mr. Chas Campbell of Australia demonstrated electrical power gain with a flywheel system
which he developed. Esentially, he spins a mains motor, gears it appropriately through a drive train
which includes a ten kilogram flywheel so that it spins an AC generator at it’s optimum speed of just
over three thousand revs per minute. When the system is running at full speed, Chas switches the
mains motor over so that it is powered by the output of the generator. This works very well and allows
his self-powered system to power other tools like drills. This is the arrangement:

Let me explain the overall system. A mains motor of 750 watt capacity (1 horsepower) is used to drive
a series of belts and pulleys which form a gear-train which produces over twice the rotational speed at
the shaft of an electrical generator. The intriguing thing about this system is that greater electrical
power can be drawn from the output generator than appears to be drawn from the input drive to the
motor. How can that be? Well, although it does not appear to be widely known, the rim of a rotating
flywheel is considered to be continuously accelerating inwards towards the axle. That constant
acceleration produces an inflow of energy from the gravity field into the system. The important point is
that Chas Campbell’s system is self-powered and can power other equipment as well.

Now take a look at the construction which Chas has used:

23 - 1
You notice that not only does he have a heavy flywheel of a fair size, but that there are three or four
other large diameter discs mounted where they also rotate at the intermediate speeds of rotation. While
these discs may well not have been placed there as flywheels, nevertheless, they do act as flywheels,
and each one of them will be contributing to the free-energy gain of the system as a whole. A video of a
neat replication, with 750 watts input power and 2340 watts of output power is here:
http://www.youtube.com/watch?v=98aiISB2DNw and this implementation does not appear to have a
heavy flywheel as you can see from this picture, although the largest pulley wheel looks as if it contains
considerable weight:

Jacob Byzehr’s Analysis.


In 1998, Jacob lodged a patent application for a design of the type shown by Chas Campbell. Jacob
has analysed the operation and he draws attention to a key design factor:

23 - 2
Jacob states that a very important feature for high performance with a system of this kind is the ratio of
the diameters of the driving and take-off pulleys on the shaft which contains the flywheel, especially with
systems where the flywheel rotates at high speed. The driving pulley needs to be three or four times
larger than the power take-off pulley. Using Chas’ 1430 rpm motor and a commonly available 1500 rpm
generator, the 12:9 step-up to the shaft of the flywheel gives a satisfactory generator speed while
providing a 3.27 ratio between the 9-inch diameter driving pulley and the 2.75” diameter power take-off
pulley. If a generator which has been designed for wind-generator use and which has it’s peak output
power at just 600 rpm is used, then an even better pulley diameter ratio can be achieved.

Patrick J Kelly
www.free-energy-info.tuks.nl
www.free-energy-info.com
www.free-energy-devices.com

23 - 3

You might also like