Mechanical pressure switch

Relative pressure switch

Type 620/625

Type 620 and 625 pressure switches, with 13 pressure ranges,

are suitable for liquids and gases. Body materials are available in
plastic, brass and aluminium, with a choice of NBR, FPM, EPDM
and silicone diaphragms.
Very high precision through finely tuned measurement stages
and high long term stability. Rugged design and especially suit-
able for use in general industrial equipment
construction, process technology and food automation.

Pressure range + High accuracy by 13 ideally designed pressure range

-4 ... -900 mbar / increments
+ Switching differences adjustable
2 ... 6000 mbar + High long term stability with repro-ducibility of switching
points < ± 0.3 mbar
+ Customer specific switching points adjustable in factory
+ Rugged industrial switch with excellent Price /
performance ratio

Pressure and flow Huba Control Type 620/625 | Technical data subject to change | Edition 09/2020 1/5
 Technical overview
Pressure range
Relative 2 ... 6000 mbar
Negative -4 ... -900 mbar

Operating conditions
Medium Liquids and nuetral gases
NBR based 0 ... +80 ºC
FPM -10 ... +80 ºC
EPDM -10 ... +80 ºC
Temperature
Q (Silicone) -40 ... +80 ºC
Ambient +65 ºC
Storage -40 ... +80 ºC
Tolerable overload See order code selection table
Lowest turn-on pressure 2 mbar
Lowest swiching difference 1 mbar

Materials
Case Fibreglass reinforced plastic
NBR based
EPDM
Diaphragm FPM
Silicone
Materials in contact with the medium Base type 620 ABS or PA
Base type 625 Aluminium, nickel plated brass
X 5 CrNi 18-10, 1.4301
Other components
Polyacetate (only at negative)

Electrical overview
Nominal voltage 250 VAC
Nominal current for resistive loading 1A 6A
Nominal current for motor loading 0.5 A 3A
Contact system Changeover contact
Service life Mechanically 106 switching cycle 1)

Protection standard
Without cover IP 00
With cover 2) IP 54

Repeatability
±5% of the switching point With diaphragm NBR based / Silicone minimum ±0.3 mbar
±10% of the switching point With diaphragm FPM / EPDM minimum ±0.6 mbar

Electrical connections
Screw terminals (Option)
Tab connectors (AMP) 6.3 mm
Cable gland PG 11 with cover

Pressure connections
Inside / outside thread M5 / M12x1
Type 620
Connection pipe / thread Ø 6 mm / M12x1
Type 625 Thread with counternut M12x1 (CuZn nickel plated), G ⅛, G ¼

Installation arrangement
For switching points calibrated in the factory Indicate installation arrangement.
Remark: By changing the mounting position the switching points also change. The adjustment ranges are in relation with the mounting position.

Weight
Type 620 ~ 70 g
with aluminium base ~ 100 g
Type 625
with base brass ~ 200 g

Packaging
Single packaging in cardboard
Multiple packaging in cardboard per 18 pcs.

Legend to cross-section drawing

1 Switching point setting

2 AMP tab connectors
3 Switching difference setting
4 Compression spring
5 Changeover contact
6 Contact element
7 Diaphragm

1)
The permitted switching difference has to be respected 2)
For installation arrangement electrical connections upward

2/5 Pressure and flow Huba Control Type 620/625 | Technical data subject to change | Edition 09/2020
 1 2 3 4 5

Order code selection table 620. X X X X X

p max. pt 2) Switching capacity 250 VAC
2 ... 8 mbar 30 mbar 50 mbar 1A 9 1
6 ... 75 mbar 300 mbar 500 mbar 1A 9 2
Pressure range 1)
12.5 ... 80 mbar 300 mbar 500 mbar 6A 9 3
12.5 ... 200 mbar 300 mbar 500 mbar 1A 9 4
25 ... 220 mbar 300 mbar 500 mbar 6A 9 5
ABS ... +70 ºC 0
Hose connection Ø 6 mm and M12x1
Pressure connection / PA 66 ... +80 ºC 1
pressure case ABS ... +70 ºC 2
Inside thread M5 and M12x1
PA 66 ... +80 ºC 3
NBR based 0
FPM 2
Diaphragm material
EPDM 4
Q (Silicone) 6
Two factory set switching points (please specify on order) W
Switching points (optional) One factory set switching point high (please specify on order) R
One factory set switching point low (please specify on order) U

1 2 3 4 5

Order code selection table 625. X X X X X

Relative 9
Pressure mode
Negative 6
p max. pt 2)
Switching capacity 250 VAC
2 ... 8 mbar 30 mbar 50 mbar 1A 9 0
6 ... 75 mbar 300 mbar 500 mbar 1A 9 1
12.5 ... 80 mbar 300 mbar 500 mbar 6A 9 2
12.5 ... 200 mbar 300 mbar 500 mbar 1A 9 3
25 ... 220 mbar 300 mbar 500 mbar 6A 9 4
80 ... 2000 mbar 6000 mbar 10000 mbar 1A 9 5
Pressure range 1) 120 ... 2200 mbar 6000 mbar 10000 mbar 6A 9 6
1000 ... 6000 mbar 6800 mbar 10000 mbar 6A 9 7

-4 ... -30 mbar -50 mbar -100 mbar 1A 6 1

-15 ... -80 mbar -300 mbar -500 mbar 1A 6 2
-30 ... -150 mbar -300 mbar -500 mbar 6A 6 3
-50 ... -600 mbar -1000 mbar -1000 mbar 6A 6 4
-100 ... -900 mbar -1000 mbar -1000 mbar 6A 6 5
Aluminium 1
G⅛
Brass B
Pressure connection / M12x1 Aluminium 2
pressure case Brass 3
G¼ Aluminium 4
Nickel plated brass 5μm A
NBR based 0
FPM 2
Diaphragm material
EPDM 4
Q (Silicone) 6
Two factory set switching points (please specify on order) W
Switching points (optional) One factory set switching point high (please specify on order) R
One factory set switching point low (please specify on order) U

Accessories 3) Order number

Cover of PG11 on the side 105836
Mounting bracket with hole Ø 12.5 mm for M12 104259
Mounting bracket with hole Ø 14 mm for G ¼ 102872
Connector set (Tab connectors AMP) 103479
Screw clamps set 103491
Calibration certificate 104551

1)
Other pressure ranges on request 2)
pt = test pressure 3)
Accessories supplied loose

Pressure and flow Huba Control Type 620/625 | Technical data subject to change | Edition 09/2020 3/5
 Dimensions in mm / Electrical connections

L
X
X L
G¼ 16
G⅛ 16
M12X1 14

1 Feeder (COM) For vacuum:

2 NC contact 3 - NC contact
3 NO contact

Setting ranges

2 ... 8 mbar 6 ... 75 mbar 12.5 ... 80 mbar 12.5 ... 200 mbar 25 ... 220 mbar
A A A A A
B B B B B

80 ... 2000 mbar 120 ... 2200 mbar 1000 ... 6000 mbar – 4 ... – 30 mbar – 15 ... – 80 mbar
A A A A A
B B B B B

– 30 ... – 150 mbar – 50 ... – 600 mbar – 100 ... – 900 mbar
A A A
B B B

A Upper switching point (mbar)

B Distance between contacts

4/5 Pressure and flow Huba Control Type 620/625 | Technical data subject to change | Edition 09/2020
Huba Control AG
Headquarters Schweiz
Industriestrasse 17
CH-5436 Würenlos
Telefon +41 56 436 82 00
Fax +41 56 436 82 82
[email protected]

Huba Control AG Huba Control AG

Niederlassung Deutschland Vestiging Nederland
Schlattgrabenstrasse 24 Hamseweg 20A
D-72141 Walddorfhäslach NL-3828 AD-Hoogland
Telefon +49 7127 2393 00 Telefoon +31 33 433 03 66
Fax +49 7127 2393 20 Telefax +31 33 433 03 77
[email protected] [email protected]

Huba Control SA Huba Control AG

Succursale France Branch Office United Kingdom
Rue Lavoisier Unit 13 Berkshire House, County Park
Technopôle Forbach-Sud Business Centre, Shivenham Road
F-57602 Forbach Cedex Swindon - Wiltshire SN1 2NR
Téléphone +33 3 87 84 73 00 Phone +44 1993 77 66 67
Télécopieur +33 3 87 84 73 01 Fax +44 1993 77 66 71
[email protected] [email protected]

www.hubacontrol.com