Doc. No.

: 26071-203-V66A-MTFR-20044

Job No. : 26071 Rev.00D

WELDING MAP & NDE MAP FOR SHOP

FABRICATED
(AT KDM SHOP KOREA)
LPG TANK (D-320-06A/B)

PROJECT : Engineering, Procurement and Construction (EPC) Inside

Battery Limits (ISBL) and Outside Battery Limits (OSBL) for
the Refinery Development Master Plan (RDMP) Project
RU V Balikpapan
LOCATION : Refinery Unit V Balikpapan, East Kalimantan,Indonesia
OWNER : PT PERTAMINA (Persero)
PO NO. : 26071-120-PO-MTFR-00066

00D 18 JAN 21 RE-ISSUED FOR REVIEW

J.H.CHOI K.J.CHOI ABDUL ROCHIM
00C 12 JAN 21 RE-ISSUED FOR REVIEW J.H.CHOI K.J.CHOI FAUZAN RUMZI

00B 04 JAN 21 RE-ISSUED FOR REVIEW J.H.CHOI K.J.CHOI HENRY SIANTURI

00A 27 OCT 20 ISSUED FOR REVIEW J.H.CHOI K.J.CHOI HENRY SIANTURI

REV. DATE DESCRIPTION PREPARED CHECKED APPROVED

1 of 11
 Doc. No. : 26071-203-V66A-MTFR-20044

Job No. : 26071 Rev.00D

REVISION LOG

REV. NO. DATE PAGE DESCRIPTION

00A 27 OCT 20 - ISSUED FOR REVIEW

00B 04 JAN 21 4-11 Revised Map and Add of List Weld Map
Change for Welding Map and Welding Map
00C 12 JAN 21 1-10
Summary
Change for Welding Map and Welding Map in
00D 18 JAN 21 1-11
Summary color

2 of 11
 Doc. No. : 26071-203-V66A-MTFR-20044
B

Job No. : 26071 Rev.00D

Table of Contents 
Cover……………………………………………………………………………………………………… 1
Revision Sheet…………………………………………………………………………………………….2
Table of Contents…………………………………………………………………………………………3
1. Weld Map D230-06A/B……………………………………………………………………………….4
2. Weld Map D230-03…………………………………………………………………………………...6
3. Weld Map D230-04 ……………………………………………………………………………………….8
4. Weld Map D230-05 …………………………………………………………………………………………...10

3 of 11
EQUIPMENT TAG NO : D ‐ 320 ‐ 06 A/B ( LPG Tank )
PROJECT NO : 26071 WELDING AND NDE MAP SUMMARY
Material Thk  Joint  Heat 
No Joint No WPS No. NDE Method MDMT Groove / Fillet Impact Test Remarks
at Weld (mm) Category Treatment
1 E01 ‐ MH‐1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
2 E01 ‐ MH‐2 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
3 E01 ‐ N‐3 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
4 E01 ‐ N‐5 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
5 E01 ‐ P‐1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
6 E01 ‐ N‐2 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
7 E01 ‐ N‐6 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
8 E01 ‐ V‐1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
9 E01 ‐ N‐4 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
10 E01 ‐T‐1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
11 E01 ‐N ‐7 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
12 E02 ‐ N1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
W11‐SM‐552LF 
13 E02 ‐ T2 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
14 E02 ‐ L1 VT / UT ‐42.2 47 Groove + Fillet D YES YES*
15 F‐1  MT /PT ‐42.2 29 Fillet ‐ YES YES*
16 F‐4 MT /PT ‐42.2 29 Fillet ‐ YES YES*
17 F‐5 MT /PT ‐42.2 29 Fillet ‐ YES NO
18 DP ‐ 2 MT /PT ‐42.2 25 Fillet ‐ YES YES*
19 DP ‐ 5 MT /PT ‐42.2 25 Fillet ‐ YES YES*
20 BT ‐ 2 MT /PT ‐42.2 9 Fillet ‐ YES YES*
21 H ‐1 MT /PT ‐42.2 70 Fillet ‐ YES YES*
22 R ‐1 MT /PT ‐42.2 70 Fillet ‐ YES YES*
23 HD ‐1 MT /PT ‐42.2 70 Fillet ‐ YES YES*
24 SP ‐1 MT /PT ‐42.2 12 Fillet ‐ YES YES*
25 C01 RT N/A 8 Butt ‐ N/A N/A
26 C02 RT N/A 8 Butt ‐ N/A N/A
27 C03 RT N/A 8 Butt ‐ N/A N/A
28 C04 RT N/A 8 Butt ‐ N/A N/A
W88‐TM‐001 or W88‐GT‐001
29 C05 RT N/A 8 Butt ‐ N/A N/A
30 C06 RT N/A 8 Butt ‐ N/A N/A
31 C07 RT N/A 8 Butt ‐ N/A N/A
32 C08 RT N/A 8 Butt ‐ N/A N/A
33 F‐2 MT /PT N/A 29 Fillet ‐ N/A N/A
34 F‐3 MT /PT N/A 29 Fillet ‐ N/A N/A
35 F‐6 MT /PT N/A 25 Fillet ‐ N/A N/A
36 ULC‐1 MT /PT N/A 29 Fillet ‐ N/A N/A
37 DP ‐ 1 MT /PT N/A 6 Fillet ‐ N/A N/A
38 DP ‐ 3 MT /PT N/A 25 Fillet ‐ N/A N/A
39 DP ‐ 4 MT /PT N/A 25 Fillet ‐ N/A N/A
40 BT ‐ 1 W11‐GT‐001 or W11‐FC‐001 MT /PT N/A 9 Fillet ‐ N/A N/A
41 E ‐ 1 MT /PT N/A 29 Fillet ‐ N/A N/A
42 LC ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
43 PB ‐ 1 MT /PT N/A 12 Fillet N/A N/A
44 E ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
45 LC ‐ 3 MT /PT N/A 29 Fillet ‐ N/A N/A
46 LC ‐ 4 MT /PT N/A 29 Fillet ‐ N/A N/A
47 ULC‐2 MT /PT N/A 12 Fillet ‐ N/A N/A

Note : * Heat Treatment will be done at site after complete all of welding
F-6 Material Joint
WPS NO. JOINT NO.
Thickness Type
F-1~5 29t Fillet
E01~02 47t Fillet
ULC-1~2 29t Fillet
DP-2~5 25t Fillet
W11-SM-552L-F BT-1~2 9t Fillet
H-1 70t Fillet
F-2 R-1 70t Fillet
HD-1 70t Fillet
SP-1 12t Fillet
NOTE
W88-TM-001 or W88-GT-001 C01~08 8t butt
E-1~2 29t Fillet 1.UNLESS OTHERWISE , SPECIFIED WPS No. OF WELD PART
F-3
LC-2~4, 29t Fillet SHALL BE APPLIED W11-GT-001 OR W11-FC-001
W11-GT-501 or W11-FC-501
DP-1 6t Fillet 2. FCAW PROCESS IS ONLY FOR NON-PRESSURE PARTS.
PB-1 12t Fillet 3. PWHT : YES / MDMT: -42.2

DESCRIPTION WELDING PLACE

Shell to Upper Cloumn & Nozzle Shop Welding

Shell to Shell Field Welding
Upper Cloumn to Lower Cloumn Field Welding
Others Refer to latest Drawing
F-4

ULC-2

F-5

Material
Thickness
(mm)

....
....
....
.... ....
....
....
....
....
....
....
....
....
D-320-06A/06B
REV.
.... ....
WELDING MAP
.... DWG. NO.
.... 26071-V66A-D-320-06A-00002

.... DOC. NO.

26071-203-V66A-MTFR-20044
EQUIPMENT TAG NO : D ‐ 320 ‐ 03 ( Saturated C4 Tank )
WELDING AND NDE MAP SUMMARY
PROJECT NO : 26071
Material Thk  Joint  Heat 
No Joint No WPS / PQR No. NDE Method MDMT Groove / Fillet Impact Test Remarks
at Weld (mm) Category Treatment
1 E ‐ 1 MT /PT N/A 29 Fillet ‐ N/A N/A
2 LC ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
3 PB ‐ 1 MT /PT N/A 12 Fillet N/A N/A
W11‐GT‐001 or W11‐FC‐001
4 E ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
5 LC ‐ 3 MT /PT N/A 29 Fillet ‐ N/A N/A
6 LC ‐ 4 MT /PT N/A 29 Fillet ‐ N/A N/A
Note : * Heat Treatment will be done at site after complete all of welding
 Material Joint
WPS NO. JOINT NO.
Thickness Type

E-2, 17.5t Fillet

W11-GT-001 or W11-FC-001 LC-2~4 17.5t Fillet
PB-1 12t Fillet

NOTE
1.UNLESS OTHERWISE , SPECIFIED WPS No. OF WELD PART
SHALL BE APPLIED W11-GT-001 OR W11-FC-001

2. FCAW PROCESS IS ONLY FOR NON-PRESSURE PARTS.

3. PWHT : NO / MDMT: -5

DESCRIPTION WELDING PLACE

Lower Cloumn Shop Welding

D-320-03
REV.

WELDING MAP
DWG. NO.
26071-V66A-D-320-03-00006

DOC. NO.
26071-203-V66A-MTFR-20044
EQUIPMENT TAG NO : D ‐ 320 ‐ 03 ( Saturated C4 Tank )
WELDING AND NDE MAP SUMMARY
PROJECT NO : 26071
Material Thk  Joint  Heat 
No Joint No WPS / PQR No. NDE Method MDMT Groove / Fillet Impact Test Remarks
at Weld (mm) Category Treatment
1 E ‐ 1 MT /PT N/A 29 Fillet ‐ N/A N/A
2 LC ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
3 PB ‐ 1 MT /PT N/A 12 Fillet N/A N/A
W11‐GT‐001 or W11‐FC‐001
4 E ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
5 LC ‐ 3 MT /PT N/A 29 Fillet ‐ N/A N/A
6 LC ‐ 4 MT /PT N/A 29 Fillet ‐ N/A N/A
Note : * Heat Treatment will be done at site after complete all of welding
 Material Joint
WPS NO. JOINT NO.
Thickness Type

E-2, 17t Fillet

W11-GT-501 or W11-FC-501 LC-2~4 17t Fillet
PB-1 12t Fillet

NOTE
1.UNLESS OTHERWISE , SPECIFIED WPS No. OF WELD PART
SHALL BE APPLIED W11-GT-001 OR W11-FC-001

2. FCAW PROCESS IS ONLY FOR NON-PRESSURE PARTS.

3. PWHT : YES / MDMT: -4.2

DESCRIPTION WELDING PLACE

Lower Cloumn Shop Welding

D-320-04
REV.

WELDING MAP
DWG. NO.
26071-V66A-D-320-04-00006

DOC. NO.
26071-203-V66A-MTFR-20044
EQUIPMENT TAG NO : D ‐ 320 ‐ 05 A/B/C/D ( Propylene Tank )
WELDING AND NDE MAP SUMMARY
PROJECT NO : 26071
Material Thk  Groove /  Joint 
No Joint No WPS / PQR No. NDE Method MDMT Impact Test Heat Treatment Remarks
at Weld (mm) Fillet Category
1 E ‐ 1 MT /PT N/A 29 Fillet ‐ N/A N/A
2 LC ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
3 PB ‐ 1 MT /PT N/A 12 Fillet N/A N/A
W11‐GT‐001 or W11‐FC‐001
4 E ‐ 2 MT /PT N/A 29 Fillet ‐ N/A N/A
5 LC ‐ 3 MT /PT N/A 29 Fillet ‐ N/A N/A
6 LC ‐ 4 MT /PT N/A 29 Fillet ‐ N/A N/A
Note : * Heat Treatment will be done at site after complete all of welding
 Material Joint
WPS NO. JOINT NO.
Thickness Type

E-2, 17.5t Fillet

W11-GT-501 or W11-FC-501 LC-2~4 17.5t Fillet
PB-1 12t Fillet

NOTE
1.UNLESS OTHERWISE , SPECIFIED WPS No. OF WELD PART
SHALL BE APPLIED W11-GT-001 OR W11-FC-001

2. FCAW PROCESS IS ONLY FOR NON-PRESSURE PARTS.

3. PWHT : YES / MDMT: -47.5

DESCRIPTION WELDING PLACE

Lower Cloumn Shop Welding

D-320-05A/05B/05C/05D
REV.

WELDING MAP
DWG. NO.
26071-V66A-D-320-05A-00002

DOC. NO.
26071-203-V66A-MTFR-20044