Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 1 of 12

Product Code/Name LZYB-B3-ZA01 Type of Anti-Riot Road Blocker

Inspected Units Beijing ZhuoAoShiPeng Technology Co., Ltd.

Entrustment Unit Beijing ZhuoAoShiPeng Technology Co., Ltd.

Inspected Units Address Room A2006, No.4, Fufeng Road, Fengtai District, Beijing, China
Contact
Information Zip Code 100070 Phone Number 18001332737

Samples No. GJJ（Sample）No. 1700425

Sampling
Sampling Date 2017.9.1 Factory warehouse
Locations

Sampling Basic Two road blocker samples

10 Sample Qty.
Number and one material sample

Sample
Production Date 201708 2017.11.2
Received Date

Test Standard China Anti-Riot Lifting Barrier Industry Standard（GA/T 1343-2016）

Judgment Basis China Anti-Riot Lifting Barrier Industry Standard（GA/T 1343-2016）

Inspection Date 2017.11.2 - 2018.1.9

The sample inspection of LZYB-B3-ZA01 type of anti-riot road blocker, offered by Beijing
ZhuoAoShiPeng Technology Co., Ltd., the test results of all items in accordance with China
Anti-Riot Lifting Barrier Industry Standard（GA/T 1343-2016）, meet B3 blocking ability level.
Test
Conclusion

Date: 2018.1.9

Editor: Review: Approval:

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 2 of 12

Test Site & Main Equipment for Test

Beijing Shenhuada Traffic Engineering Testing Co., Ltd.

Test Site
/

General standard measuring tool

HRT5020F Walk-in type temperature and humidity heat test chamber

ESD-30A Electrostatic discharge tester

MI2094 Comprehensive safety tester

Main Equipment
YWX/Q-016 Salt spray test chamber
for Test

NX5 Conducted immunity tester

HS-10W Electronic stopwatch

PCM-2731 Vehicle Handling Stability Test System

KCCF-4011 Vehicle tilting test bench

The sample is a hydraulically-driven, riot-prevention, automatic road blocker,

consisting of barrier blocking part, a power (hydraulic) system, and a control
system.

The width of barrier blocking part is 3000mm. the maximum rise height is 650mm.
Top steel plate thickness is 25mm.

The power (hydraulic) system is additionally equipped with a low-temperature

Sample Overview
self-heating device, which can be automatically activated to the power (hydraulic)
system when the outside temperature is lower than 10°C.

Sample numbering method: No. 1-2, road blocker, No. 4, salt spray test sample.
 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 3 of 12

Test Items & Test Results

Sample Judgem
No. Test Items Technical (standard) Requirements Test Results
No. ent

Anti-riot lifting barrier are generally

composed of barrier main structure, a
power system, and a control system; the
surface of the barrier shall be with no
General
rust and mechanical damage; the
1 Requirements 1 Meet the requirement P
fastening parts shall be solid, reliable,
Test
and free from loosening, and the lifting
shall be flexible; the main structure of
the barricade shall be in conformity
Design drawings requirements

Barriers should have a fixed, clear and

permanent sign on the prominent
position of the main body. The sign
should include the following:
Sign
2 a) the name of the manufacturer; 1 Meet the requirement P
Inspection
b) product name and code;
c) the nature of the power supply;
d) implementation of standard number;
e) Production period (year month)

The height of the barrier blocking part

Blocking
should be greater than or equal to
Height and The height of the barrier blocking part
3 600mm; the distance between the 1 P
Spacing after raised is 650mm
blocking body should be less than or
Check
equal to 800mm

Security barrier blocking part should be

capable of lifting, no jamming, reliable
Lift
in place; rising speed is 150mm/s or Barrier blocking part rising speed:
4 Performance 1 P
more; with no power supply, should be 167mm/s, with manual lifting function
Test
provided with power or with manual
lifting function

Barrier blocking part should have

Warning Sign Reflective tape on barricade
5 obvious warning signs and have night 1 P
Inspection blocking part meets requirements
warning function

P：Passed F：Failed N/A：Not applicable A：Allow

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 4 of 12

Test Items & Test Results

Samp Judge
No. Test Items Technical (standard) Requirements Test Results
le No. ment
Test Energy Vehicle Impact Speed Energy (kJ)
The medium truck was weighted
Code Weight(kg) (km/h)
to 6891 kg and impact the road
Impact A 6800 80 1679 blocker at a speed of 64.7 km/h.
Energy
B 6800 65 1108 After test, the vehicle lost its

C 2300 100 887 ability to continue driving. The

vehicle major debris distance
D 1500 100 579
was: 15.5 m. The barrier remains
E 1500 65 245
blocked and works normally,
Remarks: The impact test allowable deviation is shown in Table A.2 meeting B3 requirements. The
Major Debris Distance Code Distance(m) technical parameters of the test
Major vehicle are shown in the
1 <1
Debris following table.
6 2 1. 01~7 2-3 P
Distance
Blocking 3 7，01~30 Axles number 2

Performa Major Debris Distance Code Total vehicle weight 6891kg

Test Energy
nce Test Vehicle weight 4252kg
Code 1 2 3
Front wheel distance 1750mm

A A1 A2 A3 Wheel radius 428mm

Blocking B B1 B2 B3 Wheelbase 4130mm
Ability C C1 C2 C3 Total length of vehicle 7330mm

D D1 D2 D3 Total vehicle width 2150mm

E E1 E2 E3 Impact angle 90.1°

After test, the vehicle loses its ability of driving, and the
Impact speed 64.7km /h
barrier should be able to remain blocked situation.
The insulation resistance between the power plug and
the exposed metal parts of the enclosure shall be not
less than 5MΩ after the relative humidity heat of 91%
Insulation to 95%, the temperature of 40°C, and 48 hours, and the
Resistance basic insulation device is not Less than 2MΩ, class III Meet the requirement
Test equipment is not less than 1MΩ. For equipment with an

Control operating voltage exceeding 500V, the resistance of the

System above insulation resistance shall be multiplied by a

7 1 P
Safety factor equal to the operating voltage divided by 500V.

Test Leakage The leakage current during the operation of Class I and
Current Class II equipment shall comply with the requirements in 0.22mA
Test Table 2 of GB16796-2009. Class Ⅲ no need do this test.

Insulation Between the power plug and the exposed metal parts of
Withstan enclosure, it shall withstand the insulation test of 45Hz
Meet the requirement
d Voltage ~65Hz AC voltage specified in Table 1 of GB16796-2009, and
Test there shall be no breakdown and arcing in 1min.
 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 5 of 12

Test Items & Test Results

Samp Judge
No. Test Items Technical (standard) Requirements Test Results
le No. ment

The control system's electrostatic discharge

Electromagneti immunity, electrical fast transient burst immunity,
8 c Compatibility surge (impact) immunity shall be in accordance with 1 Meet the requirement P
Test the provisions of 9,3.4, 12.3.4, and 13.3.4 of GB/T
30148-2013.

Soaking Barrier blocking main structure should be no leakage Barrier blocking structure is placed in
9 Performance phenomenon in the flooding state, and can lift 1 the pool to soak 48h no leakage P
Test normally phenomenon, and can normally lift

Barrier blocking main structure should be rust-proof,

corrosion resistance grade should be ≥ 7

Defect Area (A) Grade（Rρ or RA）

10
No Defect

0 < A ≤ 0.1％ 9

0.1％< A ≤ 0.2 5％ 8

0.25％< A ≤ 0.5％ 7

10 Anti-Corrosio 3 Corrosion resistance grade：8 P

0.5％< A ≤ 1.0％ 6
n Performance
1.0％< A ≤ 2.5％ 5

2.5％< A ≤ 5％ 4

5％< A ≤ 10％ 3

10％< A ≤ 25％ 2

25％< A ≤ 50％ 1

A > 5 0％ 0

The security barrier is continuously

raised and lowered 5000 times
At room temperature, the security barrier shall be
11 Operation according to the lifting frequency of
continuously lifted 5000 times with no downtime 1 P
Stability Test 2 times/min, no stoppage and failure
and failure, and the lifting is flexible and accurate.
occurs, and the lifting is flexible and
accurate.

P：Passed F：Failed N/A：Not applicable A：Allow

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 6 of 12

Test Items & Test Results

Sampl Judge
No. Test Items Technical (standard) Requirements Test Results
e No. ment

Put the blocking main structure and

power (hydraulic) system of barrier into
the thermostatic chamber with
temperature -30 °C ± 2 °C, keep it for
24h, and then take the electricity test
after taking it out. The barrier's blocking
part can normally move up and down,
Barrier blocking part and power system should there is no jamming, and the position is
be capable of normal work under ambient reliable; Starting speed: 161mm/s.
Environmental
12 temperature -30 °C ± 2 °C ~ 55 °C ± 2 °C. 1 P
Suitability Test
No jamming, reliable positioning, barrier Put the blocking main structure and
rising speed greater than or equal to 150mm/s power (hydraulic) system of barrier into a
thermostatic chamber with temperature
of 55 °C ± 2 °C, keep it for 24 hours,
and then take the electricity test after
taking it out. The blocking part of the
security barrier can normally rise and fall
without any stagnation and reliable
place; Speed: 168mm/s

P：Passed F：Failed N/A：Not applicable A：Allow

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 7 of 12

Status of LZYB-B3-ZA01 type of road blocker before crash test

LZYB-B3-ZA01 type of road blocker control system and power (hydraulic) system
 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 8 of 12

Before the test, the appearance of the vehicle

Before test, vehicles and security barrier

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 9 of 12

After test, vehicle status

After test, vehicle status

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 10 of 12

Security barrier appearance after test

 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report
GJJ No.1731630 Page 11 of 12

Electrostatic discharge immunity test layout

Electrostatic discharge immunity test connection diagram of the device under test
 Ministry of Public Security Security and Police Electronic Product Quality Testing Center

Test Report

GJJ No.1731630 Page 12 of 12

Electrical fast transient burst immunity test layout

Electrical fast transient burst immunity test connection diagram