M1659200A.

1
ITEM NUMBER: 1659200, 1659201,1659202
® SERIAL NUMBER: ___________________

Owner’s Manual
Instructions for Installation/Set-up, Operation, Servicing, & Storage
Portable Outdoor Use-Only, Direct-Driven Replacement Generator
1659200 - 3,000 Watt Continuous (3,500 Watt Surge) Capacity
1659201 - 4,000 Watt Continuous (4,500 Watt Surge) Capacity
1659202 - 6,000 Watt Continuous (6,500 Watt Surge) Capacity
WARNING
READ and UNDERSTAND this manual completely before using the generator! Failure to properly set up, operate, and maintain this
generator could result in serious injury or death from carbon monoxide poisoning, electric shock, entanglement, fire, or burns. In
addition, an improperly secured generator can lift or flip and cause severe injury. In particular, be aware of the following hazards:

CO Poisoning
The running engine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it.
• ONLY run generator-engine assembly OUTDOORS and AWAY from building air intakes. NEVER run inside any enclosed or semi-
enclosed spaces, including homes, basements, garages, sheds, and boxes. These spaces can trap poisonous gases, EVEN if you run a fan or
open windows.
• Install carbon monoxide alarms inside nearby structures/buildings (battery-operated, or plug-in with battery backup).
Electric shock / Electrocution
• High voltage electricity from generator can kill. DO NOT operate in wet locations. Be sure generator is properly grounded. Use only UL-
listed, outdoor-rated grounded GFCI-equipped extension cords of proper size.
• NEVER plug the generator directly into a wall outlet. ANY connection to a building’s electrical system MUST ISOLATE THE
GENERATOR FROM UTILITY POWER via a UL-approved transfer switch installed by a licensed electrician. Otherwise, back feed from
the generator into the power grid could kill utility workers.
Fire
• DO NOT overload generator (per rated capacity), and OPERATE ONLY in an area with adequate cooling ventilation so generator does not
overheat and possibly cause fire. Keep all objects at least 7’ from generator vent openings. Refer to engine owner’s manual for minimum
safe clearance distance between hot engine exhaust and nearby combustible materials/structures.
• ALWAYS keep a fire extinguisher rated “ABC” nearby.
Entanglement / Moving Object Impact
• Never operate the generator without proper guarding of the power transmission assembly, including all rotating shafts, pulleys, belts, and
couplings. Clothing or hair can become rapidly entangled in unguarded rotating parts, resulting in serious injury or death.
• Failure to properly mount and secure the generator may cause the unit to lift or flip during use, which could result in severe injury to the
operator or bystanders, or cause damage to surrounding objects.
Also see “Summary of Important Safety Information” in this manual.

STOP!
CHOOSE THE RIGHT GENERATOR FOR YOUR NEEDS. See the “Power load Planning & Management” section of this manual to
determine your power load requirements and then compare to the generator’s rated capacity.
INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged. See the “Unpacking & Delivery
Inspection” section for instructions on whom to contact to report missing or damaged parts.
ENGINE and MOUNTING REQUIRED. You will need to supply an engine to power this generator. The generator and engine must be
mounted to each other. See the “Specifications”, “About Your Generator”, and “Installation/Initial Set-Up” sections of this manual for more
information on these requirements.
ARRANGE FOR PROFESSIONAL INSTALLATION of a transfer switch if you will be connecting the generator to your building’s
electrical system. See the “Installation/Initial Set-Up” section for more information about this requirement.

Any Questions, Comments, Problems, or Parts Orders

Call NorthStar Product Support 1-800-270-0810
1
Hazard Signal Word Definitions

2
 Table of Contents

Hazard Signal Word Definitions .................................................................................................2

About Your Generator .................................................................................................................4

Specifications .................................................................................................................................6

Safety Label Locations..................................................................................................................7

Machine Component Identification.............................................................................................8

Power Load Planning & Management ........................................................................................10

Installation / Initial Set-Up:

1. Unpacking & Delivery Inspection..........................................................................................12
2. Planning the Power Load........................................................................................................12
3. Set-up as a PORTABLE or BUILDING BACK-UP Power Source ......................................13
4. Selecting a Suitable Site .........................................................................................................15
5. Mounting & Connecting Generator and Engine.....................................................................17
6. Connecting Generator Wire Harness to Existing Wiring .......................................................21
7. Grounding the Generator........................................................................................................22

Operation:
1. General Safety Rules for Operation .......................................................................................23
2. Preparing for Operation (Pre-start checklist) .........................................................................25
3. Starting the Generator.............................................................................................................27
4. Connecting Loads...................................................................................................................28
5. Stopping..................................................................................................................................29
6. Storage & Exercise .................................................................................................................30

Maintenance & Repair..................................................................................................................32

Troubleshooting.............................................................................................................................34

Summary of Important Safety Information ...............................................................................35

Fastener Identification..................................................................................................................39

Generator Exploded View and Component Lists.......................................................................41

Warranty........................................................................................................................................44

3
 About Your Generator
Thank you for purchasing your NorthStar direct-driven generator!
About Your Generator
This direct-driven, portable generator is designed to provide up to:
Required Engine
Continuous Watts Surge Watts
Horsepower
1659200 3000 3500 6 hp
1659201 4000 4500 9 hp
1659202 6000 6500 13 hp
Powered by an external engine, this generator can supply power:
1. As a portable power source. You can plug appliances directly into the generator’s
electrical outlets.
2. As a back up, standby power source for a building. A licensed electrician can connect
the generator to your building’s electrical system via the installation of an UL-approved
transfer switch. (See the “Installation & Initial Set-up” section of this manual to learn
more about specific requirements and precautions relating to wiring the generator to your
building’s electrical system.)
You must select a generator adequately sized for your power needs. You need to
determine the power needs of all the appliances/tools you wish to power at the same time and
choose a generator rated to provide at least that power level. See the “Power Load Planning &
Management” section of this manual to determine your specific power load requirements and
then compare them to this generator’s rated capacity. You must not overload the generator.
Overloading will cause damage to the generator and attached electrical devices, and may also
result in fire.
This generator and the engine must be mounted together. More detailed information about
mounting can be found in the “Installation / Initial Set-Up” section of this manual.
Be sure to read about site selection and grounding requirements for running this
generator. More detailed information can be found in the “Installation & Initial Set-up, Steps
5 & 6” of this manual.
CAUTION: This generator is too heavy for one person to lift without assistance.
Optional accessories available from NorthStar include UL-approved transfer switches and
extension cords. Contact NorthStar Product Support at 1-800-270-0810 with questions
about optional accessories or to order.
Read this Manual
WARNING
Improper use or maintenance of the generator can result in serious injury or death from
carbon monoxide poisoning, electric shock, entanglement, fire, or burns. In addition,
an improperly secured generator can lift or flip and cause severe injury.
Read this manual completely before using the generator and follow all instructions and
safety rules.

4
 About Your Generator (cont’d)
You must follow all instructions and safety precautions presented throughout this manual. A
summary of important safety information can be found at the end of the manual. Keep this
manual for reference and review.
Proper preparation, operation, and maintenance will result in operator safety as well as best
performance and long life of the generator. Failure to follow the instructions in this manual
for proper mounting, set-up, operation, and maintenance of the generator will void the
manufacturer’s warranty.
Before using, the user shall determine the suitability of this product for its intended use and
assumes liability therein. The purchaser and/or user shall assume liability for any modification
and/or alterations of this equipment from original design and manufacture, or for any non-
standard application, or for use as a subcomponent in another piece of equipment.
NorthStar is constantly improving its products. The specifications outlined herein are subject
to change without prior notice or obligation.
Contact NorthStar Product Support at 1-800-270-0810 for any questions about the
appropriate use of this generator.

Warranty Registration
Please fill out and submit the warranty registration section at the end of this manual so that you
have information for future product literature or replacement parts you may need.

ATTENTION:
All Rental Companies and Private Owners who loan this
equipment to others!
All persons to whom you rent/loan this generator must have access to and read this manual. Keep this
owner’s manual with the generator at all times and advise all persons who will operate the machine to
read it. You must also provide personal instruction on how to safely operate the generator and remain
available to answer any questions a renter/borrower might have.

5
 Specifications

SPECIFICATIONS
Item Number 1659200 1659201 1659202
Maximum
3500 Watts (W) 4500 Watts (W) 6500 Watts (W)
Output
Continuous
3000 Watts (W) 4000 Watts (W) 6000 Watts (W)
Output
Voltage 120 / 240 Volt (V) 120 / 240 Volt (V) 120 / 240 Volt (V)
Single phase Single phase Single phase
Phase
(4-wire) (4-wire) (4-wire)
58.0 – 63.0 Hertz 58.0 – 63.0 Hertz
Frequency 58.0 – 63.0 Hertz (Hz)
(Hz) (Hz)
Power Factor 1.0 p.f. 1.0 p.f. 1.0 p.f.
Engine HP
6 hp 9 hp 13 hp
(minimum)
Engine Speed 3540-3720 RPM 3540-3720 RPM 3540-3720 RPM
Torque 9 ft-lbs 14 ft-lbs 19 ft-lbs
Engine Drive 2¼” taper per foot 2 ¼” taper per foot 2 ¼” taper per foot
Shaft length of engine shaft length of engine shaft length of engine shaft
Dimensions
Length 11” 12.5” 12.75”
Width 7.125” 7.5” 9.4”
Height 7” 7.2” 9.75”
Gross
29.5 lb. (13.4 kg) 39 lb. (17.7 kg) 60.4 lb. (27.4 kg)
Weight

6
 Safety Label Locations

DANGER
Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide. This is
a poison you cannot see or smell.

NEVER use inside a home Only use OUTSIDE and

or garage. EVEN IF doors far away from windows,
and windows are open. doors, and vents.

WARNING
HIGH VOLTAGE from generator
can shock or kill.
NEVER connect generator directly into a wall outlet.
ANY connection to a building’s electrical system
MUST ISOLATE GENERATOR FROM UTILITY
POWER via a transfer switch.
Be sure generator is properly grounded.
Use only outdoor−rated grounded GFCI
extension cords of proper size.
DO NOT operate in wet locations.

Clothing or hair can become rapidly

ENTANGLED in unguarded rotating
parts, resulting in serious
injury or death.
ONLY operate with proper guarding of power
transmission system, including all rotating shafts, Always make sure safety labels are in place and
pulleys, belts and couplings. in good condition. If a safety label is missing or
FIRE can result from: not legible, order new labels or unsafe operation
Overloading the generator could result.
Lack of cooling ventilation
Contact with hot engine exhaust
DO NOT overload generator
To order replacement safety labels, call NorthStar
OPERATE ONLY with adequate cooling ventilation. Product Support at 1-800-270-0810.
Keep all objects at least 7 feet from generator vent
openings.
Keep engine exhaust a safe distance away from all
combustible objects.
ALWAYS keep a fire extinguisher nearby.

Generator may LIFT or FLIP during On-Product Warning Labels

use if improperly mounted.
Part numbers Description
Generator and engine must be properly mounted
to a common base. 779407 CPSC Warning
©
Read Owner’s Manual completely before using. NTE 780342 General Warning

7
 Machine Component Identification

Ref Description Ref Description

1 Drive End Bracket 5 Fan Vents
2 Non-Drive End Bracket 6 Fan
3 End Cover 7 Input Shaft
4 Grounding screw slot 8 Engine Adapter Plate

8
 Machine Component Identification (cont’d)

REFERENCE GUIDE
Reference 1 – Drive End Bracket Connects to the Engine Adapter Plate
Reference 2 – Non-Drive End Bracket Bracket requires support underneath to keep engine and generator
level
Reference 3 – End Cover Protective end cover shields operator from moving parts
Reference 4 – Grounding Screw Ground the generator via the ground screw, to a copper pipe or
rod that is driven into moist soil.

Reference 5 – Fan Vents Never block the vent slots or insert objects through the slots
(vents allow for cooling air to pass through generator)
Reference 6 – Fan Fan pulls air through the generator
Reference 7 – Input Shaft Engine input shaft must fit snuggly into tapered hole
Reference 8 –Engine Adapter Plate Connect plate to the engine and drive end bracket
Engine adapter plate must be installed flush with engine or
damage will occur to both engine and generator.

9
 Power Load Planning & Management
WARNING
NEVER exceed the rated wattage capacity of your generator.

OVERLOADING may cause SERIOUS DAMAGE to the generator and attached

electrical devices, and may result in fire.

Your generator MUST BE SIZED PROPERLY to provide both the running and starting (surge) wattage of
the devices you will be powering. Before using your generator, determine the running and starting wattage
requirements of all the electrical devices you will be powering simultaneously. The sum of the running and
starting wattages of the devices being powered must not exceed the continuous output rating of your
generator. (The continuous output rating of your generator is listed in the “Specifications” section of this
manual.) Note that:

• Devices without electric motors such as light bulbs, radios, and televisions have the same running
and starting wattage.
• Devices with electric motors such as refrigerators, compressors, and hand tools typically require a
starting wattage that is 3 to 5 times greater than the running wattage.

The running and starting wattage requirements are often listed on a device’s nameplate. If wattage is not
given on the device’s nameplate, the wattage may be calculated by multiplying the nameplate voltage by
nameplate amperage, Watts = Volts X Amps.

Example conversion to watts:

120 Volts X 5 Amps = 600 Watts

If only the running voltage is given on the nameplate for a device with an electric motor, the starting wattage
can be approximated to be three to five times the running wattage.

Estimates for the running wattage requirements for common devices are listed in Table 4 below. Guidance
for starting wattages is provided in the table’s footnotes.
Table 4
Running Running
Device Watts Device Watts
Air conditioner (12.000 BTU) 1700 (a,b) Jet pump 800 (a)
Battery charger (20 Amp) 500 Lawn mower 1200
Belt sander (3”) 1000 Light bulb (100 Watt) 100
Chain saw 1200 Microwave oven 700
Circular saw (6½”) 2000 (a,b) Milk cooler 1100 (a)
Coffee maker 1800 (a,b) Oil burner on furnace 300
Compressor (1 HP) 1400 (a,b) Oil-fired space heater (140,000 Btu) 400
Compressor (3/4 HP) 1800 (a) Oil-fired space heater (85,000 Btu) 225
Compressor (1/2 HP) 1400 (a) Oil-fired space heater (30,000 Btu) 150
Curling iron 700 Oven 4500
Dishwasher 1200 Paint sprayer, Airless (1/3 HP) 600 (a)
Edge trimmer 500 Paint sprayer, Airless (handheld) 150
Electric nail gun 1200 Radio 200
Electric range (1 element) 1500 Refrigerator 600 (b)
Electric skillet 1250 Slow cooker 200

10
 Power Load Planning & Management (cont’d)
Running Running
Device Watts Device Watts
Furnace fan (1/3 HP) 1200 (a) Submersible pump (1-1/2 HP) 2800 (a)
Freezer 800 (b) Submersible pump (1 HP) 2000 (a)
Hair dryer 1200 Submersible pump (1/2 HP) 1500 (a)
Hand drill (1”) 1100 Sump pump 600 (a)
Hand drill (1/2”) 875 Table saw 2000 (a)
Hand drill (3/8”) 500 Television 500
Hand drill (1/4”) 250 Toaster 1000
Hedge trimmer 450 Vacuum cleaner 250
Home computer 150 VCR 70
Impact wrench 500 Water Heater 3000
Weed trimmer 500
(a) Hard-starting motors require 3-5 times the rated running watts
(b) For extremely hard to start loads such as air conditioners and air compressors, consult the equipment
dealer to determine maximum wattage

To calculate the running and starting wattage requirements for the devices you will be powering,
follow these steps:

1. Make a list of all electrical devices you will be powering at the same time with the generator.

2. List the greater of the running or starting wattage next to each device as obtained from the devices’
nameplate or Table 4. If only the running wattage for a device with an electric motor is known, the
starting wattage can be estimated to be at least 3 times the running wattage.

3. Add the wattages for all devices on your list. This total must be lower than the continuous output
rating of your generator.
Example:
Greater of Starting/Running
Device to be Powered Wattage
Light Bulb 75 W
Refrigerator – 18 Cu. Ft. 1600 W
Microwave 700 W
Window AC 1800 W
Sump pump (1/3 hp) 2100 W
Total 6275W

In this example, the generator must have a continuous output of at least 6275 W in order to power all
of the devices simultaneously.

STAGGERING LOADS
You can increase the number of devices your generator can power by staggering the load on the generator.
For example, you could alternately power your refrigerator and air conditioner for limited periods of time --
powering only one of the devices at a time and never powering both at the same time.

11
 Installation / Initial Set-Up
There are a number of important steps required to set up your generator for initial use. These steps are:

Steps for Installation / Initial Set-Up

1. Unpacking & delivery inspection.
2. Planning the power load to stay within the generator’s rated capacity.
3. Setting up for the type of power generation you need:
a. portable power source, or
b. connected to a building as a back-up power source.
4. Selecting a site for using the generator.
5. Mounting & connecting generator to engine.
6. Connecting Generator Wire Harness to Existing Wiring
7. Grounding.

Each of these steps is discussed in detail below:

1. Unpacking & Delivery Inspection

1. You should inspect the generator immediately after you receive delivery.
See the “Machine Component Identification” section of this manual for a
diagram of the generator and its components.
• If you have missing components, contact Product Support at 1-800-270-0810.
• If you have damaged components, contact the freight company that delivered the unit and file a claim.

2. Planning the Power Load

Plan your power load so that you do not exceed the generator’s rated capacity.

See the “Power Load Planning & Management” section of this manual to review how to plan and
manage power loads for the generator.

12
 Installation / Initial Set-Up
3. Set-up either as a BUILDING BACK-UP or PORTABLE Power Source
Each model generator is designed to provide a particular amount of continuous electrical power
1659200 - 3000Watts 1659201 - 4000Watts 1659202 - 6000Watts
It can supply electricity in two ways:
1. As a back up, standby power source for a building. For this application, you must arrange
for a licensed electrician to connect the generator to your building’s electrical system via the
installation of an UL-approved transfer switch. The transfer switch must be installed in
accordance with building electrical code and guidelines supplied by your power company.
2. As a portable power source. You can plug appliances or tools directly into the generator’s
electrical outlets.
Specific requirements for each are given below.
Note: Regardless of whether you use your generator as a back-up power source connected to a building or as a
portable power source, you must not overload the generator. Overloading may cause serious damage to the
generator and attached electrical devices.

Using as a Contact a licensed electrician to install an UL-approved transfer switch if you

Back-up Power want to use your generator as a back-up power source for a building.
Source for a Building
What does a transfer switch do? It:

a) Safely connects the generator to your building’s electrical system by isolating

your generator from your utility company’s power lines, AND
b) Connects your generator to a critical subset of your building’s circuits that are
needed for emergency power needs.

If your generator will be connected to your building’s electrical system, it MUST

ALWAYS be isolated from the utility power grid with a UL-approved transfer
switch installed by a licensed electrician in compliance with all applicable building
and electrical codes, and in accordance with guidelines supplied by your power
company.

DANGER:
A transfer switch must be installed in order to isolate your
generator from the utility power grid. If your generator is NOT
properly isolated from the utility system, serious hazards will arise:
♦ When your generator is running, it’s output will back feed into
the utility power line and transformer that are normally used to
provide you with power. The transformer will step up the
current to the normal line voltage. An unsuspecting utility line
worker working on what he thinks is a deactivated line could be
electrocuted.
♦ If your generator is connected (running or not) when utility
power is restored, your generator will be destroyed. It could
also explode or cause fire.

I dditi t i l ti t f th tilit t th t f it h

13
 Installation / Initial Set-Up
connects your generator to a limited set of circuits in your building that have been
chosen as critical to operate during a power outage.
Make sure to verify if this generator can power your loads, it may not power your
entire home or farm outbuilding -- you must work with the installing electrician to
determine which devices/appliances you wish to power during an outage. The
electrician can help you determine which circuits and devices can be powered
simultaneously without overloading the generator.
(See the previous section of this manual entitled “Power Load Planning &
Management” for more information on load application and selection.)

Using as a When using the generator as a portable power source, you can plug electric
Portable Power devices and appliances directly into the outlets on your generator’s panel.
Source ♦ Make sure you plug each electrical device/appliance into the correct generator
outlet based on the device’s plug configuration and voltage/amperage rating.
Never exceed the amperage rating of an outlet.
♦ Extension cords may be used to power devices that are located at a distance from
the generator. However, use only UL-listed, outdoor-rated, grounded extension
cords of the proper size. Additionally, if using the generator in damp or highly
electrical conductive areas or on construction jobsites, always use ground fault
circuit interrupter (GFCI)-equipped extension cords to prevent electrical shock.
Use Table 5 below to choose an adequately sized extension cord according to the
amperage of the device being used and the length of the cord.
Table 5
Current/Power Maximum Extension Cord Length
Amps at Load #10 Ga. #12 Ga. #14 Ga. #16 Ga.
240V (watts) Cord Cord Cord Cord
10 2400 250’ 150’ 100’ 75’
20 4800 125’ 75’ 50’ 25’
30 7200 60’ 35’ 25’ 10’
40 9600 30’ 15’ 10’ *
50 12000 15’ * * *

WARNING:
Use of under sized extension cords can cause electric shock, fire, or
damage to connected devices. Failure to use GFCI extension cords in
damp or wet conditions can result in severe electric shock or
electrocution.
♦ All extension and appliance cords must be in good condition and not worn, bare, frayed,
or otherwise damaged.
WARNING:
Use of damaged electric cords can cause electric shock or fire.
Note: If an extension cord becomes hot to the touch, it is overloaded or damaged and
must be replaced.
Northern Tool is NOT responsible for damage or injury resulting from customer use of
inadequate extension cords.

14
 Installation / Initial Set-Up
4. Select a Suitable Site
Before using the generator, you must select a suitable OUTDOOR location for installation and operation of your
generator. The location should meet all the criteria listed below.
WARNING:
You must choose a suitable site for operating your generator to avoid equipment damage
and/or injury and possible death from carbon monoxide poisoning, electric shock, or fire.
Choose a site that meets all of the criteria specified below.

Site/Location Criteria:

Dry, level surface The generator should be positioned on a dry, firm, level surface.
Ensure that the generator sits level and will not slide or shift during operation.

Outdoors only – DANGER: Carbon monoxide poisoning hazard

dangerous carbon The exhaust from the engine contains carbon monoxide (CO), a
monoxide exhaust poisonous gas that can kill. You cannot smell it, see it, or taste it.
Follow the directions below for choosing a location to operate your
generator in order to avoid carbon monoxide poisoning.
The location you choose to operate the generator must be OUTDOORS and away from
all air intakes:
• Never run the generator/engine assembly inside any closed or semi-enclosed spaces
(even if outdoors), including homes, garages, basements, barns, sheds, or boxes. These
spaces can trap poisonous gases, even if you run a fan or open windows.
• Place the generator so that the exhaust fumes from the engine will not be directed
towards people or building air intakes.
• Ensure that working, battery-operated or battery back-up carbon monoxide alarms are
used in any dwelling/structure that is in close proximity to the running generator.
• Note that this generator is NOT designed or approved for use in vehicles or marine
applications. Never run the generator inside RVs or other vehicles, on boats, or on
pick-up truck beds.
WARNING:
Never attempt to attach ductwork to the engine exhaust to allow for
installation inside an enclosure. This could cause hot air deflection,
heat build-up, and increased exhaust back-pressure, resulting in
possible exhaust leakage or damage to the generator or engine.

Adequate cooling The generator needs adequate, unobstructed flow of air to allow for proper cooling of
ventilation generator head.
• Situate so there is adequate clearance around generator to allow for cooling airflow so
that heat does not build up. Never block vent slots. The closest object should be at 7
feet away from vents.
• Do not run the generator in close proximity to other heat-generating equipment, such
as another generator. The combined heat that is generated may raise air temperature
in the immediate area and there will not be adequate cooling ventilation.
• Do not allow debris to accumulate and block airflow.
• Do not operate with a tarp, blanket, or cover surrounding the generator.

15
 Installation / Initial Set-Up

Hot engine The exhaust gas from your engine is extremely hot and can cause
exhaust clearance combustible materials to catch on fire.
• Position engine exhaust at a safe distance from all nearby combustible
materials and buildings/structures. Refer to your engine manual to determine
the safe clearance distance required.
• Equip the engine with a spark arrestor if the generator will be used near any
ignitable forest, brush, or grassy land. Make sure you comply with applicable
local, state, and federal codes.
• Keep a fire extinguisher rated “ABC” nearby. Keep it properly charged and be
familiar with its use.

No wet conditions Choose a location where the generator will NOT be exposed to rain,
snow, or direct sunlight. Exposure to water can cause electric shock.
You may operate the generator under an outdoor, canopy-like structure of heat-
resistant material that is open on all sides. Make sure that all parts of canopy are:
• at least 7’ from generator
• at an adequate safe clearance from hot engine exhaust.
Allow for adequate clearance above generator so that heat from generator does not
build up.

Away from Do not use the generator in extremely dusty or dirty conditions.
dust/dirt Excessive dust and dirt can cause premature failure of the machine.

Hearing Generators can produce noise levels of up to 95 dB in close proximity,

protection which can be dangerous to human hearing with prolonged exposure.
(This is in addition to the noise produced by the engine.)
Hearing protection may be required for persons working within 15-20 feet of the
running generator for an extended period of time.
WARNING:
Never attempt to attach ductwork to the engine exhaust to lower noise
levels. This could cause hot air deflection, heat build-up, and
increased exhaust backpressure, resulting in possible exhaust leakage
or damage to the generator or engine.

16
 Installation / Initial Set-Up

5. Mount & Connect Generator and Engine

The recommended method to properly mount and connect the generator to the engine is to directly mount
the generator to the engine.

Please reference the adapter plate mounting dimensions below to determine if your engine has the correct
mounting pattern to allow for installation
(see Specification page for shaft requirements)

Adapter Plate
Dimensions
7.12”
6.85”

6.81”
Item #
3.38” 10.41” 1659200

3.58”

1.02”

6.49”

Item #
1659201

1.06”

17
Installation / Initial Set-Up

7.16”

7.08”
Item #
6.50”
1659202

1.06”

18
 Installation / Initial Set-Up
Mounting generator
to engine WARNING:
ALWAYS shut off the engine and
disconnect the spark plug(s) before
installation or servicing the
generator. Make sure all guards
and shields are replaced before
using.

Step 1:
Attach the Engine Adapter
plate to the mounting face
of the engine using the
hardware supplied with the
generator head. Before
tightening the bolts make
sure the adapter plate is
flush against the engine’s
machined surfaces near the
mounting holes. Torque
the bolts to 16 ft lbs.
Misalignment will cause
generator failure.

Step 2:
Carefully slide the
generator head onto the
shaft of the engine. Torque
the bolts from the manual
Capacitor bag to 7.5 ft lbs.
After the bolts are tight,
use a wood block and
“dead-blow” hammer to tap
on the bearing support area
of the non-drive end
bracket (do not damage the
capacitor with hammer).
This will ensure the
bearing is properly seated.

19
Installation / Initial Set-Up

Step 3:
Use the remaining bolt & nut
from the manual bag to secure
the non-drive end bracket.
Slide the head of the bolt into
the U-shaped slot on the
bottom of the non-drive end
bracket. Align the bottom of
the bolt with the existing
isolation bracket. Tighten nut
to secure the generator head.

Step 4:
Remove spark plug(s) or spark
plug wire(s) before working on
the engine or generator to
prevent accidental starting.
Rotor
Stud Install the Rotor Stud into the
rotor through the hole in the
middle of the bearing support
and torque to 16 ft lbs. To
keep the engine from turning
have a helper pull and hold the
engine’s recoil start rope.

Thread the green grounding

screw from the manual bag into
the grounding hole on the cross
bracket of the non-drive end
bracket.

Step 5:
Position the end cover
onto the generator by
rotating the cover so that
the L-shaped slots will
latch onto the screw
heads.

20
 Installation / Initial Set-Up
6. Connecting Generator Wire Harness to Existing Wiring
Follow the detailed wiring sequence to connect the generator wire harness to your existing
generator control panel.

Connect generator
wire harness

To generate 240 Volts: White #2 and White #3 must be connected together.

Main Breaker Total Amps @

Unit Watts
Rating 120V
1659200 3000 12.5 A 25A
1659201 4000 16A 33.3A
1659202 6000 25 A 50A

WARNING: Each circuit receptacle must be protected with a breaker that is

equal or less rating than the receptacle. Failure to do so could result in damage to
equipment powered by the generator and the generator.

Neutral wire should be bonded to ground. Consult your local electrical code.

21
 Installation / Initial Set-Up
7. Ground the generator
Always ensure the generator is properly grounded to prevent electrical shock.
You must always ground the generator by the following method when using the generator as a portable
electrical source:
1) Drive a ¾” or 1” copper pipe or rod into the ground close to the generator. The pipe/rod must
penetrate moist earth – the depth required will be dictated by local soil conditions. Consult with an
electrician.
2) Connect an approved ground clamp to the pipe.
3) Run a 10-gauge wire from the clamp to the generator grounding screw.
4) Do not connect the generator grounding post to a water pipe or a ground used by a radio system.

Screw

10-gauge wire

Pipe/rod

Ground

5) The generator must be grounded every time it is moved.

If a licensed electrician installs the generator with a connection to your building’s electrical circuit for use as a back-up
power system, grounding may alternatively be completed through the building’s grounding system. Ask your
electrician. If the generator is not grounded through your building’s electrical system, follow the procedure above.
WARNING:
Operating the generator when it is not properly grounded can result in electrical shock.

22
 Operation
Once you have set up your generator for use, it is time to start your generator. The following
are the procedures necessary for safe, successful operation of your generator.

Operation Procedures
1. General Safety Rules for Operation
2. Preparing for Operation (Pre-start checklist)
3. Starting the Generator
4. Connecting Loads
5. Stopping
6. Storage & Exercise

Each of these procedures is discussed in detail below:

1. General safety rules for operation

Before starting the generator, review the following general safety rules for operation:

WARNING:
Failure to follow safety rules may result in serious injury or death to the operator or
bystanders.

• Know proper use/how to stop. Be thoroughly familiar with proper use of the equipment and all
generator controls, output receptacles, and connections. Know how to stop the generator quickly if
needed. Refer to the engine manual for engine safety rules and operating instructions.
• Instruct operators. The generator owner must instruct all operators in safe generator set-up and
operation. Only trained adults should set up and operate the generator – Do not let children operate.
• Intended use. Carefully read about and understand the intended use of this generator. Do not use for
other purposes, as unforeseen hazards or equipment damage may result.
• Under the influence. Never operate, or let anyone else operate, the generator while under the influence
of alcohol, drugs, or medication.
• Safety guards / controls. Do not operate the generator unless all safety covers, guards, and barriers are
in place and in good working order, and all controls are properly adjusted for safe operation
• Damaged. Do not operate the generator with damaged, missing, or broken parts.
• Modifications. Do not modify the generator in any way. Modifications can create serious safety hazards
and will also void the warranty.
• Malfunction during operation. Immediately turn off the generator if any of the following conditions
arise during operation:
o Excessive change in engine speed, slow or fast
o Overheating in load connecting devices
o Sparking or arcs from generator
o Loss of electrical output
o Receptacle damage
o Excessive vibration
o Flame or smoke
o Abnormal noise

• Adjusting / repairing Before working on the generator or engine always turn off engine and remove

23
 Operation (cont’d)
spark plug(s) or spark plug wire(s) to prevent accidental starting. Always discharge the capacitor before
working on the generator head to prevent electrical shock. (See Maintenance & Repair section of this
manual for instructions on how to do this.)
• Carbon monoxide poisoning. The running engine gives off carbon monoxide, a poisonous gas that can
kill you. You CANNOT smell it, see it, or taste it. Follow all instructions for site selection and
positioning the generator, and avoid inhaling the exhaust. If you start to feel sick, dizzy, or weak, shut off
the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.
• Electrical cords. Use only UL-listed, outdoor-rated, three prong extension cords of the proper size. All
extension and appliance cords must be in good condition and not worn, bare, frayed, or otherwise
damaged. Use of inadequate or damaged electric cords can cause electric shock or fire.
• GFCI extension cords. Always use ground fault circuit interrupter (GFCI)-equipped extension cords in
damp or highly electrical conductive areas and on construction jobsites to prevent electrical shock.
• Avoid contact. Avoid contact with bare wires, terminals, connections, etc. while the unit is running.
• Wet conditions. Do not operate the generator or handle any electrical equipment while standing in water,
while barefoot, while hands are wet or while in the rain or snow. Electric shock may result.
• Electric shock accident. If an electric shock accident occurs, immediately shut down the source of
electrical power. If this is not possible, attempt to free the victim from the live conductor. Avoid direct
contact with victim. Use a nonconducting implement, such as a dry rope or board, to free the victim from
the live conductor. Apply first aid and get immediate medical help.
• Smoking/sparks. Never smoke near the running generator, and never operate near sources of sparks or
flames.
• Hot parts. Parts of the engine and generator are extremely hot during and after operation and can burn
you. Never touch hot muffler, hot exhaust manifold or any other part of the engine or generator unless
you have first determined if it is hot. Wait a sufficient time for parts to cool before touching any part of
the generator or engine.
• Moving parts. Keep hands, feet, and apparel away from drive belts, sheaves, couplings, fans, and other
moving parts. Never attempt to remove any guard or shield while the unit is operating.

24
 Operation (cont’d)
2. Preparing for Operation (Pre-start checklist)
Mount generator Check that the generator and engine are mounted and connected in
& engine accordance with the instructions given earlier in this manual in the “Installation /
Initial Set-up” section, “Step 5: Mount & Connect Generator to Engine”.
WARNING:
Always ensure generator and engine are properly mounted to avoid
damage and injury to nearby persons, as well as development of sparks
from static electricity.

Position generator Check that the generator is positioned in accordance with the instructions
given earlier in this manual in the “Installation / Initial Set-up” section, “Step 4:
Select a Suitable Site”.
Operate outside only, on dry, level ground with adequate clearance and
ventilation.

DANGER: Carbon monoxide poisoning hazard

The engine gives off carbon monoxide exhaust, a poisonous gas that can
kill. You CANNOT smell it, see it, or taste it. ONLY run generator
OUTDOORS and away from air intakes. NEVER run generator inside
any enclosed or semi-enclosed spaces, including homes, garages,
basements, barns, sheds, boxes, pick-up truck beds, RVs, or boats. These
spaces can trap poisonous gases, EVEN if you run a fan or open
windows.

Ground generator Make sure the generator is grounded in accordance with instructions given
earlier in this manual in the “Installation / Initial Set-up” section, “Step 6:
Grounding the Generator”.
WARNING: Electric shock hazard
Always ensure generator is properly grounded to prevent electrical shock.
IMPORTANT: The generator must be grounded every time it is moved.

Perform regular Make sure that any regular maintenance has been performed:
inspection/
maintenance • On the generator as prescribed in this manual in the “Maintenance &
Repair” section;
• On the engine as prescribed in your engine manual, including
adding/changing the oil.
IMPORTANT:
Under long, continuous-run operating conditions, be prepared to check the engine oil level
every time you refuel the engine. Remember to change the oil at the operating interval
recommended in the engine owner’s manual.

DO NOT start the generator until any needed repairs have been completed.

Check/fill fuel Check the engine fuel level. If needed, fill tank with fresh fuel from a
tank portable container after first reading the following instructions and warnings:

25
 Operation (cont’d)
1) Allow engine to cool for at least two minutes before removing gas cap.
Note: A running or still-hot engine is hot enough to ignite fuel.

2) When adding fuel:

- Use only a UL-approved portable fuel container to transfer fuel. Follow the safety
warning and instructions below for avoiding static electric sparking.
- Do NOT overfill the fuel tank. Allow some space for fuel expansion.
- Fill fuel tank OUTDOORS – never indoors.
- Stay away from all sources of heat, sparks, and flames. Do not smoke.
3) Clean up fuel spills /splashes immediately.
• If possible, move the generator away from spilled fuel on the ground.
• Wipe up spilled fuel, and wait 5 minutes for excess fuel to evaporate before
starting engine.
• Fuel soaked rags are flammable and should be disposed of properly.
• If fuel is spilled on your skin or clothes, change clothes and wash skin
immediately.
4) Store extra fuel in a cool, dry place in an UL-approved, tightly sealed container.
IMPORTANT:
For continuous operation, be prepared to check and refuel the engine on a
regular basis.
SPECIAL HAZARDS DURING FUELING:

WARNING: Fuel fire/explosion hazard

Gasoline is highly flammable and explosive, and standard diesel fuel is
combustible. Heat, sparks, and flames can ignite fuel vapors, which can
become widespread during fueling. A flash fire and/or explosion could
result and cause serious injury or death. Use extreme care when handling
fuel. Carefully follow all the instructions in this section to avoid the
following conditions which could result in fuel vapor ignition:
• fuel vapor collection inside enclosures
• static electric sparks
• sparks from electric wiring, batteries, or running engines
• sources of heat (such as a hot engine or exhaust)
• open flames, including pilot lights

WARNING: Static electric spark hazard

A static electric spark can ignite fuel vapor, resulting in a flash fire that
could cause serious injury or death.
To avoid static electric sparking while filling the fuel tank, the following
steps must be followed to minimize and safely dissipate static electric
charge build-up before and during the fueling process:
• Always dissipate static charge from your body before beginning the
fueling process by touching a grounded metal object at a safe distance
from fuel sources.
• Never fill the generator’s fuel tank directly from the pump – the
generator’s tank is not grounded and high velocity flow from the
pump can cause static electricity build-up. Use an approved portable
container to transfer gas to the generator’s tank.

26
 Operation (cont’d)
• Never fill the portable gas container while it is sitting inside a
vehicle, trailer, trunk, or pick-up truck bed. ALWAYS place
container on the ground to be filled.
• Keep nozzle in contact with portable container while filling.
Manually control the flow of fuel; do NOT use nozzle’s lock-open
device.
• A portable container made of metal or conductive plastic is preferred
because it dissipates charge to ground more readily.

Personal 1. Hearing can be damaged from prolonged, close-range exposure to the type of noise
Protection produced by this generator. The use of ear plugs or other hearing protection
device is recommended for persons working within 15-20 feet of the running
generator for an extended period of time.

2. Loose or dangling apparel and long hair can become quickly entangled in
moving/rotating parts. Metal jewelry can conduct electricity. Never wear jewelry
or loose-fitting clothing such as neckties, scarves, or long-sleeved or untucked
shirts when starting or adjusting the generator. Tie back and secure hair close
to the head.

3. Starting the Generator

After you have completed the pre-start checklist procedures, you are ready to start the
generator.

Start engine Start the engine.

• Before starting, confirm there are no loads connected to the generator’s outlets.
• Follow the instructions provided in your engine manual for starting the engine.

Check output Check output voltage before connecting loads to the generator.
voltage without load
WARNING:
The generator must be run at the correct speed in order to produce the
proper electrical voltage and frequency. Failure to do so could result
in damage to equipment powered by the generator and possible injury
to the individual.
1. Allow running generator to warm up for five minutes. Do not connect any
loads.
2. Use portable voltage meter to check output voltage at the generator’s
outlets/receptacles.
3. Measured voltage should be within the following ranges:
a. 108-132 volts at 120V receptacle(s).
b. 216-264 volts at 240V receptacle(s).
If the output voltage is NOT within the specified range:
1) Adjust the engine speed if possible.
2) If that doesn’t work, re-verify that:
a) Your engine’s rated horsepower meets the minimum requirement,
3) If till t bl t hi t bl t t lt th i

27
 Operation (cont’d)
problem with the engine or the generator. Refer to your engine’s
owner’s manual for troubleshooting. If it appears that the generator
itself is the problem, call NorthStar Product Support @ 1-800-270-0810
for assistance.

4. Connecting Loads
You will want to be careful when connecting loads so as not to overload the generator, especially if
you are powering devices with motors that require a higher starting power load.

Instructions are provided below for connecting loads when you are using the generator:

o As a portable power source

o Connected to a building as a back-up power source

WARNING:
Do not overload generator. Make sure that combined starting and running loads do
not exceed rated capacity of generator. Overloading the generator can cause damage
to the generator and attached electrical devices, and may result in fire.

Using as a Connect electrical loads one at a time according to the following instructions:
Portable Power
Source 1. Allow engine to reach operating speed by allowing it to warm up for
approximately 5 minutes before connecting electrical devices.

2. After engine is warmed up, begin connecting the loads one at a time.

Start with those that require the highest wattage first. The recommended
sequence is as follows:

a. Connect items with motors such as refrigerators, freezers, air conditioners,

or small hand tools, one at a time. Let each motor stabilize before
connecting the next device.
b. Connect any lights you are planning on powering.
c. Connect voltage sensitive equipment such as electronics via surge
protectors. Plug devices such as TV’s, computers, and microwaves into a
UL listed voltage surge protector, then plug the surge protector into the
generator.

3. After connecting all loads, check output voltage again (for generator’s first use,
and periodically after that). Output voltage should remain within the following
ranges:
a. 108-132 volts at 120V receptacle(s).
b. 216-264 volts at 240V receptacle(s).
If output voltage is not within the acceptable range, adjust the engine speed (if
possible). If acceptable output voltage cannot be achieved no matter what the
engine speed, the generator is either overloaded or there is a problem with either
the engine or the generator. Shut off the engine and refer to the Troubleshooting
guide at the end of this manual for assistance with possible problems.

28
 Operation (cont’d)

WARNING:
The generator must be run at the correct speed in order to produce the
proper electrical voltage and frequency. Failure to do so could result in
damage to equipment powered by the generator and possible injury to the
individual.

Note: Expect slight variations in voltage/speed with changing electrical loads.

All engines have a tendency to slow down when a load is applied. When
electrical loads are connected to the generator, the engine is more heavily
loaded and as a result the speed drops slightly.

This slight decrease in speed, together with the voltage drop within the
generator itself, results in a slightly lower voltage when the generator is
loaded to its full capacity than when it is running with no load. Additionally,
there may be small brief surges and drops in voltage as motors connected to
the generator cycle on or off.

The slight variation in voltage has no appreciable effect in the operation of

motors, lights, and most appliances, as long as output voltage remains in the
acceptable range of 108-132 volts at the 120V receptacle(s) and 216-264
volts at the 240V receptacle(s).

Using as a Written instructions for how to safely bring the generator online with the building’s
Back-up Power Source electrical system should be provided by the electrician who installs the transfer
for a Building switch, and who should also provide personal instruction to the owner/operator.

Failure to follow the proper procedure as provided by the electrician could expose
persons to the hazards noted above.
Note: After you have brought the generator online with the transfer switch, you
may need to adjust engine speed to maintain correct output voltage under load.
(See more detail about maintaining proper voltage in the instructions given
above for using the generator as a portable power source.)

5. Stopping
Stop the generator using the following steps:

1. Disconnect all loads to generator.

(Never turn off or reduce engine speed with electrical loads connected. Damage to generator
and loads will occur.)
2. Shut OFF the engine
3. Shut OFF fuel supply to the engine if possible.
4. Remove spark plug to prevent accidental starting of engine.

29
 Operation (cont’d)

6. Storage & Exercise

When you are finished using the generator, you must:
o Make sure all loads to the generator are disconnected and fuel supply is shut off (if possible)
o Store the generator properly
o Plan on exercising the engine regularly unless the generator is prepared for long-term storage.
Detailed instructions are provided below.

Disconnect loads & When you are finished using the generator, disconnect all loads and turn off
shut off fuel supply fuel supply:

1. Make sure all devices that were connected to the generator’s outlets have
been disconnected.
2. Make sure fuel supply to the engine has been shut off, if possible.

Cool engine before Let engine cool for at least five minutes before storing. A hot engine can be a
storing fire hazard.

Choose a storage Store the generator in a location that is:

location o Clean and dry
o Away from sources of heat, open flames, sparks, or pilot lights, even if the
generator’s fuel tank is empty. Residual fuel in the engine’s tank could
ignite.
o Away from extreme high or low temperatures.

Prevent accidental Remove engine spark plug(s) in order to ensure the generator cannot be started
starting accidentally in a storage location or by untrained persons.

Exercise generator The generator should be exercised regularly.

every 4 weeks At least every four weeks, start the engine and let it run for 10 to 15 minutes with a
small load plugged in, such as a lamp or fan.

Monthly exercising of the generator will:

o Dry out any moisture that has accumulated in the windings. If left, this
moisture can cause corrosion in the winding.
o Ensure that the unit is operating properly should it be needed in an
emergency.

Perform regular Perform periodic maintenance as directed in this manual to keep the generator in
maintenance safe working condition.

Prepare engine for If you will not be able to exercise the generator regularly, you must prepare

30
 Operation (cont’d)
long term storage if the engine for long term storage to prevent gum deposits from forming and
needed causing malfunction of the engine.
Prepare engine for long term storage by following instructions in your engine’s
manual or using the following procedure:

o Removing all fuel from the tank and carburetor

OR
o Adding fuel stabilizer to the fuel (following manufacturer’s instructions)
Fuel stabilizer steps:
1. Ensure fuel tank is full.
2. Add fuel stabilizer to fuel tank.
3. Run engine at least 10 minutes after adding stabilizer to allow it to
enter the fuel system.
4. Shut off engine
5. Disconnect spark plug wire and remove spark plug
6. Add one teaspoon oil through spark plug hole
7. Place rag over spark plug hole and turn starter (or pull the recoil) a
few times to lubricate the combustion chamber.
8. Replace spark plug, but do not reconnect the spark plug wire.

31
 Maintenance & Repair
Inspect and maintain your generator as specified below in order to keep it in safe and optimal working
order. Follow all safety rules and recommended maintenance steps.

WARNING
ALWAYS shut off the engine, disconnect the engine’s spark plug(s), and discharge the
capacitor before cleaning, adjusting, or servicing the generator. Make sure all guards and
shields are replaced before using.

Note: The generator head is brushless and maintenance free. The bearing is a heavy-duty sealed ball bearing
which requires no maintenance or lubrication.

Maintenance & Repair

Follow safety rules Read and follow these safety rules whenever you will be servicing the generator:
• Turn off generator. Always turn off generator and remove spark plug(s) or
spark plug wire(s) before working on the engine or generator to prevent
accidental starting.
• Discharge capacitor. When the generator is shut down, the capacitor may
maintain a charge. Always discharge the capacitor before working on the
generator head to prevent electrical shock. Discharge using a screwdriver with an
insulated handle. While wearing safety glasses, touch opposite terminals of the
capacitor together with the tip of the screwdriver. If there is stored charge in the
capacitor, a spark will be generated thereby discharging the capacitor.
• Replace guards. Make sure all guards and shields are replaced after servicing
the generator.
• Repair. Major service, including the installation or replacement of parts, should
be performed only by a qualified electrical service technician. Obtain factory
approved parts from Northern Tool Product Support at 1-800-270-0810.
• Replacement parts. If a part needs replacement, only use factory approved
repair parts. Replacement parts that do not meet specifications may result in a
safety hazard or poor operation of the generator and will void the warranty.

Check receptacles Check receptacles before each use to make sure they are not cracked or broken.
If a receptacle is cracked or otherwise damaged, do not use until replaced with an
authorized factory part. Using cracked or damaged receptacles can be both
dangerous to the operator and destructive to the equipment.

Keep generator clean Keep generator clean.

If dust or debris accumulates on the generator, clean the generator with a damp cloth
or soft bristle brush. Do not allow air intakes to become blocked.
Note: Do not spray generator with a garden hose or pressure washer. Water may enter
the generator and cause damage to the rotor, stator, or internal windings.

Check mounting Check generator mounting on a periodic basis:

1. Make sure that the mounting bolts are tight and secure.

32
 Maintenance & Repair (cont’d)

Perform engine Perform engine maintenance as specified in the engine owner’s manual.
maintenance Engine maintenance items may include:

1. Changing oil and oil filter

2. Air filter check/replacement
3. Spark plug cleaning and replacement
4. Spark arrestor inspection and cleaning
5. Fuel filter check/replacement
6. Fuel tank cleaning
7. Fuel line inspection/replacement
8. Battery charging/maintenance.

IMPORTANT:
If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replace-
ment parts that do not meet specifications may result in a safety hazard or poor operation of the
generator.

Contact NorthStar Product Support at 1-800-270-0810 for any

questions, problems, or parts orders.

33
 Troubleshooting

TROUBLESHOOTING
Problem Possible Causes Possible Remedies
Voltage too low. a) Engine speed too slow. a) Bring generator to a qualified
technician for adjustment.
b) Generator is overloaded. b) Reduce the load. (See Power Load
Planning & Mgt. Section of this
manual.)
Circuit breaker trips. a) Defective load connected to generator. a) Disconnect load.
b) Defective receptacle. b) Replace receptacle.
c) Generator overloaded. c) Reduce the load. (See Power Load
Planning & Mgt. Section of this
manual.)
Voltage too high. a) Engine speed too high. a) Bring generator to a qualified
technician for adjustment.
Generator overheating. a) Generator is overloaded. a) Reduce the load. (See Power Load
Planning & Mgt. Section of this
manual.)
b) Insufficient ventilation. b) Make sure there is at least 7 feet of
clearance on all sides of generator.
No output voltage. a) Defective load connected to generator. a) Disconnect load.
b) Broken or loose wire. b) Bring generator to a qualified
technician for repair.
c) Defective receptacle. c) Replace receptacle.
d) Defective stator. d) Bring generator to a qualified
technician for repair.
e) Defective rotor. e) Bring generator to a qualified
technician for repair.
f) Defective capacitor. f) Bring generator to a qualified
technician for repair.
g) Circuit breaker tripped. g) Reset circuit breaker and reduce
loads connected to the generator.
Engine lacks power. a) Generator is overloaded. a) Reduce the load. (See Power Load
Planning & Mgt. Section of this
manual.)
b) Dirty air filter. b) Clean or replace air filter.

34
 Summary of Important Safety Information (cont’d)
This section provides a summary of the various safety procedures and measures that have been
presented throughout the manual. Keep this summary handy and refer to it to refresh your
memory about how to safely use your generator.

WARNING
Carefully read and make sure you understand the following safety information before using
the generator.
Improper use or maintenance of the generator can result in serious injury or death from
carbon monoxide poisoning, electric shock, entanglement, fire, or burns. In addition, the
generator can lift or flip and cause severe injury if improperly secured.

General
• Read manual. Read this Owner’s Manual and the engine Owner’s Manual completely before attempting to
set-up and use the generator. Serious injury or death can result if safety instructions are not followed.
• Instruct operators. The generator owner must instruct all operators in safe generator set-up and operation.
Do not allow anyone to operate the generator who has not read the Owner’s Manual and been instructed on its
safe use.
• Adults only. Only trained adults should set up and operate the generator. Do not let children operate.
• Under the influence. Never operate, or let anyone else operate, the generator while under the influence of
alcohol, drugs, or medication.
• Intended use. Carefully read about and understand the intended use of this generator. Do not use for other
purposes, as unforeseen hazards or equipment damage may result.

Prohibition Against Modifications

• Modifications prohibited. Never modify or alter the generator in any way. Modifications can create serious
safety hazards and will also void the warranty.
• Fuel/exhaust system. Never modify the engine’s exhaust system, fuel tank, or fuel lines. Carbon monoxide
poisoning, fire, or explosion could result.
• Guards. Do not operate generator unless all guards and cover shields, which prevent access to moving parts
and pinch points, are in place. Failure to guard the power transmission mechanisms may result in serious
injury or death.

Safety – Installation & Set-up

• Mount generator and engine. Failure to properly mount the generator may cause the unit to lift or flip
during use, which could result in severe injury to the operator or bystanders, or cause damage to surrounding
objects.
• The generator and engine must be securely mounted to a common base such as a heavy-duty metal
plate.
• The mounting base must be of adequate size and strength to withstand operating torque and vibration
without either flipping or experiencing stress failure.
• See the “Installation / Initial Set-Up” section of this Owner’s Manual for mounting requirements and
instructions.
• Guarding. Clothing or hair can become rapidly entangled in unguarded rotating parts, resulting in serious
injury or death. The customer is responsible for installing an appropriate guard if applicable.
• Dry, level surface. Situate generator on a dry, firm, level surface. Ensure generator sits level and will not
slide or shift during operation.
• DANGEROUS carbon monoxide exhaust - Operate OUTSIDE only! The engine gives off carbon
monoxide exhaust, a poisonous gas that can kill. You CANNOT smell it, see it, or taste it. ONLY run
generator OUTDOORS and away from building air intakes. NEVER run generator inside homes, garages,
barns, sheds, or other semi-enclosed spaces. These spaces can trap poisonous gases, EVEN if you run a fan or
open windows.

35
 Summary of Important Safety Information (cont’d)
• Cooling ventilation. The generator needs adequate, unobstructed flow of air to allow for proper cooling of
engine and generator head so it does not overheat and possibly cause fire. Situate so there is adequate
clearance around generator to allow for cooling airflow. Do not allow debris to accumulate and block airflow.
Keep all objects at least 7 feet away from vent slots.
• Grounding. Always ensure generator is properly grounded to prevent electrical shock. This generator is
equipped with a grounding screw. Always complete the grounding path from the generator to a copper
pipe/rod driven into moist earth to a sufficient depth. Check with an electrician for local grounding
requirements. If a licensed electrician installs the generator with a connection to your building’s electrical
circuit for use as a standby power system, grounding will be complete through the building’s grounding
system.
• Isolate connection to building’s electrical circuit. Never plug the generator directly into a wall outlet.
ANY connection to a building’s electrical system MUST ISOLATE THE GENERATOR FROM UTILITY
POWER via an UL-approved transfer switch installed by a licensed electrician in compliance with all
applicable local building and electrical codes. If the generator is not isolated from the utility power system by
such means, generator output will back feed into the utility power grid. This may result in injury or death to
utility power workers or others who contact the lines during a power outage. It may also cause the generator
to explode or cause fire when utility power is restored.
• Wet conditions. Water conducts electricity. Do not operate generator where it is wet. Operate on a dry
surface under an open, canopy-like structure.
• Hot engine exhaust. Engine exhaust can be extremely hot and cause fire. Refer to your engine manual to
determine safe clearance distance required between hot exhaust and nearby combustible objects.
• CO alarms. Ensure that working, battery-operated or battery back-up carbon monoxide alarms are used in
any dwelling/structure that is in close proximity to the running generator.
• Fire extinguisher. Keep a fire extinguisher rated “ABC” by the National Fire Protection Association nearby.
Keep it properly charged and be familiar with its use.

Safety – Before Use

Know how to operate
• Review safety rules. Before each use of this generator, review the “Rules for Safe Operation.” Failure to
follow these rules may result in serious injury or death.
• Know how to operate. Be thoroughly familiar with all controls and with the proper use of the equipment.
Know how to stop the generator quickly if needed.
• Inspect. Before each use, inspect the generator, engine. Ensure generator/engine mounting is secure. Check
for fuel leaks and loose or damaged parts. Do not operate the generator with damaged, missing, or broken
parts.

Personal protective equipment

• Hearing protection. The use of ear plugs or other hearing protection device is recommended for those in
close proximity to the generator while it is operating.
• No loose / dangling apparel. Loose or dangling apparel and long hair can become entangled in
moving/rotating parts. Metal jewelry can conduct electricity. Never wear jewelry or loose-fitting clothing
such as neckties, scarves, or long-sleeved or untucked shirts when operating the generator. Tie back hair and
secure close to head.
Battery Safety
(If engine is equipped with battery start)
Batteries are hazardous because they contain caustic acid, can emit explosive gases, and can cause electric shock.
Caution must be exercised when making connections to a battery to avoid shock and contact with the acid, and to
prevent any sparking that could lead to an explosion. Follow safety rules carefully when connecting battery to
engine:
• Eye/skin protection. Always wear eye protection and protective clothing when connecting or disconnecting
battery.
• Sparks/Smoking. Never smoke or work near sparks or other sources of ignition.
• Electric shock. Never touch both battery terminals at the same time with your hand or any non-insulated
tools.

36
 Summary of Important Safety Information (cont’d)
• Connection/disconnection sequence. ALWAYS connect and disconnect cables to the correct battery
terminals in the proper sequence:
o When CONNECTING the battery, connect the RED cable to the POSITIVE terminal FIRST.
o When DISCONNECTING the battery, disconnect the BLACK cable from the NEGATIVE terminal FIRST
• Acid/skin contact. If battery acid contacts skin or clothing, flush immediately with water and neutralize with
baking soda.
Gasoline safety - fueling your engine
Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Use
extreme care when handling:
• Fuel outdoors. Fill fuel tank outdoors – never indoors. Gasoline vapors can ignite if they collect inside an
enclosure. Explosion can result.
• Use approved container. Never pump fuel directly into engine at gas station. Static charge can build and
ignite fuel. Use an UL approved fuel container to transfer gas to the engine.
• Running / hot engine. A running engine is hot enough to ignite fuel. Never add fuel or remove gas cap if
engine is running or still hot. Stop the engine and allow to cool at least two minutes before adding fuel.
• Heat / flames / sparks. Stay away from sources of heat, flame, or sparks while adding fuel.
• Don’t overfill. DO NOT overfill the gas tank. Allow at least 1/2” of empty space below the fill neck to allow
for fuel expansion.
• Replace cap. Replace gas cap securely before starting engine.
• Spills. Clean up fuel spills immediately. Move generator away from spilled fuel on the ground. Wipe fuel
off engine and wait 5 minutes for excess fuel to evaporate before starting engine. Gas soaked rags should be
disposed of properly.
• On skin / clothes. If gasoline is spilled on your skin or clothes, change clothes and wash skin immediately.
• Inspect fuel system. Check fuel system on a regular basis. Look for signs of leaks, deterioration, or
damaged fuel tank. Do not start engine until needed repairs have been completed.
• Gasoline storage. Store gasoline in a cool, dry place in an UL-approved, tightly sealed container.

Safety – During Use

• Safety equipment / controls. Always operate the generator with all safety covers, guards, and barriers in
place and in good working order, and all controls properly adjusted for safe operation.
• Know how to stop. Be thoroughly familiar with proper use of the equipment and all generator controls,
output receptacles, and connections. Know how to stop the generator quickly if needed.
• Power transmission guarding. Never operate the generator without proper guarding of the power
transmission assembly, including all rotating shafts, pulleys, belts, and couplings. Clothing or hair can become
rapidly entangled in unguarded rotating parts, resulting in serious injury or death.
• Check output voltage. Check output voltage to ensure the generator is working properly before connecting
loads to the generator. Failure to do so could result in damage to equipment powered by the generator and
possible injury to the individual. Do not adjust output speed of engine to change voltage. If voltage is not
within specified range, have generator repaired by factory authorized personnel.
• Stabilize before connecting loads. Start generator and let engine stabilize before connecting electrical loads.
• Do not overload. Do not overload the generator. Make sure that combined starting and running loads do not
exceed rated capacity of generator or damage will result.
• Protect sensitive electronics. Some electronic equipment, such as computers and audio/video equipment,
can be damaged by small fluctuations in the flow of power. Use a surge suppressor for any voltage-sensitive
electronic equipment you will be powering with the generator.
• Electrical cords. Use only UL-listed, outdoor-rated, three prong extension cords of the proper size. All
extension and appliance cords must be in good condition and not worn, bare, frayed, or otherwise damaged.
Use of inadequate or damaged electric cords can cause electric shock or fire.
• GFCI extension cords. Always use ground fault circuit interrupter (GFCI)-equipped extension cords to
prevent electrical shock in damp or highly electrical conductive areas and on construction jobsites.
• Wet conditions. Do not operate the generator or handle any electrical equipment while standing in water,
while barefoot, while hands are wet or while in the rain or snow. Electric shock may result.
• Avoid contact. Avoid contact with bare wires, terminals, connections, etc. while the unit is running.
• Electric shock accident. If an electric shock accident occurs, immediately shut down the source of electrical
power. If this is not possible, attempt to free the victim from the live conductor. Avoid direct contact with

37
 Summary of Important Safety Information (cont’d)
victim. Use a nonconducting implement, such as a dry rope or board, to free the victim from the live
conductor. Apply first aid and get immediate medical help.
• Hot parts. Parts of the engine and generator are extremely hot during and after operation and can burn you.
Never touch hot muffler, hot exhaust manifold or any other part of the engine or generator unless you have
first determined if it is hot. Wait a sufficient time for parts to cool before touching any part of the generator or
engine.
• Moving parts. Keep hands, feet, and apparel away from drive belts, sheaves, couplings, fans, and other
moving parts. Never attempt to remove any guard or shield while the unit is operating.
• Smoking/sparks. Never smoke near the running generator, and never operate near sources of sparks or
flames.
• Carbon monoxide poisoning. The engine gives off carbon monoxide, a poisonous gas that can kill you.
You CANNOT smell it, see it, or taste it. If you start to feel sick, dizzy, or weak while using the generator,
shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide
poisoning.
• Malfunction during operation. Immediately turn off the generator if any of the following conditions arise
during operation:
o Excessive change in engine speed, slow or fast
o Overheating in load connecting devices
o Sparking or arcs from generator
o Loss of electrical output
o Receptacle damage
o Engine misfire
o Excessive vibration
o Flame or smoke
o Abnormal noise
• Adjusting / repairing. Before working on the generator or engine, always turn off engine and remove spark
plug(s) or spark plug wire(s) to prevent accidental starting.

Safety – After use

• Cool before storing. Let engine and generator cool for at least five minutes before storing. Hot equipment
can be a fire hazard near combustible materials.
• Prevent accidental starting. When generator is not in use, remove key from engine starter (key start
engines) and secure in a safe location, or remove spark plug(s) or spark plug wires(s) in order to ensure that
generator cannot be started in a storage location or by untrained persons.
• Storage location. Store the generator/engine assembly in a dry location away from sources of heat, open
flames, sparks or pilot lights – such as water heaters, space heaters, furnaces, clothes dryers, or other gas
appliances – EVEN IF the engine’s gas tank is empty. Residual gasoline could ignite.
• Exercise regularly. Exercise generator every four weeks to dry out moisture that accumulates in the
windings. If generator cannot be exercised on a regular basis, prepare generator for long term storage.
• Periodic maintenance. Perform periodic maintenance as directed in this manual to keep the generator in safe
working condition.

Safety - Inspection/Maintenance
Inspect and maintain your generator on a regular basis and repair as needed to keep it in safe working condition:
• Turn off engine. Always turn off engine and remove spark plug(s) or spark plug wire(s) before working on
the engine or generator to prevent accidental starting.
• Discharge capacitor. When the generator is shut down, the capacitor may maintain a charge. Always
discharge the capacitor before working on the generator head to prevent electrical shock.
• Clear debris/deposits. Keep generator head and moving parts clean. This will ensure the generator is in safe
working condition.
• Replace guards / shields. Make sure all guards and shields are replaced after servicing the generator.
• Replacement parts. If a part needs replacement, only use parts that meet the manufacturer’s specifications.
Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the
generator and will void the warranty.

38
 Fastener Identification

(For 1659200, 1659201 & 1659202)

39
 Fastener Identification (cont’d)

Item # 1659200

Item # 1659201
&
1659202

40
 Component List – 1659200A.1

Item # Part # Description Qty

1 780422 Engine Adapter Plate 1
2 780423 Fan & bolts 1
3 31193 Drive End Bracket 1
4 780424 Enclosing Band 1
5 780425 Stator 1
6 780426 Rotor 1
7 307481 Varistor 2
8 780427 Diode 2
9 780428 Securing Stud & nut 1
10 780429 Bearing 1
11 31195 Non Drive End Bracket 1
12 780430 Capacitor 1
13 780431 Bracket Securing Stud 4
14 781874 End Cover 1
15 38271 End Cover Plug 1
16 781829 Wire Harness 1

41
 Component List – 1659201A.1

Item # Part # Description Qty

1 305522 Mount Plate (J609B) 1
2 306404 Fan Bolts 2
3 778953 Fan 1
4 306406 Drive End Bracket 1
5 778954 Enclosing Band 1
6 305554 End Cover 1
7 306408 End Cover Plug 1
8 778955 Stator 1
9 778956 Rotor 1
10 778959 Diode 2
11 778957 Securing Stud 1
12 307485 Bearing 1
14 306417 Non Drive End Bracket 1
15 778958 Capacitor 1
16 778960 Bracket Securing Stud 4
17 778961 Varistor 2
18 781829 Wire Harness 1

42
 Component List – 1659202A.1

Item # Part # Description Qty

1 779919 Mount Plate (J609B) 1
2 779556 Fan Bolts 2
3 779557 Fan 1
4 779920 Drive End Bracket 1
5 779786 Enclosing Band 1
6 777304 End Cover 1
7 38271 End Cover Plug 1
8 779787 Stator 1
9 779788 Rotor 1
10 307481 Varistor 2
11 779789 Diode 2
12 779790 Securing Stud + Nut 1
13 38276 Bearing 1
14 38278 Non Drive End Bracket 1
15 779791 Capacitor 1
16 779792 Bracket Securing Stud 4
17 781829 Wire Harness 1

43
 Limited Warranty
Dear Valued Customer:
The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product
properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for
quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high
quality piece of machinery it is. Neglect and improper handling may impair its performance. Please thoroughly read the
instructions and understand the operation before using your product.

Limited Warranty
NorthStar shall warranty any piece of equipment manufactured, or parts of equipment manufactured, to be free from
defects in material or workmanship for a period of:

Item # Warranty Period

1659200
90 days for residential/commercial/rental use from the date of
1659201
purchase by user
1659202

NorthStar shall warranty any wear item, including, but not limited to, valves, seals, pump diaphragms, hoses, and filter
elements to be free from defects in material or workmanship for a period of 90 days from the date of purchase by user.
This warranty applies to the original purchaser of the equipment and is non transferable. Verification of purchase is the
responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the equipment has failed due to
lack of proper maintenance. Any misuse, abuse, alteration or improper installation or operations will void warranty.
Determining whether a part is to be replaced or repaired is the sole decision of NorthStar.
NOTE: Some services performed by parties other than NorthStar may void warranty.
This warranty covers parts only. It will not provide for replacement of complete products due to defective parts.
Components not manufactured by NorthStar are guaranteed by their manufacturer and can be serviced at factory-
authorized locations near you. Any costs incurred due to replacement or repair of items outside of a NorthStar approved
facility is the responsibility of the buyer and not covered under warranty. NorthStar can supply you with the service center
location in your area.
This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood,
windstorm, acts of God, applications not approved by NorthStar in writing, corrosion caused by chemicals, use of
replacement parts which do not conform to manufacturer’s specifications, and damage caused by vandalism. Additional
exclusions: loss of running time, inconvenience, loss of income, or loss of use, including any implied warranty of
merchantability of fitness for a specific use.
Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical
contact by the public. This warranty does not cover any personal injury or damage to surrounding property caused by
failure of any part.
This warranty is in lieu of any other warranty expressed or implied and NorthStar assumes no other responsibility or
liability outside that expressed within this warranty.

Please fill in the following information and have it on hand when you call in on a warranty claim.

Customer Number: ______________________________________________________________

Date of Purchase: _______________________________________________________________

NorthStar Serial Number: _______________________________________________________

Item Number: __________________________________________________________________

44
This page has intentionally been left blank.

45
 ®

Manufactured by
Northern Tool + Equipment Co.,
2800 SouthCross Drive West
P.O. Box 1499 Burnsville, MN 55337-0499

46