Scribd
Upload
138 views

PID Short Questions

A controller continuously monitors the error between a measurement variable and desired setpoint, and provides an output to adjust the process variable and reduce the error. Key terms include proportional band, which is the range of error over which the controller output is proportional. Gain is inversely proportional to proportional band. Controller action can be direct, where output increases with measurement, or reverse. Reset action integrates proportional action over time to reduce steady-state error. Batch controllers quickly return output to the control range when deviations end.

Uploaded by

66umer66
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
138 views

PID Short Questions

A controller continuously monitors the error between a measurement variable and desired setpoint, and provides an output to adjust the process variable and reduce the error. Key terms include proportional band, which is the range of error over which the controller output is proportional. Gain is inversely proportional to proportional band. Controller action can be direct, where output increases with measurement, or reverse. Reset action integrates proportional action over time to reduce steady-state error. Batch controllers quickly return output to the control range when deviations end.

Uploaded by

66umer66
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

1.What is a ‘controller’? Where are its application areas?

A controller is an instrument used for controlling a process variable


(measurement). Its continuously monitors the error signal and gives a corrective
output to the final control element.

2.Explain the following terms in a controller?


Measurement variable: It is the demand variable measured and controlled.
Desired Variable: it is the demand signal (setpoint) to which the process
variable is controlled.
Deviation: it is the error signal caused by the difference between the
measurement and the demand signal.
Output: It is the corrective signal from the controller to the final control element.

3.Explain what is ‘direct action’ and ‘reverse action’ on a controller?


Direct action : In a direct acting controller, the output increases when the
process measurement (variable) increases.
Reverse action : In a reverse action controller, the output decreases when the
process measurement (variable) increases.

4.What is a gap controller?


A controller whose output changes from ;minimum to maximum (on-off) and
vice-versa when the error signal (deviation) exceeds the set gap depending on
the controller action.

5.What is a ‘proportional band’? Explain with an example?


It is the range in percentage for which the controller output changes
proportionally from minimum to maximum and vice-versa when the
measurement deviates from the setpoint.

For example: A controller set at 50% proportional band

The controller output changes from minimum to maximum and vice-versa when
the measurement exceeds 25% either side of the setpoint depending on the
controller action.

6.What is a ‘gain’? Write the relation (formula) between a gain and


proportional band?
A controller ‘gain’ is inversely proportional to its proportional band.
. g=(1/p)*100
. g=gain
. P = proportional band
7.What is a ‘reset action’? Explain with an example?
Reset action in a controller is the integration of the proportional action by the
set period. The reset action repeats the proportional action’s output per the
reset time set, until the error signal becomes zero or the output gets saturated.

For example :if the reset action is set for 30 sec.

For a 0.5 volt correction output ;by the proportional action will be repeated by
the reset action every 30 secs., until the error signal becomes zero or the output
gets saturated.

8.What is a ‘batch’ facility on a controller?


Whenever a deviation persists for a long time the controller output saturates at
the maximum of minimum output (-2.5 VDC or + 12.5 VDC/0 kPa or 140 kPa)
depending on the controller action. In a normal controller when the process
reverts to normal the output takes its time to come into control range.

In a batch controller the output reverts to the control limit (0VDC OR 10.00V DC
20 kPa or 100 kPa) as soon as the deviation enters the batch limits

9.What will be the output (increases or decreases) of a direct action


controller when the process goes above the setpoint?
In a direct acting controller, the controller output increases when the process
(measurement) goes above the setpoint)

10.What will be the output of a reverse acting controller when the process
changes from 50% to 75% where the proportional band is set at 50%,
setpoint is set at 50%?
The controller output will be zero.

11.What is a ‘bump-less transfer’ in a controller’s auto/manual change


over?
‘Bump-less transfer’ is to eliminate the change in the controller’s output when
the controller is changed from auto to manual control and vice-versa.

12.Explain how to change a controller from auto to manual and vise-


versa?
Pneumatic controllers : While taking the controller from auto to manual, the
manual output is to be balanced to the auto output and then transfer the auto-
manual switch to manual. While changing the controller from manual to auto,
the controller setpoint is matched to the manual output and then auto-manual
switch is transferred.
Electronic controllers : Auto to manual control may be transferred directly as
the electronic circuit keeps the auto and manual output matched. But while
changing the controller from manual to auto, the controller setpoint is to match
to the process variable and then auto-manual switch is transferred.
13.What type of controller (P, PI, PID) is preferred on the following process
control loops?
Pressure: If the load change is minimum, then a proportional controller is
suitable. If a frequent load change is expected then a Proportional + Integral
controller is preferred.
Level : Normally a proportional controller is preferred.
Flow: Proportional + Integral controller is preferred
Temperature: Proportional + Integral + Derivative controller is preferred

14.what are the advantages and disadvantages of BANG BANG


Controller?

Advantages:

1. Simple/cheap to implement
2. Hugely better performance than open loop
3. Needs only primitive actuators

Disadvantages:

1. Performance (higher drag)


2. Increase of tension on the plant i.e. suddenly turning plant off and on
reduces the over all plant life

15.why we use BANG BANG controller even knowing all defects?

Because its response time is cheap simple and batter as compared to other
controller

You might also like