Scribd
Upload
73 views2 pages

M-Bond 600: Other Accessories Used in An M-Bond 600 Installation

Uploaded by

pietro zugnoni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
73 views2 pages

M-Bond 600: Other Accessories Used in An M-Bond 600 Installation

Uploaded by

pietro zugnoni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

M-Bond 600

Strain Gage Adhesive


OTHER ACCESSORIES USED IN AN
M-BOND 600 INSTALLATION:
• CSM Degreaser or GC-6 Isopropyl Alcohol
• Silicon-Carbide Paper
• M-Prep Conditioner A
• M-Prep Neutralizer 5A
• GSP-1 Gauze Sponges
• CSP-1 Cotton Tip Applicators
• MJG-2 Mylar® Tape
• TFE-1 Telon® Film
• HSC Spring Clamp
• GT-14 Pressure Pads and Backup Plates

DESCRIPTION
Similar to M-Bond 610 except with more reactive curing reaction time. Cure must begin within 30 minutes of
agent. Shorter shelf life, pot life, and working time than application (up to 4 hours for M-Bond 610).
M-Bond 610, but has lower temperature cures and faster

CHARACTERISTICS
PARAMETER DETAILS

OPERATING TEMPERATURE Short Term: –452° to +700°F (–269° to +370°C).


RANGE Long Term: –452° to +500°F (–269° to +260°C).

ELONGATION CAPABILITIES 1% at –452° (–269°C), 3% at +75°F (+24°C), 3% at +500°F (+260°C).

Minimum 3 months from date of manufacture on the label when stored unmixed at +75°F (+24°C);
SHELF LIFE or minimum 9 months from the date of manufacture on the label when stored unmixed refrigerated
upon receipt at +40°F (+5°C). Refrigerated storage recommended. Refer to product label.

POT LIFE 2 weeks at +75°F (+24°C); 4 weeks at +40°F (+5°C).

10 to 70 psi (70 to 480 kN/m2)


CLAMPING PRESSURE
Optimum: 30 to 40 psi (200 to 275 kN/m2)

Moderately Elevated-
Temperature Cure Required.
Recommended Postcure:
CURE REQUIREMENTS* 1 to 2 hours at 50°F (30°C)
above maximum operating
temperature.

PACKAGING
KIT SINGLE MIX KIT
4 bottles (11 g ea) Curing Agent 1 bottle (11 g ea) Curing Agent
4 bottles (8 g ea) Resin 1 bottle (8 g ea) Resin
4 brush caps for dispensing mixed adhesive 1 brush cap for dispensing mixed adhesive
4 disposable mixing funnels 1 disposable mixing funnel

* References: Instruction Bulletin B-130, “Strain Gage Installations with M-Bond 43-B, 600 and 610 Adhesive Systems,” included in
each kit.

www.micro-measurements.com For technical questions, contact 2373-EN


32 [email protected] Rev 24-Jan-2020
Legal Disclaimer Notice
Vishay Precision Group, Inc.

Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in
any other disclosure relating to any product.

The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but
not limited to, the warranty expressed therein.

VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.
To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the
application or use of any product, (ii) any and all liability, including without limitation special, consequential or
incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,
non-infringement and merchantability.

Information provided in datasheets and/or specifications may vary from actual results in different applications and
performance may vary over time. Statements regarding the suitability of products for certain types of applications
are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s
responsibility to validate that a particular product with the properties described in the product specification is suitable for
use in a particular application. You should ensure you have the current version of the relevant information by contacting
VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.

No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any
conduct of VPG.

The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do
so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.
Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such
applications.

Product names and markings noted herein may be trademarks of their respective owners.

Copyright Vishay Precision Group, Inc., 2014. All rights reserved.

Document No.: 63999 www.vpgsensors.com


Revision: 15-Jul-2014 1

You might also like