Scribd
Upload
78 views

يجوملا موقملا Rectifier

Here are the voltage waveforms and average value calculation for the full-wave rectified voltage shown in the figure: - The voltage waveforms across each half of the center-tapped secondary winding would be half of the transformer secondary voltage, with opposite polarity during each half cycle. - The voltage waveform across RL would be the full-wave rectified voltage, with the same polarity during each half cycle, as current flows through one diode then the other each half cycle. - The average value of the full-wave rectified voltage is calculated as: VAVG = 2*Vp(out) / π Where Vp(out) is the peak output voltage after the diode drops are accounted for.

Uploaded by

Yacine Khalid
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
78 views

يجوملا موقملا Rectifier

Here are the voltage waveforms and average value calculation for the full-wave rectified voltage shown in the figure: - The voltage waveforms across each half of the center-tapped secondary winding would be half of the transformer secondary voltage, with opposite polarity during each half cycle. - The voltage waveform across RL would be the full-wave rectified voltage, with the same polarity during each half cycle, as current flows through one diode then the other each half cycle. - The average value of the full-wave rectified voltage is calculated as: VAVG = 2*Vp(out) / π Where Vp(out) is the peak output voltage after the diode drops are accounted for.

Uploaded by

Yacine Khalid
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

‫المقوم الموجي‬

‫‪Rectifier‬‬
Index
• Introduction
• Types of rectifiers
• Half-wave rectifier
• Full-wave rectifier
• Center-tapped full-wave rectifier
• Bridge full-wave rectifier
Introduction
All active electronic devices require a source of constant dc that can be
supplied by a battery or a dc power supply. The dc power supply converts
voltage available at wall outlets into a constant dc voltage. The dc power
supply is one of the most common circuits you will find, so it is important to
understand how it works. A basic block diagram of the complete power
supply is shown in Figure 1.
Generally the ac input line voltage is stepped down to a lower ac voltage
with a transformer (although it may be stepped up when higher voltages are
needed or there may be no transformer at all in rare instances). A transformer
changes ac voltages based on the turns ratio between the primary and
secondary. If the secondary has more turns than the primary, the output
voltage across the secondary will be higher and the current will be smaller. If
the secondary has fewer turns than the primary, the output voltage across the
secondary will be lower and the current will be higher. The rectifier can be
either a half-wave rectifier or a full-wave rectifier. The rectifier converts the ac
input voltage to a pulsating dc voltage, called a half-wave rectified voltage, as
shown in Figure (1). The filter eliminates the fluctuations in the rectified
voltage and produces a relatively smooth dc voltage. The regulator is a circuit
that maintains a constant dc voltage for variations in the input line voltage or
in the load. Regulators vary from a single semiconductor device to more
complex integrated circuits. The load is a circuit or device connected to the
output of the power supply and operates from the power supply voltage and
current.
Types of rectifiers
Rectifier

Half-wave rectifier Full-wave rectifier

Center-tapped Bridge
Half-wave rectifier
Figure (2) illustrates the process called half-wave rectification. A diode is
connected to an ac source and to a load resistor, RL, forming a half-wave
rectifier. Keep in mind that all ground symbols represent the same point
electrically. Let’s examine what happens during one cycle of the input voltage
using the ideal model for the diode. When the sinusoidal input voltage (Vin)
goes positive, the diode is forward-biased and conducts current through the
load resistor, as shown in part (a). The current produces an output voltage
across the load RL, which has the same shape as the positive half-cycle of the
input voltage.
When the input voltage goes negative during the second half of its cycle,
the diode is reverse-biased. There is no current, so the voltage across the load
resistor is 0 V, as shown in Figure (2b). The net result is that only the positive
half-cycles of the ac input voltage appear across the load. Since the output
does not change polarity, it is a pulsating dc voltage with a frequency of 60
Hz, as shown in part (c).
The average value of the half-wave rectified output voltage is the value you
would measure on a dc voltmeter. Mathematically, it is determined by finding
the area under the curve over a full cycle, as illustrated in Figure (3), and then
dividing by the number of radians in a full cycle. The result of this equation
shows that VAVG is approximately 31.8% of Vp for a half-wave rectified
voltage.
When the practical diode model is used with the barrier potential of 0.7 V
taken into account, this is what happens. During the positive half-cycle, the
input voltage must overcome the barrier potential before the diode becomes
forward-biased. This results in a half-wave output with a peak value that is 0.7
V less than the peak value of the input, as shown in Figure (3). The expression
for the peak output voltage is:
Vp(out) = Vp(in) - 0.7
And the average value:
VAVG = Vp(out) / π
Full-wave rectifier
A full-wave rectifier allows unidirectional (one-way) current through the
load during the entire of the input cycle, whereas a half-wave rectifier allows
current through the load only during one-half of the cycle. The result of full-
wave rectification is an output voltage with a frequency twice the input
frequency and that pulsates every half-cycle of the input, as shown in Figure
(4).

The average value of the full-wave rectified is: VAVG = 2*Vp(out) / π


Center-tapped full-wave rectifier
A center-tapped rectifier is a type of full-wave rectifier that uses two diodes
connected to the secondary of a center-tapped transformer, as shown in
Figure (5). The input voltage is coupled through the transformer to the
center-tapped secondary. Half of the total secondary voltage appears
between the center tap and each end of the secondary winding as shown.
The basic operation of a center-tapped full-wave rectifier shown in
Figure (6).
For a positive half-cycle of the input voltage, the polarities of the
secondary voltages are as shown in Figure (6a). This condition forward-biases
diode D1 and reverse-biases diode D2. The current path is through D1 and
the load resistor RL, as indicated. For a negative half-cycle of the input
voltage, the voltage polarities on the secondary are as shown in Figure (6b).
This condition reverse-biases D1 and forward-biases D2. The current path is
through D2 and RL, as indicated. Because the output current during both the
positive and negative portions of the input cycle is in the same direction
through the load, the output voltage developed across the load resistor is a
full-wave rectified dc voltage, as shown in Figure (6).
In any case, the output voltage of a center-tapped full-wave rectifier is
always one-half of the total secondary voltage less the diode drop, no matter
what the turns ratio.
Vp(out) = (Vp(sec.) / 2) - 0.7
Vp(sec.) = n* Vp(pri)
Bridge full-wave rectifier
the operation of a bridge rectifier shown in Figure (7).
The bridge rectifier uses four diodes connected as shown in Figure (7).
When the input cycle is positive as in part (a), diodes D1 and D2 are forward-
biased and conduct current in the direction shown. A voltage is developed
across RL that looks like the positive half of the input cycle. During this time,
diodes D3 and D4 are reverse-biased.
When the input cycle is negative as in Figure (7b), diodes D3 and D4 are
forward biased and conduct current in the same direction through RL as
during the positive half-cycle. During the negative half-cycle, D1 and D2 are
reverse-biased. A full-wave rectified output voltage appears across RL as a
result of this action.
Two diodes are always in series with the load resistor during both the
positive and negative half-cycles. If these diode drops are taken into account,
the output voltage is:

Vp(out) = Vp(sec.) – 1.4

Vp(sec.) = n * Vp(pri.)
.H.W
• Show the voltage waveforms across each half of the
secondary winding and across RL.
• Find the average value of the full-wave rectified
voltage in Figure.

You might also like