Service Manual

Color Television

CHASSIS : CN-200I/A
NTSC-M SYSTEM
MODEL: DTQ-26S1FC/FS/FSP(CN-200I)
DTQ-29S1FCN/FSN/FSP(CN-200I)
DTQ-26S1HC/HS/HSP(CN-200A)
DTQ-29S1HC/HS/HSP(CN-200A)

DAEWOO ELECTRONICS CO., LTD.

OVERSEAS SERVICE DEPT.

Downloaded from www.Manualslib.com manuals search engine

 FEATURES
FS (Frequency Synthesizer) Tuning System
CATV Ready
Monitor Look Design
A/V IN. (Stereo)
Stereo/Mono Function

ELECTRICAL SPECIFICATIONS
POWER INPUT
FC SERIES AC 120V 60Hz
FS SERIES AC 85V ~ AC 150V 60Hz
FSP SERIES AC 220V 50Hz/60Hz
POWER RATING
26” MODELS 100W
29” MODELS 105W
INTERMEDIATE FREQUENCIES
PICTURE IF CARRIER FREQUENCY 45.75MHz
SOUND IF CARRIER FREQUENCY 41.25MHz
COLOR SUB CARRIER FREQUENCY 42.17MHz
AUDIO OUTPUT RATING 1.2W 2
SPEAKER 2W 8 ohm 2
ANTENNA INPUT IMPEDANCE VHF/UHF 75 ohm UNBALANCED
TUNING RANGES
VHF 2 THRU 13
UHF 14 THRU 69
CATV 1 THRU 125

CONTENTS
Safety Precautions 3
Control View 5
Important Service Notes 7
Block Diagram 8
General Adjustments 10
Trouble Shooting Charts 12
Description of Semiconductors 20
Printed Boards 21
Exploded View 23
Schematic Diagram 25
Parts List 27
Option List 36

Downloaded from www.Manualslib.com manuals search engine

 CONTROL VIEW

F-CONNECTOR

300 OHM-75 OHM

COUPLING
TRANSFORMER

VHF

75Ω

FROM 75 OHM
VHF ANTENNA WITH
CABLE OR CABLE
TV SYSTEM

Downloaded from www.Manualslib.com manuals search engine

 1. Overview of Your Equipment

Your TV comes with a remote control. The section below summarizes the buttons,controls, and terminals
that you will use with your TV.

2. Your TV' s Front Panel

1. POWER
Use this buttom to turn your TV on or off.
2. CH
Use these buttom to change channels on your TV, or to select items in the menu system.
3. VOL
Use these buttom to change your TV s volume, to activate selections in the menu system, or to
change audio and video settings.
4. MENU
Use this buttom to turn the TV s menu system on and off.
5. Remote control receiver
This receiver receives a signal from your remote control. Do not block it.

3. Your TV' s Back Panel

1. Antenna terminal
Use this terminal to attach an antenna or cable
system to your TV.

2. VIDEO IN
This terminal allows the TV to receive a video
signal from another components, such as a VCR.

1 2 4 3 3. AUDIO R/MONO IN
This terminal allows the TV to receive an audio
R/MONO signal from another components, such as
a VCR.

4. AUDIO L IN
This terminal allows the TV to receive an audio L
signal from another components, such as a VCR.

Downloaded from www.Manualslib.com manuals search engine

 BLOCK DIAGRAM (CN-200I)

Downloaded from www.Manualslib.com manuals search engine

 BLOCK DIAGRAM (CN-200A)

Downloaded from www.Manualslib.com manuals search engine

 GENERAL ADJUSTMENTS
1. GENERAL clockwise.)
In the majority of cases, all color televisions will need only 4) Rotate the RED, GREEN and BLUE BIAS controls (R917,
slight touch-up adjustment upon installation. Check the basic R918, R919) counterclock wise from the maximum, set
characteristics such as height, focus and sub- basic them to the position where notches in the knobs become
characteristics such as height, focus and sub- bright. Observe parallel to the surface of P.C. Board.
the picture for good black and white details without 5) Set the GREEN and BLUE DRIVE controls (R920, R921)
objectionable color shading. to the mid position.
2. VERTICAL HEIGHT ADJUSTMENT 6) Turn the service switch SW901 (Service Position) on the
CRT board.
1) Tune in an active channel. 7) Rotate the SCREEN control (on T402) gradually
2) Adjust brightness and contrast controls for a good picture. clockwise until the second horizontl line following the first
3) Adjust vertical height control (R305) for approximately one line appears slightly on the screen. Then turn fully
half inch over scan at top and bottom of picture screen. counterclockwise the two BIAS controls corresponding to
4) Vertical centering adjustment R310 the colors of the first and the second horizontal lines to
Horizontal centering adjustment R516. eliminated the lines.
3. FOCUS ADJUSTMENT 8) Set the SCREEN control to the position where the third
1) Tune in an active channel. horizontal line lights slightly on the screen.
2) Adjust brightness, sharpness and contrast controls for a 9) Adjust the two BIAS control set to the minimum in item 7)
good picture. above to obtain the slightly lighted horizontal line in the
same levels of three (red, green, blue) colors. (The line
3) Adjust focus control (part of T402) for sharp scanning lines
should be white if the BIAS controls are adjusted
and/or sharp picture.
properly.)
4. RF AGC ADJUSTMENT
10) Turn the service switch SW901 again (Normal position on
1) Tune in an active channel. the CRT board.)
2) Using the attenuator, apply the signal of 60dBm to the 11) Press PICTURE-SEL, P-UP and set the brightness and
antenna input terminal. contrast controls to the maximum.
3) Turn RF AGC control (R113) full clockwise until snow 12) Adjust the BLUE and GREEN DRIVE control to obtain
or/and noise appears in the picture, then slowly turn control proper white-blanced picture in high light areas.
counter clockwise until snow or/and noise disappears.
13) Using P-SEL, P-DN key, set the brightness and contrast
5. HIGH VOLTAGE CHECK controls to obtain dark gray raster. Then check the white
High voltage is not adjustable but must be checked to verify balance in low brightness. Of the white balance is not
that the receiver is operating within safe and efficient design proper, retouch the BIAS controls and DRIVE controls to
limitations as specified: obtain a good white balance in both low and high light
1) Operate Receiver for at least 15 minutes at 120V AC line. areas.
2) Set brightness sharpness, contrast and color control to 8. MAIN B+(103V) ADJUSTMENT
minumum position (Zero beam). 1) Tune in an active channel
3) Connect accurate high voltage meter to CRT anode. The 2) Check TP10 (DC 103V Line) using D.V.M
reading should be 26kv~28kv 3) Adjust voltage control (R809) for main B+(DC 103V)

If a correct reading cannot be obtained, check circuity for 9. SUB-BRIGHTNESS ADJUSTMENT

malfunctioning components.
1) Tune in a color program.
6. X-RADIATION PROTECTION CIRCUIT TEST 2) Set the CONTRAST control to maximum and the
When service has been performed on the horizontal BRIGHTNESS control to maximum and the
deflection system, high voltage system or B+system, the X- SHARPNESS control to the center position.
RADIATION protection circuit must be tested for proper 3) Set the COLOR and TINT controls to center.
operation as follows: 4) Set the SUB-BRIGHT control R522 to center and
1) Operate receiver for at least 15 minutes at 120V AC line. leave the receiver on five minutes in this state.
5) Watching the picture carefully, adjust the SUB-
2) Adjust all customer controls for normal picture and sound.
BRIGHT control in the position where the picture does
3) Short R414(X-RAY Short test), and remove short clip.
not show evidence of blooming in high brightness area
4) If the operation of horizontal osc. does not stop in step and not appear too dark in low bright area.
The circuit must be repaired, before the set is returned to
the customer. 6) Check for BRIGHTNESS controls at both extremes.

7. CRT GRAY SCALE ADJUSTMENT 7) If the picture does not appear dark with the
CONTRAST and BRIGHTNESS control turned to
1) Tune in an active channel.
minimum, or not appear bright with the controls turned to
2) Set the COLOR control to minimum.
maximum, adjust the SUB-BRIGHT control again for an
3) Turn the SCREEN control (on T402 fully counter- acceptable picture.

10

Downloaded from www.Manualslib.com manuals search engine

 10. PICTURE IF/AFT ADJUSTMENTS
NOTE : THIS RECEIVER IS TRANSISTORIZED AND SPECIAL CARE MUST BE TAKEN WHEN SERVICING. READ
THE FOLLOWING (NOTES BEFORE ATTEMPTING ALIGNMENT)
Alignment requires an exacting procedure and should be undertaken only when necessary.
Isolation transformer must be used to prevent shock hazard.
The test equipment specified or its equivalent is required to perform the alignment properly. Use of equipment which
does not meet these requirements may result in improper alignment.
Accurate equipment is essential to obtain proper alignment of this receiver.
Use of excessive signal from a sweep generator can cause overloading of receiver circuit Overloading should be
avoided to obtain a true response curve. Insertion of markers from the marker generator should not cause distortion of
the response curve.
The AC Power line voltage should be kept 120 volts while alignment is being performed.
Do not attempt to disconnect any components while the receiver is in operation.
Make sure the power cord is disconnected before replacing any parts in the receiver.

TEST EQUIPMENT
Digital voltmeter National Model VP-2600A or equivalent
Oscilloscope Tektronix Model 2215A or equivalent.
Direct/Low-capacity probe Tektronix Model P6120 or equivalent
(Accessory of oscilloscope)
Color-Bar/Dot/Crosshatch generator Tektronix Model 146 or equivalent.
PIF sweep marker generator Nihon Tsushinki Model 4723 or equivalent
Power supply Academy Model 150A or equivalent
Isolation transformer Voltage adjustable type having capacity of
at least 150 watts
BLOCK DIAGRAM

B+ MAIN BOARD OSCILLOSCOPE

BIAS
TP3 TP7
POWER
SUPPLY TP6
A TP5 Y
X
(12V)

45.75MHz
AGC
Fig. 6 PIF Response
BIAS PIF SWEEP/MARKER GEN.
POWER
SUPPLY
B
(4-5V)
V H DETIN OUT
P 45.75MHz

Fig. 5 Picture IF Sweep Alignment Fig. 7 AFT Response Curve

1) Disconnect the TUNER IF output from TP6 and connect equipment as shown above.
2) Set the sweep/marker generator for 30 Vrms.
3) Observe 1 Vp-p on scope by adjusting power supply B (4~5V).
4) Adjust PIF coil L505 for according beat signal with 45.75 MHz marker on scope (See Fig. 6).
5) Connect the DET IN to TP7.
6) Adjust AFT coil L504 for center display at 45.75 MHz on scope (See Fig. 7).
7) After completing the above steps, disconnect equipment and adjust the AGC delay circuit as explained in the General
Adjustments section of this manual.

11

Downloaded from www.Manualslib.com manuals search engine

 TROUBLE SHOOTING CHARTS

NO POWER

YES GO TO A
DOES QC701(POWER ON/OFF TR)
OPERATE?
NO
GO TO B

A
CHECK
#30
(7.5V DC)
R816 15K
2WATT DOES
30 SHUT DOWN
CIRCUIT
OPERATE?
I501
24
CHECK TP10 103VDC
26
(MAIN B+
LINE)
IF #26 NORMAL
& NO OUTPUT AT
#23 THEN Q402
CHANGE I501 H. OUTPUT CHECK
Q402
COLLECTOR

D406
12V 12V T402
F.B.T

CHECK
12V LINE
D403 103V(B+)

CHECK
ALL THE POINTS
B THEN CHANGE
NORMAL: 5V I701
QC706 RESET: 0V
RESET
SHOULD 16 I701 PWR
BE 36 CONTROL
4.3V-5.2V 12 LC864616A 42 KEY

5V
Q802 OPEN LOAD KEY OPERATE?
REGULATOR THEN CHECK CHECK DIODE
R808 #42 ON STATE D701 & SWITCH
4 ~5V KEY BOARD
CHECK
F801 QC701
125V 5A T801
POWER
CHECK CONTROL
LEAD
SOLDERING

L801
LINE FILTER

12

Downloaded from www.Manualslib.com manuals search engine

 NO PICTURE
OK
CHECK THE WAVE FORM OF GO TO C
I501 #44 (2Vp-p)
NG
GO TO D

H
C
COMPOSITE 21
FC VIDEO INPUT FS I501
H LA 7674
Y-OUT QC501
VIDEO
DRIVE
QC201 42
C506

CONTRAST 39 CHECK
210V
CHECK
CONTROL BRIGHT H. BLANKING KINE
31
(NORMAL) 11 14
VOLTAGES
#39: 5.0V T402
D505 R522 FBT D404
#31: 3.9V SUB-BRIGHT CHECK
ABL
9V LINES R413
ABL H.T
#11,14
CHECK
ABL R412
Ib = 1.2mA

D
AGC CHECK
HEATER
6.3Vrms
ENA 9V
DATA
U101 TUNER VT (33V)
CLK

5V
IF

I701
LC864616A ADJUST
RF-AGC
10 11 R113 DETECTOR
OUTPUT

Z101 8 10
SAW FILTER 9 I501 44 TO QC201
LA7674
CHECK CHECK 2 11 14
CSB503E IF AGC
VTG. H
5VDC
TP2
CHECK
9V LINE
#11, 14

13

Downloaded from www.Manualslib.com manuals search engine

 NO SOUND(CN-200I)
CHECK FOR SIGNAL GO TO E
AT I501 #1

GO TO F

E CHECK #1
MONO 100% MOD
-> 0.424 Vp-p #2 9V(B+)
I601

#19
CHECK 1Vp-p
CHECK #12 #18
EXT SOUND
SIGNAL OFF:L #13 (MUTE)#17 MUTE ON: 5V
OFF: 0V

#1 9V(B+) #4
CHECK 1Vp-p
#2(0~5V) #6
I602

#8(0~5V)

#7 CHECK 12VDC
I604/I603
CHECK SOUND INPUT #3 #6

#5 CHECK SOUND OUTPUT

#11 #1 COMPOSITE SIGNAL

CHECK 9V I601 #1
#14

#44 I501
LA7674

#4 CHECK FM DET
CIRCUIT
Z201 #48

CHECK SOUNDIF INPUT

14

Downloaded from www.Manualslib.com manuals search engine

 NO SOUND(CN-200A)
CHECK FOR SIGNAL GO TO E
AT I501 #1

GO TO F

E
#38 #22

CHECK #30 9V(B+) #21 CHECK 4.5V

MONO 100% MOD #20
#2(9VDC)
-> 0.693 Vp-p
IM601

L OUT
#15 CHECK R/L OUTPUT
R OUT
#39 #13
CHECK 4.5V #40 (MUTE)#8 MUTE ON: 5V
OFF: 0V

#1 9V(B+) #4
CHECK 1Vp-p
#2 (0~5V) #6
I602

#8 (0~5V)

#7 CHECK 12VDC
I604/I603
CHECK SOUND INPUT #3 #6

#5 CHECK SOUND OUTPUT

#11 #1 COMPOSITE SIGNAL

CHECK 9V I601 #1
#14

#44 I501
LA7674

#4 CHECK FM DET
CIRCUIT
Z201 #48

CHECK SOUND IF INPUT

15

Downloaded from www.Manualslib.com manuals search engine

 CH DON'T STOP

CHECK INPUT SIGNAL GOOD GO TO G

CONDITIONS
BAD LOSS OF SIGNAL OR
WEAK SIGNAL

IF OUTPUT
8, 9 I501
U101 LA7674
TUNER
CHECK 45
AFT WINDOW ADJUST
RF AGC AFT
VTG. 10 46
1.6V ~ 3.4V R113
2 3 4
9
PIF
8
13 47
I701
LC864616A
ADJUST
PIF & AFT
33 REFER TO GENERAL
L: NO SIGNAL ADJUSTMENTS
H: SIGNAL

44

S.D SIGNAL
DETECTION

16

Downloaded from www.Manualslib.com manuals search engine

 NO COLOR

CHECK
9VDC
CENTER
3.5V

11
TINT 41

12 APC FILTER
COLOR 36
X502
13
CENTER
4V I501
CHECK
LA7674
CRYSTAL
CHECK 3.579545MHZ
COMPOSITE 9VDC
VIDEO C506
42 14
R-Y
18 Q901 R
FS
G-Y
19 Q902 G
QC201
Emitter B-Y
20 Q903 B

+
FC LUMINANCE (-Y) VIDEO B (210V)
21
CHECK
CONNECTOR
P901

NO VERTICAL DEFLECTION

CHECK 9VDC CHECK 9VCC

14 CHECK
VERT.OUT
1
I501
I301
LA7674
LA7837
CHECK 25VDC
28 2
4 12 8
R301
R304 D402 R417

VR305 V,HEIGHT R305

C413

C307 C417
R311 +
CHECK THE WAVEFORM
V.D.Y. I301 #12 NO OUTPUT:
CHANGE IC301

17

Downloaded from www.Manualslib.com manuals search engine

 ON SCREEN DISPLAY DOES NOT OPERATE

CHECK
FOR,60Hz

/ VS 19 21
R

G R, G, B, BL
22 CHANGE
/ HS 20 I701 B
23
BL
24
IF OSD DOES NOT
10 11 OPERATE, CHANGE
I701
CHECK
FOR, 15, 734Hz
OSC CHECK

REMOTE CONTROL DOES NOT OPERATE

IL01
REMOCON
SENSOR

GND 5V OUT

CHECK
WAVE-
FORM

34
I701 LC864616A

18

Downloaded from www.Manualslib.com manuals search engine

 PIN ASSIGN OF IC LC864616A(I701)

VIDEO MUTE(O) 1 P10 P07 42 POWER(O)

KEY OUT
DATA(O) 2 P11 P06 41
KEY OUT
CLOCK(O) 3 P12 P05 40
KEY OUT
ENABLE(O) 4 P13 P04 39
KEY IN
SOUND MUTE(O) 5 P14 P03 38 3-LAN SAP TV/VID
KEY IN
TV/VIDEO(O) 6 P15 P02 37 MN/ST EEPROM
KEY IN
MPX1(O) 7 P16 P01 36 CH UP VOL + POWER
KEY IN
MPX2(O) 8 P17 P00 35 CH DN VOL - MENU

9 DVss P73/INT3/TOIN 34 REMOCON(IN) : Switch

10 CF1 P72/INT2/TOIN 33 SD(IN) : Option

Diode
11 CF2 P71/INT1 32 X-Ray IN

12 DVdd P70/INT0 31 AC 60Hz IN

AFC IN 13 P90/AN0 PWM5 30 CONTRAST

N. C 14 P91/AN1 PWM4 29 BRIGHTNESS

N. C 15 P92/AN2 PWM3 28 COLOR

16 /RESET PWM2 27 TINT

17 FILT PWM1 26 SHARPNESS

1Vpp IN
18 CVIN PWM0 25 VOLUME

19 /VS BL 24

20 /HS B 23

21 R G 22

NOTE) CF is used 503KHz RESONATOR

19

Downloaded from www.Manualslib.com manuals search engine

 TROUBLE SHOOTING CHARTS

NO POWER

YES GO TO A
DOES QC701(POWER ON/OFF TR)
OPERATE?
NO
GO TO B

A
CHECK
#30
(7.5V DC)
R816 15K
2WATT DOES
30 SHUT DOWN
CIRCUIT
OPERATE?
I501
24
CHECK TP10 103VDC
26
(MAIN B+
LINE)
IF #26 NORMAL
& NO OUTPUT AT
#23 THEN Q402
CHANGE I501 H. OUTPUT CHECK
Q402
COLLECTOR

D406
12V 12V T402
F.B.T

CHECK
12V LINE
D403 103V(B+)

CHECK
ALL THE POINTS
B THEN CHANGE
NORMAL: 5V I701
QC706 RESET: 0V
RESET
SHOULD 16 I701 PWR
BE 36 CONTROL
4.3V-5.2V 12 LC864616A 42 KEY

5V
Q802 OPEN LOAD KEY OPERATE?
REGULATOR THEN CHECK CHECK DIODE
R808 #42 ON STATE D701 & SWITCH
4 ~5V KEY BOARD
CHECK
F801 QC701
125V 5A T801
POWER
CHECK CONTROL
LEAD
SOLDERING

L801
LINE FILTER

12

Downloaded from www.Manualslib.com manuals search engine

 NO PICTURE
OK
CHECK THE WAVE FORM OF GO TO C
I501 #44 (2Vp-p)
NG
GO TO D

H
C
COMPOSITE 21
FC VIDEO INPUT FS I501
H LA 7674
Y-OUT QC501
VIDEO
DRIVE
QC201 42
C506

CONTRAST 39 CHECK
210V
CHECK
CONTROL BRIGHT H. BLANKING KINE
31
(NORMAL) 11 14
VOLTAGES
#39: 5.0V T402
D505 R522 FBT D404
#31: 3.9V SUB-BRIGHT CHECK
ABL
9V LINES R413
ABL H.T
#11,14
CHECK
ABL R412
Ib = 1.2mA

D
AGC CHECK
HEATER
6.3Vrms
ENA 9V
DATA
U101 TUNER VT (33V)
CLK

5V
IF

I701
LC864616A ADJUST
RF-AGC
10 11 R113 DETECTOR
OUTPUT

Z101 8 10
SAW FILTER 9 I501 44 TO QC201
LA7674
CHECK CHECK 2 11 14
CSB503E IF AGC
VTG. H
5VDC
TP2
CHECK
9V LINE
#11, 14

13

Downloaded from www.Manualslib.com manuals search engine

 NO SOUND(CN-200I)
CHECK FOR SIGNAL GO TO E
AT I501 #1

GO TO F

E CHECK #1
MONO 100% MOD
-> 0.424 Vp-p #2 9V(B+)
I601

#19
CHECK 1Vp-p
CHECK #12 #18
EXT SOUND
SIGNAL OFF:L #13 (MUTE)#17 MUTE ON: 5V
OFF: 0V

#1 9V(B+) #4
CHECK 1Vp-p
#2(0~5V) #6
I602

#8(0~5V)

#7 CHECK 12VDC
I604/I603
CHECK SOUND INPUT #3 #6

#5 CHECK SOUND OUTPUT

#11 #1 COMPOSITE SIGNAL

CHECK 9V I601 #1
#14

#44 I501
LA7674

#4 CHECK FM DET
CIRCUIT
Z201 #48

CHECK SOUNDIF INPUT

14

Downloaded from www.Manualslib.com manuals search engine

 NO SOUND(CN-200A)
CHECK FOR SIGNAL GO TO E
AT I501 #1

GO TO F

E
#38 #22

CHECK #30 9V(B+) #21 CHECK 4.5V

MONO 100% MOD #20
#2(9VDC)
-> 0.693 Vp-p
IM601

L OUT
#15 CHECK R/L OUTPUT
R OUT
#39 #13
CHECK 4.5V #40 (MUTE)#8 MUTE ON: 5V
OFF: 0V

#1 9V(B+) #4
CHECK 1Vp-p
#2 (0~5V) #6
I602

#8 (0~5V)

#7 CHECK 12VDC
I604/I603
CHECK SOUND INPUT #3 #6

#5 CHECK SOUND OUTPUT

#11 #1 COMPOSITE SIGNAL

CHECK 9V I601 #1
#14

#44 I501
LA7674

#4 CHECK FM DET
CIRCUIT
Z201 #48

CHECK SOUND IF INPUT

15

Downloaded from www.Manualslib.com manuals search engine

 CH DON'T STOP

CHECK INPUT SIGNAL GOOD GO TO G

CONDITIONS
BAD LOSS OF SIGNAL OR
WEAK SIGNAL

IF OUTPUT
8, 9 I501
U101 LA7674
TUNER
CHECK 45
AFT WINDOW ADJUST
RF AGC AFT
VTG. 10 46
1.6V ~ 3.4V R113
2 3 4
9
PIF
8
13 47
I701
LC864616A
ADJUST
PIF & AFT
33 REFER TO GENERAL
L: NO SIGNAL ADJUSTMENTS
H: SIGNAL

44

S.D SIGNAL
DETECTION

16

Downloaded from www.Manualslib.com manuals search engine

 NO COLOR

CHECK
9VDC
CENTER
3.5V

11
TINT 41

12 APC FILTER
COLOR 36
X502
13
CENTER
4V I501
CHECK
LA7674
CRYSTAL
CHECK 3.579545MHZ
COMPOSITE 9VDC
VIDEO C506
42 14
R-Y
18 Q901 R
FS
G-Y
19 Q902 G
QC201
Emitter B-Y
20 Q903 B

+
FC LUMINANCE (-Y) VIDEO B (210V)
21
CHECK
CONNECTOR
P901

NO VERTICAL DEFLECTION

CHECK 9VDC CHECK 9VCC

14 CHECK
VERT.OUT
1
I501
I301
LA7674
LA7837
CHECK 25VDC
28 2
4 12 8
R301
R304 D402 R417

VR305 V,HEIGHT R305

C413

C307 C417
R311 +
CHECK THE WAVEFORM
V.D.Y. I301 #12 NO OUTPUT:
CHANGE IC301

17

Downloaded from www.Manualslib.com manuals search engine

 ON SCREEN DISPLAY DOES NOT OPERATE

CHECK
FOR,60Hz

/ VS 19 21
R

G R, G, B, BL
22 CHANGE
/ HS 20 I701 B
23
BL
24
IF OSD DOES NOT
10 11 OPERATE, CHANGE
I701
CHECK
FOR, 15, 734Hz
OSC CHECK

REMOTE CONTROL DOES NOT OPERATE

IL01
REMOCON
SENSOR

GND 5V OUT

CHECK
WAVE-
FORM

34
I701 LC864616A

18

Downloaded from www.Manualslib.com manuals search engine

 PIN ASSIGN OF IC LC864616A(I701)

VIDEO MUTE(O) 1 P10 P07 42 POWER(O)

KEY OUT
DATA(O) 2 P11 P06 41
KEY OUT
CLOCK(O) 3 P12 P05 40
KEY OUT
ENABLE(O) 4 P13 P04 39
KEY IN
SOUND MUTE(O) 5 P14 P03 38 3-LAN SAP TV/VID
KEY IN
TV/VIDEO(O) 6 P15 P02 37 MN/ST EEPROM
KEY IN
MPX1(O) 7 P16 P01 36 CH UP VOL + POWER
KEY IN
MPX2(O) 8 P17 P00 35 CH DN VOL - MENU

9 DVss P73/INT3/TOIN 34 REMOCON(IN) : Switch

10 CF1 P72/INT2/TOIN 33 SD(IN) : Option

Diode
11 CF2 P71/INT1 32 X-Ray IN

12 DVdd P70/INT0 31 AC 60Hz IN

AFC IN 13 P90/AN0 PWM5 30 CONTRAST

N. C 14 P91/AN1 PWM4 29 BRIGHTNESS

N. C 15 P92/AN2 PWM3 28 COLOR

16 /RESET PWM2 27 TINT

17 FILT PWM1 26 SHARPNESS

1Vpp IN
18 CVIN PWM0 25 VOLUME

19 /VS BL 24

20 /HS B 23

21 R G 22

NOTE) CF is used 503KHz RESONATOR

19

Downloaded from www.Manualslib.com manuals search engine

 DESCRIPTION OF SEMICONDUCTORS
LA7674 (VIF/SIF/VIDEO/CHROMA/DEFLECTION)
1. Case Outline : SDIP 52P
2. Pin Connections/Block Diagram

IC501 LA7674
IF/VIDEO/CHROMA/DEF

LOCK APC
FM DET 1 DET DET 52 IFAPC

IF AGC 2 51 VCD
VIDEO
VCO
DET
EX AIN 3 50 VCO

FM DET 4 49 RF AGC
VIDEO
AMP
NFB 5 48 SIF IN
FM- FM- LIM
AOUT 6 DET
ATT
DET AMP 47 AFT OUT

GND 7 46 AFT
AFT

IF IN 8 45 AFT
VIF
AMP
IF IN 9 44 VDET
RF-
RF AGC 10 AGC 43 AV S.W

VCC 11 IF- 42 IN VIN

AGC

APC 12 APC
41 TINT

VXO 13 VCO 40 EX. VIN

VCC 14 TINT ACC 39 CONT

KILL-
ER
RIN 15 38 VIDEO

GIN 16 OSD 37 GND

2NA IST
BPA BPA
BIN 17 36 COLOR

R-Y 18 35 BDET
BLACK
OSD-SWITCH

CARRIER-F

EXPAND
COLOR
DEMO

G-Y 19 34 YIN

B-Y 20 33 SHARP
CONTRAST
FBT-DET

SHARP
-Y OUT

SOFT

-Y 21 32 CLAMP
FBT-
FBPIN 22 DET 31 BRIGHT
DRIVER

FBT-DET
-Y OUT

HOUT 23 30 VCCH
HOR

AFC CLAMP
2 BRIGHT D.L

HOD 24 29 S. SEP
VER
HOR SYNC/
HOR
OSC

HOSC 25 C/D SEP

SYNC-
SEP
VER
C/D
28 V. OUT

HAFC 26 AFC HOR 27 H.DET

1 COIN

20

Downloaded from www.Manualslib.com manuals search engine

 DTQ-26S1FC/FS/FSP/HC/HS/HSP
EXPLODED VIEW

23

Downloaded from www.Manualslib.com manuals search engine

 DTQ-29S1FCN/FSN/FSP/HC/HS/HSP
EXPLODED VIEW

24

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine