DESIGN DATA

APPLICABLE CODE & STANDARD ASME SEC.VIII DIV.1 2019 ED. & API 661 7th ED.
MATERIAL SYSTEM SPECIFICATION 32-SAMSS-011- (21 JULY 2019)
ASME CERTIFICATION (DESIGNATOR) YES(U)
NATIONAL BOARD REGISTRATION NO
3012.0 FLUID NAME LIGHT HC, H2S, CO2, H2O
LETHAL SERVICE NO
SPECIAL SERVICE NO
1535.0 UNIT / BAY / BUNDLE 4/2/2
DESIGN PRESSURE (INT./EXT.) 180/- psi(G)
DESIGN TEMPERATURE (INT./EXT.) 370/- °F
767.5 767.5

198.0
OPERATING (INLET) PRESSURE 144 psi(G)
OPERATING TEMPERATURE (INLET/OUTLET) 331 / 121 °F
1525.0 1525.0
MIN. DESIGN METAL TEMP. [MDMT] 43 °F

60.0
4622011 4620103 JOINT EFFICIENCY, E 0.85 (HEADERS), NOTE-6, NOTE-8
CORROSION ALLOWANCE (HEADER/TUBES) 0.125 / 0 IN
IMPACT TEST EXEMPTED AS PER UCS 66 (a) & (c)
MAX. ALLOW. WORKING PRESSURE (HOT & CORRODED) 209 psi(G) AT 370 °F
610.0

MAX. ALLOWABLE PRESSURE [MAP NEW & COLD] 389 psi(G) AT 89 °F psi(G)
HYDROSTATIC TEST PRESSURE 313 psi(G)
POSTWELD HEAT TREATMENT [PWHT] YES (HEADER BOX ONLY)
TUBE TO TUBESHEET JOINT EXPANSION + 2 GROOVES
NDE FOR HEADER BOX "UT, AS PER THE GENERAL NOTE-8" / RT FOR BUTT JOINT
4622012
WEIGHT PER BUNDLE (EMPTY / FULL WATER) 27,426 / 33,883 LB
MATERIALS
767.5 767.5 HEADER CARBON STEEL, (SA-516 GR. 70)
TUBE CARBON STEEL, (SA-179)
FIN ALUMINUM, (ASTM-B221-A-1060-F)
3050.0
3050.0 NOZZLE FLANGE CARBON STEEL, (SA-105 N)
NOZZLE PIPE CARBON STEEL, (SA-106 Gr. B)
SHOULDER PLUG CARBON STEEL, (SA-105 N)
VIEW A-A SECTION B-B COUPLING CARBON STEEL, (SA-105 N)

SCALE 4/ 50 SCALE 4 / 50 FINNED TUBE DATA

TUBE MATERIAL SA-179

O.D 38.1 (1.5") x t 2.16 (0.085") x 12192 (40')L

TUBE DIMENSION
O.D 25.4 (1.0") x t 2.16 (0.085") x 12192 (40')L
A B FIN MATERIAL ALUMINUM, (ASTM-B221-A-1060-F)
FIN TYPE EXTRUDED
O.D 69.85(2.75") x t 0.4064(0.016") x 394(10FPI)FIN/M
FIN DIMENSION
O.D 57.15(2.25") x t 0.4064(0.016") x 394(10FPI)FIN/M
12289.0±5 TUBE Q'TY / ONE BUNDLE 186 (1.0") & 77 (1.5") / 263 TOTAL
No. OF PASS / ROWS 2/6

NOZZLE DATA
MARK N.P.S SCH. Thk Q'ty RATING FACE SERVICE REMARKS
N1 8" 80 12.7 1 ASME CL.150 WN. RF INLET SET ON TYPE, NOTE-10
N2 8" 80 12.7 1 ASME CL.150 WN. RF INLET SET ON TYPE, NOTE-10
928.0±5

N3 6" 120 14.27 1 ASME CL.150 WN. RF OUTLET SET ON TYPE, NOTE-10

610.0
N4 6" 120 14.27 1 ASME CL.150 WN. RF OUTLET SET ON TYPE, NOTE-10
N5 1" - - 1 ASME CL.6000 FC. - VENT FC WITH ROUND PLUG
N6 1" - - 1 ASME CL.6000 FC. - DRAIN FC WITH ROUND PLUG

12500.0

A THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

GENERAL NOTES:
10. WHEN NOZZLES ARE INSTALLED ONTO OR ENCROACHING A CORNER WELD IN THE HEADER, 100% UT SHALL BE PERFORMED IN
1. BILL OF MATERIAL SHOWS FINISHED SIZES AND NECESSARY CUTTING & MACHINING ALLOWANCE SHALL BE ADDED AS PER
THE CORNER WELD PRIOR TO THE INSTALLING THE NOZZLE. THE CORNER WELD SHALL BE SUBJECTED TO 100% UT AFTER
SHOP PRACTICES.
INSTALLATION OF NOZZLE ALSO. MP TESTING SHALL BE PERFORMED ON THE ROOT PASS AND FINAL PASS OF THE WELD
2. GASKET SEATING SURFACE OF ALL FLANGES SHALL BE OF 125-150 AARH FINISH. JOINTS ATTACHING THE NOZZLE.
3. ALL PRESSURE PARTS AND PARTS WELDED TO PRESSURE PARTS, LOAD BEARING MEMBERS AND & NON-PRESSURE PARTS
11. ALL SHARP EDGES OF THE HEADERS SHALL BE ATLEAST ROUNDED TO 3 MM.
SHALL BE CERTIFIED ACCORDING TO EN 10204 - 3.1.
12. SERVICE GASKETS SHALL BE USED FOR HYDROTEST. TEST GASKETS ARE ALLOWED FOR NOZZLE OPENINGS, EXCEPT FOR
4. IMPACT TEST: EXEMPTED AS PER UCS 66 (A), (C). IMPACT TESTING EXEMPTION OF UG-20(F), UCS-66(B)(1) AND (3), UCS-68(C),
WITH BLINDS, GASKETS SHALL BE SPIRAL WOUND SS-304L WITH SOLID CS OUTER RINGS FOR NOZZLE PROVIDED WITH
UG-84(B)(2) AND BY REFERENCE TO TABLE UG-84.4 ARE NOT PERMITTED. BLIND FLANGES.
5. RADIOGRAPHY: FULL RADIOGRAPHY IS APPLICABLE FOR BUTT WELD (C-JOINTS) BETWEEN NOZZLE PIPE AND NOZZLE FLANGES. 13. HT IS NOT REQUIRED AS WHOLE HEADER WILL BE SUBJECTED TO PWHT.
6. THE JOINTS FOR THE HEADER BOX ARE TYPE (7) "CORNER JOINTS WITH FULL PENETRATION WELD" FROM THE TABLE UW-12.
FOR JOINT TYPE (7) & CATEGORY C, FROM THE TABLE UW-12, THE DEGREE OF RADIOGRAPHIC EXAMINATION IS 14. POST WELD HEAT TREATMENT CYCLE- (PWHT REQUIRED FOR HEADER BOXES ONLY)
"NOT APPLICABLE". MOREOVER, FROM NOTE (5) OF TABLE UW-12, JOINT EFFICIENCY OF NOT GREATER THAN 1.00 SHALL BE a. LOADING TEMPERATURE =400 °C (MAX)
USED. b. RATE OF HEATING =200±10 °C/hr.
7. ULTRASONIC TEST: PRESSURE PARTS PLATES HAVING THICKNESS 16 MM TO 50 MM (BOTH INCLUSIVE) SHALL BE c. SOAKING TEMPERATURE & TIME =610±10 °C FOR 80 MINUTES
ULTRASONICALLY TESTED (UST) AS PER ASTM A-435. PRESSURE PART PLATES HAVING THICKNESS ABOVE 50 MM AND ALL d. RATE OF COOLING =260±10 °C/hr
PLATES TO BE USED FOR TUBESHEET AND PLUGSHEET SHALL BE ULTRASONICALLY TESTED (UST) AS PER ASTM A-578 LEVEL B. e. UNLOADING TEMPERATURE =400 °C. FOLLOWED BY COOLING IN STILL AIR.
NO LAMINATION OR INCLUSIONS SHALL BE PERMITTED. 15. HEADERS, SHALL BE COATED AS PER APCS-26T.
8. FOR CORNER WELD JOINTS IN HEADER PLATES UT SHALL BE DONE AS PER API-661. FOR CATEGORY-D JOINTS 100% UT SHALL 16. BUNDLE FRAME AND STRUCTURAL ITEMS SHALL BE HOT DIP GALVANIZED AS PER ASTM-123.
BE DONE. FOR CORNER JOINTS PT/MT SHALL BE DONE AS PER UG-93(D)(3). 17. ALL DIMENSIONS ARE IN MILLIMETER UNLESS OTHERWISE NOTED. ASME
9. BEVELED EDGES OF CARBON STEEL PLATES WITH THICKNESS 25 MM OR HIGHER SHALL BE MAGNETIC PARTICLE OR LIQUID 18. THE EQUIPMENT SHALL MEET API 661 TOLERANCE AND ASIC'S STANDARD TOLERANCE GUIDE, ASIC-STD-01.
PENETRANT EXAMINED AFTER CUTTING FOR LINEAR DISCONTINUITIES. DEFECT SHALL NOT EXCEED LIMITS AS PER SA-20. 19. REFER TOLERANCE STANDARD, PIP VEFN-1100.
20. AS PER FIGURE UW-13.2(r). SHALL HAVE A 3MM (MAX) POSITIVE PENETRATION.
21. ALL BUNDLE STRUCTURE SHALL BE HOT DIP GALVANIZED, FOR SHIPPING AND RUN TEST STRUCTURE WILL BE BLACK
OR PIRMER COATED.
 12 NAME PLATE SA-516/A 36 2 - t10 x 230 x 290
11 NOZZLE FLANGE SA-105 N 2 - 8" ASME CL.150 WNRF
10 NOZZLE PIPE SA-106 Gr. B 2 - 8" SWAGED NOZZLE x SCH 80 x 175.5L
9 PLUG GASKET SOFT IRON 93 - O.D 47.5 x I.D 42.7 x t 1.5
8 PLUG BOLT SA 105 N 93 - 1-5/8" x 12 UNF x 25 L
7 SLIDE PLATE SA-240-316 2 - t6 x 90 x 150
6 STOPPER SA-516/A 36 2 - t12 x 50 x 55
5 END PLATE SA-516 Gr. 70 2 - t20 x 100 x 105
4 BOTTOM PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012
1535.0
3 TOP PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012

2921.0 2 PLUGSHEET SA-516 Gr. 70 1 - t25 x 140 x 3012

1 TUBESHEET SA-516 Gr. 70 1 - t25 x 140 x 3012

767.5 767.5 Q'ty WEIGHT

PART No. PART NAME MATERIAL /BUNDLE DIMENSIONS
(kg)

11
BILL OF MATERIAL
N1 N2 8

12 7

95.0
95.0
45.5 10

398.0
63.5 6 45.5
3 40.0

1
1"-XX TUBES
140.0

100.0
140.0
2
1"-XX TUBES
60.0
31.0 5
4 7
31.0 2857.5 77.3 105.0
77.3
f f 155.0

3012.0

N1 N2 8 9
157.9

60
±
12.7

63.5
105

±
THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
315.4 SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
NOTE: DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
1. THE TOLLERANCE IS (+/-)15 mm. WITHOUT EXPRESS WRITTEN PERMISSION.

6 7
6 mm Thick
f f

Ø20.0 R10.0
30.0

150.0
55.0

Ø6.0 ASME
12.0
50.0
90.0
8" 150# 11380 26680 16020 6100 12200 4480
 15 NOZZLE FLANGE SA-105 N 2 - 8" ASME CL.150 WNRF
14 NOZZLE PIPE SA-106 Gr. B 2 - 6" SWAGED NOZZLE x SCH 120 x 130.6L
13 PLUG GASKET SOFT IRON 172 - O.D 36.0 x I.D 30.0 x t 1.5
12 PLUG GASKET SOFT IRON 172 - O.D 47.5 x I.D 42.7 x t 1.5
11 PLUG BOLT SA 105 N 172 - 1-1/8" x 12 UNF x 25 L
10 PLUG BOLT SA 105 N 172 - 1-5/8" x 12 UNF x 25 L
9 SLIDE PLATE SA-240-316 2 - t6 x 100 x 175
8 SLIDE PLATE SA-240-316 2 - t6 x 100 x 175
7 STOPPER SA-516/A 36 2 - t12 x 50 x 55
6 STRAY PLATE SA-516 Gr. 70 1 - t12 x 105 x 2972
5 END PLATE SA-516 Gr. 70 2 - t20 x 105 x 260
4 BOTTOM PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012

3012.0 3 TOP PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012

2 PLUGSHEET SA-516 Gr. 70 1 - t25 x 300 x 3012
155.0 2921.0 1 TUBESHEET SA-516 Gr. 70 1 - t25 x 300 x 3012
105.0 31.0 Q'ty WEIGHT
PART No. PART NAME MATERIAL DIMENSIONS
31.0 /BUNDLE (kg)
8 3
C D BILL OF MATERIAL
63.5

1
45.5
300.0
260.0

45.0
45.5
154.0

6 5
518.0

1"-XX TUBES

60.0
77.2 77.3
76.2 6.0 1"-XX TUBES
2 14

73.0
100.0

300.0
7 4
9
1.5"-XX TUBES

72.0
58.2 58.2

15 1.5"-XX TUBES
N3 N4 96.3
767.5 767.5

50.0
96.3

2819.4
DETAIL C DETAIL D
SCALE 0.30 : 1 SCALE 0.30 : 1

N3 N4 10 11 12 13
105

208.5
130.6

14.27

NOTE:
1. THE TOLLERANCE IS (+/-)15 mm.

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD

72.0
WITHOUT EXPRESS WRITTEN PERMISSION.

60
±
±
76.2 63.5
± ±

6 7 8 9

f f
Ø6.0
2972 Ø20.0 R10.0 Ø6.0
85
30.0

150.0

100.0

Ø65±3
55.0
105

6MM THICK

6MM THICK
ASME
12.0
22856=102*28: 29 Holes 65.0
50.0
90.0 6" 150# 8000 10060 10060 4280 6100 3260
 15 COUPLING PLUG SA-105 N 2 - 1" 6000LB ROUND PLUG
14 COUPLING SA-105 N 2 - 1" NPT 6000LB FULL COUPLING
13 PLUG GASKET SOFT IRON 172 - O.D 36.0 x I.D 30.0 x t 1.5
12 PLUG GASKET SOFT IRON 172 - O.D 47.5 x I.D 42.7 x t 1.5
11 PLUG BOLT SA 105 N 172 - 1-1/8" x 12 UNF x 25 L
10 PLUG BOLT SA 105 N 172 - 1-5/8" x 12 UNF x 25 L
8 SLIDE PLATE SA-240-316 2 - t6 x 65 x 100
7 STOPPER SA-516/A 36 2 - t12 x 50 x 55
6 STRAY PLATE SA-516 Gr. 70 2 - t12 x 105 x 2972
5 END PLATE SA-516 Gr. 70 2 - t20 x 105 x 412
N4 4 BOTTOM PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012
3 TOP PLATE SA-516 Gr. 70 1 - t20 x 105 x 3012
2 PLUGSHEET SA-516 Gr. 70 1 - t25 x 452 x 3012
3012.0 1 TUBESHEET SA-516 Gr. 70 1 - t25 x 452 x 3012
Q'ty WEIGHT
155.0 PART No. PART NAME MATERIAL DIMENSIONS
f f /BUNDLE (kg)

70.0
70.0 BILL OF MATERIAL
F 15 3 7
E 45.5
14 63.5
45.5

50.0
134.0
6
1 1"-XX TUBES

60.0
77.2 77.3
6 2
5
452.0

412.0
1"-XX TUBES

60.0
1"-XX TUBES

60.0
45.5

181.0
1"-XX TUBES

73.0
77.2

1.5"-XX TUBES

76.2 6.0

72.0
14 4 8 58.2 58.2

15 105.0 1.5"-XX TUBES

96.3
96.3

N5
DETAIL F DETAIL E
SCALE 0.30 : 1 SCALE 0.30 : 1

N5 N6 10 11 12 13

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD

72.0
WITHOUT EXPRESS WRITTEN PERMISSION.

60
±
±
76.2 63.5
± ±

6 7 8

2972 f f
65.0
85 Ø20.0 R10.0
30.0

Ø65±3 Ø6.0
55.0
105

100.0

ASME
22856=102*28: 29 Holes 12.0
50.0
 NOTES :-

1. ALL DIMENSIONS ARE IN mm, UNLESS OTHERWISE SPECIFIED.

2. FINS TO BE EXTRUDED FROM 4.9mm THICK ALUMINUM MUFF

TO GIVE 394 FINS/M WITH A NOMINAL FIN OD OF 57.15mm
FOR 1" TUBE AND 69.85mm FOR 1.5" TUBE.
3. QUANTITY/BUNDLE - 186 (1.0") & 77 (1.5") / 263

FIN TUBE DETAILS (1") :-

FIN TYPE : EXTRUDED

TUBE MOC : SA 179 SEAMLESS TUBE
TUBE LENGTH : 12192 (40')L
TUBE THK: 2.16 (0.085")
TUBE O.D : 25.4 (1")
FIN MOC : ALUMINUM, (ASTM-B221-A-1060-F)
FIN HEIGHT : 15.875 (0.625)
FIN THK : 0.4064 (0.016")
FIN O.D : 57.15 (2.25")
FIN DENSITY : 394 FINS/M , (10 FINS/INCH)

TUBE SUPPORT DETAIL:-

MOC : Aluminum
SUPPORT THK: 1 mm
QTY/BUNDLE : 2976 (8x2/Tube)

FIN TUBE DETAILS (1.5") :-

FIN TYPE : EXTRUDED

TUBE MOC : SA 179 SEAMLESS TUBE
TUBE LENGTH : 12192 (40')L
TUBE THK: 2.16 (0.085")
TUBE O.D : 38.1 (1.5")
FIN MOC : ALUMINUM, (ASTM-B221-A-1060-F)
FIN HEIGHT : 15.875 (0.625)
FIN THK : 0.4064 (0.016")
FIN O.D : 69.85 (2.75")
FIN DENSITY : 394 FINS/M , (10 FINS/INCH)

TUBE SUPPORT DETAIL:-

MOC : Aluminum
SUPPORT THK: 1 mm
QTY/BUNDLE : 1232 (8x2/Tube)

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

TUBE SUPPORT

FINNED AREA

TUBE

ASME
 PARTS LIST
ITEM QTY PART NUMBER DESCRIPTION
1 1 C-FRAME-LEFT
2 1 C-FRAME-RIGHT
6 8 IPE100x3050
7 8 TK-3050
8 2 EA75x75x10 ASM
9 2 EA100x100x12 MIR
10 2 HDR_KEEPER
11 2 HDR_KEEPER-1.iam
12 4 EA65x65x6 ASA
13 4 LUG
14 14 1 AIRSEAL-F-TOP
15 1 AIRSEAL-S-TOP
16 1 Airseal-bot-S
12 17 1 Airseal-bot-f
17 18 1 MID-SPRT
19 4 Brace
12

18

13

7
THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
12 INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
10 PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

15
19

6 8

16

11

ASME
 2460.0
2650.0

80.0
30.0
3050.0

2460.0
2650.0

6250.0 6250.0
150.0

10

124.0
121.0
118.0
115.0

136.0
133.0
130.0
127.0
808.5

1455.0 9590.0=1370*7 1455.0

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

ASME
 74.8

749.1
599.6
74.8
BENDING DETAIL OF C-FRAME-01/2
50.0

STATIONARY HDR SIDE

80.0
610.0

12500.0

C-FRAME-01

STATIONARY HDR SIDE

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
50.0

WITHOUT EXPRESS WRITTEN PERMISSION.

80.0
610.0

12500.0

C-FRAME-02

ASME
 806.4 806.4
50.8

24.6
4.0
12.0 12.0

n18

f
92.0

f
FOR ONLY TWO SUPPORTS FOR ONLY TWO SUPPORTS

50.8
92.0

3038.0

100.0
12.0 12.0

Ø18.0
60.0

4 nND50

150.0

3038.0

79.0
12.0

12.0
47.0

79.0
65.0 65.0
Ø18.0
65.0
60.0

f f
12.0 12.0
150.0

3038.0
76.2

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
n18 PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

1086.6
.2
76

38

76.2
.1

135.0°
76
.2

1023.5

ASME
 THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD AND IS
INTENDED FOR DISTRIBUTION ONLY TO PERSON OR ORGANIZATION HAVING A LEGITIMATE NEED FOR THE
DRAWING. WHEN DISTRIBUTED OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD, THIS DRAWING IS
SUPPLIED FOR INFORMATION, IDENTIFICATION OR SERVICES TO ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
OR ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD. THIS
DRAWING IS PROTECTED UNDER THE COPYRIGHT LAW AS AN UNPUBLISHED WORK, AND MAY NOT BE
PUBLISHED OR COPIED OR REPRODUCED BY PERSONS OUTSIDE ABAHSAIN SPECIALIZED INDUSTRIAL CO. LTD
WITHOUT EXPRESS WRITTEN PERMISSION.

A
S
M
E

ASME