C13 Diesel Engine 440-711 hp @ 2100 rpm

1480-1990 lb-ft @
with ACERT Technology ™
1400 rpm Peak Torque

CAT® ENGINE SPECIFICATIONS

In-line 6-Cylinder, 4-Stroke-Cycle Diesel
Bore...........................................................................5.12 in (130 mm)
Stroke........................................................................6.18 in (157 mm)
Displacement..............................................................763 in3 (12.5 L)
Aspiration............................................. Turbocharged Aftercooled
Compression Ratio....................................................................18.0:1
Rotation (from flywheel end)............................ Counterclockwise
Cooling System1........................................................3.04 gal (11.5 L)
Lube Oil System (refill)............................................10.57 gal (40 L)2
Weight, Net Dry (approximate)
with standard equipment............................2610 lbs (1184 kg)
2371 lbs (1075 kg) Single Turbo
Shown 1
Engine only. Capacity will vary with radiator size and use of cab heater.
with optional 2
Optional 9 gal (34 L) oil pan also available in some OEM chassis.
equipment

STANDARD EQUIPMENT ACCESSORY EQUIPMENT

Cooling: gear-driven water pump, oil cooler Air compressors – gear driven 15.7 cfm or 31cfm
Crankcase breather Air inlet elbows
Electronic Control Module (ECM) Air inlet shut off
Electronic Data Link, SAE/ATA, SAE/J1939 Alternator (12 Volt-115 Amp)
Electronically Controlled Unit Injection Fuel System Automatic transmission adapter
Fuel – spin-on secondary filter, transfer pump Cat® Compression Brake, 12V or 24V
Gear-driven water pump Dry charge coolant conditioner
Governor – full-range electronically controlled Exhaust couplings
Hydraulic steering pump drive, SAE A Fan drive mounting bracket
Lifting eyes Flywheel
Lubrication: gear-driven pump, front or rear sump pan, Front engine support
full flow spin-on filter, oil filler, oil level gauge (dipstick) Front PTO adapter
Pad mount air conditioner compressor Fuel priming pump
Pad mount alternator Lubricating oil filter, bypass spin on
SAE No. 1 flywheel housing Optional secondary auxiliary oil filter
Series or Single Turbochargers Optional turbocharger mounting locations
Vibration damper Rear PTO (RPTO)
Starting motor: 12V or 24V
DIMENSIONS Turbocharger compressor outlet elbow

47 in 44 in
(1194 mm) (1118 mm)
RATING DEFINITIONS AND CONDITIONS
Performance is based on SAE J1995 standard conditions of
47 in 29.61 in. Hg (100 kPa) and 77° F (25° C).
(1194 mm)

Final dimensions will depend on completed specification.

C13 Diesel Engine
with ACERT Technology ™

ELECTRONIC FEATURES
Real time clock with date and time stamping of critical events - Engine Monitoring System – warning, derate, or shutdown
Electronic self-diagnostics - Enhanced theft deterrent and secure idle
(Cat Messenger or Pocket Tec required)
Electronically tabulated total fuel consumption, hours, idle time, - Fleet Information Software capability
and miles - Idle shutdown timer & override
Battery backup - Maintenance monitor [miles (km) or hours]
Quick stop recorder - OEM parameter lockout
- Progressive shifting and gear down protection
Compatible with Caterpillar Electronic Technician (ET)
- Vehicle speed [mph (km/h)] limiting and protection
Cold weather startup strategy and electronic idle control
Programmable Power Take-Off (PTO) functions:
functions
- Adjustable maximum engine rpm speed
ECM storage of operational, maintenance, diagnostic codes and - Adjustable minimum engine rpm speed
diagnostic data - Adjustable ramp rate up or down between PTO set speed(s)
J1939 compatible - Adjustable rpm “bump” intervals
Customer selectable, re-programmable operational parameters: - Adjustable speed control [mph (km/h)] of vehicle while in
- Adjustable low idle rpm PTO mode
- Automated Transmission compatibility - Limit engine torque to driven equipment
- Cooling fan control - Multi-speed PTO set speed capability
- Cruise control with exclusive Soft Cruise - Kick-out vehicle speed limit
- Customer password protection - Selectable PTO configuration for “in cab” or station
of remote operation

FEATURES
Worldwide Supplier Capability Full Range of Attachments
Caterpillar Wide range of bolt-on system expansion attachments, factory
- Casts engine blocks and heads designed and tested.
- Machines critical components Unmatched Product Support Offered Through
- Assembles complete engine Worldwide Caterpillar Dealer Network
Ownership of these manufacturing processes enables More than 1,800 dealer outlets.
Caterpillar to produce high quality, dependable product.
Caterpillar factory-trained dealer technicians service every
Factory-designed systems built at Caterpillar ISO 9001:2000 aspect of your industrial engine.
certified facilities.
99.7% of parts orders filled within 24 hours worldwide.
Testing
Caterpillar parts and labor warranty.
Prototype testing on every model:
- proves computer design Preventive maintenance agreements available for repair before
- verifies system torsional stability failure options.
- tests functionality on every model Scheduled Oil Sampling program matches your oil sample
Every Cat® engine is dynamometer tested under full load to against Caterpillar set standards to determine:
ensure proper engine performance. - internal engine component condition
- presence of unwanted fluids
- presence of combustion by-products

For more information visit: www.catdfp.com (North America)

For all other areas email: [email protected]

Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication.

© 2013 Caterpillar • All Rights Reserved • Printed in USA

CAT, CATERPILLAR, their respective logos, ACERT, “Caterpillar Yellow” and the “Power Edge” trade dress, as well as
corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.