DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-

R EasyRET 6-Port Antenna with Integrated 3 RCUs - 1.4m

Model: ATR4518R14v06

Antenna Specifications

Electrical Properties
3 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690

High Band
2-8 Ports
Polarization +45π , -45π
Electrical downtilt (π) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.6 18.0 18.4 18.6
Gain (dBi)
over all Tilts 17.4 ρ0.4 17.8 ρ0.4 18.1 ρ0.4 18.3 ρ0.5
Side lobe suppression for first
> 19 > 22 > 20 > 19
side lobe above main beam (dB)
Horizontal 3dB beam width (π) 66 ρ5.5 65 ρ4.2 64 ρ3.8 60 ρ3.2
Vertical 3dB beam width (π) 6.7 ρ0.5 6.1 ρ0.3 5.4 ρ0.4 5.0 ρ0.2
VSWR < 1.5
Cross polar isolation (dB) • 30
Interband isolation (dB) • 30
Front to back ratio, ρ30π (dB) > 27 > 27 > 29 > 29
Cross polar ratio (dB) 0π > 26 > 25 > 23 > 23
Max. power per input (W) 250 (at 50ć ambient temperature)
Intermodulation IM3 (dBc) ” -153 (2 x 43 dBm carrier)
Impedance (ȍ) 50
Grounding DC Ground

1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).

2. Electrical datasheet in XML format is available.

106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99
Packing dimensions (H x W x D) (mm) 1680 x 440 x 170
Antenna weight (kg) 17.3
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 27.0 (included clamps)
1262

Mast diameter supported (mm) 50 - 115

Radome material Fiberglass
1365

Radome colour Light grey

Operational temperature (ć) -40 .. +65
Frontal: 735 (at 150 km/h)
Wind load (N) Lateral: 70 (at 150 km/h)
Rear side: 690 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 4.3-10 Female
Connector position Bottom

Accessories
Item Model Description Weight Units per antenna

Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 16 e 2.1 kg 1 (Separate packing)

61
 DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-R
EasyRET 6-Port Antenna with Integrated 3 RCUs - 1.4m
Model: ATR4518R14v06

Integrated RET Specifications

Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)

* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET
antenna software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details
about protocol switching function, contact Huawei before system installation.

Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM

Integrated RET S/N:

HWMxxx..….yL
HWMxxx…..yyC
yL yyC yyyR
HWMxxx….yyyR

y – Yellow L - Left array

R - Right array C - Center array

Pattern sample for reference

1710 - 2690 MHz 1710 - 2690 MHz 1710 - 2690 MHz

(Left) (Center) (Right)

62