0% found this document useful (0 votes)
149 views5 pages

Supra 1994 - 1998 S7Plus

The document provides installation instructions for a Syvecs engine control module kit for a 1994-1998 Toyota Supra. The kit includes a Syvecs S7Plus or S7-i ECU and wiring loom. Installation involves removing the vehicle's battery, original ECU, and engine covers before proceeding to the Syvecs manual. The document also includes pinout diagrams and answers to frequently asked questions about features supported.

Uploaded by

Rajib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
149 views5 pages

Supra 1994 - 1998 S7Plus

The document provides installation instructions for a Syvecs engine control module kit for a 1994-1998 Toyota Supra. The kit includes a Syvecs S7Plus or S7-i ECU and wiring loom. Installation involves removing the vehicle's battery, original ECU, and engine covers before proceeding to the Syvecs manual. The document also includes pinout diagrams and answers to frequently asked questions about features supported.

Uploaded by

Rajib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Syvecs LTD

V1.2

Toyota Supra 94-98

This document is intended for use by a technical audience and describes a number of procedures that are potentially
hazardous. Installations should be carried out by competent persons only.

Syvecs and the author accept no liability for any damage caused by the incorrect installation or configuration of the
equipment.

Please Note that due to frequent firmware changes certain windows might not be the same as the manual illustrates.
If so please contact the Syvecs Tech Team for Assistance.

[email protected]
Contents
The kit should come with the following: 

1 x Syvecs S7Plus ECU or S7-i

1 x Supra PNP Wiring Loom 

Installation 

1.) Remove the Negative Terminal from the battery on the Vehicle 

2.) Remove the OEM Engine control modules found in the passenger footwell  

3.) Replace the battery terminal and engine covers and proceed to the Syvecs Manual 
Supra MK4 FAQ and Help 

Q) Does the Kit work with Auto Trans 

A) The Plus Kit offers full auto Gearbox control, via Scal 

Q) Can I install different in tank pump? 

A) Yes, the Syvec’s communicates with the OEM Fuel Pump Ecu to allow PWM Control of the Pump so it can be adjusted to suit your new pump. 

Q) What of the original features will now now work? 

A) None, even cruise control works

Q) Can you control the OEM TT Setup 

A) Yes but not if on a Auto Cars as not enough outputs present 

Q) Can I wire in a aftermarket Boost solenoid 

A) Yes this is done on the Blue connector next to the OEM TT Setup, It has 12v and Link directs to pin A5 on S6Plus or 

Email [email protected] for a base map to suit your setup. 

Pinouts of S7Plus Kit 

A DESCRIPTION
PART NUMBER
NOTES:
Syvecs Description  Syvecs Pinout  Car Pinout  Car Note 
PWR CTR OUT  A1
H‐Bridge1 / SlaveOut1 A2 10B  S1 Auto Solenoid 
H‐Bridge2 / SlaveOut2 A3 9B  S2 Auto Solenoid 
H‐Bridge3 / SlaveOut3 A4 23A  A/C Clutch 
H‐Bridge4 / SlaveOut4 A5 60B  Boost Solenoid 
H‐Bridge5 / SlaveOut5 A6 33B  Idle 1 
H‐Bridge6 / SlaveOut6 A7 35B  Idle 2 
H‐Bridge7 / SlaveOut7 A8 34B  Idle 3 
H‐Bridge8 / SlaveOut8 A9 32B  Idle 4 
FUEL1 A10 20B  Injector1 
FUEL2 A11 19B  Injector2 
FUEL3 A12 18B  Injector3 
FUEL4 A13 17B  Injector4 
FUEL5 A14 16B  Injector5 
FUEL6 A15 15B  Injector6 
FUEL7 A16 Secondary Injector 1 
FUEL8 A17 Secondary Injector 2 
PWM1 /*FUEL9 A18 16A  Tacho ‐ Needs 12v Pullup 
PWM2 / *FUEL10 A19 Secondary Injector 3 
PWM3 / *FUEL11 A20 Secondary Injector 4 
PWM4 / *FUEL12 A21 22A  Fuel Pump ‐ Needs 5v 
Pullup 
PWM5  A22 Secondary Injector 5 
PWM6  A23 Secondary Injector 6 
PWM7  A24 13B  SLN ‐ Needs Flyback 
PWM8  A25 12B  SLT ‐ Needs Flyback 
IGN1  A26 57B  Ignition 1 
IGN2   A27 56B  Ignition 2 
IGN3   A28 55B  Ignition 3 
IGN4   A29 54B  Ignition 4 
IGN5   A30 53B  Ignition 5 
IGN6   A31 52B  Ignition 6 
PWRGND  A32 69B 
PWRGND  A33 79B 
PWRGND  A34

B DESCRIPTION
PART NUMBER
NOTES:

PWRGND  B1 80B 
CAN2L  B2
CAN2H  B3
KNOCK  B4 External Knock 
Loom 
KNOCK 2  B5 External Knock 
Loom 
PVBAT  B6
IVBAT  B7 31A  12v 
LAM1A  B8 Nernst Cell 
LAM1B  B9 Ion Pump 
LAM1C  B10 Cal Trim Resistor 
LAM1D  B11 Virtual Ground 
LAM1HEATER  B12
IVBAT  B13
LAM2A  B14 Nernst Cell 
LAM2B  B15 Ion Pump 
LAM2C  B16 Cal Trim Resistor 
LAM2D  B17 Virtual Ground 
LAM2HEATER  B18
IVBAT  B19 31B  Auto Solenoids 12v 
KLINE B20
RS232RX B21
RS232TX B22
LANRX‐  B23
LANRX+  B24
LANTX‐  B25
LANTX+  B26

C DESCRIPTION
PART NUMBER
NOTES:

KNOCKGND C1 External Loom


ANGND C2 1B, 3B, 7B, 65B
ANGND C3
ANGND C4
5V OUT C5 41B
5V OUT C6
5V OUT C7
CAN L C8
CAN H C9
AN01 C10 26B G1
AN02 C11 27B NE
AN03 C12 External FL ABS
AN04 C13 External RL ABS
AN05 C14 34A A/C Switch
AN06 C15 21B Overdrive Clutch Speed
AN07 C16 2A Gearbox Speed
AN08 C17
AN09 C18 43B VTA
AN10 C19 62B Map Input
AN11 C20 External Oil Pressure Signal
AN12 C21 External Fuel Pressure Signal
AN13 C22 44B Coolent Temp
AN14 C23 45B Air temp
AN15 C24 External Cal Swithc
AN16 C25 External Traction Swithc
EGT1- C26
EGT1+ C27
PWR CTR IN C28
AN S1 / Slave An01 C29 7A R Switch
AN S2 / Slave An02 C30 External Up Switch
AN S3 / Slave An03 C31 External Down Switch
AN S4 / Slave An04 C32 28A Overdrive Sw
AN S5 / Slave An05 C33 24B Auto Trans Temp
AN S6 / Slave An06 C34 76B Park/Neutral Pos

You might also like