Scribd
Upload
58 views

LLF Series: Low-Low Frequency Elastomer Vibration Isolation Mounts

This document summarizes a series of low-frequency elastomer vibration isolation mounts called the LLF Series. The mounts are available in models that can support axial loads between 250-1300 pounds and all have a maximum deflection of 0.15 inches at full load. They feature a fail-safe design, low natural frequency of around 8 Hz, and attenuate structureborne noise. The mounts use corrosion resistant steel and sintered metal with a neoprene elastomer that operates from -20 to 180 degrees Fahrenheit. They are used to isolate engines, equipment, and machinery from vibration.

Uploaded by

Carlos Torres Oliveros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
58 views

LLF Series: Low-Low Frequency Elastomer Vibration Isolation Mounts

This document summarizes a series of low-frequency elastomer vibration isolation mounts called the LLF Series. The mounts are available in models that can support axial loads between 250-1300 pounds and all have a maximum deflection of 0.15 inches at full load. They feature a fail-safe design, low natural frequency of around 8 Hz, and attenuate structureborne noise. The mounts use corrosion resistant steel and sintered metal with a neoprene elastomer that operates from -20 to 180 degrees Fahrenheit. They are used to isolate engines, equipment, and machinery from vibration.

Uploaded by

Carlos Torres Oliveros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Low-Low Frequency Elastomer

LLF Series Vibration Isolation Mounts


Part Axial Load Range Deflection at
Number (lbs.) Max Load (in.)
LLF-400 250-400 .15
LLF-700 400-700 .15
LLF-1000 700-1000 .15
LLF-1300 1000-1300 .15

Features/Benefits
■ Static Load Range 250 –1300 lbs.
■ Low Profile
■ Rugged Construction
■ All bonded construction 7.50
6.00
■ Fail-safe design with built-in snubbing washer
■ Axial to radial stiffness – approximately 1:3.5
■ Low natural frequency (approx. 8 Hz at max. load)
4.75
■ Structureborne noise attenuation

Construction/Material Data
■ Structural sections – carbon steel/sintered metal
DIA. .656 Hole (2 Places)
■ Corrosion resistant coating on metal surfaces
3/4 – 10 TAP
■ Neoprene elastomer DIA. 1.50 MAX. TH'D DEPTH

• Resists oils, ozone and most solvents DIA. 4.00


DIA.
1.75 1.00
• Operating temperature range (–20°F to +180°F) .25

• Damping ratio C/Cc = 0.1 (transmissibility


approx. 5:1 at resonance) 3.62
■ Weight - 6 lbs. (approx.) 4

Applications DIA. 3.50


DIA. 3.75
■ Highway and off-highway vehicles RECOMMENDED DETAIL 'A'
CLEARANCE
• Isolate engines, cabs and radiators
■ Motor generators and compressors
■ Pumps and centrifuges
Axial Load vs. Deflection
■ Portable equipment and machinery 4000
■ Marine equipment and power plants
■ Fans and blowers 3500

3000
-1300
Load – Pounds

2500
Note: Mount is provided with snubbing washer -1000
attached as shown in Detail 'A' 2000

-700
1500

1000
-400

500

0
0 .05 .10 .15 .20 .25 .30 .35 .40
Deflection – Inches

11 KORFUND DYNAMICS

You might also like