Section : Body Electrical

Ref. No. : BE-5017

Service Bulletin Date :

Page :
Jun.,2005
1 of 30

Area Application : Europe

Model Name : ALL MODELS
Model Code : ALL

Subject : Engine Immobiliser System Overview

As an error was found in service bulletin BE-4014 (issuse Jul. 2004), this service bulletin is being
reissued. Page 4 and 5 have been edited and page 17 and 26 have been added.
This service bulletin gives a detailed overview of different types of Engine Immobiliser systems used on
European specification TOYOTA vehicles produced after August, 1998. For a detailed list of vehicle
model codes, see pages 4 and 5.
This bulletin gives TOYOTA technicians to register / erase transponder key codes in the Immobiliser
system in a more effective way, and provides practical information about what to do in case of lost key(s),
malfunction component replacement, etc.
CONTENT:
1. IMMOBILISER SYSTEM.............................................................................................................2 page
2. TRANSPONDER KEY CODE REGISTRATION FUNCTIONS....................................................3 page
3. KEY CODE REGISTRATION TABLE..........................................................................................4 page
4. KEY CODE AUTOMATIC REGISTRATION MODE....................................................................5 page
5. REGISTRATION OF ADDITIONAL KEY CODES.......................................................................6 page
6. KEY CODE ERASURE...............................................................................................................7 page
7. ECU COMMUNICATION ID REGISTRAION..............................................................................8 page
8. TIPS AND TRICKS (what to do in case of lost keys)..................................................................9 page
Part No. Information :
New Part No. New Part Name Qty
NA NA NA

Production Effective :
VIN Production Date
NA Augst, 1998

ENGINE IMMOBILISER SYSTEM

REGISTRATION
1. IMMOBILISER SYSTEM
Immobiliser systems fitted into TOYOTA vehicles produced after August, 1998 (except Corolla WZE
110) can be divided into 2 different types.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 2 of 30

Integrated Type Immobiliser System

Transponder Key Amplifier

ECM
CODE RXCK TXCT
TXCT RXCK CODE

B123668E02

For an integrated type immobiliser system, the transponder key ECU is integrated into the ECM.
Direct communication exists between the key coil amplifier and ECM.
Separate Type Immobiliser System

Transponder Key Amplifier

GND TXCT CODE VS5

AGND TXCT CODE VS5

Transponder Key ECU
EFII EFIO

IMO IMI
ECM
B123641E02

For a separate type immobiliser system, a separate transponder key ECU (often called an
immobiliser ECU)* is between the key coil amplifier and ECM. The ECM receives permission or
prohibition signals through the EFII and EFIO terminal.
For details about different models, please refer to the table described in "KEY CODE
REGISTRATION TABLE" on page 4.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 3 of 30

2. TRANSPONDER KEY CODE REGISTRATION FUNCTIONS

(a) The transponder key code registration function consists of an initial (automatic) registration,
and ditinal registration, and deletion.
(1) Initial registration of key code
This is a system to automatically register a new transponder key code (master key code
and sub-key code) when the ECU is replaced.
After the ECU is replaced, turning the ignition switch ON makes the security indicator light
blink. In this condition, inserting the master key and sub-key in the ignition key cylinder
automatically registers the transponder key code in the ECU.
HINT:
In the initial (automatic) registration mode, the transponder key code can be registered for
up to 3 or 4 keys. The last registration (the third or fourth key) is performed at the sub-key
registration mode.
(b) After the initial registration, on some models it may take approximately 30 minutes to match the
communication ID between the transponder key ECU and the ECM.
(1) Registration of additional key code
This is a function to perform the additional registration of a new transponder key code
(master key code and sub-key code) with the transponder key code registered in the ECU.
HINT:
Additional registration can also be performed using a intelligent tester.
The number of transponder key codes that can be registered in the immobiliser system
varies depending on the system type.
(2) Erasure of key code
This is a function to erase all transponder key codes except for the master key code that is
used to complete the erasure. Without the master key, the erasure is impossible.
(3) The difference between master key and sub-key
2 or 3 master keys and sub-key are set in the ignition keys for the engine immobiliser
system.
Registration and erasure of the key can be performed only by the master key. Therefore,
to register the sub-key, the master key is necessary. The setting of the master key and
sub-key is also classified according to the registration methods.
NOTICE:
In the initial registration
3. KEY CODE REGISTRATION TABLE

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 4 of 30

B123642

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 5 of 30

B123643

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 6 of 30

4. KEY CODE AUTOMATIC REGISTRATION TABLE

(a) Registration of new transponder key into a blank ECU

A-1

START Security indicator blinks until first key

is inserted. Indicator lights up after
key registration.

Insert key in ignition key cylinder.

Security indicator is ON

Key code is being registered.

(Registration is completed in about 1 second after key is inserted.)

Security indicator is OFF

Registration has completed.

Remove key.
Security indicator is ON. (After last
key has been registered, indicator
remains OFF until yo remove key.
After key removal, indicator starts
blinking.)
YES
Will you register next key?

NO

END
B123644E02

HINT:
• This is a system to automatically register a new transponder key code (master key code and
sub-key code) when the ECU (in case of integrated type immobiliser system, ECM and
incase of separated type immobiliser system, transponder key ECU) is replaced.
• In the automatic registration mode, the transponder key code can be registered for up to 3
keys. The last registration (the third or fourth key) is performed in the sub-key registration
mode.
• After the automatic registration, on some models it may take approximately 30 minutes to
match the communication ID between the transponder key ECU and the ECM.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 7 of 30

• If the key code registration has failed in automatic key code registration mode, code 2-1 will
be output from the security indicator. Trying to re-register an already registered key will
cause code 2-2 to be output when the key is inserted. If the number of registered key codes
exceeds the limit, code 2-3* will be output from the security indicator. The output details are
shown below.

Security Indicator
0.2 sec.
Normal
(Immobiliser ON
system is
operating OFF
normally)
1.8 sec.
0.25 sec. 0.5 sec.

ON
Code 2-1
OFF

0.25 sec. 1 sec.

0.25 sec. 0.5 sec.

ON
Code 2-2
OFF

0.25 sec. 1 sec.

0.25 sec. 0.5 sec.

ON
Code 2-3*
OFF

0.25 sec. 1 sec.

B123645E02

HINT:
*: This code is not available on some vehicles.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 8 of 30

A-2
Initial condition: All doors closed, not key in cylinder.

START

Insert master key in ignition key cylinder.

Ignition switch: LOCK ON

Within 10
seconds
Remove master key.
Within 10
seconds
YES

Will you register next master key?

NO

Continued on next page

B123646E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 9 of 30

Continued from the previous page

NO

Driver side door: Open Close

Within 10 seconds

NO
Will you register sub-key?

YES

Insert sub-key to be registered in ignition key cylinder.

Within 10 seconds

Ignition switch: LOCK ON

Remove sub-key.

END

B124234E01

*1: When not registering sub-key, register the master key within 10 seconds of opening and
closing driver side door.
(b) Forced completion of automatic registration mode
HINT:
This can only be done after at least 2 key codes have been registered in automatic registration.
(1) Without pulling the key out, use the intelligent tester to request automatic registration
mode.
(2) When the intelligent tester II is not a vailable use an already registered master key to turn
the ignition switch from ON to OFF 5 times within 10 second.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 10 of 30

5. REGISTRATION OF ADDITIONAL KEY CODES

(a) Registration of additional master key

M-1
Insert already registered master key in ignition key
cylinder and turn ignition switch ON.

Using intelligent tester, select master key registration.

Within 20 seconds
Remove master key.

Within 10 seconds
Insert key to be registered in ignition key cylinder.

Remove key (additional master key) from ignition More than 70 seconds
key cylinder.

Registration mode ends when the key is pulled out and

one of the following occurs: 1) the brake pedal is
depressed one or more times within 10 seconds, or 2)
10 seconds have passed.

B123647E01

HINT:
Please follow the screen of the intelligent tester for a more detailed procedure.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 11 of 30

M-2
Insert already registered master key in ignition key
cylinder and turn ignition switch ON.

Using intelligent tester, select master key registration.

Within 20 seconds
Remove master key.

Insert key to be registered in ignition key cylinder. Within 10 seconds

(Security indicator blinks.)

After 60 seconds, additional master key is registered.

(Security indicator OFF)

Registration mode ends when the key is pulled out and

one of the following occurs: 1) the brake pedal is
depressed one or more times within 10 seconds, or 2)
10 seconds have passed.

B123648E01

HINT:
Please follow the screen of the intelligent tester for a more detailed procedure.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 12 of 30

M-3 START

Insert already registered master key into ignition key cylinder.

Within 15 seconds
Repeatedly turn ignition switch from OFF to ON 5 times. *1

Repeat driver side door open / close operation 6 times. *2

Within 20 seconds

Remove master key *3

Within 10 seconds

Insert key to be registered into ignition key cylinder. *4 Within 10 seconds

Keep ignition switch ON for 60 seconds or more. *5

More than 60 seconds

Within 10
seconds Remove key from ignition key cylinder.

YES Will you register driver side door.

*6

NO

Open and close driver side door.

END
B123649E01

HINT:
*1:
Turn the ignition switch from OFF to ON 5 times within 15 seconds of inserting the master key
in the ignition key cylinder. The ignition switch's final position must be ON, or the registration
will not be carried out. Then go to the next operation.
*2:

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 13 of 30

Open and close the driver side door within 15 seconds of inserting the master key in the ignition
key cylinder. Then open and close the driver side door another 5 times within 20 seconds of
closing the driver side door.
*3:
Remove the master key from the ignition switch within 20 seconds of closing the driver side
door.
*4:
Insert the key to be registered in the ignition key cylinder within 10 seconds of removing the
master key.
*5:
Turn the ignition switch from OFF to ON within 10 seconds of removing the previous key.
*6:
If you are to register another key, insert the next key within 10 seconds of removing the
pervious key.
*7:
• When any operation time limit in the flowchart on the pervious page elapses, registration
mode ends.
• When the next procedure is performed while the timer is running, the current timer stops and
the next timer starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 14 of 30

(b) Registration of additional master / sub-key

MS-1
Security Indicator

BLINKING START
(Until first key
is inserted)

Insert already registered master key into ignition key

cylinder and turn ignition switch ON.

OFF
Intelligent tester operation:

1. Select model name or code from menu.

2. Select IMMOBILISER.
3. Select ID UTILITY. Within 120 seconds
4. Select TRANSP CODE REG.
After above operation, proceed to next step in
accordance with tester screen’s instructions.

ON Within 20 seconds
after tester instruction
Remove master key.

Within 10 seconds
Insert key to be registered into ignition key cylinder.

BLINKING After 60 seconds, key is registered.

(Security indicator OFF)

OFF

END
B123650E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 15 of 30

MS-2
Additional Registration

Security Indicator

BLINKING START
(Until first key
is inserted)
Insert already registered master key into key slot and
turn power switch ON (IG).

OFF
Intelligent tester II operation:

1. Select Body.
2. Select Immobiliser.
3. Select Utility
4. Select Transponder Code Registration.
After above operation, proceed to next step in
accordance with tester screen’s instructions. Within 120 seconds

Within 20 seconds
ON
after tester instruction
Turn power switch OFF and remove master key.

Within 10 seconds
Insert key to be registered in key slot.

BLINKING
After 60 seconds, key is registered.
(Security indicator OFF)

OFF

END
B123661E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 16 of 30

MS-3
START

Insert already registered master key into ignition key cylinder.

Within 15 seconds
Repeatedly turn ignition switch from OFF to ON 5 times. *1

Repeat driver side door open / close operation 6 times. *2

Within 20 seconds

Remove master key. *3

Within 10 seconds

Insert key to be registered into ignition key cylinder. *4

Within 10 seconds

Keep ignition switch ON for 60 seconds or more. *5 More than 60

Within 10 seconds
seconds
Remove key from ignition key cylinder.

YES
Will you register next key?
*6

NO

Open and close driver side door.

END

B123654E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 17 of 30

MS-5 Additional Registration:

BLINKING Security Indicator START

(until the first key
is inserted)
Make sure that the vehicle fulfills the following conditions:
Driver side door is closed.
No key is in the ignition key cylinder.

5 sec. or more
Wait for 5 seconds or more.

OFF Insert the already registered master key into the ignition key
cylinder, and make sure that the security indicator turns OFF.

Pull out and insert the master key 4 times*.

Open / close the driver side door 6 times. Within 35 sec.

ON
Remove the master key.

Within 10 sec.
Insert the key to be registered into the ignition key cylinder.

BLINKING
After 60 seconds, the key is registered.
(The security indicator turns OFF.)

OFF

END

*: Registration operation will be cancelled if the key is not reinserted within 3 seconds.
B124463E01

HINT:
*1:
Turn the ignition switch from OFF to ON 5 times within 15 seconds of inserting the master key
in the ignition key cylinder. The ignition switch's final position must be ON, or the registration
will not be carried out. Then go to next operation.
*2:

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 18 of 30

Open and close the driver side door within 15 seconds of inserting the master key in the ignition
key cylinder. Then open and close the driver side door another 5 times within 20 seconds of
closing the driver side door.
*3:
Remove the master key from the ignition switch within 20 seconds of closing the driver side
door.
*4:
Insert the key to be registered in the ignition key cylinder within 10 seconds of removing the
master key.
*5:
Turn the ignition switch from OFF to ON within 10 seconds of inserting the key.
*6:
If you are to register another key, insert the next key within 10 seconds of removing the
previous key.
*7:
• When any operation from limit in the flowchart on the previous page elapses, registration
mode ends.
• When the next procedure is performed while the timer is running, the current timer stops and
the next timer starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 19 of 30

(c) Registration of additional sub-key.

S-1

Insert already registered master key in ignition key cylinder and

tun ignition switch ON.

Using intelligent tester, select sub-key registration.

Within 20 seconds
Remove master key.

Within 10 seconds
Insert key to be registered inn ignition key cylinder.

More than 70 seconds

Remove key (additional sub-key) from ignition key cylinder.

Registration mode ends when the key is pulled out and one of the
following occurs: 1) the brake pedal is depressed one or more
times within 10 seconds, or 2) 10 seconds have passed.

B123652E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 20 of 30

S-2
Insert already registered master key in ignition key cylinder and turn
ignition switch ON.

Using intelligent tester, select sub-key registration.

Within 20 seconds

Remove master key.

Within 10 seconds
Insert key to be registered in ignition key cylinder.
(Security indicator blinks)

After 60 seconds, additional sub-key is registered.

(Security indicator OFF)

Registration mode ends when the key is pulled out and one of the follow-
ing occurs: 1) the brake pedal is depressed one or more times within 10
seconds, or 2) 10 seconds have passed.

B123653E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 21 of 30

S-3
START

Insert already registered master key into ignition key cylinder.

Within 15 seconds

Repeatedly turn ignition switch from OFF to ON 4 times. *1

Repeat driver side door open / close operation 5 times. *2

Within 20 seconds

Remove master key. *3

Within 10 seconds

Insert key to be registered into ignition key cylinder. *4

Within 10 seconds

Keep ignition switch ON for 60 seconds or more. *5 More than 60

Within 10 seconds
seconds

Remove key from ignition key cylinder.

YES
Will you register next key?
*6

NO

Open and close driver side door.

END

B123654E03

HINT:
Please follow the screen of the intelligent tester for a more detailed procedure.
HINT:
Please follow the screen of the intelligent tester for a more detailed procedure.
HINT:
*1:

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 22 of 30

Turn the ignition switch from OFF to ON 5 times within 15 seconds of inserting the master key
in the ignition key cylinder. The ignition switch's final position must be ON, or the registration
will not be carried out. Then go to next operation.
*2:
Open and close the driver side door within 15 seconds of inserting the master key in the ignition
key cylinder. Then open and close the driver side door another 5 times within 20 seconds of
closing the driver side door.
*3:
Remove the master key from the ignition switch within 20 seconds of closing the driver side
door.
*4:
Insert the key to be registered in the ignition key cylinder within 10 seconds of removing the
master key.
*5:
Turn the ignition switch from OFF to ON within 10 seconds of inserting the key.
*6:
If you are to register another key, insert the next key within 10 seconds of removing the
previous key.
*7:
• When any operation from limit in the flowchart on the previous page elapses, registration
mode ends.
• When the next procedure is performed while the timer is running, the current timer stops and
the next timer starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 23 of 30

6. KEY CODE ERASURE

E-1

Security Indicator

BLINKING START
(Until first key
is inserted.)

Insert already registered master key into ignition key

cylinder and turn ignition switch ON.

OFF

Intelligent tester operation:

1. Select model name or code from menu.

2. Select IMMOBILISER. Within 120 seconds
3. Select ID UTILITY.
4. Select TRANSP CODE ERS.
After above operation, proceed to next step in
accordance with tester screen’s instructions.

Within 10 seconds
after tester indicates
ON for 1 second
then OFF
Remove master key.

BLINKING

END

B123655E01

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 24 of 30

E-2
Initial condition: All doors closed, no key in cylinder.

START

Insert already registered master key into ignition key cylinder.

Within 15 seconds

Repeatedly turn ignitions switch from OFF to ON 6 times. *1

Repeat driver side door open / close operation 7 times. *2

Within 20 seconds

Remove master key. *3

END
B123656E01

HINT:
*1:
Turn the ignition switch from OFF to ON 5 times within 15 seconds of inserting the master key in the
ignition key cylinder. The ignition switch's final position must be ON, or the registration will not be
carried out. Then go to next operation.
*2:
Open and close the driver side door within 15 seconds of inserting the master key in the ignition key
cylinder. Then open and close the driver side door another 5 times within 20 seconds of closing the
driver side door.
*3:
Remove the master key from the ignition switch within 20 seconds of closing the driver side door.
• When any operation time limit in the flowchart on the previous page elapses, registration mode
ends.
• When the next procedure is performed while the timer is running, the current timer stops and the
next timer starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 25 of 30

E-3
Security Indicator

BLINKING START
(Until first key
is inserted.)
Insert already registered master key in key slot and
turn power switch is ON (IG).

OFF
Intelligent tester II operation:

1. Select Body.
2. Select Immobiliser.
3. Select Utility.
4. Select Transponder Code Erasure.
After above operation, proceed to next step in
accordance with tester screen’ s instructions. Within 120 seconds

ON for 1 second Within 10 seconds

then OFF after tester indicates
Turn power switch OFF and remove master key.

BLINKING

END
B123657E01

HINT:
• A brief outline of procedures for key code registration is shown on this page. For more detailed
information, please refer to the intelligent tester screen's instructions.
• When the immobiliser system is operating normally and the key is pulled out, the security
indicator blinks continuously.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 26 of 30

E-4
Security Indicator

START
BLINKING
(until the first
key is inserted)
Make sure that the vehicle fulfills the following conditions:
D Driver side door is closed.
D No key is in the ignition key cylinder.

5 sec. or more
Wait for 5 seconds or more.

OFF Insert the already registered master key into the ignition key
cylinder, and make sure that the security indicator turns OFF.

Within 35 sec.

Pull out and insert the master key 5 times alternately*.

Open / close the driver side door 7 times alternately.

ON for 1 sec. Within 10 sec.

then OFF
Remove the master key.

BLINKING
END

*: Erasure operation will be cancelled if the key is not reinserted within 3 seconds.
B124464E01

HINT:
When the immobiliser system operates normally and the key is pulled out, the security indicator
blinks continuously.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 27 of 30

7. ECU COMMUNICATION ID REGISTRATION (ID-1)

(a) Register the ECU communication ID.

CG

SST TC
DLC3
B123658E01

• Using SST, connect terminals TC and CG of the DLC3.

SST:
09843-18040
• Turn the power switch ON (IG) (do not start the engine) and leave it as is for 30 minutes.
• Turn the power switch OFF and disconnect terminals TC and CG.
• Check that the hybrid vehicle control system starts.
8. ECU COMMUNICATION ID REGISTRATION (ID-2)
(a) Register the ECU communication ID.

CG

SST TC
DLC3
B123658E01

• Using SST, connect terminals TC and CG of the DLC3.

SST:
09843-18040
• Turn the power switch ON (IG) (do not start the engine) and leave it as is for 30 minutes.
• Turn the power switch OFF and disconnect terminals TC and CG.
• Check that the hybrid vehicle control system starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 28 of 30

(b) ECU Communication ID Registration

Security Indicator

BLINKING START
(Until first key
is inserted.)
Insert already registered master key in key slot and turn
power switch ON (IG).

OFF
Intelligent tester II operation:

1. Select Body.
2. Select Immobiliser.
3. Select Utility.
4. Select ECU Communication ID Registration.
After above operation, proceed to next step in Within 120 seconds
accordance with tester screen’ s instructions.

ON for 1 second Within 10 seconds

then OFF after tester indicates
Turn power switch OFF and remove master key.

BLINKING

END
B123659E01

HINT:
• A brief outline of procedures for key code registration is shown on this page. For more
detailed information, please refer to the intelligent tester screen's instructions.
• When the immobiliser system is operating normally and the key is pulled out, the security
indicator blinks continuously.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 29 of 30

(c) ECU Communication ID Registration

START

Insert already registered master key in key slot and turn power switch
ON (READY) with brake pedal depressed.

Check that hybrid control system remains on for more than 3 seconds.

END

B123660E01

9. ECU COMMUNICATION ID REGISTRATION (ID-3)

(a) Register the ECU communication ID.

CG

SST TC
DLC3
B123658E01

• Using SST, connect terminals TC and CG of the DLC3.

SST:
09843-18040
• Turn the power switch ON (IG) (do not start the engine) and leave it as is for 30 minutes.
• Turn the power switch OFF and disconnect terminals TC and CG.
• Check that the hybrid vehicle control system starts.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.
 Ref. No. : BE-5017

Service Bulletin Page : 30 of 30

(b) ECU Communication ID Registration

START

Insert already registered master key in key slot and turn power switch
ON (READY) with brake pedal depressed.

Check that hybrid control system remains on for more than 3 seconds.

END

B123660E01

10. TIPS AND TRICKS (what to do in case of lost keys)

HINT:
• When unsure if the remaining keys are master keys or sub-keys, insert each key into the ignition
switch and use the Data List to check the key registration type.
• For further details, refer to the applicable repair manual.
• If all master keys are lost, proceed to step (c).
(a) When one key is lost.
(1) Using the master key, erase all the key codes from the ECU.
(2) Using the procedures described in "REGISTRATION OF ADDITIONAL KEY CODE" on
page 8, reregister all the remaining key codes.
(b) When two or more keys are lost.
(1) Using the master key, erase all the key codes from the ECU.
(2) Using the procedures described in "REGISTRATION OF ADDITIONAL KEY CODE" on
page 8, reregister all the remaining key codes.
(c) When all keys are lost.
(1) Replace ECM (integration type) or transponder key ECU (separate type).
(2) Using the procedures described in "KEY CODE AUTOMATIC REGISTRATION MODE" on
page 6, and / or "REGISTRATION OF ADDITIONAL KEY CODE" on page 8, reregister
new keys.

OVERSEAS CUSTOMER
SERVICE TECHNICAL DIV.