Scribd
Upload
51 views

Center of Pressure On Partially and Fully Submerged Plates: Experiment 1

1. The experiment determined the center of pressure on partially and fully submerged plates by measuring the balance and water level as weights were added then removed from a submerged plane surface. 2. Calculations using moments about the pivot point were used to find the height of the center of pressure above the bottom of the plate for each reading. 3. A straight line was fitted to the calculated center of pressure heights plotted against the water levels, and its slope was compared to the theoretical slope value.

Uploaded by

Luis Timbe
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
51 views

Center of Pressure On Partially and Fully Submerged Plates: Experiment 1

1. The experiment determined the center of pressure on partially and fully submerged plates by measuring the balance and water level as weights were added then removed from a submerged plane surface. 2. Calculations using moments about the pivot point were used to find the height of the center of pressure above the bottom of the plate for each reading. 3. A straight line was fitted to the calculated center of pressure heights plotted against the water levels, and its slope was compared to the theoretical slope value.

Uploaded by

Luis Timbe
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Experiment 1

Center of Pressure on Partially and Fully Submerged Plates

n Purpose: To determine the center of pressure on a partially submerged and fully


submerged plane surface.

Figure 1-1 Hydrostatic Pressure Apparatus

n Procedure:
1. Place the quadrant on the two dowel pins and, using clamping screw, fasten it to the
balance arm.
2. Level the Plexiglas tank by adjusting the screwed feet. The level is indicated on the
circular spirit level.
3. Hang the balance pan and make the balance arm horizontal by moving the counter
balance weight.
4. Measure a, L, d, b as shown in Figure 1-1.
5. Close the drain cock and fill the tank with water until the water level reaches the
bottom edge of the quadrant. Level the arm by moving the counterbalance weight.
6. Place 50 grams on the balance pan and slowly add water to the tank until the balance
arm is again horizontal. Record the water level (y) on the quadrant and the weight on
the balance pan (W = mg).
7. Repeat Step 6 for several increments placing about 50 grams on the balance pan for
each step until the water level reaches the top of the quadrant end face. Repeat Step 6
one more time so that the quadrant end face is totally submerged for this last run.
8. Remove each increment of weight and allow the water to drain until the balance arm
is level. Note the weights and water levels for each increment as the weights are
removed.
n Interpretation of Results:

You want to find the center of pressure on the plate for each reading taken during filling
and draining the tank. To do this, take moments about the pivot. Thus,
− mg ( L) + F (a + d − z ) = 0 (1-1)
in which z = the height of the center of pressure above the bottom of the plate. The force
on the submerged plate is given by,
1
F = ρgyA with y = y and A = by (1-2)
2
Therefore,
y2
F = ρgb (1-3)
2
Substituting,
 ρgy 2b 
− mg ( L) +  (a + d − z ) = 0 (1-4)
 2 
Solving for z we get,
2mL
z = a+d − 2 (1-5)
ρy b
Note that ρ = 1 gm/cm3 or 1000 kg/m3.

For each of the readings obtained during filling and draining the tank calculate the height
above the bottom of the plate of the center of pressure (z) and plot the calculated values of
z against y. Fit a straight line to the data.

n Questions:
1. What is the slope of the straight line?
2. How far above the bottom of the plate should the center of pressure be?
3. Theoretically, what should the value of the slope be? Did you get this value? If not,
why not?
4. If the plate had been a isosceles triangle with its base at the bottom, what would the
theoretical slope of the line be?

n Data:
Water temperature=
a= 10.2 cm; L=27.5 cm; d= 10.0 cm; b=7.5 cm
Tank Filling Tank Draining
m (gm) y (cm) m (gm) y (cm)

You might also like