Form number DOT TS 2-10

AMP Temporary Revision No. 1, date 2010 May 03

SAAB SF340A DAILY INSPECTION CHECKLIST

Daily Check

MRB REF. SCOPE OF WORK REF. SIGN

After the first flight through low density volcanic ash define
and select one reference area, approximately 4x4in
(100x100mm) at one of the following locations:

SAAB Service
- Newsletter
SN 340-1001

Make sure the painted surface of the reference area is not

damaged or previous affected by erosion, if required, re-
paint the area before inspection (Ref. SRM 51-20-43).
Check accumulated Flight Hours in low density volcanic ash
SAAB Service
with Technical Department; the aircraft must be inspected
- Newsletter
after 25FH, 75FH and 175FH of exposure for possible SN 340-1001
erosion impact.
0600-710-01E Nose landing gear and doors. General visual inspection (EZAP). JC:0600-710-01E
Zone: 710
291001 Check of differential pressure indicators. AMM:29-10-00-00
Zone: 113
292001 Inspection of leakage of hydraulic fluid (WAC). AMM:29-20-00-00
Zone: 113
Inspect front and side windshields for cracks, scratches and
AMM:56-00-00-01
5610-210-01E chipping also inspect windshield moisture seals.
AMM:56-10-00-01-1
Zone: N/A
Inspection of wiper arm assembly for cracks, corrosion, proper
304302 alignment and secure attachment. AMM:30-45-10-06
Zone: 210
Visually inspect angle of attack (AOA) vanes for condition and
273501 check for freedom of movement. JC:273501
Zone: 210
5610-210-03E Inspect cabin windows for cracks, scratches and chipping. AMM:56-20-05-06
Zone: N/A
Visual inspection of de-icer boots for general condition and
301001 security. AMM:30-10-35-06
Zone: 512, 612, 513, 613, 331, 341
Inspect fuel for contamination by sumping each wing fuel
281102 storage tank. AMM:12-10-28-03
Zone: 521, 561
0600-732-01I Main landing gear. General visual inspection (EZAP).
JC: 0600-732-01I
0600-742-01I Zone: 732, 742

Revision No. 1, 22-07-2010 Page - 1 of 2

Form number DOT TS 2-10
AMP Temporary Revision No. 1, date 2010 May 03

Visual check Dowty propeller de-icer boots and protective tape

306001 for general condition and security. DOWTY CMM
Zone: 410, 420
Visually inspect propeller assembly for evidence of oil or grease
JC:611001
611001 leakage from hub assy. SB:SF340-61-50
Zone: 410, 420
711001 Visual inspection of powerplant for general condition. JC:711001
Zone: 451, 453, 454, 461, 463, 464 G.E. MM
Inspect engine air intakes erosion coat for chips, scratches and
716001 general condition. G.E. MM
Zone: 452, 462
726101 Check common drain for excessive oil. G.E. MM
Zone: 430, 440
731001 Visual inspection of overboard drain for evidence of fuel. G.E. MM
Zone: 450, 460
Visual inspection of environment drains and exhaust pipe for
791102 evidence of excessive oil leakage. G.E. MM
Zone: 430, 440
Visual inspection of oil cooler impending leakage inspection
791108 hole at the 12 o’clock position on oil cooler. G.E. MM SEI 576
Zone: 430, 440 72-00-00
NOTE: If oil cooler with inspection/weep hole installed
Visual inspection and cleaning of 7:30 o’clock exhaust strut oil
G.E. MM SEI 576
791110 supply tube drain hole. 79-00-00
Zone: 430, 440
Mech.
Inspect the propeller gearbox lubrication-filter impending
G.E. MM SEI 576
791201 bypass button and change filter if necessary. 72-10-00
Zone: 451, 461
Insp.
Visual inspection rudder tab from ground for evidence of
272202 hydraulic fluid leakage from damper. JC:272202
Zone: 326
General walk around inspection of the A/C to detect any
erosion, accumulation of volcanic ash, or aircraft- and/or engine
damage or system degradation:
- static discharges for integrity;
- wing leading edges
- -
- navigation and landing lights, radomes
- horizontal and vertical stabiliser
- all extruding structure
- pitot tubes and static ports
- engine inlets and nacelles
- Issue a CRS for the Daily Check in tech log. PART 145.A.50

NOTE: Based on the results of the above inspections, more detailed inspections may be necessary.
Report any encounter with volcanic ash, or any other relevant findings, to the DOT LT Technical
department for further instructions.

Registration _____________ Inspection performed:

Date _____________
UTC time _____________

Revision No. 1, 22-07-2010 Page - 2 of 2