DIVISION 1 – General Requirements

PRODUCT DESCRIPTION:
OptiNet® Demand Control Ventilation (DCV) System
Capture, sense and control… that's at the very heart of
the OptiNet system. This groundbreaking system captures
air samples from specific building locations and sends
these air samples to a centralized suite of sensors.
OPTINET
The OptiNet® patented system remotely takes air
samples throughout a building and sends them to the
centralized sensor suite. This constant measuring of
critical indoor environmental levels is the basis of
actionable information used by building ventilation
systems to adjust to changing conditions. This results in optimum energy efficiency and
increased Indoor Environmental Quality.
Bar-raising architecture
Capture, sense and control… that’s at the very heart of the OptiNet system. This
groundbreaking system captures air samples from specific building locations and sends these
air samples to a centralized suite of sensors. By using a single bank of high quality sensors,
the accuracy of the measurements increase while significantly lowering life cycle costs
associated with keeping the system accurately calibrated. The sensor data is routed to the
building ventilation controls to adjust ventilation rates based on “real time” information.
The issues of remote sensors solved
AirGenuity has solved the issues of traditional sensing systems by using centralized sensors.
Analyzing air samples with a single sensor generates a true differential measurement that
greatly increases system accuracy. That means higher quality sensors can be deployed to
measure more critical parameters that in turn reduces the number of sensors required. A
major benefit of this is the lowering of life cycle costs with our cost-effective scheduled
calibration service. As a result, you can rely on AirGenuity for accuracy and effectiveness…
now and for years to come.
OPTINET APPLICATION
With the OptiNet System from AirGenuity you don’t have to sacrifice occupant safety,
comfort or productivity to make your commercial facility’s ventilation more energy efficient.
AirGenuity’s smart, centralized suite of sensors can be set up for a wide variety of
applications and buildings.
OPTINET COMPONENTS
A wide range of a facility’s indoor environmental data is continuously being collected by the
OptiNet® system. First gathered from individual spaces and the air handler, air samples are
then sent to the Sensor Suite for analysis. Once analyzed, the results are communicated to
the Building Management System and airflow is adjusted to improve Indoor Environmental
Quality while reducing energy costs. In addition, the air sample data is also transmitted to the
web-based AirGenuity Knowledge Centre for archiving, review, and report generation.
OPTINET OPERATION
The OptiNet system provides “real time” monitoring and control of a facility’s ventilation by
the continuous collection of a variety of building environmental data. The Air Data Router
gathers air samples from different areas. These samples are then multiplexed through the
OptiNet network to be analyzed by the Sensor Suite. This analysis data is communicated to
your Building Management System, allowing you to control airflow that reduces energy costs
and improves Indoor Environmental Quality. It is also transmitted to the web-based
AirGenuity Knowledge Centre for archiving, review, and report generation.
REFERENCE: OptiNet® Demand Control Ventilation (DCV) System – AirGenuity Inc. - Sweets
(construction.com)

DIVISION 2 – Existing Conditions

SLOPETAME3 - Erosion Control System
Made From 100% Recycled Plastic
Slopetame3 provides an immediate and permanent solution to erosion and sedimentation
problems. Using the trademark interlocking ring-on-grid design with the added benefit of
crossbars on every row Slopetame3 is a reinforcement and stabilization system. The attached
geotextile filter fabric will never come off and allows for the growth and containment of
vegetation. Even with only a 1” depth required Slopetame3 can permanently stabilize slopes
with angles up to 45 degrees.
Description and Applications
The 100% recycled plastic rolls are lightweight and easy to install. Secured with a provided
duckbill anchor and single rebar, one person can install 430 sf of product in approximately 10
minutes. Slopetame3 can be bent and trimmed with pruning shears to achieve curves, avoid
trees and create custom layouts.
Made in the USA
Tame These Applications

 Steep Slope Erosion Control

 Bank Stabilization
 Vegetated Swale Applications
 Stormwater Infiltration Trenches
 1:1 Slope Erosion Control
The Slopetame3 Benefits

 Permanent Stabilization
 Vegetation Containment
 Controlled Porosity
 Lightweight and Easy to Install
 UV Resistant
 100% Recycled Plastic
Roll Sizes
Manufactured in 1 square meter units (3.3′ x 3.3′) and assembled into rolls 1m x 10m or 2m x
20m. Rolls can be cut as needed on site with pruning shears. Some curves can be achieved
without cutting.
 Size: 2 roll sizes
 Color: black - standard, color - custom order
 Weight: 2.0 kg/m2 (.42 lbs/sf)
 Strength: 1120.69 kg/cm2 (15,940 psi) when filled with sand.

Technical Specification - Slopetame2 Slope and Channel Protection

CSI Master Format 31 25 14.16 Rolled Erosion Control Mats and Blankets
(Section 02370 Erosion and Sediment Control)
PART 1 - GENERAL
1.01 General Provisions
A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of
this Section.
1.02 Description of Work
A. Work Included:
1. Provide Slopetame2 units, anchors and installation per the manufacturer's instructions
furnished under this section.
2. Provide and install “topsoil” fill material to fill the Slopetame2 units.
3. Provide vegetation materials and installation.
4. Provide maintenance for Establishment period.
B. Related Work:
1. Grade and prepare the slope and surface soils to receive and support Slopetame2
product and vegetation cover, under Section 02200 - Earthwork.
1.03 Quality Assurance
A. Follow Section 01340 requirements.
B. Installation: Performed only by skilled work people with satisfactory record of
performance on landscaping or erosion control projects of comparable size and quality.
1.04 Submittals
A. Submit manufacturer's product data and installation instructions.
B. Submit a 10" x 10" section of Slopetame2 product for review. Reviewed and accepted
samples will be returned to the Contractor.
C. Submit material certificates for “topsoil” fill materials.
1.05 Delivery, Storage, and Handling
A. Protect Slopetame2 material units from damage during delivery and store under tarp
when
time from delivery to installation exceeds one week. Fabric backing materials are
photosensitive and can be permanently damaged by sunlight.
1.06 Project Conditions
A. Review installation procedures and coordinate Slopetame2 work with other work
affected.
B. All hard surface construction adjacent to Slopetame2 areas, including concrete and
asphalt, must be completed prior to installation of Slopetame2.
C. Cold weather:
1. Do not use frozen materials or materials mixed or coated with ice or frost.
2. Do not build on frozen work or wet, saturated or muddy sub grade.
D. Protect partially completed installation areas against damage from other construction
traffic when work is in progress.
E. Protect adjacent work from damage during Slopetame2 installation.
PART 2 - PRODUCTS
2.01 Availability
A. Manufacturer: (Slopetame2) Invisible Structures, Inc., 3510 Himalaya Road, Suite 200,
Aurora , Colorado 80011. Phone 303-233-8383,
B. Local Sales Representative:
(Contact Manufacturer, or visit www.invisiblestructures.com)
2.02 Materials
A. Slopetame2 Paving Units:

1. Lightweight injection-molded plastic units 0.5x0.5x0.025m (20"x20"x1" high, 2.7 ft2

each) with hollow rings rising from a strong open grid, with full depth crossbars between
rings spaced periodically, and a geotextile fabric heat fused to the bottom of the grid.
2. Unit weight = 540 g (40 oz.), volume = 8% solid.
3. The plastic shall be 100% post-industrial recycled HDPE plastic resins, with minimum 3%
carbon black concentrate added for UV protection.
5. Units are shipped in pre-assembled rolls that vary from 10 square meters (108 sf) to 50
square meters (538 sf).
6. Male/Female Fastener Tensile Strength, determined using a Pull Test, is equal to
80,208 N/m (450 lbsf/in.)
7. Standard color is black
Any products failing to meet these standards will be rejected.
B. Topsoil Fill: Shall consist of loose friable loam reasonably free of admixtures of subsoil,
refuse, stumps, roots, rocks, brush, weeds, or other material which would be detrimental
to the proper development of vegetative growth.
C. Anchors:
1. Primary anchorage shall be provided by Duckbill 68 anchors, or greater, with loop
end of cable secured over 0.75” dia. steel reinforcing bar (with corrosion protection in
aggressive soils). Duckbill anchor only to be supplied by Manufacturer at a rate of
one anchor per 10 m2. Surfaces subjected to heavy water submersion or action, shall
require Duckbill/rebar anchors spaced at 1 per 2 m (6.6’) on center.
2. Secondary anchorage shall be anchor pins made of either heavy gauge (8 - 12) wire
"U" shaped, or 8" long nails with "fender" type washers 5 x 30 mm od (0.25" id x
1.25" ), all galvanized metal or similar coating to resist corrosion.
PART 3 - EXECUTION
3.01 Inspection
A. Examine slope grading and soil compaction conditions. Do not start Slopetame2
installation until unsatisfactory conditions are corrected. Check for improperly
compacted or prepared surface soils, debris, and/or improper gradients.
B. Installation constitutes acceptance of existing conditions and responsibility for
satisfactory performance. If existing conditions are found unsatisfactory, contact Project
Manager for resolution.
3.02 Preparation
A. Place Slopetame2 Units over prepared grades as shown on plans. Allow 25 mm (1.0") for
Slopetame2 unit thickness and “topsoil” fill to reach Final Grade.
3.03 Installation of Slopetame2 Units
A. Install the Slopetame2 units from the top of the slope to the bottom, by placing units with
rings facing up, and using small posts/holes provided along each edge to maintain proper
spacing and interlock the units. Crossbars on the product shall be installed to be in
opposition to the direction of primary water flow. Cutting can be performed with
pruning shears and knife. Units shall be anchored with Duckbill/rebar anchors across the
top of the mat (top of slope) and across the middle of the mat. If any part of a
Slopetame2 mat shall be covered by water (channel or pond surface), then the bottom and
leading edges exposed to water flow shall receive additional Duckbill/rebar anchors as
needed to prevent undercutting by water movement. Additional wire anchor pins shall be
spaced at one per square meter, or more as required to secure units in place and resist
sliding when filled. Tops of rings shall be flush, or slightly below the surface of adjacent
hard surfaces. Remove Slopetame2 product where existing trees, shrubs, rocks, or
similar elements will project above the surface, and secure cut edges with anchor pins.
B. Install “topsoil” into rings after the units are anchored by "up-dumping" from a Gradall,
or from buckets, taking care not to snag the mat with bucket edges or teeth. The
“topsoil” is then spread using stiff bristle brooms in an uphill direction to fill the rings,
with the finish grade no more than 6 mm (0.25") above top of rings. Do not allow

motorized equipment access over the Slopetame2 area during installation and
Establishment.
C. Identify locations of plant materials with root balls larger than 10 cm dia. (4”), remove
topsoil and Slopetame2 from an area two times (2x) the diameter of the root ball,
excavate hole large enough for the root ball, place new plant, and backfill with “topsoil”
material. Set the crown of the root ball and backfill material 12 mm (0.5”) below the top
of the adjacent rings. Place anchor pins into the Slopetame2 structure above and below
the hole for the new plant.
D. Install seeded vegetation by Hydro-seeding methods, incorporating an appropriate
cellulose type mulch material in the hydro-seeding mixture. This mixture shall have a
distinctive green color to visually show the distribution of the mixture on the slope.
3.04 Cleaning
A. Remove and replace segments of Slopetame2 units where nine or more adjacent rings are
broken or damaged, reinstalling as specified, with no visible evidence of replacement.
B. Perform cleaning during the installation of work and upon completion of the work.
Remove from the site all excess materials, debris, and equipment. Repair any damage to
adjacent materials and surfaces resulting from installation of this work.
REFERENCE: SLOPETAME3 - Erosion Control System – Invisible Structures - Sweets
(construction.com)
DIVISION 3 – Concrete
PRODUCT DESCRIPTION:
Cement is a binding agent that, when mixed with sand, stone or
other aggregates and water, produces either ready-
mix concrete or mortar.
PRODUCT PACKAGING: per sack
PRODUCT PREPARATION PROCEDURE:
In the wet process, the raw materials are mixed with water to
form slurry, which is fed into a kiln. Fuel costs are greater in the
wet process than in the dry process because the water that is
added to the raw materials to form slurry must be evaporated during the clinker
manufacturing process. The clinker is then cooled down, mixed with gypsum and fed in
specified proportions into a cement grinding mill where they are ground into an extremely
fine powder and mixed with grinding aids including admixtures (which control properties of
the concrete including plasticity, pumpability, freeze-thaw resistance, strength and setting
time) and other cement additives, which we produce or source from third parties, to produce
finished cement.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
Groundwork
Readymix Concrete should be laid on well compacted hardcore sub-base that has been
covered with a thin layer of sand and a layer of plastic sheeting. This prevents excessive
moisture loss from the concrete and acts as a damp proof membrane, when used in concrete
floors.
Estimating
You need, and obtain a “delivered price”, call your local sales office with details of the area to
be concreted and average thickness required. Other information e.g. slope, drainage and
accessibility may also be useful. Alternatively, you can calculate how much you need by using
Cemex concrete calculator
Clear site
Prepare the site carefully by removing stones and weeds plus a layer of top soil. Level off
bumps with a spade to create a flat surface
Formwork
This is the frame which will keep the concrete in place as it hardens. 25mm thick timber strips
are ideal. Nail them to wooden pegs driven into the ground at 1m intervals (on the outside of
the formwork). Lay plastic sheeting over the area, and weight with bricks or stones.
Setting a fall
Plan the slope to allow water to run off easily. Check the forms with a spirit level, and make
one side lower to allow drainage away from buildings. Normally allow about a 25mm drop for
a 1 metre run.
Joints
If the area you’re laying measures more than 4m in any direction, you’ll need to divide it into
sections. Also if it is less than 500mm wide, the length should be reduced to 3m. Lay joints of
softwood board about 10-12mm thick across the formwork, to the full depth of the slab, at
the required intervals. Support them with pegs that can be removed as each section is
completed. If your slab will adjoin an existing slab or building, make a joint between the two
with a strip of thick bituminous felt.
Spreading
Spread concrete between forms to a level 10mm to 15mm higher than the finished surface
Compact the concrete using a tamping beam
Levelling
With one person each end holding the tamping beam, lift approximately 100mm and then
drop into the concrete ensuring that each end of the beam is over the formwork
Level the concrete by ‘sawing’ the beam from side to side whilst advancing it slowly forward
Remove excess concrete with a rake/shovel
Level using rake to fill area 10-15mm higher than finished surface.
Compact with tamping beam.
Shuffle tamping beam from side to side to level.
Finishing
A tamped surface provides a rough low-slip finish suitable for drives, paths, external slabs
A wood or plastic float finish provides a smooth but textured low-slip finish suitable for paths,
garage and workshop floors
A steel float finish provides a very smooth finish suitable for house floors, ponds, etc.
A coarse brush finish is applied just prior to the concrete setting and is suitable for paths and
drives where a rough tamped surface may be unsightly.
PRODUCT DISPOSAL PROCEDURE:
Throwing away your old concrete is not a good idea. So what do you do with old and unused
concrete? What option will you choose to dispose of it?
Here are some concrete disposal options:
 If you’re lucky, you’ll have access to a pickup truck. If not, then hire one. Be careful
while loading; make sure that you do not overload the vehicle because it will make it
heavy, which will cause the vehicle to fail or strain the engine severely.
 You can consider contacting a building materials supply company- one who operate
large-scale operations along with a large fleet of a cement mixers or gravel-hauling
dump trucks- who may take your old concrete. Some of them do that free of charge,
hauling and unloading your concrete at their location.
 Another good idea to dispose of your old concrete is to put a “free” sign beside your
pile of concrete, which may catch the eye of some concrete-needing passerby.
Although it sounds unusual, it’s worth a try.
REFERENCE: Guide To Laying & Installing Concrete | CEMEX UK
Production Process | CEMEX Philippines (cemexholdingsphilippines.com)
Cement - CEMEX
DIVISION 4 – Masonry
PRODUCT DESCRIPTION:
Concrete Hollow Blocks (CHB), are one of the most
extensively used walling materials in the Philippines.
Some of the reasons for this is their relative low cost
when compared to other materials and speed of
installation by semi-skilled labourers. CHB walls are
very weak against lateral loads (pushing or pulling
forces from typhoon or earthquake). Adding steel
reinforcing bars vertically and horizontally inside the
CHBs can increase their resistance to lateral loads.
PRODUCT PACKAGING: Per piece
PRODUCT PREPARATION PROCEDURE:
Done in two different ways
By weight or volume. The most common method is by volume (e.g. using a bucket).
Mixture
For CHBs: Mix Proportion 1:7, as per structural engineer’s specification.
Water
Clean water should be used. Shall not exceed 28 litres per 40 kilograms per bag of cement,
slump test (as per ASTM C-143) shall not exceed 10cm, unless specified by a structural
engineer.
Common CHB mix
½ bucket of water, 1 bucket of cement, 7 buckets of sand.
Common mortar mix
1 bucket of water, 1 bucket of cement, 5 buckets of sand
Mixing time
If batch mixer is used, use accurate timing and measuring devices to operate as per
manufacturer’s instructions. Revolutions should be between 14 and 20 per minute.
Curing
After being removed from the mould, the CHBs should be covered with a plastic sheet or
tarpaulin and kept damp and shaded for at least 7 days in order to effectively cure. This can
be achieved by continually spraying them with water or keeping them under water in tanks.
A good curing process leads to less cracking and a stronger, harder, denser and more durable
concrete.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
All concrete hollow block will be carried out in accordance with the specification and
Project Quality Plan.
Handling and Storage of Materials
Blocks shall be delivered to site palletized, off loaded as near to the point of use
as practicable on a clean hard surface free from contamination by mud or surface
water.
Cement shall be stored off the ground, kept dry and used in order of delivery.
Store metal ties and straps under cover and protect them from damage and
distortion.
Preparation of Work, Materials and Components
When the materials and components are distributed to the work area, ensure that
the structure is not overloaded.
Plan for scaffolding material required for block work at heights. Plan for
additional manpower for lifting blocks at heights.
Set out anticipating the position of openings etc. in the work above to avoid
unnecessary cutting and adjustment of masonry units leading to incorrect or uneven
bonding.
Preparation of Mortar Mixes
Mortar shall be mixed by machine except for small quantities only (not
containing plasticizer). Hand mixing (if permitted) may be done on a watertight
platform.
Use mortars (other than retarded mortars) within 2 hours of mixing or as
specified.
Laying of Concrete Hollow Blocks
Spread the mortar along the corner
Use your trowel to spread a few slabs of mortar around the corner's base of the
footing. Spread the mortar 1" deep and 8" wide in the marked area. Continue to
spread the mortar to account for the distance of about three to four blocks.
Rebar should be on-place whenever laying is on-going.
Set the corner block
It is important to lay the corner block down first. Again, use a corner block if
they're available. Setting the corner first will ensure an even dispersal of the rest
of the blocks.
Apply mortar to the side
Apply mortar to each side of the concrete block using your trowel. You'll need to
apply at least an inch to each side. Once applied, position the block in the desired
location. Try to align the corner to the string set up earlier. Don't apply mortar to
outer edge of the corner. Try not to leave any gaps when applying mortar, or it’ll
weaken the bond between the blocks.
Continue to lay the concrete blocks
Start laying blocks from the corner or edge of the wall so you can work in one
direction. Apply mortar at the end of the block before you place the block
adjacent to it.
Check the Alignment
Before stacking more concrete blocks on top of your initial foundation, check if
everything is aligned. Use your mason's level by laying it on the first set of blocks.
Check both the outside and center section of the bricks. Tap the blocks for any
alignment adjustments while the mortar is still wet. Do not try to move a block
after the concrete has set. Measure the length and height every two or three
layers.
Apply mortar to the top
Place the mortar 1 inch (2.5 cm) deep and use the same width as the width of the
block. You can then spread the mortar so it covers the length of about 3 blocks in
the direction that you are laying the blocks.
Stack the blocks
Lay the block down on top so the edge of the top block aligns with the halfway
mark of the bottom block. You'll recognize the pattern as a standard among the
construction sites. The top block will fit in between two bottom blocks.
Add reinforcement
If you built high walls, consider adding reinforcements. You can also use
reinforcements if the ground pressure on the site is not stable. Place the 1/4"
reinforcement rods into the openings with the ends overlapping about 2" or 3"
PRODUCT DISPOSAL PROCEDURE:
Step 1
Sort your concrete blocks into two categories: those that can be reused and those that
cannot. Concrete blocks that are chipped or broken should not be reused for building, but
they can still be recycled.
Step 2
Locate green contractors near you through the Green Contractor Guide (see Resources). Call
matching local contractors to see if they need cinder or concrete blocks for building projects.
If someone wants the blocks, arrange to have them removed. In this way, you don't have to
transport the blocks in your car for recycling, and you save resources because the blocks can
be reused in their current state without being processed.
Step 3
Find recycling centers near you that accept concrete blocks by going to Earth 911 (see
Resources). Enter your city or zip code in the location blocks and type "Concrete" in the
search bar. Then call matching recycling centers to find out when they are open. Load the
concrete blocks into your car or truck and drive them to the recycling center. Dispose of all
broken or subpar blocks in this manner, along with concrete blocks you can't give to a
contractor.
REFERENCE: Key Messages CHB V1.1.pdf (sheltercluster.org)

DIVISION 5 – Metals
PRODUCT DESCRIPTION:

Aluminum Angle Bar (YIEH CORP.)

The advantages of aluminum alloy are lightweight,
excellent electrical and thermal conductivity, high
corrosion resistance and ductility. Aluminum alloy is soft
and usually alloyed with copper, zinc, magnesium, silicon,
manganese and lithium to increase strength. When
aluminum alloy is exposed to air, an anti-oxidant coating
will be formed instantly to protect products. Aluminum
alloy is one of the lightest metals. The application of products ranges from precision
technology to daily commodities.
PRODUCT PACKAGING:
DIMENSION RANGE

A 10mm~200mm
 B 10mm~200mm

T 2mm~15mm

Length 1,000~6,000mm
PRODUCT PREPARATION PROCEDURE:
Temper Definition

O Annealed

Slightly strain harden from working at an elevated

H112
temperature or from limited amount of cold work

Cooled from an elevated temperature shaping process and

T5
then artificially aged

T6 Solution heat-treated and then artificially aged

Solution heat-treated and then artificially aged - mechanical

T66 property level higher than T6 achieved through special control
of the process (6000 series alloys)

PRODUCT APPLICATIONINSTALLATION PROCEDURE:

Application
Aluminum angles are used in numerous industrial applications, including scaffolding,
shipbuilding, transmission towers and furniture applications.
- Production Process: Extruded
- Form & Image: Equal Angle, Unequal Angle
- Surface Finish: Mill Finish, unless otherwise specified
- Surface Protection: Paper interleaved
CHEMICAL COMPOSITION:
Oth Oth
All ers: ers: Al:
Si Fe Cu Mn Mg Cr Zn Ti
oy Eac Tot Min.
h al

50 0.40 4.0~4 0.05~ 0. 0. 0.0 0.1 remai

0.40 0.40 0.10
83 ~1.0 .90 0.25 25 15 5 5 nder
 Oth Oth
All ers: ers: Al:
Si Fe Cu Mn Mg Cr Zn Ti
oy Eac Tot Min.
h al

60 0.30~ 0.10~ 0.35~ 0. 0. 0.0 0.1 remai

0.10 0.10 0.05
60 0.60 0.30 0.60 15 10 5 5 nder

60 0.40~ 0.15~ 0.80~ 0.04~ 0. 0. 0.0 0.1 remai

0.70 0.15
61 0.80 0.40 1.20 0.35 25 15 5 5 nder

60 0.20~ 0.45~ 0. 0. 0.0 0.1 remai

0.35 0.10 0.10 0.10
63 0.60 0.90 10 10 5 5 nder

60 0.70~ 0.40 0.60~ 0. 0. 0.0 0.1 remai

0.50 0.10 0.25
82 1.30 ~1.0 1.20 20 10 5 5 nder

64 0.20~ 0.45~ 0. 0.0 0.1 remai

0.15 0.20 0.05 - -
63 0.60 0.90 05 5 5 nder
REFERENCE: Aluminum Angle Bar (yieh.com)

PRODUCT DESCRIPTION:
HOT ROLLED REINFORCING BAR (YIEH CORP.)
known when massed as reinforcing steel or
reinforcement steel, is a steel bar or mesh of steel
wires used as a tension device in reinforced
concrete and reinforced masonry structures to
strengthen and aid the concrete under tension.
Concrete is strong under compression but has weak
tensile strength. Rebar significantly increases the
tensile strength of the structure. Rebar's surface is often "deformed" with ribs, lungs or
indentations to promote a better bond with the concrete and reduce the risk of slippage.
PRODUCT PACKAGING:
Bundle Weight: about 3MT per bundle (uniform counting pcs)
12M / 9M Length rebar can be folded loaded into 20 ft container

PRODUCT PREPARATION:
First, most rebar produced in North America is produced using an EAF steel making process,
or Electric Arc Furnace. Here, scrap steel is collected from various sources at the steel mill
and put into a large ladle where the steel is then melted at temperatures up to 1,800°
Fahrenheit.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
Application
Carbon steel bar is a kind of general-purpose steel bar that offers excellent formability and
weldability, being used in a wide variety of applications including auto manufacturing,
shipbuilding, aerospace industry, petrochemical plants, auto-power and wind-engine,
metallurgical machinery, precision tools, etc.
- Auto manufacturing
- Aerospace industry
- Auto-power and wind-engine
- Metallurgical machinery
Air cool quality with alloy added (Boron or Vanadium)
Size: 6mm~50mm (Full Size Range Supply)
6mm/8mm/10mm/12mm x Coil
12mm~50mm x Length 6m / 9m / 12m
Rebar in Coil
Coil ID: 850mm Min.
Coil OD: 1100mm Max.
Coil Weight: about 2MT
REFERENCE: Hot Rolled Reinforcing Bar (yieh.com)

DIVISION 6 - Wood, Plastics, Composites

PRODUCT DESCRIPTION:
Sanded Plywood ( Murphy Plywood )
Sanded plywood is a structural plywood panel with face and
back plies that are sanded smooth in the manufacturing process.
The panels have three or more cross-laminated layers of wood
veneer, each layer consisting of one or more plies. Face plies are
B-grade or better veneer as defined in U.S. Product Standard PS
1-09 for Structural Plywood.
PRODUCT PACKAGING:
To order sanded plywood, designate the Performance Category,
APA trademark, grade, Group number, bond classification, dimensions, and number of
pieces. For example: Performance Category 3/4, APA A-C, Group 1, Exterior, 48" x 96", 100
pcs.
PRODUCT PREPARATION PROCEDURE:
The ease with which sanded plywood can be cut, drilled, routed, jointed, glued, fastened and
finished with ordinary tools and basic skills is another of its many advantages. Support panels
firmly with the best side up when hand sawing or when using a radial-arm or table saw. Cut
with the best side down when using a portable power saw. Plywood also can be die cut and
stitched. Performance Categories up to and including 3/8 can be die cut with little difficulty.
Some experience and specialized techniques are necessary to cut thicker panels. Grades with
a minimum of defects provide the smoothest cut and Exterior panels are preferred to
Exposure 1 panels. Fabric or plastic materials can be stitched to panels up to Performance
Category 3/8 with industrial sewing machines. Ultimate test values in excess of 100 pounds
per lineal inch have been achieved with fabrics stitched to plywood with Performance
Category 1/4.

PRODUCT APPLICATION/INSTALLATION PROCEDURE:

Construction APA sanded plywood finds numerous uses in both residential and
nonresidential construction, and for both new construction and remodeling projects. Typical
construction applications include soffits, stair treads and risers, cabinets and built-ins,
shelving, paneling, and accent panels. Sanded plywood, with special inner-ply construction
for resistance to indentation and punctures from concentrated loads, is ideal as an
underlayment base for thin resilient floor coverings and high performance floor or roof deck
coatings. Sanded plywood is widely used for paneling, accent walls, counter tops and fronts
and other interior applications in commercial structures. Easy to stain attractively, plywood in
these applications contributes the warmth and natural beauty of real wood while meeting
project cost constraints. Sanded plywood is an ideal choice for cabinets, built-ins, shelving
and similar applications for the same reasons – good looks and reasonable cost. Panels are
also commonly used as a backing for other finish materials in these and other applications.
For walls, for example, plywood serves as an excellent backing for wall coverings such as rare
hardwoods, vinyl surfaces and decorative fabrics.
Do-It-Yourself Applications
There are few materials more widely used or ideally suited for miscellaneous homeowner
and do-it-yourself applications than APA sanded plywood. The uses to which it can be put are
limited only by the imagination and woodworking skills of the user. Typical do-it-yourself
applications include workbenches, tool and toy boxes, desks and tables, other furniture of all
kinds, outdoor storage buildings, patio shelters, fences, and countless home repair and
maintenance projects.
Interior Applications
A wide variety of finishes are available for sanded plywood used in interior applications. The
most common are described below. Always use finishes formulated for wood and follow the
finish manufacturer’s recommendations for best results. For interior (and exterior)
applications, little or no sanding of the mill-sanded plywood surface is advised before
application of the finish, to avoid uneven highlighting of hard and soft grain areas on the
surface of the panels.
Exterior Applications
Sanded plywood is not recommended as an exterior siding on most buildings. However, it is
frequently used for soffits and miscellaneous other exterior uses. For these applications,
acrylic latex house paints are recommended. House paints require at least two coats, a
primer and topcoat. Primers are formulated specifically for controlled penetration, optimum
bonding to the substrate, and minimal extractive staining. Some acrylic latex systems use oil
or oil-alkyd primer followed by the acrylic latex topcoat. Other systems use one or two coats
of a stain-blocking acrylic latex primer and generally offer superior performance. In any case,
select companion products that are designed to be used together and preferably from the
same manufacturer. Two topcoats will provide significant improvement in the life and
performance of the finish.
PRODUCT DISPOSAL:
Engineered wood products are a good choice for the environment. They are manufactured
for years of trouble-free, dependable use. They help reduce waste by decreasing disposal
costs and product damage. Wood is a renewable resource that is easily manufactured into a
variety of viable products.
REFERENCE: Product Guide: Sanded Plywood (murphyplywood.com)

DIVISION 7 – Thermal and Moisture Protection

PRODUCT DESCRIPTION:
Crommelin® Shower Waterproofing Membrane is a waterbased,
ready to use, heavy duty, modified rubber liquid applied
membrane, engineered to permanently waterproof wet areas prior
to tiling. Crommelin® Shower Waterproofing Membrane delivers a
keyed finish, suitable for use with cement based tile adhesives.
PRODUCT PACKAGING:
Shower Waterproofing Membrane is available in 1L, 4L and 15L
pails plus 4L and 6L kits.
• 1L produces 1m2 of finished membrane.
• 4L / 4L kit produces 4m2 of finished membrane.
• 6L kit produces 6m2 of finished membrane.
• 15L produces 15m2 of finished membrane.
PRODUCT PREPARATION PROCEDURE:
• Concrete must have cured for at least 28 days, screeds and renders 7 days.
• All substrates must be installed as per manufacturer’s recommendations.
• The surface should have a light even texture. Masonry should be flush pointed and all
defects in existing surfaces made good.
• Surfaces must be clean, dry, sound and free from dust, grease, curing compounds, release
agents, loose particles, efflorescence, concrete laitance or any other contaminants.
• All high points and protrusions should be removed, blow-holes and areas of honeycombing
should be filled and the surface should be brought back to an even profile using a suitable
repair mortar.
• All surfaces must be dry. A moisture test is required 100% of the time to ascertain if the
substrate is dry enough to coat. Electronic moisture meters are recommended.
• If minor surface consolidation is required, apply one coat of 1:1 dilution of Shower
Waterproofing Membrane and water and allow to dry.
• If a greater amount of surface consolidation is required, apply one coat of Crommelin®
Powerflex as per recommended application rates.
• If substrate is not dry, prime surface with Crommelin® Dampstop as per specifications.

PRODUCT PREPARATION
• Shower Waterproofing Membrane is ready to use, simply stir well prior to application.
PRODUCT APPLICATION/INSTALLATION PROCEDURE
APPLICATION CONDITIONS
• Do not apply if surface/ambient temperatures are too high or too low. Recommended
temperature range 10⁰C - 35⁰C.
• Do not apply if humidity is too high, or likely to be during the initial cure phase. Maximum
recommended humidity during application and cure is 85%.
• Weather details may be checked at http://www.bom.gov.au
APPLICATION PROCESS
Full application instructions can be found at www.crommelin.com.au/full-instructions/
• Bond breaking sealant/tape to all joints, junctions, protrusions, angles and internal corners
must be used. The use of Crommelin® Polyurethane Sealant, Crommelin® Silicone WP Plus or
Crommelin® Reinforcing Fabric with Bond Breaker is recommended.
• The use of Crommelin® Reinforcing Fabric is also recommended for use at all junctions to
protect vulnerable areas from damage.
• Apply first coat evenly, as per recommended coverage rate and allow to dry.
• Recoat when touch dry, after approximately 2 hours.
• Apply second coat evenly, at 90º (right angles) to first coat and allow to dry.
• Ensure membrane is protected from damage before tiling.
RE-COAT/DRYING TIME
• Recoat time: 2-4 hours.
• Tile over: after a minimum of 48 hours.
• Flood test: after 48 hours, pond to a depth of 25mm for 2 hours and remove testing water
immediately.
• Full cure: 7 days.
COVERAGE
• 2m2/L per coat – minimum 2 coats required.
• Complex or highly irregular surfaces may require additional coats.
CLEAN UP
• Clean all equipment with water before product dries.
• Uncured material may be removed with warm water and detergent.
SAFETY AND FIRST AID
Crommelin® Shower Waterproofing Membrane Safety Data Sheet is available from
Crommelin upon request.
Safety
• Ensure good ventilation and avoid breathing vapours.
• Avoid skin and eye contact. Wear gloves and eye protection. Remove splashes on skin
immediately and remove contaminated clothing.
• Keep out of reach of children.
• Keep container sealed when not in use.
• Do not swallow.
First Aid
• If poisoning occurs, contact a doctor or poisons information centre: Ph. 13 11 26.
• If swallowed, do not induce vomiting. Give a glass of water to drink.
• If in eyes, hold eyes open and flood with water for at least 15 minutes.
• If not breathing, apply artificial respiration.
REFERENCE: 20af0d3d-d02d-440b-8482-77c13f3b1397.pdf (rackcdn.com)

DIVISION 8 – Openings
PRODUCT DESCRIPTION:
Casement window ( AmesburyTruth )
Truth's Casement SafeGard(TM) WOCD provides a means so
that the window, when opened in an initial operation, will limit
the venting to less than 4".
PRODUCT PACKAGING:
It is designed to fit in the standard hinge cavity of 0.719"W X
0.438"H.
PRODUCT PREPARATION PROCEDURE:
Reliable operation and made entirely of austenitic stainless
steel and plastic. WOCD was tested and certified to ASTM
F2090-10. It is designed to fit in the standard hinge cavity of 0.719”W X 0.438”H (nominal).
Arm assembly has a decal with simple operating instruction, and track is assembled with
visible colored plastic to discern the separate operations.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
For ease of installation, the track will self locate to the frame. The arm is located on the sash
using a template (#92251) with printed instructions. Please see Fig.1 for installation
dimensions on window mounting surfaces. For additional information, please see installation
and operating instructions. (www.truth.com/instructions)
WARRANTY:
Protected under the terms of the Truth Warranty for Window and Door Manufacturers and
Authorized Distributors. Refer to Truth’s Terms and Conditions for further details. MATERIAL:
Austenitic stainless steel track, arm, rivet, and Delrin cover and tab. This device is
recommended to be installed with stainless steel screws. Total of 4 stainless steel #7
undercut Phillip Flat Head screws to be used in this application; two for the track and two for
the arm. Due to variation of profile, screw length can vary. Please refer to application print
specific to your profile and installation instruction for more details.
INCLUDE TRUTH SPECS IN YOUR NEXT PROJECT REQUIRING A WINDOW OPENING CONTROL
DEVICE:
Window Opening Control Devices as required by ASTM F2090-10, the standard specification
for window control devices with emergency (egress) release mechanisms. Product will limit
the window opening to less than 4” and requires two actions to release the device allowing
the window to open fully for egress purposes. Actions to release the device for egress
purposes are to be performed without the use of keys, tools or special knowledge. WOCD will
automatically re-latch when window is fully closed. This WOCD shall be “SafeGardTM
Casement Window Opening Control Device” as offered by Truth Hardware, Owatonna, MN.
TRUTH TIPS:
1. Truth recommends that a casement WOCD be used in casement application where
applicable and building codes require such application. Please check the local building codes
for applicability and egress size requirements.
2. Casement WOCD can be factory installed or field retrofit on all profile material types
where standard/nominal (0.719”W X 0.438”H) hinge cavity is available. Please observe all
safety instructions and consult window manufacturer when you have questions or concerns.
Please contact Truth sales for application to ensure form, fit, and function for your specific
window application
3. Standard 2 walls (vinyl, fiberglass, aluminum and other composite materials) on the profile
is required for proper screw retention
4. Correct handing with proper installation are important to ensure proper operation of the
device
5. For additional product information or installation and operating instruction, please go to
www.Truth.com/instructionvideos for more detail.
Note:
1. This device is not designed for Awning application.
2. * Specific SKU to be ordered separately for OEM application
REFERENCE: HW11 SafeGard.r2.pdf.pdf (truth.com)
DIVISION 9 – Finishes
PRODUCT DESCRIPTION:
BOYSEN® Epoxy Primer a high quality, two-component, epoxy-
polyamide system that has exceptional adhesion to practically any
surface including steel tanks, coastal installations, galvanized iron,
pipelines, aluminum, structural steel, etc. Has excellent corrosion
resistance and sealing properties. Highly alkali-resistant so there is
no need for neutralization of new concrete.
PRODUCT PACKAGING:
BOYSEN® Epoxy Primer comes in 4-liter cans,  ¾ full packed with
Curing Agent in a 1-liter can
PRODUCT PREPARATION PROCEDURE:
Concrete Flooring:
Remove oil and grease by detergent cleaning.  For very smooth floors, acid etch smooth
surfaces to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part
water. Apply over masonry and let stand for 2-3 minutes. Rinse with water. If available, rinse
by pressure washing. Finished acid etched texture should be similar to that of 40-60 grit
sandpaper. Make sure that the surfaces to be painted are clean and dry.
Caution: Adequate protection and ventilation should be provided when working with acids.
Metal:
Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax  and
other foreign matter. For new G.I. sheets, etch the surface by applying 10% BOYSEN ® Metal
Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting on surfaces with alkyd or lacquer based coatings, scrape off all paint. Remove oil
and grease by detergent cleaning followed by scuff sanding.  To remove rust, wire brush or
scrape affected areas and apply BOYSEN® Metal Etching Solution #71. Let it stay for 10-15
minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying
paint. Primer should be applied immediately after treatment.
PAINTING SCHEDULE:
Concrete Flooring:
Mix three (3) parts of BOYSEN® Epoxy Primer White #2200 to one (1) part of its catalyst.
Allow twenty (20) minutes induction time. Dilute 1:1 ratio with BOYSEN ® Epoxy Reducer #55.
Apply as primer coating on bare concrete. Let dry overnight. Topcoat with 2-3 coats of
BOYSEN® Acqua Epoxy™ or BOYSEN® Epoxy Enamel. Let dry overnight before recoating. Let
cure for 3 days before allowing foot traffic and 7 days for heavy duty use.
Metal:
Prime bare metal BOYSEN® Epoxy Red Oxide #2277 or BOYSEN® Epoxy Primer Gray #2230. Let
dry eight (8) hours before recoating. Topcoat with 2-3 coats of BOYSEN ® Acqua Epoxy™ or
BOYSEN® Epoxy Enamel. Let dry overnight before recoating.
NOTE: For epoxy-primed surfaces, topcoat should be applied not more than seven (7) days
after priming to ensure good intercoat adhesion. Otherwise, re-priming is needed.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
By Paint brush or spray gun
PRINCIPAL USES:
As a primer for topcoats of Epoxy Enamel or Acqua Epoxy™ to be applied on metal,
galvanized iron, wood and masonry
PRACTICAL COVERAGE:
20-25 square meter / 4 liters / coat
SURFACE DRY:
2-3 hours
DRY THROUGH:
6-8 hours
DRY FILM THICKNESS:
1.5 mils/coat
THINNING:
BOYSEN® Epoxy Reducer #55
MIXING RATIO:
3:1, paint-to-catalyst, respectively
REFERENCE: Pacific Paint (Boysen) Philippines, Inc., - Two-
component Epoxy Based Coatings - BOYSEN^®
Epoxy Primer
PRODUCT DESCRIPTION:
100% Acrylic Gloss Roof Paint (Water-Based)

DAVIES ROOFSHIELD 100% Acrylic Gloss Roof Paint- Pure waterbased acrylic emulsion gloss
paint for beautifying and protecting galvanized iron and cementitious roofs as well as
masonry walls.
PRODUCT PACKAGING:
Pack sizes: 16-liter and 4-liter cans
PRODUCT PREPARATION PROCEDURE:
Stir well before using. Use as is. If necessary, reduce with ¼ liter of water per 4 liters of paint.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
Apply by brush, roller or spray
Galvanized Iron Roofing
1. Ensure surface is cleaned with Lacquer Thinner.
2. Apply one (1) coat of Davies 941 Metal Primer Zinc Oxide Yellow by brush, roller or
spray. Allow drying for at least eight (8) hours.
3. Finish with two (2) coats of the desired color of  DAVIES Roofshield.  Let it dry for two
(2) hours in between coats.
Cementitious Roofing
1. Ensure that the surface is clean. Apply one (1) coat of DAVIES 1350 Megacryl
Concrete Primer and Sealer. Let dry for two (2) hours.
2. Finish with two (2) coats of the desired color of DAVIES Roofshield . Let dry for two
(2) hours in between coats.
PRODUCT CLEANING: Thinner or water
STORAGE AND HANDLING
 Keep container closed when not in use.
 Store in a cool, dry and well-ventilated space.
 Do not transfer contents to other containers for storage
 In case of spillage absorb with inert materials such as sand.
PRODUCT DETAILS
Excellent weatherability & ultraviolet resistance
Excellent resistance to chalking, cracking, and color fading
Excellent gloss retention
Fast drying
Environment friendly
REFERENCE: Davies Roofshield Premium Roof Paint 100%
Acrylic Technology Gloss Finish – Davies Paints Philippines, Inc.

PRODUCT DESCRIPTION:
Dutch Boy® Versatex™ is a water-based patterned finish
specially designed for interior use on primed surfaces such as
concrete, drywall, and properly primed wood. It can be applied
in several creative patterns to beautify interior walls and
ceilings.
PRODUCT PACKAGING: 4 liters
PRODUCT PREPARATION PROCEDURE:
SURFACE PREPARATION: 
New Concrete
New concrete should be allowed to dry for 14 to 28 days under normal weather conditions
before paint application. Surface to be painted should be clean, dry, free from oil, grease,
dust, dirt, and other contaminants. If painting must be done immediately within the 14 to 28
day curing period, treat the surface with a solution of 1 part Dutch Boy ® Nalcrete™ Masonry
Neutralizer 7000 diluted in 16 parts water. Apply the solution liberally using a brush or roller.
Let dry overnight before rinsing with water to remove white crystal that will have formed on
the surface. Let dry before painting. If the concrete has been cured for 28 days or more,
there is no need to apply a neutralizer.
Wooden Surfaces
Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust
off before painting. Avoid using product on high friction areas.
Drywall Subtrates
Install and secure joints as per manufacturer’s recommendations.
Repainting
Scrape off all loose, scaling, flaking, and peeling paint manually or by using a paint and
varnish remover. Wash surfaces clean and completely remove any residue. Let it dry.
For repainting concrete with chalky old paint, use a surface conditioner. In case of mildew
infestation, treat with a bleach solution (1:3, laundry bleach to water, respectively) by
swabbing or brushing. To ensure proper treatment, let stand for 24 hours before washing off
residue. Let dry.
For repainting other surfaces such as wood, follow the first step then apply the appropriate
primer before recoating.
PAINTING SCHEDULE:
Primer
Wood-Dutch Boy® Classic™ Flatwall Enamel 6510
Concrete- Dutch Boy® Nalcrete™ Flat Latex 7510
Putty
Wood-Dutch Boy® Glazing Putty 6210
Concrete- Dutch Boy® Concrete Putty 7211
Texture
Dutch Boy® Versatex™
Topcoat
Dutch Boy® Nalcrete™ Latex (Flat, Semi-Gloss, or Gloss in any color)
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
For a regular texture pattern, apply Dutch Boy® Versatex™ straight from the can using a
regular textured roller. If a different design is desired, first apply Dutch Boy ® Versatex™ with a
regular textured roller then immediately follow with the designed pattern roller while the
paint is still wet and workable. Roll in one uniform direction to impress the design onto the
surface.
FINISH:
Textured
PRACTICAL COVERAGE:
5 to 6 square meters
DRY THROUGH:
To touch: 2 hours
To recoat: 8 to 12 hours
THINNING SOLVENT: 
Do not thin. Use as supplied.
TINTING: 
Do not tint. If a colored finish is desired, top coat with Dutch Boy ® Nalcrete™ Latex Paints.
CLEAN UP  SOLVENT: 
Water
REFERENCE: - Interior Paints - Dutch Boy^® Versatex™ Interior Textured Finish

DIVISION 10 – Specialties
PRODUCT DESCRIPTION:
These Architectural Series Cabinets feature a nominal inside
box dimension of 27 inches (68.6 cm) height, 20 inches (50.8
cm) width and 8 inches (20.3 cm) depth, a capacity to house
two 20 lbs ABC fire extinguishers.
PRODUCT PACKAGING: Per piece
PRODUCT PREPARATION PROCEDURE:
Verify that rough openings for cabinets are correctly sized
and located.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
INSTALLATION A. Install the items of this Section in strict
accordance with the original design, approved shop drawings, and requirements of agencies
having jurisdiction, as approved by the Architect, anchoring all components firmly into
position.

GENERAL
1.01 WORK INCLUDED
A. Fire Extinguishers
B. Cabinets
C. Accessories
1.02 RELATED WORK
A. Section 09 91 00 — Painting
B. Section 21 11 00 — Facility Fire-Suppression
1.03 REFERENCES
A. NFPA 10 — Portable Fire Extinguishers
B. ADA Accessibility Guidelines
C. UBC Standard 7-5 (ASTM E-814-83) — Fire-rated cabinet option for combustible and non-
combustible walls
1.04 QUALITY ASSURANCE
A. Conform to NFPA 10 requirements for portable fire extinguishers.
B. Provide fire extinguishers, cabinets, and accessories by single manufacturer.
1.05 SUBMITTALS
A. Submit product data in compliance with Section 01 33 00
REFERENCE: Larsens 2016 Brochure.pdf (larsensmfg.com)
PRODUCT DESCRIPTION:
Warning signs and traffic signals are used with traffic control spikes
and auto-spikes to inform drivers that a one way lane condition exist
and that proceeding in the wrong direction, or before the spikes are
fully retracted, will result in severe tire damage. Warning signs and/or
traffic signals should always be used in any traffic control application
utilizing traffic control spikes. The warning sign and traffic signals use
LED lamps for energy efficient operation.
PRODUCT PACKAGING : per piece
Features:
Warning Signs
 Light sensor for automatic operation.
 Energy efficient LED bulbs.
 Built-in LED flood lamp for spike illumination.
 Keyed on/off override switch.
Traffic Signal
 Red / green signal operates in sync with operator.
 8-inch lenses.
 Energy efficient LED bulbs.
Specifications:
Warning Signs
 Illuminated with two (2) LED 20 Watt, 700 lumen bulbs.
 LED 9 Watt, 655 lumen flood lamp for spike illumination.
 115 VAC.
 ETL Listed.
 Dimensions: 24"H x 24"W x 8"D.
 Designed to be mounted on 3" mounting pipe (not included).

Traffic Signal
 LED 10 Watt, 1300 lumen traffic lamps.
 12 VDC
 UL Listed.
 Dimensions: 21"H x 9.75"W x 14"D.
 Designed to be mounted on mounting post (not included).
PRODUCT PREPARATION PROCEDURE:
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
INSTALLATION:
Traffic Light and Mounting Kit
1. Assemble support post
2. Mount support post assembly to operator
3. Wire traffic light to operator
Warning Sign
Floodlight should illuminate spikes.
Floodlight: 150watt max, NOT Included
Mount metal floodlight cage to lighting fixture with 2 nuts and bolts supplied
Mount a floodlight with the supplied weather resistant washer
2 internal LED lamps: replace with 9 watt type T8 LED lamp ONLY.
LED Traffic Light and Mounting Kit
1. Assemble support post
2. Mount support post on OPPOSITE side of Access Door.
3. Wire LED Traffic Light to Operator
WARNING SIGN:
The DKS Warning Sign is typically used with traffic control spikes to warn drivers that a
oneway lane condition exists and that proceeding through the lane in the wrong direction
will result in severe tire damage. The red side of the sign warns drivers to stop, while the
green side warns them not to back up. A gate warning sign is also available: “Moving gate can
cause serious injury or death”. The gate warning sign does not include the flood lamp. With
the built-in light sensor, the signs automatically illuminate at dusk and turns off at dawn.
Mounting
3-1/2" (88.9mm) post (not included)
Power
Operates on 115 VAC
12 Watt T8 LED tube lamp, 700 lumens
9 Watt LED flood lamp, 655 lumens
Features
8" (20.3mm) lenses (red/green)
Includes lens shield
U.L. Listed
Shipping Weight
35 lbs (15.8kg)
Warranty
2 year limited warranty
TRAFFIC SIGNAL:
The DKS Traffic Signal is an ideal accessory for any automated vehicular gate system. The
traffic signal is especially useful for use with barrier gate operators and provides drivers with
a visible indication of when it is safe to proceed through the traffic lane. The signal is
synchronized with the movement of the gate so that the red signal is on at all times and
changes to green only when the gate is open or the barrier arm is up.
Mounting
2" pipe (5.08mm)
Power
Operates on 115 VAC
10 watt LED bulbs, 1300 lumens
Features
8" (20.3mm) lenses (red/green)
Includes lens shield
U.L. Listed
Shipping Weight
25 lbs (11.3kg)
Warranty
2 year limited warranty
REFERENCE: 1610 Warning Signs & Traffic Signal - Traffic Control – DoorKing, Inc. - Sweets
(construction.com)

DIVISION 11 – Equipment
PRODUCT DESCRIPTION: The Model 1601 is for high usage
single-lane vehicular traffic control. Typical applications include
commercial, industrial, gated communities and apartment
complexes.
The 1601 operator is designed for single lane (14 ft. max)
vehicular traffic control in high traffic commercial and industrial
applications. The 1601 operator is designed so that it can be
mounted on either the left or right-hand side of the roadway
and is available in white or gunmetal gray finish. The operator
can be equipped with a DC convenience open package
(optional) that will automatically raise the arm in the event of a power outage.

SECTION INCLUDES
A. Parking gates and operators.
1. DoorKing Model 1601.
B. Electric gate operators.
C. Sensors and controls.
RELATED SECTIONS
D. Section 02820 – Fences and Gates: Adjoining fences and gates.
E. Section 02829 – Electric Gate Operators
F. Section 03300 – Cast-in-Place Concrete: Concrete mounting pads.
G. Division 16 – Requirements for electrical connections.
REFERENCES
H. Underwriters Laboratories (UL): UL 325 – Standard for Safety for Door, Drapery,
Gate, Louver, and Window Operators and Systems.
I. Canadian Standards Association (CSA): CSA C22.2 No. 247.
J. Underwriters Laboratories (UL): UL 991 – Standard for Tests for Safety Related
Controls Employing Solid-State Devices.
K. American Society Testing Materials (ASTM): ASTM F2200 – Standard Specification
for Automated Vehicular Gate Construction.
L. National Electrical Manufacturers Association (NEMA): NEMA ICS 6 – Industrial
 Control Systems: Enclosures.
SUBMITTALS
M. Submit under provisions of Section 01 30 00 – Administrative Requirements.
N. Product Data: Manufacturers data sheets on each product to be used, including:
1. Preparation instructions and recommendations.
2. Storage and handling requirements.
3. Installation methods.
O. Shop Drawings: Submit shop drawings showing layout, profiles, and product
components, including anchorage, edge connections, and accessories.
1. Operation, installation, and maintenance manuals including wire diagrams.
2. Risers, layouts, and special wiring diagrams showing any changes to
standard drawings.
DELIVERY, STORAGE, AND HANDLING
P. Deliver, store, and handle materials and products in strict compliance with
manufacturer’s instructions and industry standards.
Q. Store products indoors in manufacturer’s original containers and packaging with
labels clearly identifying product name and manufacturer. Protect from damage.
QUALITY ASSURANCE
R. Manufacturer Qualifications: Substantial transformation and final assembly shall
occur in the United States of America per Section 1605 of the ARRA-09.
S. Installer Qualifications: Installation performed by factory authorized dealer
contractor specifically trained in gate operator systems of the type found within
this section.
1. Provide documentation of maintenance and repair service availability for
emergency conditions.
2. Provide quarterly maintenance for one year following Substantial
Completion of the Project.
WARRANTY
T. Manufacturers standard five (5) year warranty.

MANUFACTURERS
U. Acceptable Manufacturer: DoorKing, Inc.; 120 S. Glasgow Ave; Inglewood, CA
90301; Toll-Free Tel: 800-826-7493; Tel: 310-645-0023; Fax: 310-641-1586; Email:
[email protected]; Web: doorking.com.
V. Substitutions: Not permitted.
W. Requests for substitutions will be considered in accordance with provisions of
Section 01 60 00 – Product Requirements.
PARKING/BARRIER GATE OPERATORS
X. Microprocessor based solid-state control board interacting with card readers, RF
transmitters, access control systems, ticket machines, other activating devices as
required, external devices for pedestrian sensing (photo-eyes) and vehicle (loop)
sensing systems. Control board shall include built-in down timer (1-25 seconds),
built-in ports for two (2) plug-in loop detectors, Up input memory buffer, down
command options, programming switches to set various operating modes, PAMS
sequencing inputs (Perimeter Access Management System), inherent current
sensing reverse system.
1. Compliance: Compliant to UL 325, UL 991 and CSA C22.2 No. 247 and listed
by Intertek Testing Laboratories NA, Inc. (ETL), a Nationally Recognized
Testing Laboratory.
a. This model is intended for use in Class II, III and IV vehicular barrier
gate applications.
2. Warranty: Five (5) year manufacturer’s standard warranty.
3. Operator speed: 90-degrees in approximately 1.5 seconds.
4. Enclosure: 12 gage, 0.105 inch (2.6 mm) G90 hot-dipped galvanized steel,
powder coated, full gloss smooth super TGIC, polyester white.
5. Configuration: Left or right hand mount. In the event of an obstruction
close by the barrier gate, operator can be reversed to allow access to
cabinet door.
6. Motor: 1/2 HP, continuous duty.
7. Gear Reduction: 60:1 worm gear running in a continuous oil bath with 360-
degrees of gear travel.
8. Magnetic Limit Switches: No mechanical switches to wear out or break.
9. Operating Switches: Built-in power (on-off) and operating (up-down-
normal) toggle switches.
10. Convenience Outlets: Two (2) 115 VAC for accessory transformers.
11. Electrical Power Requirements: 115/208/230/460/575 VAC.
a. 208/230/460/575 VAC requires DoorKing High Voltage Kit, P/N 2600-
266.
12. Gate Arms: Fully retroreflectorized on both sides, vertical stripes alternately
red and white at 16-inch intervals as required by the Manual on Uniform
Traffic Control Devices (MUTCD).
a. 14-foot, 3 x 2.185-inch aluminum octagonal.
b. 14-foot, 3 x 2.185-inch aluminum octagonal with contact reverse
edge.
c. 14-foot, 3 x 2.185-inch aluminum octagonal with contact reverse
edge + Red/Green LED light strip (Red when arm is down, Green
when arm is up).
d. 14-foot, 3-inch round aluminum.
e. 14-foot, 3-inch round aluminum with LED light strip.
f. 14-foot, 1x3 kiln dried wood.
g. 12-foot, PVC plastic.
13. Pedestrian Protection
a. Photo-electric eye / auxiliary loop detector relay switch.
1) Requires DoorKing 9411 loop detector used in conjunction with
photo-eye.
14. Accessories: Provide the optional accessories listed below.
a. Arm Breakaway Kit – aluminum arms only.
b. Folding arm kit for low ceiling applications.
 c. LED Lighted folding arm kit for low ceiling applications.
d. Traffic signal and mount kit.
e. Thermostatically controlled fan kit.
f. Thermostatically controlled heater kit.
g. Plug-in loop detectors.
h. Electric reversing edge – reverses rotation of arm on contact with an
obstruction.
i. Gate Tracker Expansion – provides time and date stamped electronic
record of cycles, input errors, loop detector input errors, obstruction
hits and power cycles.
1) Requires companion DoorKing 1830 Series access controller.
j. Backup power inverter – allows system to remain operation upon loss
of primary (AC) power.

PRODUCT APPLICATION/INSTALLATION PROCEDURE:

3.1 INSTALLATION
A. It is preferred, but not required, that this product be installed by a qualified
technician who is certified by either the Accreditation and Certification Institute (ACI) or the
Institute of Door Dealer Education and Accreditation (IDEA).
B. Model 1601 shall be mounted, firmly secured, plumb and level, as required.
C. Wiring shall be uniform and in accordance with national electric codes and
manufacturer’s instructions.
D. All splices shall be in easily accessible junction boxes or on terminal boards.
E. All cable runs in all junction boxes shall be tagged and identified.
F. Coordinate all work with other effected trades and contractors.

3.2 SYSTEM INITIALIZING AND PROGRAMMING

A. System shall be turned on and adjustment made to meet requirements of
specifications and on-site conditions.
B. System shall function as specified.

3.3 SYSTEM TEST PROCEDURES

A. System shall be completely tested to assure that all components and accessories are
hooked-up and in working order.
B. System shall be pre-tested by contractor and certified to function in accordance with
plans and specifications.
C. System shall be tested in presence of owner's representative.

3.4 OWNER INSTRUCTIONS

A. Installation contractor shall conduct up to (1) hour of instruction in use and operation
of the system to designated owner representatives, within (30) days of acceptance.
B. Installation contractor shall conduct up to (1) hour of technical training, in
troubleshooting and service of the system, to designated owner representatives within (90)
days of system acceptance.
3.5 MANUALS AND DRAWINGS
A. Contractor shall provide owner with (2) copies of standard factory prepared
operation, installation and maintenance manuals. Manuals shall include typical wiring
diagrams.
B. Contractor shall provide owner with (2) copies of any risers, layouts, and special
wiring diagrams showing any changes to standard drawings, if required on project.

3.6 MAINTENANCE
A. The manufacturer recommends periodic maintenance at three month intervals as
described in the installation and maintenance manual.
B. External reversing devices should be checked at least once a month.

REFERENCE: 1601 Barrier Gate - Traffic Control – DoorKing, Inc. - Sweets (construction.com)

DIVISION 12 – Furnishings
Claridge Products - Classic Series Freestanding Wood
Display Case
Classic Series Freestanding Wood Display Case
Wood Display Case
 Solid wood construction
 Case has an inside depth of 15-3/4”
 Cases have 3/16” Tempered glass doors with
flat key tumbler locks
 Three adjustable glass shelves
 Back panel available in Claridge Cork, Fabricork,
or Designer Fabric
Sizes
72″ x 48″ x 18″

Options:
 Laminate back panel in your choice of standard Wilsonart laminates
 For optional light, specify 650 LIGHT ADD and add $412.
How to Specify
1. Company / Manufacturer: Claridge Products
2. Product Name: Classic Series Freestanding Cabinet
3. Size: Select a size option
4. Frame Color: Select a frame option
5. Tack/Bulletin Material: Select a tack/bulletin surface
6. Quantity: Include quantity per product
REFERENCE: Classic Series Freestanding Wood Display Case – Claridge Products - Sweets
(construction.com)

Ketcham - 190BV-SM 24" x 30" Deluxe Series Medicine

Cabinet
Our Deluxe Series medicine cabinets are fabricated from
white baked enamel steel and are available in surface
mounted or recessed models. This series is offered in a
stainless steel framed mirror, polished edge mirror, or a
beveled edge mirror.
PRODUCT PACKAGING: per piece
ADDITIONAL PRODUCT DETAILS:
Mirrors/Doors:
 3/16" first quality plate glass. Doors are mounted
on a full length piano hinge equipped with a
magnetic door catch. Can be inverted for right or left swing installation.
Shelves:
 1/4" adjustable glass shelves mounting on locking adjustable aluminum shelf clips.
Width: 24"
Height: 30"
Depth: 4 1/4"
Installation Type: Surface Mounted
Mirror Style: Beveled Edge
Number of Shelves: 4
Body Material: 20 Gauge White Baked Enamel Steel
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
1. Center your cabinet in desired location on the wall. For secure application, locate the studs
within the wall tomount the cabinet properly. If you cannot locate the studs, you will need to
purchase additional hardware tosecure your cabinet to the wall and/or open the wall to
install additional bracing. (Figure 1)
2. Place the cabinet against the wall and mark screw holes as located on the interior of the
cabinet. Placing a smalllevel on the interior of the cabinet will determine if your marks are
level. (Figure 2)
3. Allow for 1” of clearance on height elevation above any obstructions as illustrated in Figure
1. *Note the doorwill exceed the cabinet body by 1” on top and bottom of most cabinets.
Refer to technical data for exact sizes.
4. Single dor cabinets can be inverted in for right or left hand installation. Locate the hinge to
properly select yourdesired door swing.
5. For drywall/wood stud applications insert wood screws into pre-drilled mounting holes
located on theinterior sides of the cabinet. (Pro-tip do not overtighten with this will wrack
the cabinet) use a level to testthat the cabinet is plumb. (Figure 3)
6. Insert shelf clips at desired height locations and place glass shelf. Do not install shelves
prior tocabinet installation.
NOTICE:
1. Gently close the cabinet door to avoid potential injuries and damage. Damaged glass
should be replaced
right away.
2. The cabinet must be installed onto a solid wall. (Thinner wood siding wall and hollow wall
are not applicable)
Surface Mounted Deluxe Features:
- White Baked Enamel Steel Body
- Full Length Piano Hinge
- Magnetic Door Catch
- Adjustable Glass Shelves
PRODUCT PREPARATION PROCEDURE:
**Professional Installation is recommended to insure proper installation.
**Door removal is recommended, but not required for installation.
**Please do not stand your medicine cabinet on end while unboxing. Lie the cabinet down
mirror side up prior to installation. Set on a clean surface, like a towel or carpet to avoid
damage.
**Prior to discarding the packaging, locate shelves, door hardware, and screws where
applicable

Features:Doors mounted on a continuous full-length piano hinge in a wide array of sizes.

Idealdesign to meet HUD housing and federal specifications.Cabinets can be inverted for right
orleft swing installation.
Specifications:Fabricated with 20 gauge white bakedenamel steel bodies and doors.
Mirrors/Doors:3/16” first quality plate glass. Doors are mounted on a full length piano hinge
equipped with a magnetic door catch.
Shelves:1/4”adjustable glass shelves mounting on locking adjustable aluminum shelf clips
REFERENCE: 190BV-SM 24" x 30" Deluxe Series Medicine Cabinet – Ketcham - Sweets
(construction.com)
DIVISION 13 – Special Construction
PRODUCT DESCRIPTION:
Aston Global - HT635 3-Person Hot Tub Wedge Corner Unit
with 7 Jets
Your personal invitation to a hydrotherapy oasis, the HT635 3-
person dual-insulated hot tub in Prism White acrylic and
Redwood cabinatry is the idea choice for the smaller space.
Features:
 3-Person Hot Tub
 Prism White Quartzite Acrylic w/ Multi-Layered
Fiberglass Reinforcement
 Jets: 7, Grey
 Unique, Wedge Corder Design
 User Friendly Digital Topside Control
 Balboa Controller
  Pump: 1.0 cHP (Continuous Horsepower)2 Speed
 All Weather Maintenance-Free Redwood Cabinet
 Insulation: Thermal Wrapped Insulated Cabinet Panels
 Ozone Ready (Ozonator Not Installed)
 Heavy Duty Frame - Welded Steel Frame with Wood Uprights
 Removable Panels: 6
 Electrical Requirements - 110V/15 Amp Dedicated Service, GFCI Breaker Required
 Cover: Marine Grade 4"-2" Tapered UV Resistant Vinyl Cover Included (Color Matches
Cabinet Color)
Dimensions:
 Exterior Dimensions: 69” L x 56” W x 30” H
 Interior Dimensions: 71.6" L x 45.6" W x 27.5" H

PRODUCT DESCRIPTION:
Natare Corporation - Natatec® PVC Pool Lining
PVC Membrane Pool Lining Systems
Colorful, durable, watertight swimming pool lining
systems.
Natatec® is a flexible blanket of PVC with a strong inner
core of polyester mesh fabric specifically designed for
commercial pool applications.
Features & Benefits

 Custom-fit and tailored on-site to ensure an

attractive, watertight pool surface
 Fast, efficient construction, suitable for all climates and weather extremes
 Resists algae, mold and mildew
 Long-lasting and durable
 Saves on water, chemicals and heat
Perfect for Renovation & New Construction
Natatec PVC pool lining membranes dramatically reduce construction and renovation costs,
limit maintenance and greatly extend the lifespan of your pool facility.
Natatec provides a means to renovate pools in the worst condition. The pool lining
membrane spans cracks, joints and other defects with its tough, flexible blanket.
The Natatec system eliminates costly and time-consuming annual surface maintenance.
Sandblasting, chipping, patching, caulking and recoating are simply not needed. Our
membrane provides an attractive, flexible and watertight pool lining inside virtually any
supporting structure.
Features & Benefits of Natatec Pool Lining Systems
Ease of Installation
Our installation system allows for a tailored fit for in-ground, on-ground or elevated
swimming pools. Previously difficult installations and renovations are made possible. Unlike
conventional coatings, Natatec membranes can be installed in almost any weather. The
drastic reduction of downtime for installation makes it possible to renovate your pool facility
in record time.
Fiberglass Pool Repair
Natatec is the solution for repairing fiberglass failure in swimming pools. Fiberglass pool
coatings are notorious for cracking and removing failing fiberglass material in pools can be
expensive. For a fraction of the cost, Natatec can be installed directly over the existing
fiberglass surface to create a new worry-free surface. The pool lining material is cut-to-fit and
welded on-site to ensure a pool coating that is completely watertight, attractive and long-
lasting.
Clean, Safe and Sanitary
The smooth, non-porous surface of Natatec membranes helps prevent the growth of bacteria
and algae and makes pool cleaning easy and inexpensive. With our pool lining system, harsh
acid washing and other chemicals are not necessary to clean your pool. The neutral PVC
surface does not alter water chemistry like plaster, grout, concrete and other porous
surfaces, providing ongoing savings in operational costs. By creating a watertight lining, our
membranes reduce water lost through leakage and save energy and chemical use.
Eye-Catching Colors
Create a beautiful pool that has an amazingly long life with Sky Blue, Caribbean Blue and
White. A special Black material is available for racing lanes, targets, custom logos and other
pool details. Each color can be shaped, cut and custom-designed to fit your special needs.
Custom colors and patterns can also be created to meet the unique look of your facility.
PRODUCT PREPARATION PROCEDURE:
rectangular sheets or cut-to-fit sections. Other standard sizes include: 2” x 2” by 10’ twenty
gauge galvanized or stainless steel angle, and 6” x 10’ twenty gauge galvanized or stainless
steel sections. Special configurations of both galvanized or stainless steel and PVC coated
steel are available.
PRODUCT APPLICATION/INSTALLATION PROCEDURE:
1. Clean the surface and walls
2. Apply adhesive and fleece to the walls
3. Tack the weld liner panels onto walls
4. Apply compression strip around the perimeter of the pool walls on top of liner
5. Screw compression strip to walls to create a watertight seal
6. Weld liner to walls and floor
7. Weld target and inspect all seems
Description:
Natatec ND is a heavy duty, flexible PVC material with a tough inner core of polyester
supporting scrim, which combines UV stabilized PVC, premium coloration and highly durable
plasticizers with a polyester supporting scrim. A durable, high damage-resistant lining
material, Natatec ND includes special antimicrobial agents to resist microbial attack and
staining. A topical coating of acrylic varnish is applied during the manufacturing process to
provide additional protection against U.V. rays, stains, scratches, and biodegeneration.
Natatec ND is available in a 60-mil fabric reinforced thickness.
Application and uses: Natatec ND is typically used for new construction or renovation of
public, commercial and institutional swimming pool and aquatic facilities. A wide variety of
installation techniques are available to provide maximum design flexibility and membrane to
result in a flexible and durable lining system.
Advantages: Highly flexible, easily fabricated and UV-resistant. Excellent weathering. Quick
installation. Absolutely waterproof. Chemically resistant. Economical and cost efficient. PVC
formulations allow positive heat-welded seams. Reinforced construction.
Colors: Typically light blue, dark blue or white with other colors available.
Standard Sizes: Typically 75 in. x 82 ft. roll (512.6 ft²) / 1.905 x 25 M (47.63 m²). Other roll
widths available.
REFERENCE: Natatec® PVC Pool Lining – Natare Corporation - Sweets (construction.com)
DIVISION 14 – Conveying Equipment
Hydraulic Home Elevator
When it comes to residential elevator systems, hydraulic
drives are a popular choice for homeowners looking for
quality, safety, and the ‘quietest’ ride.
When it comes to residential elevator systems, hydraulic
drives are a popular choice for homeowners looking for
quality, safety, and the ‘quietest’ ride.
Hydraulic home elevator systems utilize a ram or piston to
raise and lower the car by filling or releasing fluid into an
airtight cylinder. With more standard features and custom
options than any other elevator on the market today,
Symmetry’s Hydraulic Drive Residential Elevator system is
the industry leader.
Unique in the market, no other company offers emergency battery-operated lowering, COP
and hall stations digital position indicators, custom wood sills and energy-efficient LED
lighting as standard features.
This drive system accommodates up to six stops, 50’0" of travel and is equipped to hold up to
1,000 pounds.

Standard Features

 Travel: Maximum of 50’0" (minimum 12” between stops)

 Speed: 40 feet per minute
 Rated Capacity: 1000 pounds
 Overhead Minimum of 7’10" (94”) with remote controller*
 Pit depth: 6” minimum (8” preferred)
 Two stops
 Single opening
 Three-year limited parts warranty

Mechanical Equipment

 Modular 6-1/4 pound T-rail structure

 Car frame assembly
  208/230 volts alternating current, 60 hertz, 30 amp single phase power supply for
motor controller
 120 volts alternating current, 60 hertz, 15 amp single phase power supply for lighting
 208/230, 3 horsepower submersed motor with 2-speed valve assembly (1750
revolutions per minute / 17 full-load-amperage) - manual down valve for emergency
lowering
 Screw pump (300 micron screen)
 Positive pressure switch
 Code compliant electrical disconnects included*

Safety Features

 Slack rope safety device

 Motor controller supply disconnects (located in controller)
 Car light supply disconnects (located in controller)
 Rupture Valve (Type “C” Safety)
 Pit stop switch
 Car top stop switch
 In-car emergency stop switch and alarm
 Safety switch for car gate(s)
 Battery back-up emergency car lights and alarm
 Electromechanical hoistway door interlocks (doors by others)
 Light curtain monitoring the car entrance

Controls

 Programmable Logic Controller (PLC)

 Non-selective collective automatic operation
 S.M.A.R.T. System (Self-Monitoring Alert Response Technology)*
 Car Operating Panel (COP) with LED floor position indicator; available in multiple
finishes
 Recessed phone box in multiple finishes (phone jack included)
 Hall stations with call button and LED floor position indicator; available in multiple
finishes
 Automatic car lighting
 Single floor designated car homing
 Uninterruptible Power Supply (UPS) for car lowering and automatic gate operation (if
provided) in the event of power failure*

Car Features

 Car size up to 15 square feet

 7’0” interior car height
  Birch, Oak, or Maple flat veneer interior walls with matching ceiling*
 Matching wood handrail
 Matching wood car sill*
 Unfinished plywood floor with sill set for .75” (flooring by others)
 2 energy saving recessed LED lights with black trim rings*
 7’0” vinyl laminate accordion gate (light oak, dark oak, birch, white, chalk or antique
white)

Optional Features

 Up to six stops
 Single automatic push button operation
 Custom car size up to 18 square feet**
 Custom car heights
 Shaker or Recessed panel car with flush ceiling
 Shaker or Recessed panel car with matching ceiling
 Raised panel car with matching ceiling
 4 recessed LED lights with black, brass, nickel or bronze trim rings*
 Factory finished car
 Polished stainless steel, polished or brushed brass, black, vintage bronze and oil
rubbed brass fixtures (including COP, phone box, hall calls, and handrail)
 COP with integrated keypad phone*
 Custom wood interiors
 Custom factory finishes (antiqued, distressed, & crackle)*
 Green material alternatives and finishes for car interiors*
 Symmetry Safety 3 Panel Car Door
 Two & Three speed car or car and landing doors
 Wrap around car door
 Enterprise collapsible gate
 Hardwood veneer accordion gate
 Clear panel accordion gate
 Automatic car gate/door operator (not available on Enterprise collapsible gate)
 .75” finished or unfinished factory installed
hardwood car flooring
 Factory flooring insert for 1/4” flooring by others
 Buffer springs (requires minimum of 10” pit
depth)
 Key switch for COP and hall stations
 750 pound car capacity
 Accordion gates will have bronze hardware except
on white, chalk, or antique white gates. Acrylic
gates will have clear hardware when stainless or
black fixtures are provided.
Symmetry Elevating Solutions - Vertical Platform Lift - Enclosed Lift Plexi-glass
Vertical Platform Lift - Enclosed Lift Plexi-glass
The enclosed plexi-glass vertical platform lifts are used in the same way as the enclosed lift,
with plexi-glass infill enclosure wall panels.
Standard Features

 750 to 1,000-pound capacity

 Speed: 10 feet per minute
 Motor: 1 horsepower, 115 volt (Acme Screw Drive)
 Lifting height: up to 60” for commercial applications and 168" for residential
applications
 Steel construction with electrostatic, powder-coated finish
 A.W.A.R.E. system (Active Wiring, Accessories, Relay, and Electronics Diagnosis)*
 Constant-pressure up/down control switch installed on the platform
 Constant-pressure elevator-style hall call control station provided at each landing

Drive Options

 Acme Screw Drive: 10 feet per minute, 1 horsepower, 115 volt

 Accelerated Acme Screw Drive: 20 feet per minute, 1 horsepower, 115 volt
 Hydraulic Drive: 17-20 feet per minute, 2 horsepower, 115 volt

Optional Features

 Low profile Carriage: 1 1/2" pit depth*

 Remote mounted controller*
 230 volt motor
 ADA phone for both indoor and outdoor models
 Emergency lights
 Key switch to lock platform and landing controls
 Stationary ramp
 Full-speed battery backup
 Power gate operators*
 Power ventilation system
 Slant roof/dome enclosure

Safety Features

 Non-skid platform surface (black)

 Obstruction safety panel under platform (when not installed with a runway enclosure)
 Alarm and emergency stop switch
 Grab rail
  Landing interlocks keep door closed/locked when the platform is at another landing
 Upper final limit switch

Clear Platform Sizes

 36”W x 48”D
 36”W x 54”D
 36”W x 60”D
 42”W x 60”D
 Custom sizes available

Enter/Exit Configurations

 Straight-through
 90° adjacent
 Same side

Gate/Door Options

 42” platform gate**

 42” landing gate**
 80” landing gate**
 Non-fire-rated red oak door‡
 Fire-rated steel door

Enclosure Options

 Metal Infill enclosure wall panels

 Plexi-glass infill enclosure wall panels
PART 1 GENERAL
1.01 SECTION INCLUDES:
A. UL – Unenclosed.
B. SL – Shaftway.
C. EL – Enclosed.
D. Hybrid (Elevator Style Lift).
1.02 RELATED SECTIONS:
A. Section 00330 - Cast–in-Place Concrete: Concrete shaftway and anchor placement.
B. Section 04800 - Masonry Assemblies: Masonry shaftway and anchor placement.
C. Section 06100 - Rough Carpentry: Blocking in framed construction for lift attachment.
D. Section 09260 - Gypsum Board Assemblies: Gypsum shaft walls.
E. Division 16 – Electrical: Dedicated telephone service and wiring connections.
F. Division 16 – Electrical: Lighting and wiring connections at top of shaft.
G. Division 16 – Electrical: Electrical power service and wiring connections.
1.03 REFERENCES:
A. This lift shall be designed and tested in accordance with ICC/A117.1, NEC and ASME
A18.1 Guidelines.
B. All designs, clearances, construction, workmanship and installation shall be in
accordance with the requirements and code adopted by the authority having jurisdiction.
C. This platform lift shall be subject to local, city and state approval prior to and
following installation.
1.04 SUBMITTALS:
A. Submit under provisions of Section 01300.
B. Product Information:
1. Submit manufacturer’s installation instructions including preparation and equipment
handling requirements.
2. Show maximum and average power necessity.
C. Drawings shall include:
1. Typical details of assembly, erection and anchorage.
2. Wiring diagrams for power, control, and signal systems.
3. Complete layout with location of equipment.
D. Manufacturer’s Certificates must certify products meet or exceed specified
requirements.
1.05 QUALITY ASSURANCE:
A. Manufacturer: Company shall contain personnel with not less than ten (10) years of
experience in the design and fabrication of vertical wheelchair lifts.
B. Technical Services: Manufacturer and authorized dealer shall work with architects,
engineers and contractors to adapt the vertical wheelchair lift to the design and structural
requirements of the building, site, and code requirements.
C. Unit must be assembled and tested in factory before shipment. Vertical Wheelchair
Lift equipment shall meet or exceed the National and Local standards.
D. All load ratings and safety factors shall meet or exceed those specified by all
governing agencies with jurisdiction and shall be certified by a professional engineer.
E. Installer Qualifications: Factory trained and licensed to install equipment of this
scope, with evidence of experience with specified equipment. Installing company shall have
qualified people available to ensure fulfillment of maintenance and callback service.
1.06 REGULATORY REQUIREMENTS
A. Provide Vertical Wheelchair Lift complying with:
1. ASME A18.1 – Safety Code for Platform Lifts
2. ASME A17.1 – Safety Code for Elevators and Escalators
3. ASME A17.5 – Elevator and Escalator Electrical Equipment
1.07 DELIVERY, STORAGE, AND HANDLING:
A. Products stored in manufacturer’s unopened packaging until ready for installation.
B. Components stored off the ground in a dry covered space, protected from weather
conditions.
1.08 PROJECT CONDITIONS:
A. Vertical Wheelchair Lift not to be used for hoisting materials or personnel during
construction.
1.09 WARRANTY:
A. Unit shall have a FOUR (4) year limited parts warranty covering replacement of
defective parts of the basic unit, including all electrical and drive system components, at no
cost. Labor costs required to replace parts is not included. Preventative maintenance
agreement required.
B. Extended Warranty: Provide an extended manufacturer’s warranty covering the
vertical wheelchair lift components for the following additional period beyond the initial
standard four year warranty. Preventative Maintenance every six (6) months required.
1. 3 years (7 years total).
2. 6 years (10 years total).
3. Lifetime.
1.10 MAINTENANCE
A. Maintenance of the vertical wheelchair lift unit shall consist of regular cleaning,
inspection, and adjustment of the unit at intervals not longer than every six (6) months. Rule
10.2.1 of ASME A18.1 required all Vertical Wheelchair Lifts to be inspected every six (6)
months. Provide maintenance contract for the following years:
1. 4 years.
2. 7 years.
3. 10 years.
4. Lifetime.
PART 2 PRODUCT
2.01 MANUFACTURER:
A. Acceptable Manufacturer: Symmetry Elevating Solutions
Email: [email protected]
Toll Free: 877-568-5804
Website: www.symmetryelevators.com
B. U.S. OWNED AND OPERATED: Manufacturer must registered U.S. owned company
and manufacturing operation located in the United States of America – America Owned,
American Operated.
C. No Substitutions Allowed.
D. Request for substitutions will be considered in accordance with provisions of section
01600.

2.02 UNENCLOSED VERTICAL WHEELCHAIR LIFT:

A. General Description: The Unenclosed vertical platform lift is designed for lifting
heights up to 60”. Versatile enough for indoor or outdoor use, this unit can either be
mounted directly to the floor or in a shallow pit.
B. Capacity:
1. 750 lbs.
C. Lifting Height
1. Up to 42 inches.
2. Up to 60 inches.
3. Up to 72 inches (Residential Application only).
4. Up to 96 inches (Residential Application only).
5. Up to 120 inches (Residential Application only).
6. Up to 144 inches (Residential Application only).
7. Up to 168 inches (Residential Application only).
D. Platform Size:
1. 36” W x 48” D
2. 36” W x 54” D
3. 36” W x 60” D
4. 38” W x 54” D
5. 42” W x 60” D
6. Custom Size _____ W x _____ D
E. Platform Configuration:
1. Straight Through.
2. Enter/Exit same side.
3. 90 Degree.
F. Gate/Door:
1. Gate Height: 42 inches.
2. Platform Gate: Travels with platform and opens at lower landing.
3. Upper Landing Gate: Detached, freestanding type.
G. Landing Openings:
1. Lower Landing: Door.
2. Lower Landing: Gate.
3. Upper Landing: Door.
4. Upper Landing: Gate.
H. Door Construction:
1. 42 inch tall Landing/Platform Gate.
2. 80 inch tall gate.
a. Lower Landing
b. Upper Landing
3. A CSD-Rated (R) Fire Rated (B Label) flush mounted steel door and frame shall be
provided. Door shall include wire mesh vision panel with delay action door closure, dead
latch, dummy trim door handle and electric strike.
4. A CSD – Non-Rated (NR) Low profile flush mounted steel door and frame shall be
provided. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
a. Panels of 16 gauge galvanized steel.
b. Panels of clear Plexiglas.
c. Panels of bronze Plexiglas.
d. Panels of ¼ inch laminated safety glass.
5. A CWS – Flush mounted, solid core oak laminated door and (oak) frame shall be
proved. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
6. Flush mounted, 42 inches high, solid core oak laminated gate and (oak) frame shall be
provided at the upper landing. Gate includes spring hinges, dead latch, dummy trim gate
handle, lock plate cover and electric strike.
I. Power Gate Operators:
1. Location:
a. Platform Gate.
b. Upper landing Gate.
2. “Smart Operation” Power Gate Operator: Allows operator to open, stop at
obstruction, close and remain in NORMAL operation mode. Operator will not stop mid cycle
and leave unit non-operational.
3. Opens automatically when platform arrives at landing, pressing the call button, or
pulling on the gate.
4. ADA compliant.
5. Low voltage, 24 VDC.
J. Screw Drive:
1. Drive Type: Acme Screw Drive.
2. Travel speed: 10 fpm.
3. Motor: 1HP, 115 volt, 1 phase.
4. Power Supply:
a. 115 VAC, 30 Amp, Single Phase.
b. 230 VAC, 15 Amp, Single Phase.
5. Battery Powered Emergency Lowering:
a. Battery powered platform lowering device which automatically activates in the event
of power failure.
b. Capable of running lift up and down for a minimum of 5 trips with rated load.
6. The drive mechanism shall be a stationary nut on a rotating 1” diameter Acme screw
with a secondary safety nut.
K. Hydraulic Drive:
1. Drive Type: Chain Hydraulic.
2. Travel speed: 17 to 20 fpm.
3. Motor: 2HP, 24 VDC. AC powered primary drive.
1. Power Supply: 115 VAC, 15 Amp, Single Phase
a. Powered by continuous building mains converted to 24 VDC equipped with auxiliary
battery power system. Battery power system capable of running lift up and down for a
minimum of 5 trips with rated load.
4. Standard on board 24 VDC standby battery power to operate the lift up and down in
the event of a power failure.
5. Drive mechanism shall be a 1:2 #60 roller chains hydraulic equipped with a type “A”
instantaneous slack chain safety device.
6. Hydraulic connections shall be metal and have rated pressure that withstands the
working pressure with a 5 times safety factor.
7. Bi-directional leveling, factory supplied oil collection means as required by A18.1-
8.1.4.7, Angled pressure gage standard, roller bearing sprockets, vibration isolated hydraulic
power unit.
L. Lift Components:
1. Symmetry Elevating solutions PLC Controller with self diagnostics and digital display.
A.W.A.R.E. System (Active Wiring, Accessories, Relay & Electronics Diagnosis System)
generates on-demand diagnostic codes identifying trouble or maintenance codes.
2. The Drive Tower support shall be a combination 7 gauge C Channel, 7 gauge interface
plates and 16 gauge exterior skin.
3. Platform shall be constructed of 12-gauge minimum hot rolled steel. If unit is not
installed in a 3-inch pit, an auto-retracting ramp, or stationary ramp, shall be provided that
extends to meet lower landing.
4. Platform side panels shall be 42” high, Side panel framework shall be a minimum of
1”x1 ½” steel. Solid infill panels shall be a minimum of 18 gauge steel.
5. Carriage platform supports shall be a minimum of ½” steel. Solid infill panels shall be
a minimum of 18 gauge steel.
6. Elevator style (Nylon) rollers shall be used for axial carriage guidance and wear pads
shall be used for horizontal stability.
7. Loaded fasteners shall be grade eight or higher. Locking fasteners shall be used in all
critical locations.
8. Outdoor Protection: Lift shall include modifications recommended by manufacturer
for reliable performance in extreme outdoor environment.
M. Platform Base & Frame Installation:
1. Pit Mount: (recess application) Level pit floor slab recessed min. 3” by others as
outlined on site specific show drawings. This application does not require ramp and allows for
smooth transition from landing into lifting equipment.
2. Floor Mount: (non-recess application) If unit is not installed in a min. 3” pit, an auto-
retracting ramp shall be provided that extends to meet the lower landing. Optional fixed
mounted ramp is available. (verify clear landing requirements if fixed ramp selected)
a. Platform Access Ramp: 12 gauge galvanized steel plates; slip resistant surfaces.
1. Ramp: Stationary type.
2. Ramp: Automatic folding type.
3. Carriage to be equipped standard with articulating base and carriage design, which
allows the carriage to be folded to reduce the tower and carriage width to 21” for ease of
installation, without removal of the carriage.
N. Platform Controls:
1. Constant pressure up/down control switches shall be installed on the platform. All
switches meet IP66 requirements.
2. An illuminated emergency stop switch / Audible alarm switch shall be provided on the
car as a means of signaling for assistance in the event of an emergency.
3. Keyless operation.
4. Keyed operation.
5. Emergency Telephone:
a. Wiring Only.
b. Platform shall be equipped with a telephone meeting the following requirements:
1. ADA compliant.
2. Shall be operational in the event of power failure.
3. Specified under Division 16 a telephone line shall be supplied to the lift.
O. Call Station Controls:
1. Constant pressure up/down control switch installed on the platform.
2. Constant pressure, elevator-style, hall call control stations provided at each landing.
3. Keyless operation.
4. Keyed operation.
5. Call Station Mounting:
a. Lower:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
b. Upper:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
P. Safety Features/Devices:
1. Grounded electrical system with upper, lower, and final limit switches.
2. Safety Pan (Required).
3. Obstruction Panel, preventing unit from moving downward when an obstruction is
encountered.
4. A grab rail shall be provided on the platform.
5. A gate with a min. height of 42” and a combination mechanical lock with an electric
contact shall be provided at the upper landing, lock must be engaged for lift to move from
landing.
6. At all landings an electromechanical interlock shall be used to keep doors closed when
lift is on another floor.
7. Electrical disconnect which will shut off power to the lift.
8. Pit stop switch mounted on Drive Tower.
Q. Finishes:
1. Finish shall be powder coating, oven baked.
2. Color:
a. Ivory.
b. White.
c. Black.
d. Grey.
e. A selection from 213 RAL colors.
2.03 SHAFTWAY VERTICAL WHEELCHAIR LIFT:
A. General Description: The Shaftway vertical platform lift (wheelchair lift) is installed in
a shaftway or hoistway built by others. The lift platform and drive tower are located within
the shaftway, while each landing consists of a door or gate, integral to the operation of the
lift. At the uppermost landing, the shaftway can extend all the way to the ceiling or to a
minimum of 42” beyond the upper landing, for a more “open” application.
B. Capacity:
1. 750 lbs.
C. Lifting Height
1. Up to 42 inches.
2. Up to 60 inches.
3. Up to 72 inches.
4. Up to 96 inches.
5. Up to 120 inches.
6. Up to 144 inches.
7. Up to 168 inches.
D. Platform Size:
1. 36” W x 48” D
2. 36” W x 54” D
3. 36” W x 60” D
4. 38” W x 54” D
5. 42” W x 60” D
E. Platform Configuration:
1. Straight Through.
2. Enter/Exit same side.
3. 90 Degree.
F. Gate/Door:
1. Gate Height: 42 inches.
2. Upper Landing Gate: Detached, freestanding type.
G. Landing Openings:
1. Lower Landing: Door.
2. Intermediate Landing: Door.
3. Upper Landing: Door.
4. Upper Landing: Gate.
H. Door Construction:
1. A CSD-Rated (R) Fire Rated (B Label) flush mounted steel door and frame shall be
provided. Door shall include wire mesh vision panel with delay action door closure, dead
latch, dummy trim door handle and electric strike.
2. A CSD – Non-Rated (NR) Low profile flush mounted steel door and frame shall be
provided. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
a. Panels of 16 gauge galvanized steel.
b. Panels of clear Plexiglas.
c. Panels of bronze Plexiglas.
d. Panels of ¼ inch laminated safety glass.
3. A CWS – Flush mounted, solid core oak laminated door and (oak) frame shall be
proved. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
4. Flush mounted, 42 inches high, solid core oak laminated gate and (oak) frame shall be
provided at the upper landing. Gate includes spring hinges, dead latch, dummy trim gate
handle, lock plate cover and electric strike.
I. Upper Landing Gate Construction:
1. A minimum 42 inch high gate with combination mechanical lock and electrical
contact, pre-hung on a steel tubular frame. Gate hinges designed to auto close. Gate
framework to be 1” x 1 ½” steel with 16g solid infill steel panel. Optional mid mount gate
operator can be designed and integrated into gate design.
a. Panels of 16 gauge galvanized steel.
b. Panels of clear Plexiglas.
J. Power Door Operators:
1. Location:
a. Lower Landing: Door.
b. Intermediate Landing: Door.
c. Upper Landing: Door or Gate.
2. “Smart Operation” Power Door Operator: Allows operator to open, stop at
obstruction, close and remain in NORMAL operation mode. Operator will not stop mid cycle
and leave unit non-operational.
3. Opens automatically when platform arrives at landing, pressing the call button, or
pulling on the gate.
4. ADA compliant.
5. Low voltage, 24 VDC.
K. Screw Drive:
1. Drive Type: Acme Screw Drive.
2. Travel speed: 10 fpm.
3. Motor: 1HP, 115 volt, 1 phase.
4. Power Supply:
a. 115 VAC, 30 Amp, Single Phase.
b. 230 VAC, 15 Amp, Single Phase.
5. Battery Powered Emergency Lowering:
a. Battery powered platform lowering device.
b. Automatically activates in the event of power failure.
c. Capable of running lift up and down for a minimum of 5 trips with rated load.
6. The drive mechanism shall be a stationary nut on a rotating 1” diameter Acme screw
with a secondary safety nut.
L. Hydraulic Drive:
1. Drive Type: Chain Hydraulic.
2. Travel speed: 17 to 20 fpm.
3. Motor: 2HP, 24 VDC. AC powered primary drive.
2. Power Supply: 115 VAC, 15 Amp, Single Phase
a. Powered by continuous building mains converted to 24 VDC equipped with auxiliary
battery power system. Battery power system capable of running lift up and down for a
minimum of 5 trips with rated load.
4. Standard on board 24 VDC standby battery power to operate the lift up and down in
the event of a power failure.
5. Drive mechanism shall be a 1:2 #60 roller chains hydraulic equipped with a type “A”
instantaneous slack chain safety device.
6. Hydraulic connections shall be metal and have rated pressure that withstands the
working pressure with a 5 times safety factor.
7. Bi-directional leveling, factory supplied oil collection means as required by A18.1-
8.1.4.7, Angled pressure gage standard, roller bearing sprockets, vibration isolated hydraulic
power unit.
M. Lift Components:
1. Symmetry Elevating solutions PLC Controller with self diagnostics and digital display.
A.W.A.R.E. System (Active Wiring, Accessories, Relay & Electronics Diagnosis System)
generates on-demand diagnostic codes identifying trouble or maintenance codes.
2. The Drive Tower support shall be a combination 7 gauge C Channel, 7 gauge interface
plates and 16 gauge exterior skin.
3. Platform shall be constructed of 12-gauge minimum hot rolled steel. If unit is not
installed in a 3-inch pit, an auto-retracting ramp shall be provided that extends to meet lower
landing.
4. Platform side panels shall be 42” high, Side panel framework shall be a minimum of
1”x1 ½” steel. Solid infill panels shall be a minimum of 18 gauge steel.
5. Carriage platform supports shall be a minimum of ½” steel. Solid infill panels shall be
a minimum of 18 gauge steel.
6. Elevator style (Nylon) rollers shall be used for axial carriage guidance and wear pads
shall be used for horizontal stability.
7. Loaded fasteners shall be grade eight or higher. Locking fasteners shall be used in all
critical locations.
N. Drive Tower Side Wall Panels: Provide panels to cover the front and top of the open
area to the top of the top surface drive tower. Panels shall be 16 gauge galvanized steel,
mounting hardware include.
O. Platform Base & Frame Installation:
1. Pit Mount: (recess application) Level pit floor slab recessed min. 3” by others as
outlined on site specific show drawings. This application does not require ramp and allows for
smooth transition from landing into lifting equipment.
2. Floor Mount: (non-recess application) If unit is not installed in a min. 3” pit, an auto-
retracting ramp shall be provided that extends to meet the lower landing. Optional fixed
mounted ramp is available. (verify clear landing requirements if fixed ramp selected)
a. Platform Access Ramp: 12 gauge galvanized steel plates; slip resistant surfaces.
1. Ramp: Stationary type.
2. Ramp: Automatic folding type.
3. Carriage to be equipped standard with articulating base and carriage design, which
allows the carriage to be folded to reduce the tower and carriage width to 21” for ease of
installation, without removal of the carriage.
P. Platform Controls:
1. Constant pressure up/down control switches shall be installed on the platform. All
switches meet IP66 requirements.
2. An illuminated emergency stop switch / Audible alarm switch shall be provided on the
car as a means of signaling for assistance in the event of an emergency.
3. Keyless operation.
4. Keyed operation.
5. Emergency Telephone:
a. Wiring Only.
b. Platform shall be equipped with a telephone meeting the following requirements:
1. ADA compliant.
2. Shall be operational in the event of power failure.
3. Specified under Division 16 a telephone line shall be supplied to the lift.
Q. Call Station Controls:
1. Constant pressure up/down control switch installed on the platform.
2. Constant pressure, elevator-style, hall call control stations provided at each landing.
3. Keyless operation.
4. Keyed operation.
5. Call Station Mounting:
a. Lower:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
b. Intermediate:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
c. Upper:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
R. Safety Features/Devices:
1. Safety Pan.
2. Grounded electrical system with upper, lower, and final limit switches.
3. When not installed with a runway enclosure, the platform shall be equipped with an
obstruction panel that will stop only the downward travel if an obstruction is encountered.
4. A grab rail shall be provided on the platform.
5. A gate with a min. height of 42” and a combination mechanical lock with an electric
contact shall be provided at the upper landing, lock must be engaged for lift to move from
landing.
6. At all landings an electromechanical interlock shall be used to keep doors closed when
lift is on another floor.
7. Electrical disconnect which will shut off power to the lift.
8. Pit stop switch mounted on mast wall.
S. Finishes:
1. Finish shall be electro statically applied powder coating, oven baked to cure.
2. Color:
a. Ivory.
b. White.
c. Black.
d. Grey.
e. A selection from 213 RAL colors.

2.04 ENCLOSED VERTICAL WHEELCHAIR LIFT:

A. General Description: The Enclosure vertical wheelchair lift travels up and down within
its own, self-contained enclosure. The enclosure can either have an “open” look with a 42”
tall gate and enclosure extension above the upper landing, or be fully enclosed complete
with full-height doors, roof and ventilation system for outdoor applications. In addition to
the drive tower, lift platform, and enclosure, this unit also has landing doors and/or gates
that are fully integrated into the walls themselves.
B. Capacity:
1. 750 lbs.
C. Lifting Height:
1. Up to 42 inches.
2. Up to 60 inches.
3. Up to 72 inches.
4. Up to 96 inches.
5. Up to 120 inches.
6. Up to 144 inches.
7. Up to 168 inches.
D. Platform Size:
1. 36” W x 48” D
2. 36” W x 54” D
3. 36” W x 60” D
4. 42” W x 60” D
5. 42” W x 60” D
E. Platform Configuration:
1. Straight Through.
2. Enter/Exit same side.
3. 90 Degree.
F. Gate/Door:
1. Gate Height: min. 42 inches.
2. Door Height: 80” clear.
3. Platform Gate required on 3” above enclosures.
4. Integrated upper landing gate. 42 inches or 80 inches available.
G. Landing Openings:
1. Lower Landing: Gate.
2. Intermediate Landing: Integrated Lower Landing Gate.
3. Upper Landing: Door.
4. Upper Landing: Gate.
H. Door Construction:
1. A CSD-Rated (R) Fire Rated (B Label) flush mounted steel door and frame shall be
provided. Door shall include wire mesh vision panel with delay action door closure, dead
latch, dummy trim door handle and electric strike.
2. A CSD – Non-Rated (NR) Low profile flush mounted steel door and frame shall be
provided. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
a. Panels of 16 gauge galvanized steel.
b. Panels of clear Plexiglas.
c. Panels of bronze Plexiglas.
d. Panels of ¼ inch laminated safety glass.
3. A CWS – Flush mounted, solid core oak laminated door and (oak) frame shall be
proved. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
4. Flush mounted, 42 inches high, solid core oak laminated gate and (oak) frame shall be
provided at the upper landing. Gate includes spring hinges, dead latch, dummy trim gate
handle, lock plate cover and electric strike.
5. A RDI Interlock with steel housing and cam, integrated into door frame that contains
electric contacts in insure the door is both closed and locked shall be provided. (This option
is required when flush mounted door frames are provided by others).
I. Power Gate Operators:
1. Location:
a. Lower Landing Door.
b. Intermediate Landing Door.
c. Upper landing Door.
d. Upper Landing Gate.
2. “Smart Operation” Power Gate Operator: Allows operator to open, stop at
obstruction, close and remain in NORMAL operation mode. Operator will not stop mid cycle
and leave unit non-operational.
3. Opens automatically when platform arrives at landing, pressing the call button, or
pulling on the gate.
4. ADA compliant.
5. Low voltage, 24 VDC with all wiring concealed.
J. Screw Drive:
1. Drive Type: Acme Screw Drive.
2. Travel speed: 10 fpm.
3. Motor: 1HP, 115 volt, 1 phase.
4. Power Supply:
a. 115 VAC, 30 Amp, Single Phase.
b. 230 VAC, 15 Amp, Single Phase.
5. Battery Powered Emergency Lowering:
a. Battery powered platform lowering device which automatically activates in the event
of power failure. Allows platform to be raised and lowered 5 times in event of power loss.
b. Capable of running lift up and down for a minimum of 5 trips with rated load.
6. The drive mechanism shall be a stationary nut on a rotating 1” diameter Acme screw
with a secondary safety nut.
K. Hydraulic Drive:
1. Drive Type: Chain Hydraulic.
2. Travel speed: 17 to 20 fpm.
3. Motor: 2HP, 24 VDC. AC powered primary drive.
4. Power Supply: 115 VAC, 15 Amp, Single Phase.
a. Powered by continuous building mains converted to 24 VDC equipped with auxiliary
battery power system. Battery power system capable of running lift up and down for a
minimum of 5 trips with rated load.
5. Standard on board 24 VDC standby battery power to operate the lift up and down in
the event of a power failure.
6. Drive mechanism shall be a 1:2 #60 roller chains hydraulic equipped with a type “A”
instantaneous slack chain safety device.
7. Hydraulic connections shall be metal and have rated pressure that withstands the
working pressure with a 5 times safety factor.
8. Bi-directional leveling, factory supplied oil collection means as required by A18.1-
8.1.4.7, Angled pressure gage standard, roller bearing sprockets, vibration isolated hydraulic
power unit.
L. Enclosure Panels:
1. 16 gauge galvanized steel.
2. Clear Plexiglas.
3. Bronze Plexiglas.
4. Laminated Safety Glass.
M. Lift Components:
1. Symmetry Elevating solutions PLC Controller with self diagnostics and digital display.
A.W.A.R.E. System (Active Wiring, Accessories, Relay & Electronics Diagnosis System)
generates on-demand diagnostic codes identifying trouble or maintenance codes.
2. The Drive Tower support shall be a combination 7 gauge C Channel, 7 gauge interface
plates and 16 gauge exterior skin.
3. Platform shall be constructed of 12-gauge minimum hot rolled steel. If unit is not
installed in a 3-inch pit, an auto-retracting ramp shall be provided that extends to meet lower
landing.
4. Platform side panels shall be 42” high, Side panel framework shall be a minimum of
1”x1 ½” steel. Solid infill panels shall be a minimum of 18 gauge steel.
5. Carriage platform supports shall be a minimum of ½” steel. Solid infill panels shall be
a minimum of 18 gauge steel.
6. Elevator style (Nylon) rollers shall be used for axial carriage guidance and wear pads
shall be used for horizontal stability.
7. Loaded fasteners shall be grade eight or higher. Locking fasteners shall be used in all
critical locations.
N. Enclosure Height Above Upper Landing:
1. Enclosure shall extend 42 inches above the upper landing level.
2. Enclosure shall extend 80 inches above the upper landing level.
3. 3 inches above with platform gate.
O. Drive Mast Side Wall Panels: Provide 16 gauge galvanized panels and mounting
hardware to cover the void between side of enclosure, drive mast and adjacent wall at the
following locations:
1. Lower Landing.
2. Intermediate Landing.
3. Upper Landing.
P. Platform Base & Frame Installation:
1. Pit Mount: (recess application) Level pit floor slab recessed min. 3” by others as
outlined on site specific show drawings. This application does not require ramp and allows for
smooth transition from landing into lifting equipment.
2. Floor Mount: (non-recess application) If unit is not installed in a min. 3” pit, an auto-
retracting ramp shall be provided that extends to meet the lower landing. Optional fixed
mounted ramp is available. (verify clear landing requirements if fixed ramp selected)
a. Platform Access Ramp: 12 gauge galvanized steel plates; slip resistant surfaces.
1. Ramp: Stationary type.
2. Ramp: Automatic folding type.
3. Carriage to be equipped standard with articulating base and carriage design, which
allows the carriage to be folded to reduce the tower and carriage width to 21” for ease of
installation, without removal of the carriage.
Q. Optional Features:
1. Enclosure Protection: Single sided or double sided roof. Angle and direction options
available.
2. Ventilation System: Single exhaust fan, thermostatically controlled with a 12 VDC
battery backup. Required continuous main power for Hydraulic Drive.
3. Outdoor Protection Package: Lift shall include modifications recommended by
manufacturer for performance in extreme outdoor weather conditions.
R. Platform Controls:
1. Constant pressure up/down control switches shall be installed on the platform. All
switches meet IP66 requirements.
2. An illuminated emergency stop switch / Audible alarm switch shall be provided on the
car as a means of signaling for assistance in the event of an emergency.
3. Keyless operation.
4. Keyed operation.
5. Emergency Telephone:
a. Wiring Only.
b. Platform shall be equipped with a telephone meeting the following requirements:
1. ADA compliant.
2. Shall be operational in the event of power failure.
3. Specified under Division 16 a telephone line shall be supplied to the lift.
S. Call Station Controls:
1. Constant pressure up/down control switch installed on the platform.
2. Constant pressure, elevator-style, hall call control stations provided at each landing.
3. Keyless operation.
4. Keyed operation.
5. Call Station Mounting:
f. Lower:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
g. Intermediate:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
h. Upper:
1. In-Frame.
2. Surface Mount.
3. Flush Mount.
T. Safety Features/Devices:
1. Grounded electrical system with upper, lower, and final limit switches.
2. A grab rail shall be provided on the platform.
3. A gate with a min. height of 42” and a combination mechanical lock with an electric
contact shall be provided at the upper landing, lock must be engaged for lift to move from
landing.
4. At all landings an electromechanical interlock shall be used to keep doors closed when
lift is on another floor.
5. Electrical disconnect which will shut off power to the lift.
6. Pit stop switch mounted on mast wall.
U. Finishes:
1. Finish shall be electro statically applied powder coating, oven baked to cure.
2. Color:
a. Ivory.
b. White.
c. Black.
d. Grey.
e. A selection from 213 RAL colors.
2.05 HYBRID VERTICAL WHEELCHAIR LIFT:
B. General Description: The Hybrid looks and feels like an elevator, but operates like a
lift. Available in many different sizes and configurations, features include a full height cab,
non-load bearing ceiling and a wide variety of optional features and finishes. Customize the
doors and cab to match the style and décor of your commercial facility or home.
C. Capacity:
1. 750 lbs.
D. Lifting Height:
1. Up to 120 inches.
2. Up to 180 inches.
3. Up to 240 inches.
E. Platform Size:
1. 36” W x 48” D
2. 36” W x 54” D
3. 36” W x 60” D
4. 42” W x 60” D
5. 42” W x 60” D
F. Platform Configuration:
1. Straight Through.
2. Enter/Exit same side.
3. 90 Degree.
G. Landing Openings:
1. All Landings: Doors interlocked with lift controls.
H. Door Construction:
1. A CSD-Rated (R) Fire Rated (B Label) flush mounted steel door and frame shall be
provided. Door shall include wire mesh vision panel with delay action door closure, dead
latch, dummy trim door handle and electric strike.
2. A CSD – Non-Rated (NR) Low profile flush mounted steel door and frame shall be
provided. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
a. Panels of 16 gauge galvanized steel.
b. Panels of clear Plexiglas.
c. Panels of bronze Plexiglas.
d. Panels of ¼ inch laminated safety glass.
3. A CWS – Flush mounted, solid core oak laminated door and (oak) frame shall be
proved. Door shall include mesh vision panel with delay action door closure, dead latch,
dummy trim door handle, lock plate cover and electric strike.
4. A 24V DC, fail secure electric strike that contains electric contacts to insure the door is
both closed and locked shall be provided. (This option is required when flush mounted door
frames are provided by others.)
I. Provide Power Door/Gate Operator:
1. ADA Compliant and obstruction sensitive.
2. Door opens and closes at landing.
3. Location:
a. Lower Landing: Door & Car Gate.
b. Intermediate Landing (s): Door & Car Gate.
c. Upper Landing: Door & Car Gate.
J. Hydraulic Drive:
1. Drive Type: Roped Hydraulic.
2. Travel speed: 30 fpm.
3. Motor: 3HP, 208/230 VAC. Submersed Power Unit.
4. Power Supply: 208/230 VAC, 30 Amp, Single Phase
5. Standard on board 24 VDC standby battery power to operate the lift up and down in
the event of a power failure.
6. Drive mechanism shall be a 1:2 roped hydraulic with type “A” instantaneous slack
rope safety device.
7. Hydraulic connections shall be metal and have rated pressure that withstands the
working pressure with a 5 times safety factor.
8. Bi-directional leveling, factory supplied oil collection means as required by A18.1-
8.1.4.7, vibration isolated hydraulic power unit.
K. Lift Components:
1. Heavy duty car sling with roller guide wheels running on 6-1/4 lb. per foot steel T-
rails, quiet submersed pump and motor (3 HP), factory pre-set and tested 2-speed valve for
smooth start and stop. Pump unit to be located in a machine room outside of the hoistway.
2. Symmetry Elevating solutions PLC Controller with self diagnostics and digital display.
S.M.A.R.T. System (Self-Monitoring Alert Response Technology) generates on-demand
diagnostic codes identifying trouble or maintenance codes, and broadcasts these codes to
the controller, Hall Stations, and to the Car.
3. Loaded fasteners shall be grade eight or higher. Locking fasteners shall be used in all
critical locations.
L. Lower Landing Pit:
1. 6 inches minimum.
2. 8 inches preferred.
M. Car Controls:
1. Fully automatic illuminated push button.
a. Braille Illuminated Buttons.
2. An illuminated emergency stop switch / Audible alarm switch shall be provided on the
car as a means of signaling for assistance in the event of an emergency.
3. Keyless operation.
4. Keyed operation.
5. Digital Floor Display.
6. Emergency Telephone:
a. Wiring Only.
b. Platform shall be equipped with a telephone meeting the following requirements:
1. ADA compliant.
2. Shall be operational in the event of power failure.
3. Specified under Division 16 a telephone line shall be supplied to the lift.
N. Call Station Controls:
1. Fully automatic illuminated push button.
a. Braille Illuminated Buttons.
2. Hall Station Type:
a. Keyless Operation.
b. Keyed Operation.
3. Finish:
a. Brushed Stainless.
b. Polished Stainless.
c. Brushed Brass.
d. Polished Brass.
e. Oil Rubbed Brass.
f. Vintage Bronze.
g. Black.
h. Cooper – Silver.
i. Brushed Silver.
j. Natural Metal.
k. Brushed Bronze.
l. Japanese Brown.
m. Antique Brown.
4. Call Station Mounting:
a. Lower Floor:
1. Wall mounted recessed.
2. Mounted within the door frame.
b. Second Floor:
1. Wall mounted recessed.
2. Mounted within the door frame.
c. Third Floor:
1. Wall mounted recessed.
2. Mounted within the door frame.
d. Upper Floor:
1. Wall mounted recessed.
2. Mounted within the door frame.
O. Safety Features/Devices:
1. Motor Controller supply disconnect (located in controller).
2. Safety switch for car gate(s).
3. Electromechanical hoistway door interlocks.
4. Recessed Phone box.
5. Rupture Valve (Type “C” Safety)
6. Emergency alarm button in car, Emergency keyed stop switch in car.
7. Battery backup emergency car lights and alarm.
8. Upper and lower final limit switches.
9. Low oil protection timer circuit.
10. Grounded electrical system with upper, lower, and final limit switches.
11. Electrical disconnect which will shut off power to the lift.
12. Pit stop switch mounted on mast wall.
P. Cab Design:
1. Interior Walls: Panel selections.
a. Flat Panel.
b. Shaker Panel.
c. Inset Panel.
d. Raised Panel.
2. Interior Walls: Wood Species.
a. Alder.
b. Birch.
c. Cherry.
d. Hickory.
e. Mahogany.
f. Maple.
g. Red Oak.
h. Walnut.
i. White Oak.
3. Interior Walls: Stain.
a. No Stain – Unfinished.
b. Country Pine.
c. Golden Oak.
d. Satin Clear Coat.
e. Traditional Cherry.
f. Custom as selected by Architect.
4. Ceiling: Panel selections.
a. Flat Panel.
b. Shaker Panel.
c. Inset Panel.
d. Raised Panel.
5. Ceiling: Wood Species.
a. Alder.
b. Birch.
c. Cherry.
d. Hickory.
e. Mahogany.
f. Maple.
g. Red Oak.
h. Walnut.
i. White Oak.
6. Ceiling: Stain.
a. No Stain – Unfinished.
b. Country Pine.
c. Golden Oak.
d. Satin Clear Coat.
e. Traditional Cherry.
f. Custom as selected by Architect.
7. Car Operating Panel Finish:
a. Brushed Stainless.
b. Polished Stainless.
c. Brushed Brass.
d. Polished Brass.
e. Oil Rubbed Brass.
f. Vintage Bronze.
g. Black.
8. Handrail Finish:
a. Matching Wood.
b. Brushed Stainless.
c. Polished Stainless.
d. Brushed Brass.
e. Polished Brass.
f. Vintage Bronze.
g. Oil Rubbed Brass.
9. Floor: Unfinished ¾ inch plywood construction.
10. Lighting:
a. 115 VAC, single phase, 15 Amps.
b. Failure of one lamp shall not cause the remaining lamps to extinguish.
c. Lights shall illuminate automatically when the elevator door is opened and remain on
the entire duration of use. Lights shall automatically turn off after a preset time the elevator
is not in use.
d. Recessed LED Lights with Trim.
1. (2) Two.
2. (4) Four.
e. Finish:
1. Black Trim.
2. Brushed Stainless.
3. Bronze.
4. Polished Brass.
PART 3 EXECUTION
3.01 ACCEPTABLE INSTALLERS:
A. Subcontractor Qualifications: A company that is listed as an authorized Symmetry
Elevating Solutions dealer. See www.symmetryelevator.com for details.
B. Electrical devices, service and final connections shall be by a qualified electrician.
3.02 EXAMINATION:
A. Preliminary work must be properly prepared, including hoistway construction (if
needed), landings and machine space, before installation.
B. Verify hoistway shaft (if needed) and machine space are the correct size and within
acceptance.
C. Verify required landings and openings are the correct size and within acceptance.
D. When required verify machine room is provided with lighting, light switch, outlets and
meets the clear space requirements of ASME A17.1.
E. Verify electrical power is available and of within acceptance.
F. Notify Architect of any inadequate preparation when preliminary work is the
responsibility of another installer.
3.03 PREPARATION:
A. Clean surfaces thoroughly prior to installation.
B. Prepare surfaces and unit using the methods recommended by the manufacturer for
achieving the optimum performance of vertical wheelchair lift.
3.04 INSTALLATION:
A. Unit shall be installed and operated in accordance with the ICC/A117.1, NEC and
ASME A18.1 Guidelines.
B. A dedicated electrical supply provided to the disconnect shall be capable of supplying
sufficient power.
C. GC to coordinate “work by others” with lift contractor.
D. The installation of the vertical wheelchair lift shall be made in accordance with
approved plans and specifications and the manufacturer’s installation instructions.
E. Startup and test unit in accordance with manufacturer’s instructions.
F. Adjust for smooth operation.
3.05 FIELD QUALITY CONTROL:
A. Perform tests in compliance with ASME 17.1 or A18.1 and as required by authorities
having jurisdiction.
B. Load the vertical lift to rated capacity and test for several cycles to insure proper
operation. No mechanical failures shall occur and no wear that would affect the reliability of
the unit shall be detected.
C. Schedule necessary tests with Architect, Owner, Contractor, and any authorities
having jurisdiction.
3.06 PROTECTION:
A. Protect installed products until completion of project.
B. Touch-up, repair or replace damaged products before Substantial Completion.
C. Clean unit prior to final inspection
REFERENCE: Home Elevator - Hydraulic Drive – Symmetry Elevating Solutions - Sweets
(construction.com)
Vertical Platform Lift - Enclosed Lift Plexi-glass – Symmetry Elevating Solutions -
Sweets (construction.com)
DIVISION 15 – Mechanical
PRODUCT DESCRIPTION:
Elkay sink accessories are designed to fit perfectly and
coordinate with your Elkay sink. From color matched drains
to custom-sized stainless steel sink grids and wood cutting
boards, we have what you need.
P-Trap - LK500
LK500 - Elkay P-Trap with Cleanout Plug
Elkay sink accessories are designed to fit perfectly and
coordinate with your Elkay sink. From color matched drains
to custom-sized stainless steel sink grids and wood cutting
boards, we have what you need. Our accessories make the
time at your kitchen, prep, bar or laundry sink more convenient, efficient and effortless.
 1 1/2 foot trap with clean out.
PRODUCT SPECIFICATIONS:
Elkay P-Trap with Cleanout Plug. Overall dimensions are 13-3/4" x
1-1/2" x 6". Made of Chrome-plated Brass.
Material: Chrome-plated Brass
Finish: Chrome (CR)
Dimensions: 13-3/4" x 1-1/2" x 6"
Shipping Weight: 2 lbs.

Elkay Accessory Care and Cleaning

Elkay | 1333 Butterfield Road, Suite 200 | Downers Grove, IL 60515 | 800.223.5529 |
elkay.com 1000005391 7/19
With proper care and maintenance, your Elkay accessores will give you a lifetime of
service. Below are the suggestions for the care and cleaning of your Elkay accessories.
General Cleaning
It is recommended to clean Elkay accessories daily to avoid build-up of soap or mineral
deposits, as these tend to have an adverse effect on the appearance of the product. For
daily cleaning use an ordinary mild detergent and soft cloth to rinse and dry the sink.
Allowing water or cleaners to evaporate will negatively impact the look of the accessory.
To avoid this, it is important to dry the accessory after each use.
• Elkay colanders, cutting boards, rinsing baskets and bottom grids are not
designed as "Dishwasher Safe" or "Microwave Safe".
• These products should be hand washed in a mild detergent, rinsed thoroughly and hand
dried.
• For wood cutting boards – apply a coat of mineral oil to all wood surfaces on a monthly
basis or more frequently if needed.

Bottom Grids
• Check to see that all rubber or vinyl feet and bumpers are in place before using
wire accessories.
• Do NOT use scouring pads, abrasive cleaners, and harsh detergents.
• Some accessories are designed with a tight fit to help secure them into place.
Cutting Boards
The following are recommendations from the USDA regarding cutting boards:
• Always use a clean cutting board.
• If possible, use one cutting board for fresh produce and a separate one for raw
meat, poultry and seafood.
• Once cutting boards become excessively worn or develop hard-to-clean grooves,
you should replace them.
REFERENCE: P-Trap - LK500 – Elkay - Sweets (construction.com)

PRODUCT DESCRIPTION:
LATICRETE International, Inc. - HYDRO BAN® Bonding
Flange Drains
HYDRO BAN Bonding Flange Drain and the HYDRO BAN
Bonding Flange Tile Drain are low profile floor drains
specifically designed for bonded waterproofing
installations with HYRDO BAN waterproofing membrane,
the grates are 4”x4” (10 x 10 cm) to match most
common tile sizes.

HYDRO BAN Bonding Flange Drain and the

HYDRO BAN Bonding Flange Tile Drain are low
profile floor drains specifically designed for bonded
waterproofing installations with HYDRO BAN waterproofing membrane. HYDRO BAN
Bonding Flange Drains allow for the installation in a shower eliminating the pre-slope
and primary shower pan liner according to TCNA Method B422. The HYDRO BAN
Drain Grates sold with the bonding flanges are 4”x4” (10 x 10 cm) to match most
common tile sizes.

 Product #: 9XXX-XXXX-XX
  Packaging Sizes:

The HYDRO BAN Bonding Flange Drain is a three-piece drain flange,

adjusting ring and a 4" x 4" (102 x 102 mm) grate assembly in brushed,
polished or oil rubbed bronze stainless steel.

The HYDRO BAN Bonding Flange Tile Drain is a four-piece drain flange,
adjusting ring and a 4" x 4" (102 x 102 mm)) grate assembly that can be tiled
to match the shower floor. All Bonding Flange Drains are available with either
PVC or ABS Bonding Flange. When ordering a HYDRO BAN Bonding Flange
Drain check with local code official to determine whether a PVC or ABS
HYDRO BAN Bonding Flange Drain is required. Most areas in the United
States will require a PVC drain connection except California and some
surrounding states.

 Part of System: LATICRETE®

Features & Benefits

 Grates are 4”x4” (10 x 10 cm) to match most common tile sizes
 Attaches to 2" (50 mm), 3" (76 mm) and 4" (102 mm) waste lines
 Tile-in grate available to match floor tile
 Eliminates pre-slope and primary shower pan for a faster installation
 Made from heavy duty PVS or ABS and 304 stainless steel to provide long
lasting performance
 HYDRO BAN waterproof membrane bonds directly to PVC or ABS flange
 Integrates seamlessly with portland cement mortar beds waterproofed with
HYDRO BAN
USES:
■ Interior use only.
■ Industrial, commercial and residential bathrooms where
a pre-sloped shower pan is required.
■ Can be installed for ADA compliance.
■ Stalled gang showers.
■ Pet showers.
SUITABLE SUBSTRATES (INTERIOR ONLY)
■ Concrete
■ Masonry
■ Tile and Stone
■ Exterior Glue Plywood
■ Cement Backer Board *
■ OSB or Advantech
* Consult cement backer board manufacturer for specific
installation recommendations.
SIZES:
HYDRO BAN® PRE-SLOPED SHOWER PANS
(drain grates sold separately)
CENTER DRAINS
48" x 48" (122 cm x 122 cm) ABS or PVC
36" x 60" (91 cm x 152 cm) ABS or PVC
36" x 48" (91 cm x 122 cm) ABS or PVC
48" x 60" (122 cm x 152 cm) ABS or PVC
OFF CENTER DRAIN
38" x 66" (96 cm x 168 cm) ABS or PVC.
HYDRO BAN LINEAR PRE-SLOPED SHOWER PANS
(linear drains sold separately)
■ 34" x 66" (86 cm x 168 cm)
■ 38" x 66" (97 cm x 168 cm)
■ 44" x 66" (112 cm x 168 cm)
■ 50" x 66" (127 cm x 168 cm)
■ Custom sizes available
HYDRO BAN Linear Drains are sold separately. When installing a:
■ 34" x 66" (86 cm x 168 cm) pan use a 32" (81 cm)
linear drain
■ 38" x 66" (97 cm x 168 cm) pan use a 36" (91 cm)
linear drain
■ 44" x 66" (112 cm x 168 cm) pan use a 42" (107 cm)
linear drain
■ 50" x 66" (127 cm x 168 cm) pan use a 48" (122 cm)
linear drain
Each package contains one HYDRO BAN Pre-Sloped Shower Pan,
one HYDRO BAN Preformed Curb, and one tube of HYDRO BAN
Adhesive & Sealant. The HYDRO BAN® Pre-Sloped Shower Pan and
HYDRO BAN Linear Pre-Sloped Shower Pan are also available in
custom sizes and shapes.
HYDRO BAN PRE-SLOPED RAMP
13-1/2" (34 cm) wide by 60" (152 cm) long packaged one
per carton.
LIMITATIONS
n Adhesives/mastics, mortars and grouts for ceramic tile, pavers,
brick and stone are not replacements for waterproofing membranes.
When a waterproofing membrane is required, use HYDRO BAN
liquid or HYDRO BAN Sheet Membrane.
n Do not expose unprotected HYDRO BAN Pre-Sloped or Preformed
products to sun or weather for more than 30 days.
n Do not expose to rubber solvents or ketones.
n Must be covered with ceramic tile, stone, finish. Use protection
board for temporary cover prior to finishing.
n When installing tile less than 2"x2" (50 x 50 mm) the installation
must be grouted using SPECTRALOCK® PRO Premium Grout.
 n HYDRO BAN Pre-Sloped Shower Pans and HYDRO BAN Preformed
Curbs and Ramps are rated to 40 psi (0.3 MPa).
n A wooden 2"x4" (51 x 102 mm) curb structure with HYDRO BAN
Curb Overlay is required when installing hinge less glass doors /
European-style glass enclosures with pins.
NOTE: Surfaces must be structurally sound, stable and rigid enough to
support ceramic/stone tile and similar finishes. Substrate deflection
under all live, dead and impact loads, including concentrated loads, must
not exceed L/360 for thin bed ceramic tile installations or L/480 for
thin bed stone installations.
3
CAUTIONS
n During cold weather, protect finished work from traffic until
fully cured.
n For white and light-colored marbles, use a white polymer fortified
portland cement thin set mortar.
n For green and moisture sensitive marble, agglomerates and resin
backed tile and stone use LATAPOXY® 300 Adhesive (refer to
Data Sheet 633.0).
n If the waterproof coating on the HYDRO BAN Pre-Sloped or
Preformed product is punctured during installation or from job site
construction activity re-coat the punctured area and 2" (50 mm)
around the area with two coats of HYDRO BAN, follow DS 663.0
or DS 663.5 for full instructions.
n Use care not to damage surface of HYDRO BAN Pre-Sloped or
Preformed products prior to installation of tile or stone finishes.
Cover with protection board to protect from foot traffic and
other trades.
WATERPROOFING BARRIER FREE SHOWER INSTALLATIONS
Shower walls with cement backer board construction can be
waterproofed using either HYDRO BAN liquid applied waterproofing
membrane following the respective data sheet and installation guide
DS 663.0 and DS 663.5 or HYDRO BAN Sheet Membrane following
data sheets and installation guides DS 041.0, DS 043.5.
INSTALLATION
INSTALLATION OVER CONCRETE OR WOOD JOIST
SUPPORTED FLOORING
The HYDRO BAN Pre-Sloped Shower Pan can be installed over a
concrete or wood joist supported floor along with a HYDRO BAN
Pre-Sloped Ramp. Follow the recommendations in detail ES-WP313
below and the data sheets for the installation of the HYDRO BAN
Pre-Sloped Shower Pan DS 031.0 and the HYDRO BAN Pre-Sloped
Ramp DS 063.0 to create a barrier free or ADA compliant shower.
If a barrier free shower is desired using a HYDRO BAN Linear Drain and a HYDRO BAN Linear
Pre-Sloped Shower Pan installed over a concrete or wood joist supported floor, a ramp can
be formed using 3701 Fortified Mortar. The HYDRO BAN Linear Drain can be placed at the
door following the recommendations in detail ES-WP305L Linear EGP Curbless Door or
against the wall opposite the door as in detail ES-WP305L Linear EGP below. When the
HYDRO BAN Linear drain is installed at the door, the ramp formed using the 3701 Fortified
Mortar should slope from the room toward the drain. When the HYDRO BAN Linear drain is
installed at the wall opposite the door, the ramp formed using the 3701 Fortified Mortar
should slope from the door toward the drain. Follow the data sheets for the installation of
the HYDRO BAN Pre-Sloped Shower Pan DS 031.0, the HYDRO BAN Pre-Sloped Ramp DS 063.0
and 3701 Fortified Mortar DS 100.0 to create a barrier free or an ADA compliant shower.

INSTALLATION OVER RECESSED CONCRETE

Recess the concrete floor for the appropriate height of the HYDRO BAN Pre- Sloped Shower
Pan. HYDRO BAN Linear Pre-Sloped Shower Pan or to accommodate a 3701 Fortified Mortar
sloped to TCNA or ADA recommendations. The HYDRO BAN Linear Drain can be placed at the
door following the recommendations in detail ES-B300LM- Recessed Linear Drain – Medial
Curbless w/Door for a 3701 Fortified Mortar installation or ES-B300LM-Recessed Linear Pan-
Curbless w/Door for a HYDRO BAN Linear Pre-Sloped Shower Pan installation. When installing
a linear drain and pre-sloped shower pan follow the data sheets for the installation of the
HYDRO BAN Linear Drain DS 034.0 and HYDRO BAN Linear Pre-Sloped Shower Pan DS 085.0.
When installing the HYDRO BAN Linear Drain against the wall opposite the door follow the
recommendations in detail ES-WP305L Linear EGP-Curbless below. This installation can be
done with a HYDRO BAN Linear Pre-Sloped Shower Pan or by using 3701 Fortified Mortar.
When installing a linear drain and pre-sloped shower pan follow the data sheets for the
installation of the HYDRO BAN Linear Drain DS 034.0 and HYDRO BAN Linear Pre-Sloped
Shower Pan DS 085.0 or 3701 Fortified Mortar DS 100.0 to create a barrier free or ADA
compliant shower. When installing a HYDRO BAN Pre-sloped Shower Pan (Detail not shown)
follow the data sheets for the installation of the HYDRO BAN Pre-Sloped Shower Pan DS 031.0
to create a barrier free or ADA compliant shower.
INSTALLATION OVER RECESSED WOOD JOISTS
When installing a barrier free shower over recessed wood joist flooring the sub floor and
underlayment need to be removed to accommodate the shower pan. The existing floor joists
need to be sistered by adding 2" x 4" (50 x 100 mm) to either side of the floor joist and two
on either side of the waste outlet 8" (203 mm) apart. The 2" x 4"s (50 x 100 mm) should be
installed ¾" (19 mm) below the top of the floor joists.
Cut 3/4" nominal EGP to fit on top of the 2"x4"s and install the EGP so the top of the EGP is
flush with the original floor joists, Shown below. When installing a linear drain, cut a 3" (76
mm) hole in the substrate where the drain outlet will pass through the 3/4" nominal EGP.
The center of the waste line should be located 2 1/4" (57mm) out from the sill plate when
the drain is installed on the opposite wall from the door or centered at the entry to the
shower if located at the door. If the domestic waste line is already in place cut the waste line
1-3/4" (44 mm) below floor level.
The HYDRO BAN Linear Drain can be placed at the door following the recommendations in
detail ES-WP305L Linear EGP - Door using a HYDRO BAN Linear Pre-Sloped Shower Pan.
When installing a linear drain and pre-sloped shower pan follow the data sheets for the
installation of the HYDRO BAN Linear Drain DS 034.0 and HYDRO BAN Linear Pre-Sloped
Shower Pan DS 085.0 or DS 100.0 for 3701 Fortified Mortar to create a barrier free or ADA
compliant shower.
INSTALLATIONS IN FLOOR MORTAR
All of the barrier free shower installations can be done using a pre-sloped shower pan or by
the conventional method using 3701 Fortified Mortar in a bonded or unbonded installation
to concrete or wood joist supported flooring substrate. The detail below show
recommendations for barrier free showers using a HYDRO BAN Bonding Flange drain (detail
ES-B300-BFD) or a HYDRO BAN Linear Drain along the wall detail: ES-B300LD-Bonded (Corner
Placement) or ES-B415LD-Bonded (Corner Palcement), medial detail: ES-B300LM-Linear
Drain-Medial or in the entryway to the shower with a door, detail: ES-B300LM-Linear Drain-
Medial Curbless w/ Door.
AVAILABILITY AND COST
Availability
LATICRETE and LATAPOXY® materials are available worldwide.
For Distributor Information:
Toll Free: 1.800.243.4788
Telephone: +1.203.393.0010
For on-line distributor information, visit LATICRETE at www.laticrete.com
Cost Contact a LATICRETE Distributor in your area.
WARRANTY
See 10. FILING SYSTEM:
DS 230.13: LATICRETE Product Warranty
A component of
DS 230.10: LATICRETE 10 Year System
Warranty (United States & Canada)
DS 025.0: LATICRETE 25 Year System
Warranty (United States and Canada)
DS 230.99: LATICRETE Lifetime System
Warranty (United States and Canada)
MAINTENANCE
The non-finish or non-exposed portion of the HYDRO BAN Shower
System products require no maintenance. However, installation
performance and durability may depend on properly maintaining
products and finishes that cover the HYDRO BAN Shower System
products and those supplied by other manufacturers. The exposed
portion of the stainless steel HYDRO BAN Drain Grates can be cleaned
and maintained using a non-abrasive stainless steel cleaner or polish
with a clean soft white cotton cloth. When cleaning the HYDRO BAN oil
rubbed bronze Drain Grate use a non-abrasive cleaner and clean soft
cloth. When choosing the HYDRO BAN Drain Grate in oil rubbed bronze
contact the cleaner manufacturer if another cleaner type will be used to
ensure compatibility with the drain material.
TECHNICAL SERVICES
Technical Assistance
Information is available by calling
Toll Free: 1.800.243.4788, ext. 235
Telephone: +1.203.393.0010, ext. 235
Fax: +1.203.393.1948
Technical and Safety Literature
To acquire technical and safety literature, please visit our website at
www.laticrete.com.
FILING SYSTEM
Additional product information is available on our website at
www.laticrete.com.
The following is a list of related documents:
DS 230.13: LATICRETE Product Warranty
DS 230.10: LATICRETE 10 Year System
Warranty (United States & Canada)
DS 025.0: LATICRETE 25 Year System
Warranty (United States and Canada)
DS 230.99: LATICRETE Lifetime System
Warranty (United States and Canada)
DS 100.0: 3701 Fortified Mortar
DS 663.0: HYDRO BAN
DS 663.5: HYDRO BAN How to Instructions
DS 035.0: HYDRO BAN Bonding Flange Drain
DS 034.0: HYDRO BAN Linear Drain
DS 031.0: HYDRO BAN Pre-Sloped Shower Pan
DS 035.0: HYDRO BAN Linear Pre-Sloped Shower Pan
DS 063.0: HYDRO BAN Pre-Sloped Ramp
DS 041.0: HYDRO BAN Sheet Membrane
DS 681.0 SPECTRALOCK® PRO Premium Grout†
DS 080.0 4-XLT
DS 677.0 254 PLATINUM
DS 681.0 LATAPOXY® 300 Adhesive
REFERENCE: HYDRO BAN® Bonding Flange Drains – LATICRETE International, Inc. - Sweets
(construction.com)
DIVISION 16 – Electrical
PRODUCT DESCRIPTION:
Westgate Mfg. - Outdoor Lighting - LF3 Flood Light
Series with Slip Fitter
 Housing: Die-cast aluminum housing with
powder coat finish (Dark Bronze)
 Installed slip fitter for mounting on mounting
tubes (tenon) of max 2-3/4" O.D.
 Voltage: 120~277V; 60Hz AC
 0~10V dimming (except 80W)
Technical Specs
 Housing: Die-cast aluminum housing with
powder coat finish (Dark Bronze)
 Installed slip fitter for mounting on mounting tubes (tenon) of max 2-3/4" O.D.
 Voltage: 120~277V; 60Hz AC
 0~10V dimming (except 80W)
 Type II lens (TYPE III & IV by request)
 Power Factor: .9~.97
 Operating Temp:-4°F to 104°F
 Up to 100 lumens per watt
 CRI: 82~84
 Beam Angle: 104°
 70,000 hour rated life
 7-year warranty
 Suitable for Wet Locations, IP65
 1/2" HUB for photocell or sensor installation
Applications
 Ideal for general site lighting, alleys, loading docks, doorway, pathway and parking
areas.
 Replace existing HID flood lights/ wall packs
 Great for use with motion sensors or other instant on/off controls
REFERENCE: Outdoor Lighting - LF3 Flood Light Series with Slip Fitter – Westgate Mfg. - Sweets
(construction.com)
Green Frog Systems - GFS-ASPIRE Solar Light
Designed in Australia to meet the increasing demand for
smart connected lighting infrastructure the GFS-ASPIRE
offers an environmentally friendly, off-grid connected solar
option where traditional lighting is impractical or cost
prohibitive.

GFS-ASPIRE Solar Light

Designed in Australia to meet the increasing demand for
smart connected lighting infrastructure the GFS-ASPIRE
offers an environmentally friendly, off-grid connected solar option where traditional lighting
is impractical or cost prohibitive.
The scalable modular design enables various configurations depending on the application /
requirements.
Multiple panels, pole heights and battery arrangements are supported with the ASPIRE as
well as SAM (Solar Activity Monitoring) software connection enabling centralised monitoring
and control of the lighting assets from a remote dashboard.
Green Frog Systems design and develop smarter solar lighting technology world wide. The
ASPIRE range of solar street lights has been developed with elegance in mind, meeting the
evolving standards of contemporary architectural design and the built environments of
tomorrow.
APPLICATIONS
• Streets
• Roadways
• Intersections
• Car Parks
• Industrial
• Commercial
• Parks
• Recreation
SPECIFICATIONS
MODEL GFS-ASPIRE
OPERATING PROFILE / OPERATION MODES
Standard operation is all night mode with additional sensor mode:
All night mode - Operates at a constant level of illumination between 1-85W (up to 15,895lm)
until dawn.
Sensor mode - Detects movement and increases illumimation by 15W (+2805lm) until no
motion is detected for 30 seconds.
Configurable TIMER settings for ON / OFF / DIM are available upon request.
LED
Type CREE XP-G LED
Watts (Light Output) 70W (Standard) /15W (PIR Boost)
Lumens 13,090lm (Standard) 18,700lm (with PIR Boost)
CCT (Colour Temperature) 4000K (Standard) / 3000K (Optional)
Optics T3 (Standard) 135° x 85° | T5 (Optional) 110° x 135°
BATTERY
Autonomy 98 hours (8 nights)*
Battery Type / Capacity 2 x LiFePO4 25.6V 28.8Ah (1474Wh) batteries
SOLAR PANEL
Watts (p) / Type 225W Monocrystalline panel 360° rotatable with 0-60° tilt
Efficiency 24%
UNIT
Sail Area / EPA 0.65m2 / 7 FT2 @ 30° mounting angle
Pole Single piece galvanised
Package Dimensions Crate: 1650 x 880 x 560 mm / 65" x 35" x 22"
Pole: 6000 x 610 x 310 mm / 236.2" x 24" x 12.2"
Package Weight Crate: 191 kg / 421 lb
ENVIRONMENTAL
Operating Temp. Range -20°C to 60°C / -4°F to 140°F
IP Rating IP68 waterproof construction and connectors
WARRANTY
Warranty Period 5 years (Unit) / 10 years (Battery) / 25 years (Solar Panel)**
OPTIONS
3000K CCT
Up to four (4) LiFePO4
ACT batteries (2949Wh)
IoT smart city ready with GFS-SAM monitoring system
Solar panel bird guard (Portrait or Landscape)
Twin / Triple solar panel mounting bracket
Twin head configuration