System Description

4.3. Harmony XL Pro /SE Modules – General Description

The Harmony XL Pro /SE system operates with various modules using diverse
technologies. Each handpiece comprises a complete module and incorporates
the entire optical bench that emits the light or laser beam.
Each module is connected to the system console by an umbilical cable that
houses the wiring and cooling water tubes. The Harmony XL Pro /SE cannot be
operated unless a module is connected to the system.
The operating parameters of all Harmony XL Pro /SE modules are pre-
programmed. The particular specifications and operating parameters for
each module can be found in the Modules Manual.
The modules are also preprogrammed to a given energy range based on their
intended use. The operator can adjust the energy fluence within the predetermined
range.

4.3.1 Applicators Description

Applicators Application Wavelength (nm)

Laser Applicators
ClearSkin PRO 1540 Skin Rejuvenation 1540
Additional: Acne vulgaris and acne
scars
ClearLift - QS High Power Tattoo removal, benign pigmented 1064; 532
(Nd:YAG 1064nm & KTP 532nm) lesions, Melasma and skin rejuvenation
including skin laxity and wrinkles
ClearSkin (Er:Glass 1540nm) Acne vulgaris and acne scars 1540
LP 1064nm YAG Cooled Benign vascular lesions, leg veins, hair 1064
removal, wrinkles and
Pseudofolliculitis
Barbae
ER iPixel high power pro (Er:YAG Fractional ablative skin resurfacing, 2940
2940nm) wrinkles, scars and skin lesions

Cooled AFT Applicators

Dye VL PRO Vascular and pigmented lesions 450-600
VP 540 Vascular and pigmented lesions 540-950
SR 570 Pigmented epidermal lesions 570-950
Dye VL Vascular and pigmented lesions 500-600
Dye SR Vascular and pigmented lesions 550-650
SHR Pro (5 cm2) Hair removal 690-950
Speed AFT SHR Pro (6.4 cm2) Hair removal 700-950

Non-Cooled AFT Applicators

UVB High Power Psoriasis and Vitiligo 270-380
Acne 420 Moderate inflammatory acne vulgaris 420-950
SR 570 Pigmented epidermal lesions 570-950
NIR Face (6 cm2) Muscle pain and joint pain, 1000-1500nm (Peak at 1300nm)
improvement
in skin laxity and muscular back pain
NIR Body (18 cm2) Muscle pain and joint pain, 1000-1500nm (Peak at 1300nm)
improvement
in skin laxity and muscular back pain

Harmony XL Pro /SE System Service Manual 4-8

 System Description
4.4. System Specifications
Pulse
Spot Size Wavelength Pulse Widths / Energy Density
Module Light Source 2 Mode Repetition Rate 2
(cm ) (nm) Timers (Hz) (J/cm )
2
Cooled IPL Module 5 cm spot size
SHR Pro (5) HR 30, 40, 50 msec 1/2 5-20
Flash lamp 5 650-950
Cooled
SHR Timer: 1,3,30 sec 3 3-7
2
Cooled IPL Module 3 cm spot size
SVL Cooled Flash lamp 3 515-950 10, 12, 15 msec 2/3 5-30
VL/PL Cooled Flash lamp 3 440-950 10, 12, 15 msec 2/3 5-30
SR Cooled Flash lamp 3 570-950 10, 12, 15 msec 2/3 5-30
Dye-SR 10, 12, 15 msec 1/2 Up to 14
Dye-SR Pro Flash lamp 3 550-650
Dye-SSR Timer: 1,3, 30 sec 3 1-4
Dye-VL 10, 12, 15 msec 1/2 Up to 15
Dye VL-Pro Flash lamp 3 450-600
Dye-SVL Timer: 1,3, 30 sec 3 1-4
SHR Pro (3) HR 30, 40, 50 msec 1/2 5-25
Flash lamp 3 650-950
Cooled
SHR Timer: 1,3,30 sec 3 3-7
SSR Cooled Flash lamp 3 540-950 Timer: 1,3,30 sec 2 1-15
SST Cooled Flash lamp 3 780-950 Timer: 1,3,30 sec 5 0.5-3.5
2
Non cooled IPL Module 6.4 cm spot size
SVL Flash lamp 6.4 515-950 10, 12, 15 msec 2/3 5-25
VL/PL Flash lamp 6.4 440-950 10, 12, 15 msec 2/3 5-25
SR Flash lamp 6.4 570-950 10, 12, 15 msec 2/3 5-25
HR Flash lamp 6.4 650-950 30, 40, 50 msec 1/2 5-25
ST Flash lamp 6.4 780-950 Timer: 10,30,90 sec 2 1-7
Acne 30, 40, 50 msec 1/2 5-25
Acne Flash lamp 6.4 420-950
S-Acne 2 msec 10 0.3-1.2
High Power UV Flash lamp 6.4 270-380 30, 40, 50 msec 1/2 2-4.5

Harmony XL Pro /SE System Service Manual 4-11

System Descripti on Pulse
Spot Size Wavelength Pulse Widths / Energy Density
Module Light Source 2 Mode Repetition Rate 2
(cm ) (nm) Timers (Hz) (J/cm )
NIR Module
NIR Face Lamp 6.4 1300 N/A 5-25 W
LED Module
Pulsed Up to 70 sec. Pulsed
Yellow LED LED array 560-620 1.5W
CW Up to 70 minutes CW

Waveleng Pulse Energy Density /

Module Technology Spot size(mm) Pulse Width
th (nm) Frequency (Hz) Fluence / Depth
Laser Nd:YAG cooled Module
2
2 10 msec 1 30-450 J/cm
2
Cooled Long Pulse 1064nm 6 15, 45, 60 msec 1 30-150 J/cm
Nd:YAG 1064
Nd:YAG 10 15 msec 1 20-50 J/cm 2
2
5x5 Pixel 10 msec 1 3–25 J/cm
2
Cooled Long Pulse 1320nm 6 30, 40, 50 msec 1 5-40 J/cm
Nd:YAG 1320
Nd:YAG 5x5 2
Pixel 30, 40, 50 msec 1 1-11 J/cm
Laser Nd:YAG non cooled Module

1064 1,2,3,4,5,6 20 nsec 1,2,4

Q-Switched
Q-Switched 1064nm Nd:YAG Nd:YAG 1064 5x5 Pixel 20 nsec 1,2,4 600-1200 mJ/p
532 2, 3, 4 KTP 20 nsec 1,2,4
1064 1,2,3,4,5,6 20 nsec 1,2,4
5x5
1064 Pixel 20 nsec 1,2,4
High Power Q-Switched Q-Switched
1064nm Nd:YAG Nd:YAG 532 2,3,4 mm KTP 20 nsec 1,2,4 600-1200 mJ/p
1064 5X5 Roller
20 nsec N/A
1064 7x1 Roller

Harmony XL Pro /SE System Service Manual 4-12

 System Description
Waveleng Pulse Energy Density /
Module Technology Spot size(mm) Pulse Width
th (nm) Frequency (Hz) Fluence / Depth
Laser Nd:YAG not cooled modules (Cont.)
2
2 10 msec 1 30-450 J/cm
2
Long Pulse 1064nm Nd:YAG Nd:YAG 1064 6 15, 45, 60 msec 1 30-150 J/cm
2
10 15 msec 1 20-50 J/cm
2
5x5 Pixel 10 msec 1 3 – 25 J/cm
2
Long Pulse 1320nm Nd:YAG Nd:YAG 1320 6 30, 40, 50 msec 1 5-40 J/cm
5x5 Pixel 30, 40, 50 msec 1 1-11 J/cm2
1 0.1-3.0 msec 10, 30 100-200 mJ/p
2
Fungus 1064nm Nd:YAG Nd:YAG 1064 2 10 msec 1 30-450 J/cm
2
6 15, 45, 60 msec 1 30-150 J/cm
Q-Switched 20 nsec
1064 1,2,3,4,5,6 1,2,4 600-1200 mJ/p
Nd:YAG
Q-Switched Pixel 1064nm FD Q-Switched 20 nsec
1064/5322, 3, 4 mm KTP 1,2,4 600-1200 mJ/p
Nd:YAG Nd:YAG
Q-Switched
1064 5x5 Pixel 20 nsec 1,2,4 600-1200 mJ/p
Nd:YAG
Laser Er:YAG not cooled modules
1 Short: 200-1200 mJ/p
Stack: 4
4 Medium: 600-1800 mJ/p
Short - 1 msec Non-stack: 2
iPixel
Er Scanner 2940nm
Nd:YAG
Er:YAG 2940 7x7 Pixel Medium - 1.5 msec Long: 800-2500 mJ/p
Long - 2 msec Short: 200-600 mJ/p
7x1 Scanner N/A Medium: 300-800 mJ/p
Long: 400-1000 mJ/p
Laser Er:Glass cooled modules
4 mm
Er:Glass 1540nm Er:Glass 1540 30, 40, 50 msec 1,2,3 300 – 1000 mJ/P
7 x 7 Pixel

Harmony XL Pro /SE System Service Manual 4-13

 System Description

4.4.1. Operation and Control Specifications

System Control
Fully computerized, microprocessor based

Graphic User Interface

High-resolution, color LCD display
Touch-screen technology

Laser Emission Indicators

Visual, illuminating yellow indicator:
OFF when no lasing occurs
Blinking during Ready mode
Illuminating continuously during laser emission
Audible indicator
Activated during laser emission, when pressing the operation buttons (user-
controlled) and upon detection of an error condition

4.4.2. Electrical Requirements

120 VAC, 20A, 50/60 Hz.
230 VAC, 10A, 50/60 Hz.

Note
Isolation from supply mains is provided by mains plug or circuit breaker.

4.4.3. Physical
System Dimensions (W x D x H)
44 x 54 x 125 cm
17 x 21 x 49 inches

Weights
Total: 60 kg. / 133 lbs.
Upper unit: 15 kg. / 33 lbs.
Lower unit: 45 kg. / 100 lbs.

Harmony XL Pro /SE System Service Manual 4-14

 System Description

4.4.4. Classifications
CDRH Laser Classification according to 21CFR 1040.10
Class IV

Laser Classification according to EN 60825-1

Class 4

Non-laser light source equipment Classification according to IEC 60601-2-57

Risk Group 3

Mode of Protection against Electric Shock

Class I Equipment

Degree of Protection against Electric Shock

Type B or BF Applied Part

4.4.5. Main (Upper) Unit

The upper unit includes the following components: Control Panel, Interface
Controller Board, Service Panel, Switching Module, Dump Card, Power Supplies,
PIC Controller, Impact generator, impact 48VDC power supply and iPixel
Scanner control card.
The Control Panel,
XL
The Harmony system is controlled by state of the art microprocessor and the
control of system parameters is done by the 8'' color LCD touch screen in the
front panel.
Interface Controller Board,
This is the microcontroller unit that controls the system, it controls the
following parts:
Digital I/O: o
Buzzer
o Yellow Lamp
o Key Switch o
Interlock
o FootSwitch
o Cap Charger inhibit
o Discharge
o Simmer Status

Harmony XL Pro /SE System Service Manual 4-15

 System Description

o Leakage Status
o IGBT Trigger
o Scanner board
o Flow Switch
o Thermal Switch
o Level Switch
o RS232 interface with LCD touch screen
All analog I/O:
o Charge voltage control
o Charge voltage monitor
o Tip ID.

Figure 4-8: Interface Controller

4.4.5.1. Service Panel Upper Unit

This panel includes:
1. Remote Interlock Connection, this interlock designed to
interrupt emission whenever the room door is opened.
2. The Footswitch Connection.
3. Units Lock knob.

Caution
If the system is in READY mode, pulse light emission occur
when the footswitch is pressed

Harmony XLPro System Service Manual 4-16