F-06/02

ACCREDITATION Issue Date: 18/08/2020

Rev. No: 09
DOCUMENT
LAB 036

Accreditation No: LAB 036

Awarded to

APPLIED PHYSICS COMPUTERS AND INSTRUMENTATION

CENTRE (APC&IC)
Pakistan Council of Scientific & Industrial Research (PCSIR)
Laboratories Complex. Lahore 54600, Pakistan.

The scope of accreditation is in accordance with the standard specifications

outlined in the following page(s) of this document. The accredited scope shall be
visible and legible in areas such as customer service, sample-receiving section etc
and shall not mislead its users.

The accreditation was first time granted on 24-08-2006 by Pakistan National

Accreditation Council.

The laboratory complies with the requirements of ISO/IEC 17025:2017.

The accreditation requires regular surveillance, and is valid until 16-06-2022.

The decision of accreditation made by Pakistan National Accreditation Council

implies that the organization has been found to fulfill the requirements for
accreditation within the scope.

The organization however, itself is responsible for the results of performed

measurements/tests.

PAKISTAN NATIONAL ACCREDITATION COUNCIL

14-09-2020 ____________________________
Date Director General

Page 1 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

Calibration Laboratory.

Accreditation Scope of APPLIED PHYSICS COMPUTERS AND INSTRUMENTATION

CENTRE (APC&IC)
Pakistan Council of Scientific & Industrial Research (PCSIR) Laboratories Complex.
Lahore 54600, Pakistan.

Permanent laboratory premises X

Field of Measurement:
*Expanded Uncertainty Technique, Reference
Measured quantity Range
(+ ) Standard, Equipment
Volume Measures (ASTM E-542)

Pipettes Cal.Lab-M25 Class F2

Burettes 0.01 mL to 100 0.0010 mL- 0.50 mL Weighing Scale
mL
Cal.Lab-M24 Class E2
Measuring Cylinders 1 mL to 2000 mL 0.010 mL - 10 mL
Weighing Scale
Measuring Beakers/
10 L to 2000 mL 0.10 mL - 5 mL Cal.Lab-M24 Class E2
Flasks/jugs
1 L to 5 L 0.0050 L to 0.050 L Weighing Scale
Cal.Lab-M25 Class F2
Micro Pipettes 10 µL to 1000 µL 0.60 µL to 10 µL Weighing Scale

Masses and Weighing Balances

Weighing Scales Up to 200 g 0.00010 g E2 Class Mass(Cal-Lab-24)
Up to 500 g 0.0010 g
Weighing Scales E2 Class
Class I and Below Mass(Cal-Lab-24)
Accuracy Classes
Up to 20 kg 0.00010 kg F2 Class Mass(Cal-Lab-26)
1 mg to 200 0.060 mg E2 Class Mass(Cal-Lab-24)
Masses
mg
F2 Class Mass(Cal-Lab-26)
NIMT CP-301
500 g to 20 0.00010 kg &Cal-Lab-32
F1 Class & Below
kg
Temperature Measurement
Reference Thermometer with
-50 oC to 350 oC 0.20 oC
Digital Thermometer RTD Probe (CAL. Lab-T17),
350 oC to 600 oC 0.30 oC
EURAMET cg-13 & 8 Precision Thermometer with k-
600 oC to 800 oC 1.0 oC
type Thermocouple (Cal. Lab-

14-09-2020 ____________________________
Date Director
Page 2 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

T34 & T2), Temperature

Controllers (Cal. Lab-TC1, TC2
& TC3), Dry Well Calibrator
(Cal. Lab-T16)
Reference Thermometer with
RTD Probe (CAL. Lab-T17),
Liquid in glass -50 oC to 100 oC 0.20 oC
Precision Thermometer with k-
Thermometer 100 oC to 350 oC 1.0 oC
type Thermocouple (Cal. Lab-
EA-10/11 & 13
T34 & T2), Dry Well Calibrator
(Cal. Lab-T16)
Reference Thermometer with
RTD Probe (CAL. Lab-T17),
Precision Thermometer with k-
-50 oC to 350 oC 0.20 oC
Digital Thermometer type Thermocouple (Cal. Lab-
350 oC to 600 oC 0.30 oC
EURAMET cg-13 & 8 T34 & T2), Temperature
600 oC to 800 oC 1.0 oC
Controllers (Cal. Lab-TC1, TC2
& TC3), Dry Well Calibrator
(Cal. Lab-T16)
Temperature Source
Reference Thermometer with
Dry Block Calibrator /
-50 oC to 100 oC o
0.20 C RTD Probe (CAL. Lab-T17),
Temperature
100 oC to 600 oC 0.80 oC Precision Thermometer with k-
Calibrator
type Thermocouple (Cal. Lab-
EURAMET cg-13 & 8
T34 & T2),
Reference Thermometer with
RTD Probe (CAL. Lab-T17),
Precision Thermometer with k-
Environmental -40 oC to 100 oC 0.20 oC
type Thermocouple (Cal. Lab-
Cahmbers 100 oC to 300 oC 0.80 oC
T34 & T2), Temperature
EA-10/08
Controllers (Cal. Lab-TC1, TC2
& TC3)

200 oC to 1000 Precision Thermometer with k-

Muffle Furnace o 1.0 oC
C type Thermocouple (Cal. Lab-
EA-10/08
T34 & T2
Temperature Measurement by Simulation Method (EURAMET cg-11)
-100 oC to 800 oC 0.20 oC Fluke 8508A Reference
RTD Pt 100
Multimeter (Cal. Lab- E67)
-200 oC to 1200
Thermocouple Type o 0.20 oC to 1.0 oC
C
“k” Portable Calibrator (Cal. Lab-
E2), Fluke 8508A Reference
-200 oC to 1200
Thermocouple Type o 0.20 oC to 1.0 oC Multimeter (Cal. Lab- E67)
C
“J”
Pressure
Pressure Gauge 2 psi to 250 psi 0.30 psi Pressure Calibrator (Cal.Lab-
Pneumatic P30)
14-09-2020 ____________________________
Date Director
Page 3 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

Pressure Gauge 500 psi to 8000 12 psi Dead Weight Tester

Hydraulic (Cal.Lab-P17& Pressure
psi Gauge (Cal.Lab-P27)

Vacuum Gauge 20 mm of Hg to 12 mm of Hg Vacuum Gauge (Cal.Lab-P3)

700 mm of Hg
Dimensional Measure
Line Length Standard 1 cm to 100 0.10 cm Line Length Standard
cm (Cal.Lab-L2)
Measuring Tape 5 cm to 500 cm 0.10 cm Measuring Tape (Cal.Lab-L5)

Vernier Caliper 0.5 mm to 300 0.010 mm Mitutoyo Gauge Block Set

mm (Cal.Lab-L11 & Cal.Lab-
L13)
Outside Micrometer 0.5 mm to 25 0.0010 mm Mitutoyo Gauge Block Set
mm (Cal.Lab-L11 & Cal.Lab-
L13)
Gauge Blocks 0.5 mm to 100 0.40 µm Mitutoyo Gauge Block Set
mm and Tesa Tronic Amplifier
(Cal.Lab-L11, Cal.Lab-L13
& Cal.Lab-L12)
Frequency Generation

10 Hz to 100 0.010 Hz to Cal.Lab-f6 Universal Frequency

Frequency Hz 0.020 Hz Counter,

1 KHz to 100 0.00030 KHz Cal.Lab-f2 Frequency Counter,

KHz
Cal.Lab-f3 Digital Oscilloscope
1 MHz to 50 0.0000030 MHz to 0.00010
MHz MHz

Frequency Measurement

14-09-2020 ____________________________
Date Director
Page 4 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

Frequency 10 Hz to 100 0.040 Hz to Cal.Lab-f6 Universal Frequency

Hz 0.10 Hz Counter,

1 KHz to 100 0.0010 KHz to 0.10 KHz Cal.Lab-f2 Frequency Counter,

KHz
Cal.Lab-f3 Digital Oscilloscope
0.0010 MHz to 0.010 MHz
1 MHz to 50
MHz

RPM Measurement

30 RPM to 0.50 RPM to 50 RPM Cal.Lab-f1 Function Generator,

Tachometers 30000 RPM

Cal.Lab-f6 Universal Frequency

Counter,

Cal.Lab-f7 & f8 Digital

Tachometers

Time Interval Measurement

Cal.Lab-f1 Function Generator,
Cal.Lab-f2 Frequency Counter,
Stop Watch
10 s to 7200 s + 0.52 s Cal.Lab-t1 & t2 Stop Watches,

Cal.Lab-f1 Function Generator,

Timer Cal.Lab-f2 Frequency Counter,
10 s to 7200 s + 1s
Cal.Lab-t1 & t2 Stop Watches,

Electrical Parameters (Generation & Source) – Calibrator

100 mV to 100 0.0090 mV to
mV 0.0020 V
AC Voltage Cal.Lab-E67
@ 50 Hz 1 V to 100 V 0.00020 V to Fluke 8508A
0.0010 V Reference Multimeter
100 V to 1000 V 0.0010 V to
0.10 V
1mV to 100 mV 0.0020 mV to
0.0030 mV Cal.Lab-E67
Fluke 8508A
DC Voltage
1 V to 100 V 0.0020 V to Reference Multimeter
0.0010 V

100 V to 1000 V 0.0010 V to

14-09-2020 ____________________________
Date Director
Page 5 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

0.100 V
AC Current Cal.Lab-E67
0 mA to 100 mA 0.001 mA to
@ 50 Hz Fluke 8508A
1 A to 10 A 0.0040 A
Reference Multimeter
0.0040 to 0.010 A
1 mA to 100 Cal.Lab-E67
DC Current 0.001 mA to
mA Fluke 8508A
0.010 A
1 A to 10 A Reference Multimeter
0.00040 to 0.0040 A
Electrical Parameters (Measurement) – Multimeter

10 V to 100 V 0.0010 V to Cal.Lab-E67

AC Voltage 0.010 V Fluke 8508A
@ 50 Hz Reference Multimeter
100 V to 1000 V 0.010 V to Cal.Lab-E65
0.10 V Inmol Calibrator

0.0020 mV to
1mV to 100 mV 0.010 mV Cal.Lab-E67
Fluke 8508A
1 V to 100 V 0.0040 V to Reference Multimeter
DC Voltage
0.0020 V Cal.Lab-E65
Inmol Calibrator
100 V to 1000 V 0.0020 V to
0.10 V

Cal.Lab-E67
Fluke 8508A
AC Current
1 mA to 100 0.0020 mA to Reference Multimeter
@ 50 Hz
mA 0.032 A Cal.Lab-E65
1 A to 10 A 0.0010 to 0.010 A Inmol Calibrator
Cal.Lab-E13 & E 16
Clamp Meter
Cal.Lab-E67
Fluke 8508A
AC Current (Clamp on)
Reference Multimeter
@ 50 Hz
5 A to 800 A 0.50 A to 2.0 A Cal.Lab-E65
Inmol Calibrator
Cal.Lab-E13 & E 16
Clamp Meter
Cal.Lab-E67
Fluke 8508A
2 mA to 100 0.001 mA to Reference Multimeter
DC Current
mA 0.0030 A Cal.Lab-E65
1 A to 10 A 0.0010 to 0.010 A Inmol Calibrator
Cal.Lab-E13 & E 16
Clamp Meter

14-09-2020 ____________________________
Date Director
Page 6 of 7
 F-06/02
ACCREDITATION Issue Date: 18/08/2020
Rev. No: 09
DOCUMENT
LAB 036

Cal.Lab-E67
Fluke 8508A
DC Current
Reference Multimeter
(Clamp on)
5 A to 800 A 0.50 A to 2.0 A Cal.Lab-E65
Inmol Calibrator
Cal.Lab-E13 & E 16
Clamp Meter
Resistance
1  - 100  0.0010  to 0.0020 G Cal.Lab-E67
Fluke 8508A
0.00020 k to 0.10 k Reference Multimeter
1 K - 100 K Cal.Lab-E55
Resistance 0.0010 M to 0.010 Milli Ohm Meter
M Cal.Lab-E69
1 M to 10 M Insulation Tester
0.10 M to 0.50 M Cal.Lab-E11 & E 21
Standard Resistances
10 M to 100 M
Power (Single Phase)
U.ID#(LLC/APCIC/PCP/01)
AC Power 10 W to Technique: Direct comparison
@ 50 Hz 5000 0.040 W to 3.0 W Stabilized Power Source,
W Power Meter, Digital
Multimeter
Spectrophotometer
Spectrophotometer

Wavelength Accuracy 525.5 nm 1 nm

37.5%T U.ID#(LLC/APCIC/SCP/01)
SS-1 Spectronic Standard Filters
Transmittance 10.2%T 0.01 to 0.03 %T Thermo Spectronics USA
@ 590nm 10.4 %T

Absorbance 0.990 Abs 0.01to 0.040 Abs

@ 590nm 0.997 Abs

* Expanded Uncertainty:
 Expanded Uncertainty is the measurement uncertainty at a coverage probability of 95 %,
which usually requires the use of a coverage factor of k = 2. This measurement
uncertainty is a value for which the laboratory has been accredited using the procedure
that was the subject of assessment. In certificates issued under its accreditation scope an
accredited laboratory is not permitted to quote an uncertainty that is smaller than the
published uncertainty for respective ranges as given above.

14-09-2020 ____________________________
Date Director
Page 7 of 7