DRIVER CONTROLS

SECTION DEF DEFOGGER

B

E
CONTENTS
BASIC INSPECTION .................................... 3 REAR WINDOW DEFOGGER POWER SUP- F
PLY AND GROUND CIRCUIT .......................... 17
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Description ...............................................................17

cardiagn.com
Work Flow ................................................................. 3 Component Function Check ....................................17 G
Diagnosis Procedure ...............................................17
FUNCTION DIAGNOSIS ............................... 4 Component Inspection .............................................18
REAR WINDOW DEFOGGER SYSTEM ............. 4 DRIVER SIDE DOOR MIRROR DEFOGGER ... 19 H
System Diagram ........................................................ 4
Description ...............................................................19
System Description ................................................... 4
Component Function Check ....................................19
Component Parts Location ........................................ 4 I
Diagnosis Procedure ...............................................19
Component Description ............................................. 5
Component Inspection .............................................20
DIAGNOSIS SYSTEM (BCM) ............................. 6 PASSENGER SIDE DOOR MIRROR DEFOG-
J
COMMON ITEM ........................................................... 6 GER ................................................................... 21
COMMON ITEM : CONSULT-III Function (BCM - Description ...............................................................21
COMMON ITEM) ....................................................... 6 Component Function Check ....................................21
Diagnosis Procedure ...............................................21 K
REAR WINDOW DEFOGGER ..................................... 6 Component Inspection .............................................22
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) ...................... 6 REAR WINDOW DEFOGGER ON SIGNAL ..... 23 DEF
DIAGNOSIS SYSTEM (IPDM E/R) ...................... 8 WITH AUTO A/C ........................................................23
Diagnosis Description ............................................... 8 WITH AUTO A/C : Description ................................23
CONSULT - III Function (IPDM E/R) ....................... 10 WITH AUTO A/C : Component Function Check ......23 M
WITH AUTO A/C : Diagnosis Procedure .................23
COMPONENT DIAGNOSIS ......................... 13
WITHOUT AUTO A/C ................................................23
N
REAR WINDOW DEFOGGER SWITCH ............13 WITHOUT AUTO A/C : Description .........................23
WITHOUT AUTO A/C : Component Function
WITH AUTO A/C ........................................................ 13 Check ......................................................................24
WITH AUTO A/C : Description ................................ 13 WITHOUT AUTO A/C : Diagnosis Procedure .........24 O
WITH AUTO A/C : Component Function Check .... 13
WITH AUTO A/C : Diagnosis Procedure ................. 13 ECU DIAGNOSIS ......................................... 25
WITHOUT AUTO A/C ................................................ 14 BCM (BODY CONTROL MODULE) ................. 25 P
WITHOUT AUTO A/C : Description ........................ 14 Reference Value ......................................................25
WITHOUT AUTO A/C : Component Function Wiring Diagram - DEFOGGER CONTROL SYS-
Check ...................................................................... 14 TEM (LHD MODELS) - ............................................41
WITHOUT AUTO A/C : Diagnosis Procedure ......... 15 Wiring Diagram - DEFOGGER CONTROL SYS-
WITHOUT AUTO A/C : Component Inspection ...... 16 TEM (RHD MODELS) - ...........................................45
Fail Safe ..................................................................48

DEF-1
 DTC Inspection Priority Chart .............................. 49 DRIVER SIDE DOOR MIRROR DEFOGGER
DTC Index .............................................................. 50 DOES NOT OPERATE. ..................................... 70
Diagnosis Procedure ............................................... 70
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ................. 51 PASSENGER SIDE DOOR MIRROR DEFOG-
Reference Value ..................................................... 51 GER DOES NOT OPERATE. ............................ 71
Wiring Diagram - DEFOGGER CONTROL SYS- Diagnosis Procedure ............................................... 71
TEM (LHD MODELS) - ........................................... 57
Wiring Diagram - DEFOGGER CONTROL SYS- REAR WINDOW DEFOGGER SWITCH DOES
TEM (RHD MODELS) - .......................................... 61 NOT LIGHT, BUT REAR WINDOW DEFOG-
Fail Safe ................................................................. 64 GER OPERATES ............................................... 72
DTC Index .............................................................. 66 Diagnosis Procedure ............................................... 72

SYMPTOM DIAGNOSIS ............................. 67 PRECAUTION ............................................ 73

REAR WINDOW DEFOGGER DOES NOT PRECAUTIONS ................................................. 73
OPERATE .......................................................... 67 Precaution for Supplemental Restraint System
Diagnosis Procedure .............................................. 67 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 73
REAR WINDOW DEFOGGER AND DOOR
MIRROR DEFOGGER DO NOT OPERATE. ..... 68 ON-VEHICLE MAINTENANCE .................. 74

cardiagn.com
Diagnosis Procedure .............................................. 68
PRE-INSPECTION FOR DIAGNOSTIC ............ 74
REAR WINDOW DEFOGGER DOES NOT Basic Inspection ...................................................... 74
OPERATE BUT BOTH OF DOOR MIRROR
DEFOGGER OPERATE. ................................... 69 ON-VEHICLE REPAIR ............................... 75
Diagnosis Procedure .............................................. 69 FILAMENT ......................................................... 75
Inspection and Repair ............................................. 75

DEF-2
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000000951256
B

DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM C
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
D
>> GO TO 2.
2.CHECK DTC E
Perform self diagnosis with CONSULT-III
Is any DTC detected?
YES >> Refer to BCS-61, "DTC Index". F
NO >> GO TO 3.
3.REPRODUCE THE MALFUNCTION INFORMATION

cardiagn.com
G
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
H
>> GO TO 4.
4.PERFORM “BASIC INSPECTION”
I
Perform the basic inspection.Refer to DEF-74, "Basic Inspection".

>> GO TO 5. J
5.IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms. K

>> GO TO 6.
DEF
6.IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
M
>> GO TO 7.
7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
N
Repair or replace the specified malfunctioning parts.

>> GO TO 8. O
8.FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3. P
Is the malfunctioning part repaired or replaced?
YES >> Trouble diagnosis is completed.
NO >> GO TO 4.

DEF-3
 REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
REAR WINDOW DEFOGGER SYSTEM
System Diagram INFOID:0000000000951258

cardiagn.com
JMLIA0030GB

System Description INFOID:0000000000951259

OPERATION DESCRIPTION
• BCM detects that the rear window defogger switch is turned ON when the ignition switch is ON, and then
transmits the rear window defogger switch signal to IPDM E/R via CAN communication for approximately 15
minutes.
• IPDM E/R turns rear window defogger relay ON when it receives the rear window defogger switch signal.
Then, it transmits the rear window defogger ON signal to ECM via CAN communication.
• The power is supplied to the rear window defogger and door mirror defogger (with mirror defogger) when the
rear window defogger relay is turned ON.

TIMER FUNCTION
• BCM transmits the rear window defogger switch signal to IPDM E/R for approximately 15 minutes when the
rear window defogger switch is turned ON with the ignition switch ON. Then, IPDM E/R operates the rear
window defogger and door mirror defogger (with mirror defogger).
• The timer is cancelled if the rear window defogger switch is pressed again during timer operation. BCM
stops the output of rear window defogger switch signal. The same reaction also occurs during timer opera-
tion if the ignition switch is turned OFF.
INPUT/OUTPUT SIGNAL CHART

Switch Input signal to BCM BCM function Acutuator

Rear window defogger switch Defogger switch signal Rear window defogger & Door mir- Rear window defogger
Ignition switch Ignition signal ror defogger* control Door mirror defogger *
*: With mirror defogger

Component Parts Location INFOID:0000000000951260

DEF-4
 REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >

cardiagn.com
G

JMLIA0031ZZ H
Rear window defogger switch (built
1. BCM M65,M66,M67 2. IPDM E/R E10,E12,E14 3.
in AUTO AMP. M53)
Rear window defogger switch (built in I
4. 5. Rear window defogger B58 6. Rear window defogger D155
heater control panel M54)
A. Behind glove box B. Engine room dash panel (LH) C. Behind back door trim finisher
J
Component Description INFOID:0000000000951261

K
• Operates the rear window defogger with the operation of rear window defogger
BCM switch.
• Performs the timer control of rear window defogger.

• Operates the rear window defogger and the door mirror defogger* with the control sig-
DEF
Rear window defogger relay
nal from IPDM E/R.
Auto amp. / Heter control panel • The rear window defogger switch is installed.
(Rear window defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger. M
• Heats the heating wire with the power supply from the rear window defogger relay to
Rear window defogger
prevent the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to N
Door mirror defogger* prevent the door mirror from fogging up.
*With mirror defogger
O

DEF-5
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001114950

APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-61, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification.
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.

cardiagn.com
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
PTC heater system PTC HEATER × ×

REAR WINDOW DEFOGGER

REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000000951263

Data monitor

DEF-6
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Monitor Item Description A

REAR DEF SW Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
B

ACTIVE TEST
C
Test Item Description
REAR DEFOGGER Give a drive signal to the rear window defogger relay to activate it.
D

cardiagn.com
G

DEF

DEF-7
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description INFOID:0000000001114954

Auto active test

Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan (LO, HI)
Operation procedure
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper

cardiagn.com
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4. Turn the ignition switch ON within 10 seconds. Then the horn sounds once and the auto active test starts.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system.
• Never start the engine.
Inspection in auto active test mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.

JPMIA0234ZZ

DEF-8
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >

Operation A
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test.
2 Rear window defogger 10 seconds B
3 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps C
4 10 seconds
• Tail lamps
• Front fog lamps
5 Headlamps LO ⇔ HI 5 times D
6 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
7 Cooling fan LO for 5 seconds → HI for 5 seconds
E
Concept of auto active test

cardiagn.com
G

JPMIA0235GB

• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto K
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode DEF

Symptom Inspection contents Possible cause

M
YES BCM signal input circuit

Perform auto active test. • Rear window defogger

Rear window defogger does not operate Does the rear window defog- • Rear window defogger ground circuit
ger operate? NO • Harness or connector between IPDM N
E/R and rear window defogger
• IPDM E/R
Any of the following components do not operate YES BCM signal input circuit O
• Parking lamps
• License plate lamps Perform auto active test. • Lamp or motor
• Tail lamps Does the applicable system • Lamp or motor ground circuit
• Front fog lamps operate? NO • Harness or connector between IPDM P
• Headlamp (HI, LO) E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R

DEF-9
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Symptom Inspection contents Possible cause
• Communication signal between BCM
and auto amp. (with auto A/C)
• Communication signal between BCM
and heater control panel (without auto
A/C, with manual A/C)
YES
• BCM
Perform auto active test. • CAN communication signal between
A/C compressor does not operate Does the magnet clutch oper- BCM and ECM
ate? • CAN communication signal between
ECM and IPDM E/R
• Magnet clutch
• Harness or connector between IPDM
NO
E/R and magnet clutch
• IPDM E/R
• Harness or connector between IPDM
E/R and oil pressure switch
YES
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal between
lamp blink? IPDM E/R and BCM

cardiagn.com
NO • CAN communication signal between
BCM and combination meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal between
ECM and IPDM E/R
• Cooling fan
• Cooling fan ground circuit
Perform auto active test. • Harness or connector between IPDM
Cooling fan does not operate E/R and cooling fan
Does the cooling fan operate?
• IPDM E/R
NO
• Cooling fan relay-3*
• Harness or connector between IPDM
E/R and cooling fan relay-3*
• Harness or connector between cooling
fan and cooling fan relay-3*
NOTE:
*: MR engine and K9K engine models

CONSULT - III Function (IPDM E/R) INFOID:0000000001114955

APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.

Diagnosis mode Description

Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC
Refer to PCS-30, "DTC Index".
DATA MONITOR
Monitor item

DEF-10
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >

Monitor Item MAIN A

Description
[Unit] SIGNALS
MOTOR FAN REQ Displays the value of the cooling fan speed signal received from ECM via CAN commu-
×
[1 - 4] nication.
B
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via CAN
×
[Off/On] communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN com- C
×
[Off/On] munication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN commu-
×
[Off/On] nication.
D
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN com-
×
[Off/On] munication.
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN com-
× E
[Off/On] munication.
HL WASHER REQ Displays the status of the headlamp washer request signal received from BCM via CAN
[Off/On] communication.
F
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN com-
×
[Stop/1LOW/Low/Hi] munication.

cardiagn.com
WIP AUTO STOP
× Displays the status of the front wiper auto stop signal judged by IPDM E/R. G
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
H
ST RLY REQ Displays the status of the ignition and starter request signal received from BCM via CAN
[Off/On] communication.
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R. I
[Off/On]
RR DEF REQ Displays the status of the rear defogger request signal received from BCM via CAN com-
×
[Off/On] munication.
OIL P SW
J
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
REV SW
Displays the status of the reverse switch judged by IPDM E/R.
[Off/On] K
Displays the status of the hood switch judged by IPDM E/R.
HOOD SW
NOTE:
[Off/On]
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system. DEF
Displays the status of the theft warning horn request signal received from BCM via CAN
THFT HRN REQ communication.
[Off/On] NOTE:
M
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system.
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
N
IGN ON SW
Displays the status of the ignition switch judged by IPDM E/R.
[Off/On]

ACTIVE TEST O
Test item

Test item Operation Description P

Off OFF
REAR DEFOGGER
On Operates the rear window defogger relay.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.

DEF-11
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Test item Operation Description
1 OFF
2 Operates the cooling fan relay (low operation).
MOTOR FAN
3
Operates the cooling fan relay (high operation).
4
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
Hi
ond intervals.
Fog Operates the front fog lamp relay.
HORN On Operates horn relay for 20 ms.

cardiagn.com

DEF-12
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
REAR WINDOW DEFOGGER SWITCH
WITH AUTO A/C
B
WITH AUTO A/C : Description INFOID:0000000000951265

The rear window defogger is operated by turning the rear window defogger switch ON. C
WITH AUTO A/C : Component Function Check INFOID:0000000000951266

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION D

Check (“REAR DEF SW”, “IGN ON SW”) in DATA MONITOR mode with CONSULT-III. Refer to DEF-6, "REAR
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".
E
When rear defogger switch is turned to ON
REAR DEF SW :ON
F
OK or NG
OK >> Rear window defogger switch is OK.

cardiagn.com
NG >> Refer to DEF-13, "WITH AUTO A/C : Diagnosis Procedure".
G
WITH AUTO A/C : Diagnosis Procedure INFOID:0000000000951267

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION H

1. Turn ignition switch ON.
2. Check voltage between BCM connector ground.
I
Terminal Voltage (V)
Connector Condition
(+) (–) (Approx.)

Rear window defogger switch is pressed. 0

J

K
M65 21 Ground
Rear window defogger switch is OFF.

DEF
JPMIA0154GB

Is the inspection result normal? M

YES >> Refer to GI-39, "Intermittent Incident".
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT HARNESS CONTINUITY N
1. Turn ignition switch OFF.
2. Disconnect BCM and auto amp. connector.
3. Check continuity between BCM connector and auto amp. connector. O

BCM connector Terminal Auto amp. connector Terminal Continuity

M65 21 M53 23 Yes P
4. Check continuity between BCM connector and ground.

BCM connector Terminal Continuity

Ground
M65 21 No
Is the inspection result normal?
YES >> GO TO 3.
DEF-13
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
NO >> Repair or replace harness between BCM and auto amp.
3.CHECK REAR WINDOW DEFOGGER SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect auto amp,connector.
3. Check continuity between auto amp. connector and ground.

Auto amp. connector Terminal Continuity

Ground
M53 17 Existed
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness between auto amp.and ground.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.

Terminal Voltage (V)

Connector
(+) (–) (Approx.)

cardiagn.com
M65 21 Ground

JPMIA0154GB

Is the inspection result normal?

YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK IINTERMITTENT INCDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace auto amp. Refer to VTL-21, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
6.CHECK IINTERMITTENT INCDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-64, "Exploded View".
NO >> Repair or replace the malfunctioning parts.
WITHOUT AUTO A/C
WITHOUT AUTO A/C : Description INFOID:0000000000978700

The rear window defogger is operated by turning the rear window defogger switch ON.
WITHOUT AUTO A/C : Component Function Check INFOID:0000000000978756

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

Check (“REAR DEF SW”, “IGN ON SW”) in DATA MONITOR mode with CONSULT-III. Refer to DEF-6, "REAR
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".

DEF-14
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >

When rear defogger switch is turned to ON A

REAR DEF SW :ON
OK or NG
B
OK >> Rear window defogger switch is OK.
NG >> Refer to DEF-13, "WITH AUTO A/C : Diagnosis Procedure".
WITHOUT AUTO A/C : Diagnosis Procedure INFOID:0000000000978757
C

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

1. Turn ignition switch ON. D
2. Check voltage between BCM connector ground.

Terminal (Wire color) Voltage (V) E

Connector Condition
(+) (–) (Approx.)

Rear window defogger switch is pressed. 0

F

cardiagn.com
M65 21 Ground
Rear window defogger switch is OFF. G

JPMIA0154GB
H

Is the inspection result normal?

YES >> Refer to GI-39, "Intermittent Incident".
I
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT HARNESS CONTINUITY
1. Turn ignition switch OFF. J
2. Disconnect BCM and heater control panel connector.
3. Check continuity between BCM connector and heater control panel connector.
K
Heater control
BCM connector Terminal Terminal Continuity
panel connector
M65 21 M54 18 Yes
DEF
4. Check continuity between BCM connector and ground

BCM connector Terminal Continuity M

Ground
M65 21 No
Is the inspection result normal?
YES >> GO TO 3. N
NO >> Repair or replace harness between BCM and heater control panel.
3.CHECK REAR WINDOW DEFOGGER SWITCH
O
Check rear window defogger switch.
Refer to DEF-16, "WITHOUT AUTO A/C : Component Inspection".
Is the inspection result normal? P
YES >> GO TO 4.
NO >> Replace heater control panel (rear window defogger switch). Refer to VTL-72, "Removal and
Installation".
4.CHECK REAR WINDOW DEFOGGER SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect heater control panel connector.
3. Check continuity between heater control panel connector and ground.
DEF-15
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >

Heater control panel connector Terminal Continuity

Ground
M54 20 Existed
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness between heater control panel and ground.
5.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.

Terminal Voltage (V)

Connector
(+) (–) (Approx.)

M65 21 Ground

cardiagn.com
JPMIA0154GB

Is the inspection result normal?

YES >> Refer to GI-39, "Intermittent Incident".
NO >> GO TO 6.
6.CHECK INTERMITTENT INCDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-64, "Exploded View".
NO >> Repair or replace the malfunctioning parts.
WITHOUT AUTO A/C : Component Inspection INFOID:0000000000997885

1.CHECK HEATER CONTROL PANEL (REAR WINDOW DEFOGGER SWITCH)

Check heter control panel (rear window defogger switch).

Terminal
Condition Continuity
Heater control panel
Rear window defogger switch is pressed Existed
18 20
Rear window defogger switch: OFF Not existed
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace heter control panel (rear window defogger switch). Refer to VTL-72, "Removal and Instal-
lation".

DEF-16
 REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
A
Description INFOID:0000000000951272

Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window B
from fogging up.
Component Function Check INFOID:0000000000951273

1.CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch D
ON.
Is the inspection result normal?
E
YES >> Rear window defogger is OK.
NO >> Refer to DEF-17, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000000951274
F

1.CHECK POWER SUPPLY CIRCUIT

cardiagn.com
1. Turn ignition switch ON. G
2. Check voltage between rear window defogger connector and ground.

Terminals H
(+) Condition of rear window Voltage (V)
(–) defogger switch (Approx.)
Rear window defogger
Terminal
connector I
ON Battery voltage
B58 1 Ground
OFF 0
J
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
K
2.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger connector. DEF
3. Check continuity between rear window defogger connector and ground.

Rear window defogger connector Terminal Continuity

Ground M
D155 2 Existed
Is the inspection result normal?
YES >> GO TO 4. N
NO >> Repair or replace harness between rear window defogger and ground.
3.CHECK HARNESS CONTINUITY
O
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and rear window defogger connectors.
3. Check continuity between IPDM E/R and rear window defogger connector.
P
IPDM E/R connector Terminal Rear window defogger connector Terminal Continuity
E14 49 B58 1 Existed
4. Check continuity between IPDM E/R connector and ground.

IPDM E/R connector Terminal Continuity

Ground
E14 49 Not existed

DEF-17
 REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness between IPDM E/R and rear window defogger .
4.CHECK FILAMENT
Check filament.
Refer to DEF-18, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair filament.
5.CHECK IPDM E/R OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R connector and ground.

Terminal Voltage (V)

Condition
(+) (–) (Approx.)

Rear window defogger switch : ON Battery voltage

49 Ground
Rear window defogger switch : OFF 0

cardiagn.com
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Replace IPDM E/R. Refer to PCS-32, "Removal and Installation".
Component Inspection INFOID:0000000000951275

1.CHECK FILAMENT
Check the filament for damage or blown.
Refer to DEF-75, "Inspection and Repair".
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Repair filament.

DEF-18
 DRIVER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
DRIVER SIDE DOOR MIRROR DEFOGGER
A
Description INFOID:0000000000951276

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
Component Function Check INFOID:0000000000951277

C
1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER
Check that heating wire of driver side door mirror defogger is heated when turning the rear window defogger
switch ON. D
Is the inspection result normal?
YES >> Driver side door mirror defogger is OK.
NO >> Refer to DEF-19, "Diagnosis Procedure". E

Diagnosis Procedure INFOID:0000000000951278

F
1.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.

cardiagn.com
2. Disconnect door mirror (driver side) connector. G
3. Turn ignition switch ON.
4. Check voltage between door mirror (driver side) connector and ground.

Terminals
H
Condition of rear win- Voltage (V)
(+)
(–) dow defogger switch (Approx.)
Door mirror (driver side) connector Terminal
I
D3(LHD) ON Battery voltage
7 Ground
D23(RHD) OFF 0
Is the inspection result normal? J
YES >> GO TO 2.
NO >> GO TO 3.
K
2.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (driver side) connector and ground. DEF

Door mirror (driver side) connector Terminal Continuity

D3(LHD) Ground
8 Existed M
D23(RHD)
Is the inspection result normal?
YES >> GO TO 4. N
NO >> Repair or replace harness between door mirror (driver side) and ground.
3.CHECK DOOR MIRROR HARNESS CONTINUITY
1. Turn ignition switch OFF. O
2. Disconnect IPDM E/R connector.
3. Check continuity between door mirror (driver side) connector and IPDM E/R.
P
Door mirror (driver side) connector Terminal IPDM E/R connector Terminal Continuity
D3(LHD)
7 E14 49 Existed
D23(RHD)
4. Check continuity between door mirror (driver side) connector and ground.

DEF-19
 DRIVER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >

Door mirror (driver side) connector Terminal Continuity

D3(LHD) Ground
7 Not existed
D23(RHD)
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident"
NO >> Repair or replace harness between door mirror (driver side) and IPDM E/R.
4.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER
Check driver side door mirror defogger.
Refer to DEF-20, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Replace door mirror (driver side). Refer to MIR-39, "Removal and Installation".
Component Inspection INFOID:0000000000951279

1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

1. Turn ignition switch OFF.
2. Disconnect door mirror (driver side) connector.

cardiagn.com
3. Check continuity between door mirror terminals.

Door mirror (diver side) connector Terminal Continuity

D3(LHD)
7 8 Existed
D23(RHD)
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace door mirror (driver side). Refer to MIR-39, "Removal and Installation".

DEF-20
 PASSENGER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
PASSENGER SIDE DOOR MIRROR DEFOGGER
A
Description INFOID:0000000000951280

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
Component Function Check INFOID:0000000000951281

C
1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
Check that the heating wire of passenger side door mirror defogger is heated when turning the rear window
defogger switch ON. D
Is the inspection result normal?
YES >> Passenger side door mirror defogger is OK.
NO >> Refer to DEF-21, "Diagnosis Procedure". E

Diagnosis Procedure INFOID:0000000000998568

F
1.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.

cardiagn.com
2. Disconnect door mirror (passenger side) connector. G
3. Turn ignition switch ON.
4. Check voltage between door mirror (passenger side) connector and ground.

Terminals
H

(+) Condition of rear win- Voltage (V)

(–) dow defogger switch (Approx.)
Door mirror (passenger side) con-
Terminal I
nector

D43(LHD) ON Battery voltage

7 Ground
D63(RHD) OFF 0 J
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3. K
2.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF. DEF
2. Check continuity between door mirror (passenger side) connector and ground.

Door mirror (passenger side) connector Terminal Continuity

Ground M
D43(LHD)
8 Existed
D63(RHD)
Is the inspection result normal?
N
YES >> GO TO 4.
NO >> Repair or replace harness between door mirror (passenger side) and ground.
3.CHECK DOOR MIRROR HARNESS CONTINUITY O
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between door mirror (passenger side) connector and IPDM E/R. P

Door mirror (passenger side) connector Terminal IPDM E/R connector Terminal Continuity
D43(LHD)
7 E14 49 Existed
D63(RHD)
4. Check continuity between door mirror (passenger side) connector and ground.

DEF-21
 PASSENGER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >

Door mirror (passenger side) connector Terminal Continuity

D43(LHD) Ground
7 Not existed
D63(RHD)
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace harness between door mirror (passenger side) and IPDM E/R.
4.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
Check passenger side door mirror defogger.
Refer to DEF-20, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Replace door mirror (passenger side). Refer to MIR-39, "Removal and Installation".
Component Inspection INFOID:0000000000951283

1.CHECK PASSENGER DOOR MIRROR DEFOGGER

1. Turn ignition switch OFF.
2. Disconnect door mirror (passenger side) connector.

cardiagn.com
3. Check continuity between door mirror terminals.

Door mirror (passenger side) connector Terminal Continuity

D43(LHD)
7 8 Existed
D63(RHD)
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace door mirror (passenger side). Refer to MIR-39, "Removal and Installation".

DEF-22
 REAR WINDOW DEFOGGER ON SIGNAL
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER ON SIGNAL
A
WITH AUTO A/C
WITH AUTO A/C : Description INFOID:0000000001025363
B
Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
WITH AUTO A/C : Component Function Check INFOID:0000000001025364
C
1.CHECK REAR WINDOW DEFOGGER ON SIGNAL
Check that the indicator lamps of rear window defogger switch are illuminated when turning the rear window D
defogger switch ON.
Is the inspection result normal?
OK >> Rear window defogger ON signal is OK. E
NG >> Refer to DEF-23, "WITH AUTO A/C : Diagnosis Procedure".
WITH AUTO A/C : Diagnosis Procedure INFOID:0000000001025365

F
1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

cardiagn.com
1. Turn ignition switch ON.
2. Check voltage between auto amp. connector ground. G

Terminal Voltage (V)

Auto amp. connector Condition
(+) (–) (Approx.) H
Rear window defogger switch is pressed. Battery voltage
M53 22 Ground
Rear window defogger switch is OFF. 0
I
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2. J
2.CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and auto amp. connector. K
3. Check continuity between IPDM E/R connector and auto amp. connector.

Auto amp. DEF

IPDM E/R connector Terminal Terminal Continuity
connector
E14 49 M53 22 Existed
4. Check continuity between BCM connector and ground. M

IPDM E/R connector Terminal Continuity

Ground
E14 49 Not existed N
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace harness between IPDM E/R and auto amp. O

3.CHECK IINTERMITTENT INCDENT

Check intermittent incident. P
Refer to GI-39, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace auto amp. Refer to VTL-21, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
WITHOUT AUTO A/C
WITHOUT AUTO A/C : Description INFOID:0000000001025367

DEF-23
 REAR WINDOW DEFOGGER ON SIGNAL
< COMPONENT DIAGNOSIS >
Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
WITHOUT AUTO A/C : Component Function Check INFOID:0000000001025368

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamps of rear window defogger switch are illuminated when turning the rear window
defogger switch ON.
Is the inspection result normal?
OK >> Rear window defogger ON signal is OK.
NG >> Refer to DEF-23, "WITH AUTO A/C : Diagnosis Procedure".
WITHOUT AUTO A/C : Diagnosis Procedure INFOID:0000000001025369

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

1. Turn ignition switch ON.
2. Check voltage between heater control panel connector ground.

Heater control Terminal (Wire color) Voltage (V)

Condition
panel connector (+) (–) (Approx.)

cardiagn.com
Rear window defogger switch is ON. Battery voltage
M54 19 Ground
Rear window defogger switch is OFF. 0
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and heater control panel connector.
3. Check continuity between IPDM E/R connector and heater control panel connector.

Heater control
IPDM E/R connector Terminal Terminal Continuity
panel connector
E14 49 M54 19 Existed
4. Check continuity between BCM connector and ground

IPDM E/R connector Terminal Continuity

Ground
E14 49 Not existed
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace harness between IPDM E/R and heater control panel.
3.CHECK IINTERMITTENT INCDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace heater control panel. Refer to VTL-72, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.

DEF-24
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001114994
B

VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
Ignition switch OFF OFF
ACC ON SW
Ignition switch ACC or ON ON D
A/C switch OFF OFF
AIR COND SW
A/C switch ON ON
E
Outside of the room is dark OFF
AUT LIGHT SYS
Outside of the room is bright ON
Lighting switch OFF OFF F
AUTO LIGHT SW
Lighting switch AUTO ON

cardiagn.com
Back door closed OFF
BACK DOOR SW G
Back door opened ON
BATTERY VOLT
NOTE: Approximately the same as power
Ignition switch ON H
Diesel engine models supply voltage
only
Driver's seat belt unfastened OFF
BUCKLE SW
Driver's seat belt fastened ON I
Door lock/unlock switch does not operate OFF
CDL LOCK SW
Press door lock/unlock switch to the LOCK side ON
J
Door lock/unlock switch does not operate OFF
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side ON
Passenger door closed OFF K
DOOR SW-AS
Passenger door opened ON
Driver door closed OFF
DOOR SW-DR DEF
Driver door opened ON
Rear LH door closed OFF
DOOR SW-RL
Rear LH door opened ON M
Rear RH door closed OFF
DOOR SW-RR
Rear RH door opened ON
N
Fan switch ON (when engine coolant is
cool)
NOTE: OFF
Depending on the ambient tempera- O
ture, battery voltage, etc.
ELEC PWR CUT The current status maintained with the
FREEZ
NOTE: signal from ECM received.
Diesel engine models
Engine running P
• Fan switch OFF
only
• Fan switch ON after engine warming
UP
NOTE: INHBT
Depending on the engine coolant
temperature, ambient temperature,
battery voltage, etc.

DEF-25
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
ENG COOLNT T
NOTE: Approximately the same as water
Engine running
Diesel engine models temperature gauge reading
only
ENGINE RPM
NOTE: Approximately the same as tachom-
Engine running
Diesel engine models eter reading
only
Engine stopped OFF
ENGINE RUN
Engine running ON
Engine stopped STOP
ENGINE STATUS
NOTE: While the engine stalls STALL
Diesel engine models Engine running RUN
only
At engine cranking CRA
Fan switch OFF OFF
FAN ON SIG
Fan switch ON ON
Front fog lamp switch OFF OFF

cardiagn.com
FR FOG SW
Front fog lamp switch ON ON
Front washer switch OFF OFF
FR WASHER SW
Front washer switch ON ON
Front wiper switch OFF OFF
FR WIPER LOW
Front wiper switch LO ON
Front wiper switch OFF OFF
FR WIPER HI
Front wiper switch HI ON
Front wiper switch OFF OFF
FR WIPER INT
Front wiper switch INT ON
Any position other than front wiper stop position OFF
FR WIPER STOP
Front wiper stop position ON
When hazard switch is not pressed OFF
HAZARD SW
When hazard switch is pressed ON
Lighting switch OFF OFF
HEAD LAMP SW 1
Lighting switch 2ND ON
Lighting switch OFF OFF
HEAD LAMP SW 2
Lighting switch 2ND ON
Lighting switch OFF OFF
HI BEAM SW
Lighting switch HI ON
Close the hood
NOTE: OFF
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood ON
NOTE:
H/L WASH SW OFF
The item is indicated, but not monitored
Ignition switch OFF or ACC OFF
IGN ON SW
Ignition switch ON ON
Ignition switch OFF or ACC OFF
IGN SW CAN
Ignition switch ON ON
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7

DEF-26
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
LOCK button of Intelligent Key is not pressed OFF
I-KEY LOCK
LOCK button of Intelligent Key is pressed ON
UNLOCK button of Intelligent Key is not pressed OFF B
I-KEY UNLOCK
UNLOCK button of Intelligent Key is pressed ON
Mechanical key is removed from key cylinder OFF
KEY ON SW
Mechanical key is inserted to key cylinder ON C
LOCK button of key fob is not pressed OFF
KEYLESS LOCK
LOCK button of key fob is pressed ON
D
UNLOCK button of key fob is not pressed OFF
KEYLESS UNLOCK
UNLOCK button of key fob is pressed ON
Light & rain sensor is in normal condition OK E
LIT-SEN FAIL
Light & rain sensor is with internal error NOTOK
• Ignition switch OFF or ACC
OFF F
OIL PRESS SW • Engine running
Ignition switch ON ON

cardiagn.com
OUT SIDE TEMP
NOTE: Ignition switch ON
Approximately the same as outside G
air temperature
Diesel engine models
Other than lighting switch PASS OFF
PASSING SW H
Lighting switch PASS ON
Return to ignition switch to LOCK position OFF
PUSH SW
Press ignition switch ON I
Rear window defogger switch OFF OFF
REAR DEF SW
Rear window defogger switch ON ON
J
RKE LOCK AND UN- NOTE: OFF
LOCK The item is indicated, but not monitored ON
Rear fog lamp switch OFF OFF K
RR FOG SW
Rear fog lamp switch ON ON
Rear washer switch OFF OFF
RR WASHER SW
Rear washer switch ON ON DEF
Rear wiper switch OFF OFF
RR WIPER INT
Rear wiper switch INT ON
M
Rear wiper switch OFF OFF
RR WIPER ON
Rear wiper switch ON ON
Rear wiper stop position OFF N
RR WIPER STOP
Other than rear wiper stop position ON
Ignition switch ON NOMAL
O
After the reception of air bag deployment signal from air bag diag-
OFF
SHOCK SENSOR nosis sensor unit
During the reception of air bag deployment signal from air bag diag-
ON P
nosis sensor unit
Lighting switch OFF OFF
TAIL LAMP SW
Lighting switch 1ST ON
When back door opener switch is not pressed OFF
TRNK OPNR SW
When back door opener switch is pressed ON

DEF-27
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
Turn signal switch OFF OFF
TURN SIGNAL L
Turn signal switch LH ON
Turn signal switch OFF OFF
TURN SIGNAL R
Turn signal switch RH ON

NOTE: OFF
UNLOCK WITH DR
The item is indicated, but not monitored ON
Other than the following OFF
UNLOCK SHOCK
During the unlock operation interlocked with air bag ON
VEHICLE SPEED While driving Equivalent to speedometer reading

cardiagn.com

DEF-28
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
A

cardiagn.com
G

DEF

N
JPMIA0145GB

PHYSICAL VALUES O
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter- P
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT -III. Refer to
BCS-26, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-7, "System
Description".

DEF-29
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

Terminal No. Description

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT
1 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(P) OUTPUT 1 switch Any of the condition below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 JPMIA0160GB

• Wiper intermittent dial 6 9.1 V

• Wiper intermittent dial 7
All switch OFF 0V
Lighting switch 2ND
Lighting switch PASS

cardiagn.com
Combination
2 Combination switch switch Front fog lamp switch ON
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH
JPMIA0163GB

9.3 V
All switch OFF 0V
Lighting switch AUTO
Rear fog lamp switch OFF
Combination
3 Combination switch switch Front wiper switch MIST
Ground Output
(LG) OUTPUT 3 (Wiper intermit- Front wiper switch INT
tent dial 4)

Front wiper switch LO JPMIA0162GB

9.3 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4)
Rear wiper switch ON
(Wiper intermittent dial 4)
4 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Rear washer switch ON
(Wiper intermittent dial 4)
Any of the condition below
with all switch OFF
JPMIA0161GB
• Wiper intermittent dial 1
9.1 V
• Wiper intermittent dial 5
• Wiper intermittent dial 6

DEF-30
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF 0V
B
Lighting switch 1ST
Lighting switch 2ND
Combination
5 Combination switch switch Lighting switch HI C
Ground Output
(W) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH D
JPMIA0164GB

9.1 V

7 Door lock/unlock Door lock/un- Not pressed F

Ground
(P) switch (Lock) Output lock switch

cardiagn.com
JPMIA0154GB

1.2 V G
Pressed to the lock side 0V

8 Not pressed I
Ground Hazard switch Output Hazard switch
(LG)

JPMIA0154GB
J
1.3 V
Pressed 0V

9 Door lock/unlock Door lock/un- Not pressed DEF

Ground
(BR) switch (Unlock) Output lock switch

JPMIA0154GB
M
1.2 V
Pressed to the unlock side 0V
N

Not pressed O
12 Back door opener Back door
Ground Output
(P) switch opener switch

JPMIA0154GB P
1.2 V
Pressed 0V

DEF-31
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Ignition switch OFF or ACC 0V

13
Ground Shock detect sensor Input
(R) Ignition switch ON

JPMIA0155GB

6.0 V

14 Not pressed Battery voltage

Ground A/C switch Output A/C switch
(L/R) Pressed 0V

15 Not pressed Battery voltage

Ground Fan switch Output Fan switch
(LG/B) Pressed 0V
16
Ground Alarm link Input — —
(GR)

cardiagn.com
Ignition switch OFF or ACC Battery voltage

17 Light & rain sensor

Ground Output
(BR) serial link Ignition switch ON

JPMIA0156GB

8.7 V
ON 0V

18 Security indica-
Ground Security indicator Output Blinking
(SB) tor

JPMIA0014GB

10.3 V
OFF Battery voltage
19 Input/
— CAN-H — —
(L) Output
20 Input/
— CAN-L — —
(P) Output

21 Rear window defog- Rear window Not pressed

Ground Output
(SB) ger switch defogger switch

JPMIA0154GB

1.1 V
While pressing 0V

DEF-32
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

24 Door lock status indi- Door lock status ON Battery voltage

(GR)
Ground
cator
Output
indicator
B
OFF 0V

OFF (When rear door LH

25 Rear door closed)
Ground Rear door switch LH Input D
(GR) switch LH
PKID0924E

11.2 V
E
ON (When rear door LH
0V
opened)

cardiagn.com
OFF (When driver door
G
26 Driver door closed)
Ground Driver door switch Input
(R) switch
PKID0924E
H
11.2 V
ON (When driver door
0V
opened)
I

J
OFF (When passenger
27 Passenger door Passenger door door closed)
Ground Input
(BR) switch switch
K
PKID0924E

11.2 V
ON (When passenger
door opened)
0V DEF

OFF (When back door

Battery voltage
28 Back door closed)
Ground Back door switch Input M
(G) switch ON (When back door
0V
opened)

OFF (When rear door RH

29 Rear door closed) O
Ground Rear door switch RH Input
(LG) switch RH
PKID0924E

11.2 V P
ON (When rear door RH
0V
opened)
30
Ground Audio link Output — — —
(SB)

DEF-33
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.3 V

Front fog lamp switch ON

(Wiper intermittent dial 4)

JPMIA0167GB

1.3 V

cardiagn.com
31 Combination switch Combination Rear fog lamp switch ON
Ground Input
(BR) INPUT 5 switch (Wiper intermittent dial 4)

JPMIA0168GB

1.3 V

Rear wiper switch ON

(Wiper intermittent dial 4)

JPMIA0169GB

1.3 V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 6
• Wiper intermittent dial 7
JPMIA0196GB

1.3 V

DEF-34
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF C

JPMIA0165GB

1.4 V D

Lighting switch PASS

F
JPMIA0167GB

1.3 V

cardiagn.com
G

Combination
32 Combination switch switch
H
Ground Input Lighting switch 2ND
(G) INPUT 2 (Wiper intermit-
tent dial 4)

JPMIA0166GB
I
1.3 V

Front wiper switch INT

K

JPMIA0168GB

1.3 V DEF

Front wiper switch HI

N
JPMIA0196GB

1.3 V
O

DEF-35
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

JPMIA0165GB

1.4 V

Turn signal switch LH

JPMIA0167GB

1.3 V

cardiagn.com
Combination
33 Combination switch switch
Ground Input Turn signal switch RH
(V) INPUT 1 (Wiper intermit-
tent dial 4)

JPMIA0166GB

1.3 V

Front wiper switch LO

JPMIA0168GB

1.3 V

Front washer switch ON

JPMIA0196GB

1.3 V

DEF-36
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.4 V D

E
Lighting switch AUTO
(Wiper intermittent dial 4)
F
JPMIA0167GB

1.3 V

cardiagn.com
G

34 Combination switch Combination Lighting switch 1ST

H
Ground Input
(GR) INPUT 4 switch (Wiper intermittent dial 4)

JPMIA0166GB
I
1.3 V

Rear wiper INT

(Wiper intermittent dial 4) K

JPMIA0167GB

1.3 V DEF

M
Any of the condition below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 6 N
JPMIA0196GB

1.3 V
O

DEF-37
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.4 V

Lighting switch HI
(Wiper intermittent dial 4)

JPMIA0166GB

1.3 V

cardiagn.com
35 Combination switch Combination Lighting switch 2ND
Ground Input
(L) INPUT 3 switch (Wiper intermittent dial 4)

JPMIA0167GB

1.3 V

Rear wiper switch ON

JPMIA0169GB

1.3 V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3
JPMIA0196GB

1.3 V
Insert mechanical key into ignition key cylin-
Battery voltage
36 der
Ground Key switch Output
(V) Remove mechanical key from ignition key
0V
cylinder

37 Ignition switch OFF 0V

Ground ACC power supply Output
(R) Ignition switch ACC or ON Battery voltage

38 Ignition power sup- Ignition switch OFF or ACC 0V

Ground Output
(W/L) ply Ignition switch ON Battery voltage

DEF-38
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Just after Insert mechanical key
39 Input/ Insert mechanical key into ignition key cylin- B
Ground NATS antenna amp. into ignition key cylinder. Pointer
(P) Output der
of tester should move
Just after Insert mechanical key
40 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer C
(LG) Output der
of tester should move
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage
(V) ply D
After passing the interior room lamp battery
0V
42 Interior room lamp saver operation time
Ground Output
(V) power supply Any other time after passing the interior room
Battery voltage E
lamp battery saver operation time

43 Rear wiper switch OFF 0V

Ground Rear wiper motor Output
(L) Rear wiper switch ON Battery voltage F
Rear wiper stop position 0V

cardiagn.com
G

44 Ignition switch
Ground Rear wiper auto stop Output Any position other than
(L/W) ON
rear wiper stop position H

JPMIA0197GB
I
45 Back door lock actu- Back door Pressed Battery voltage (300ms)
Ground Output
(GR) ator opener switch Not pressed 0V
J
Turn signal switch OFF 0V

K
47 Ignition switch
Ground Turn signal LH Output
(G/Y) ON Turn signal switch LH
DEF

PKID0926E

6.5 V
M
Turn signal switch OFF 0V

N
48 Ignition switch
Ground Turn signal RH Output
(G/B) ON Turn signal switch RH
O

PKID0926E

6.5 V
P
Lighting switch Rear fog lamp switch OFF 0V
49 1ST and front
Ground Rear fog lamp Output
(Y) fog lamp switch Rear fog lamp switch ON Battery voltage
ON
51 Depress the brake pedal Battery voltage
(R/W)*1 Ground Stop lamp switch Output
(R)*2 Release the brake pedal 0V

DEF-39
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

52 Room lamp timer Interior room OFF Battery voltage

Ground Output
(R) control lamp ON 0V

53 Power window pow- OFF or ACC 0V

Ground Output Ignition switch
(L) er supply ON Battery voltage

54 Door lock/un- Pressed to the unlock side Battery voltage

Ground Door unlock (All) Output
(O) lock switch Pressed to the lock side 0V
55
Ground Ground — Ignition switch ON 0V
(B)
56 Pressed to the unlock side 0 V
Door lock/un-
(Y)*1 Ground Door lock (All) Output
lock switch Pressed to the lock side Battery voltage
(SB)*2
57 Battery power sup-
Ground Output Ignition switch OFF Battery voltage
(Y) ply
58 Power window pow-
Ground Output Ignition switch OFF Battery voltage

cardiagn.com
(P) er supply
When lock button of key fob or Intelligent Key
0V
59 is not pressed
Ground Super lock Output
(BR) When lock button of key fob or Intelligent Key
Battery voltage
is pressed

60 Door lock/un- Pressed to the unlock side Battery voltage

Ground Driver door unlock Output
(GR) lock switch Pressed to the lock side 0V
*1: With Intelligent Key system
*2: Without Intelligent Key system

DEF-40
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001114995

cardiagn.com
G

DEF

JCLWA0404GB

DEF-41
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0405GB

DEF-42
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
G

DEF

JCLWA0406GB

DEF-43
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0407GB

DEF-44
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001125403

cardiagn.com
G

DEF

JCLWA0408GB

DEF-45
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0409GB

DEF-46
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
G

DEF

JCLWA0410GB

DEF-47
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0411GB

Fail Safe INFOID:0000000001114996

Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.

DEF-48
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

Display contents of CONSULT Fail-safe Cancellation A

• Inhibits engine cranking
B2190: NATS ANTENNA AMP • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B
• Inhibits engine cranking
B2191: DIFFERENCE OF KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
C
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
• Inhibits engine cranking D
B2194: DISCORD BCM-I-KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
E
B2195: ANTI SCANNING • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2196: DONGLE NG • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC F
• Fuel cut (ECM)

cardiagn.com
REAR WIPER CONTROL
BCM detects a rear wiper stopping position according to a rear wiper auto stop signal. G
When a rear wiper auto stop signal is in the condition listed below, BCM stops power supply to rear wiper after
rear wiper is activated for five seconds.
H
Ignition switch Rear wiper switch Auto stop signal
Rear wiper stop position signal cannot be
OFF
ON input 5 seconds. I
ON The signal does not change for 5 seconds.
NOTE:
The above operation is repeated when operating the rear wiper switch one minute after the stop of the rear J
wiper caused by Fail-safe.
TURN SIGNAL LAMP CONTROL
K
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE: DEF
The blinking speed is normal while activating the hazard warning lamp.
LIGHT & RAIN SENSOR MALFUNCTION DETECTION FUNCTION
BCM controls the following items when LIGHT & RAIN sensor has a malfunction. M

Auto Light Control

Headlamp is turned ON.
N
Front Wiper Control
The condition just before the activation of Fail-safe is maintained until the front wiper switch is turned OFF.
DTC Inspection Priority Chart INFOID:0000000001114997 O

DEF-49
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

Priority DTC
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
• B2196: DONGLE NG

DTC Index INFOID:0000000001114998

NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter

cardiagn.com
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.

CONSULT display TIME Fail-safe Refer to

No DTC is detected.
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT 0 1 - 39 — BCS-32
U1010: CONTROL UNIT (CAN) 0 1 - 39 — BCS-33
• With Intelligent Key system SEC-33
B2190: NATS ANTENNA AMP CRNT PAST × • Without Intelligent Key system SEC-
174
• With Intelligent Key system SEC-35
B2191: DIFFERENCE OF KEY CRNT PAST × • Without Intelligent Key system SEC-
176
• With Intelligent Key system SEC-36
B2192: ID DISCORD BCM-ECM CRNT PAST × • Without Intelligent Key system SEC-
177
• With Intelligent Key system SEC-38
B2193: CHAIN OF BCM-ECM CRNT PAST × • Without Intelligent Key system SEC-
178
B2194: DISCORD BCM-I-KEY CRNT PAST × SEC-39
• With Intelligent Key system SEC-179
B2195: ANTI SCANNING CRNT PAST × • Without Intelligent Key system SEC-
179
• With Intelligent Key system SEC-41
B2196: DONGLE NG CRNT PAST × • Without Intelligent Key system SEC-
180

DEF-50
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
Reference Value INFOID:0000000001035893
B
VALUES ON THE DIAGNOSIS TOOL

Monitor Item Condition Value/Status C

Changes depending on engine
coolant temperature, air condition-
MOTOR FAN REQ Engine idle speed 1-3
er operation status, vehicle speed, D
etc.
A/C switch OFF Off
AC COMP REQ Engine running A/C switch ON E
On
(Compressor is operating)
Lighting switch OFF Off
TAIL&CLR REQ F
Lighting switch 1ST, 2ND or AUTO (Light is illuminated) On
Lighting switch OFF Off
HL LO REQ

cardiagn.com
Lighting switch 2ND or AUTO (Light is illuminated) On
G
Lighting switch OFF Off
HL HI REQ
Lighting switch HI (Light is illuminated) On
Front fog lamp switch OFF Off H
Lighting switch 2ND or
FR FOG REQ
AUTO (Light is illuminated) Front fog lamp switch ON On
Front washer switch OFF Off
I
Ignition switch ON, and low Front washer switch ON
HL WASHER REQ
beam headlamp is ON (When headlamp washer is operat- On
ing)
J
Front wiper switch OFF STOP
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO Low K
Front wiper switch HI Hi
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper DEF
ACT P
stop position
Front wiper operates normally Off
WIP PROT Ignition switch ON M
Front wiper stops at fail-safe oper-
BLOCK
ation

ST RLY REQ When Intelligent Key is outside the vehicle, and the push switch
Off N
NOTE: is pushed
Vehicle without Intelligent Key system indi- When Intelligent Key is inside the vehicle, and the push switch is
cates only “ON”, and it does not change. On
pushed
Ignition switch OFF or ACC Off O
IGN RLY
Ignition switch ON On
Rear window defogger switch OFF Off
P
RR DEF REQ Ignition switch ON Rear window defogger switch ON
(Rear window defogger is operat- On
ing)
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close

DEF-51
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
Except selector lever R position Off
REV SW
Selector lever R position On
HOOD SW Close the hood Off
NOTE:
This item is monitored only on the vehicle
with the Vehicle Security (Theft Warning) Open the hood On
system.
THFT HRN REQ Not operation Off
NOTE:
This item is monitored only on the vehicle
with the Vehicle Security (Theft Warning) Horn is activated with Vehicle Security (Theft Warning) system. On
system.
NOTE:
HORN CHIRP Off
This item is indicated, but not monitored.
Ignition switch OFF or ACC Off
IGN ON SW
Ignition switch ON On

cardiagn.com

DEF-52
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
A

cardiagn.com
G

DEF

N
JPMIA0236GB

PHYSICAL VALUES O

Terminal No. Description

(Wire color) Value
Input/ Condition
Signal name (Approx.) P
+ − Output
1
Ground Battery power supply Input Ignition switch OFF Battery voltage
(G)
2
Ground Battery power supply Input Ignition switch OFF Battery voltage
(R)
5
Ground Ground — Ignition switch ON 0V
(B)

DEF-53
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
6
Ground Ground — Ignition switch ON 0V
(B)

7 Front wiper switch OFF 0V

Ground Front wiper LO Output Ignition switch ON
(Y) Front wiper switch LO Battery voltage

8 Front wiper switch OFF 0V

Ground Front wiper HI Output Ignition switch ON
(Y/R) Front wiper switch HI Battery voltage
9
Ground ECM relay power supply Output Ignition switch ON Battery voltage
(G)

10*1 Ground ECM relay power supply Output Ignition switch ON Battery voltage
(L/R)

11*2 PTC heater OFF Battery voltage

Ground PTC heater 1 relay control Output
(O) PTC heater ON 0V

12*2 PTC heater OFF Battery voltage

Ground PTC heater 2 relay control Output
(G/Y) PTC heater ON 0V

cardiagn.com
14 Ignition switch OFF or ACC 0V
Ground Ignition power supply Output
(R/B) Ignition switch ON Battery voltage
• Engine running 0 - 1.0 V*1
• Ignition switch OFF
15 (For a few seconds after turning ignition switch
0.6 V*2
(Y/L)*1 Ground ECM relay control Input OFF)
(B/R)*2 Ignition switch OFF or ACC
(More than a few seconds after turning ignition Battery voltage
switch OFF)

16*3 Ignition switch ON Battery voltage

Ground Ignition relay power supply Output
(Y/R) Ignition switch OFF or ACC 0V

19*1 Ignition switch ON Battery voltage

Ground Ignition relay power supply Output
(R/O) Ignition switch OFF or ACC 0V

21*4 Close the hood Battery voltage

Ground Hood switch Input
(GR) Open the hood 0V
Ignition switch OFF or ACC 0V
• Selector lever “R”
(Except M/T models)
Battery voltage
• M/T control lever “R”
(M/T models)
22
Ground Reverse switch Input
(Y/G) Ignition switch ON • Selector lever in any po-
sition other than “R” (Ex-
cept M/T models)
0V
• M/T control lever in any
position other than “R”
(M/T models)
Engine stopped 0V
A/C switch OFF 0V
23
Ground A/C relay power supply Output
(Y/B) Engine running A/C switch ON
(A/C compressor is oper- Battery voltage
ating)

24 Lighting switch OFF 0V

Ground Headlamp LO (RH) Output
(R/Y) Lighting switch 2ND Battery voltage

DEF-54
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

25*1 Ignition switch OFF or ACC Battery voltage

Ground ETC relay control Input B
(G/L) Ignition switch ON 0 - 1.0 V
Front wiper stop position 0V
26
Ground Front wiper auto stop Input Ignition switch ON Any position other than C
(O) Battery voltage
front wiper stop position

27 Engine stopped 0V
Ground Oil pressure switch Input
(W) Engine running Battery voltage D
28 Input/
— CAN-H — —
(L) Output
29 Input/ E
— CAN-L — —
(P) Output

30*4 The horn is not activated Battery voltage

Ground Horn relay control Output
(L) The horn is activated 0V F

31 Lighting switch OFF 0V

Ground Headlamp LO (sensor) Output Ignition switch ON

cardiagn.com
(R) Lighting switch 2ND Battery voltage
G
32*1 Ground ETC relay power supply Output Ignition switch ON Battery voltage
(R/Y)
• Engine running H
• Ignition switch ON 0 - 1.0 V
33*1 (For 1 second after turning ignition switch ON)
Ground Fuel pump relay control Input
(B/O) Ignition switch ON
I
(More than 1 second after turning ignition switch Battery voltage
ON)

Ignition switch ON Selector lever “P” or “N” 0V

J
34 (Except M/T mod- Selector lever in any posi-
Ground Starter relay power supply Input els) Battery voltage
(R/B) tion other than “P” or “N”
Ignition switch ON (M/T models)
K
35 Ignition switch OFF or ACC 0V
Ground Ignition switch ON Input
(W/L) Ignition switch ON Battery voltage

36 Front fog lamp switch ON Battery voltage DEF

Ground Front fog lamp (RH) Output Lighting switch 1ST
(W) Front fog lamp switch OFF 0V

37 Lighting switch 1ST Battery voltage

Ground Parking lamp (RH) Output M
(R/W) Lighting switch OFF 0V

38 Tail, license plate lamps Lighting switch 1ST Battery voltage

Ground Output
(R/L) and illuminations Lighting switch OFF 0V N
When headlamp washer is
0V
39 Headlamp washer relay operating
Ground Output Ignition switch ON
(GR) control When headlamp washer is O
Battery voltage
not operating

40*1 Ignition switch OFF or ACC 0V

(BR/Y)* 5 Ground Ignition relay power supply Output P
Ignition switch ON Battery voltage
(SB)*6

41 Ignition switch OFF or ACC 0V

Ground Ignition relay power supply Output
(P) Ignition switch ON Battery voltage

DEF-55
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
• Ignition switch OFF or ACC
• Approximately 1 second or more after turning 0V
42*1 Fuel pump relay power the ignition switch ON
Ground Output
(B/Y) supply • Approximately 1 second after turning the igni-
tion switch ON Battery voltage
• Engine running

43 Front fog lamp switch ON Battery voltage

Ground Front fog lamp (LH) Output Lighting switch 1ST
(W/B) Front fog lamp switch OFF 0V

44 Lighting switch OFF 0V

Ground Headlamp LO (LH) Output
(L) Lighting switch 2ND Battery voltage
• Lighting switch 2ND and HI
45 Battery voltage
Ground Headlamp HI (RH) Output • lighting switch PASS
(L/W)
Lighting switch OFF 0V
• Lighting switch 2ND and HI
46 Battery voltage
Ground Headlamp HI (LH) Output • Lighting switch PASS
(G)

cardiagn.com
Lighting switch OFF 0V

47 Lighting switch 1ST Battery voltage

Ground Parking lamp (LH) Output
(R/L) Lighting switch OFF 0V

48*7 When cooling fan does HI operation 0V

Ground Cooling fan relay-3 control Output
(Y) When cooling fan does OFF or LO operation Battery voltage
Rear window defogger
Battery voltage
49 Rear window defogger re- switch ON
Ground Output Ignition switch ON
(B) lay power supply Rear window defogger
0V
switch OFF

50 When engine is clanking Battery voltage

Ground Starter relay power supply Output
(B/R) When engine is not clanking 0V

51 Ignition switch START Battery voltage

Ground Ignition switch START Input
(P) Ignition switch OFF, ACC or ON 0V

52 Cooling fan relay-1 power When cooling fan does LO or HI operation Battery voltage
Ground Output
(W) supply When cooling fan does OFF operation 0V
53 Battery power supply
Ground Input Ignition switch OFF Battery voltage
(W/B) (Cooling fan relay)

54*5 Cooling fan relay-2 power When cooling fan does HI operation Battery voltage
Ground Input
(R) supply When cooling fan does OFF or LO operation 0V

*1: HR engine and MR engine models

*2: K9K engine models
*3: Except M/T models only
*4: With vehicle security (theft warning) system
*5: HR engine models
*6: MR engine models
*7: MR engine and K9K engine models

DEF-56
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001125404

cardiagn.com
G

DEF

JCLWA0404GB

DEF-57
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0405GB

DEF-58
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
G

DEF

JCLWA0406GB

DEF-59
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0407GB

DEF-60
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001125405

cardiagn.com
G

DEF

JCLWA0408GB

DEF-61
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0409GB

DEF-62
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
G

DEF

JCLWA0410GB

DEF-63
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

cardiagn.com
JCLWA0411GB

Fail Safe INFOID:0000000001035895

CAN communication control

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If no CAN communication is available with ECM

DEF-64
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

Control part Fail-safe in operation A

1 2
• The cooling fan relay-2* or the cooling fan relay-3* turns ON when the ignition switch
Cooling fan is turned ON
• Turns off the fan motor low relay when the ignition switch is turned OFF B
A/C compressor A/C relay OFF
*1: HR engine models
*2: MR engine and K9K engine models C
If no CAN communication is available with BCM

Control part Fail-safe in operation

D

• The headlamp low relay turns ON when the ignition switch is turned ON
Headlamp • The headlamp low relay turns OFF when the ignition switch is turned OFF
• Headlamp high relay OFF E
• Parking lamps
• License plate lamps • The tail lamp relay turns ON when the ignition switch is turned ON
• Tail lamps • The tail lamp relay turns OFF when the ignition switch is turned OFF F
• Illuminations
• The status just before activation of fail-safe control is maintained until the ignition

cardiagn.com
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The front wiper is operated at LO speed until the ignition switch is turned OFF if the
G
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF H
Starter motor Inhibit relay OFF
Rear window defogger Rear window defogger relay OFF
I
Headlamp washer Headlamp washer relay OFF
PTC heater PTC heater relay OFF
J
Ignition relay malfunction detection function
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit. K
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
DEF
DTC Ignition switch Ignition relay Tail lamp relay
— ON ON —
— OFF OFF — M
B2098: IGN RLY ON OFF ON ON (10 minutes)
B2099: IGN RLY OFF ON OFF —
N
NOTE:
The tail lamp relay is turned OFF when the ignition switch is turned ON.

Front wiper control O

IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times. P
Ignition switch Front wiper switch Front wiper auto stop signal
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
ON
change for 10 seconds.
NOTE:
DEF-65
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
DTC Index INFOID:0000000001035896

CONSULT display Fail-safe TimingNOTE Reference page

No DTC is detected.
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT × CRNT PAST PCS-14
B2098: IGN RELAY ON × CRNT PAST PCS-15
B2099: IGN RELAY OFF — CRNT PAST PCS-16
B2100: EEPROM — CRNT PAST PCS-17
NOTE:
The details of time display are as follows.
• CRNT: The malfunctions that are detected now.
• PAST: The number is indicated when it is normal at present and a malfunction was detected in the past.

cardiagn.com

DEF-66
 REAR WINDOW DEFOGGER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
REAR WINDOW DEFOGGER DOES NOT OPERATE
Diagnosis Procedure INFOID:0000000000998574
B

1.IPDM E/R AUTO ACTIVE TEST

Check IPDM E/R active test. C
Refer to PCS-9, "Diagnosis Description".
Is the inspection result normal?
YES >> GO TO 2. D
NO >> Repair or replace the malfunctioning parts.
2.CHECK REAR WINDOW DEFOGGER SWITCH
E
Check rear window defogger switch.
With auto A/C. Refer to DEF-13, "WITH AUTO A/C : Component Function Check".
Without auto A/C. Refer to DEF-14, "WITHOUT AUTO A/C : Component Function Check"
Is the inspection result normal? F
YES >> GO TO 3.

cardiagn.com
NO >> Repair or replace the malfunctioning parts.
G
3.CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Check rear window defogger power supply and ground circuit.
Refer to DEF-17, "Component Function Check". H
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts. I

DEF

DEF-67
 REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
OPERATE.
Diagnosis Procedure INFOID:0000000000951289

1.IPDM E/R AUTO ACTIVE TEST

Check IPDM E/R active test.
Refer to PCS-9, "Diagnosis Description".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK REAR WINDOW DEFOGGER SWITCH
Check rear window defogger switch.
With auto A/C. Refer to DEF-13, "WITH AUTO A/C : Component Function Check".
Without auto A/C. Refer to DEF-14, "WITHOUT AUTO A/C : Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.

cardiagn.com

DEF-68
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
A
MIRROR DEFOGGER OPERATE.
Diagnosis Procedure INFOID:0000000000951290
B
1.CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Check rear window defogger power supply and ground circuit.
C
Refer to DEF-17, "Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident". D
NO >> Repair or replace the malfunctioning parts.

cardiagn.com
G

DEF

DEF-69
 DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
< SYMPTOM DIAGNOSIS >
DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
Diagnosis Procedure INFOID:0000000000951292

1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check driver side door mirror defogger.
Refer to DEF-19, "Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.

cardiagn.com

DEF-70
 PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
< SYMPTOM DIAGNOSIS >
PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
A
Diagnosis Procedure INFOID:0000000000951293

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER B

Check passenger side door mirror defogger.
Refer to DEF-21, "Component Function Check".
Is the inspection result normal? C
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
D

cardiagn.com
G

DEF

DEF-71
 REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WIN-
DOW DEFOGGER OPERATES
Diagnosis Procedure INFOID:0000000000951295

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check rear window defogger ON signal.
With auto A/C. Refer to DEF-23, "WITH AUTO A/C : Component Function Check".
Without auto A/C. Refer to DEF-24, "WITHOUT AUTO A/C : Component Function Check".
Is the inspection result normal?
YES >> Refer to GI-39, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.

cardiagn.com

DEF-72
 PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000000951296

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.

cardiagn.com
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H

DEF

DEF-73
 PRE-INSPECTION FOR DIAGNOSTIC
< ON-VEHICLE MAINTENANCE >
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic Inspection INFOID:0000000000977986

BASIC INSPECTION
1.INSPECTION START
1. Check the service history.
2. Check the following parts.
• Fuse/circuit breaker blown.
• Poor connection, open or short circuit of harness connector.
• Battery voltage.
Is the inspection result normal?
YES >> Inspection end.
NO >> Repair or replace the malfunctioning parts.

cardiagn.com

DEF-74
 FILAMENT
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR A
FILAMENT
Inspection and Repair INFOID:0000000000951297
B

INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg- C
ative probe. Then press the foil against the wire with your finger.

SEL122R F

2. Attach probe circuit tester (in Volt range) to middle portion of

cardiagn.com
each filament. G

SEL263

J
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil- K
ament. Test needle will swing abruptly when probe passes the
point.
DEF

SEL265

REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)

DEF-75
 FILAMENT
< ON-VEHICLE REPAIR >
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.

PIIA0215E

4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver

cardiagn.com
composition is deposited.
Do not touch repaired area while test is being conducted.

SEL012D

5. Apply a constant stream of hot air directly to the repaired area

for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.

SEL013D

DEF-76