0% found this document useful (0 votes)
103 views2 pages

Annexure - 1 Technical and General Specifications - Ambulance Technical Specifications

The document discusses the technical specifications for an ambulance to be procured by the Indian Institute of Science Education and Research Thiruvananthapuram. It provides details on the required engine capacity, power, torque, vehicle body dimensions, patient compartment dimensions, and other standard equipment. Some key requirements mentioned are a minimum payload capacity of 1100 kg, separate air-conditioned patient compartment of at least 2755mm in length and 1650mm in width, provision for an oxygen cylinder with flow meter and humidifier, roof-mounted warning lights and siren, and exterior design as per ARAI ambulance standards.

Uploaded by

Preeti
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
103 views2 pages

Annexure - 1 Technical and General Specifications - Ambulance Technical Specifications

The document discusses the technical specifications for an ambulance to be procured by the Indian Institute of Science Education and Research Thiruvananthapuram. It provides details on the required engine capacity, power, torque, vehicle body dimensions, patient compartment dimensions, and other standard equipment. Some key requirements mentioned are a minimum payload capacity of 1100 kg, separate air-conditioned patient compartment of at least 2755mm in length and 1650mm in width, provision for an oxygen cylinder with flow meter and humidifier, roof-mounted warning lights and siren, and exterior design as per ARAI ambulance standards.

Uploaded by

Preeti
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

भारतीय विज्ञान शिक्षा एिं अनस

ु ंधान संस्थान ततरुिनंतपरु म


(मानि संसाधन विकास मंत्रालय, भारत सरकार के तहत स्िायत्त संस्था)
INDIAN INSTITUTE OF SCIENCE EDUCATION AND RESEARCH THIRUVANANTHAP URAM
(An Autonomous Institution under MHRD, Government of India)
सी.ई. टी पररसर, ततरुिनंतपुर म /CET Campus, Thiruvananthapuram-695016
Tel: 0471-2597448 Fax : 2590498 E-mail: [email protected]

ANNEXURE - 1
TECHNICAL AND GENERAL SPECIFICATIONS – AMBULANCE
TECHNICAL SPECIFICATIONS
Emission Norms Bharat Stage III and above

Engine capacity in CC 2000 – 3000

Maximum power in HP 75-100

Torque in nm Above 200

Wheel base in mm Minimum of 3200

Fuel tank capacity Adequate to cover 300 KM without refuelling

Payload capacity Minimum 1100 Kgs

VEHICLE BODY DIMENSIONS

Overall length in mm Above 4900

Overall width in mm Above 1900

Overall height in mm Above 2200

Ground clearance in mm Above 200

PATIENT COMPARTMENT DIMENSIONS ( TO BE SEPERATED FROM DRIVER CABIN)

Length in mm Minimum 2755

Width in mm Minimum 1650

Height in mm Minimum 1800

Air condition Yes , should be air-conditioned

Seating Capacity Patient + 7

Other specifications As prescribed by ARAI as per code AIS 125 (Part I & II) & other
prevailing government regulations.

1/2
OTHER STANDARD EQUIPMENTS / ACCESSORIES
Stretcher Ordinary ( in the patient compartment as per ARAI
specifications)

Medicine Cabinet Inbuilt

Oxygen Oxygen cylinder cage with filled oxygen cylinder, flow meter,
humidifier with separate mask of adult and paediatric. The
agency should obtain the explosive certificate for oxygen
cylinder. The oxygen level as per standard level has to be
maintained by the agency at their cost.

IV Hook At three locations on top roof

Warning Lights Roof mounted as per ARAI specifications. Should have revolving
flashers and lights indicating emergency while transferring
serious patients.

Public Address System 100 W

Siren High Intensity roof mounted with five different tones to draw
public attention to make way in high density traffic

Exterior design / Painting As per the specifications for ambulances according to ARAI
standards and other government regulations.

Signature of the tenderer

2/2

You might also like