BLOWROOM

BASIC OPERATIONS

Basic operations in the blow-room:

1. Opening
2. Cleaning
3. Mixing or blending
4. Microdust removal
5. Uniform feed to the carding machine
6. Recycling the waste

Blow room installation consists of a sequence of different machines to carry out the above said
operations. Moreover Since the tuft size of cotton becomes smaller and smaller, the required intensities
of processing necessitates different machine configuration.

TECHNOLOGICAL POINTS IN BLOWROOM

 Opening in blow-room means opening into small flocks. Technological operation of opening
means the volume of the flock is increased while the number of fibres remains constant. i.e. the
specific density of the material is reduced.
 The larger the dirt particle , the better they can be removed.
 Since almost every blow-room machine can shatter particles, as far as possible a lot of impurities
should be eliminated at the start of the process. Opening should be followed immediately by
cleaning, if possible in the same machine.
 The higher the degree of opening, the higher the degree of cleaning. A very high cleaning effect
is almost always purchased at the cost of a high fibre loss. Higher roller speeds give a better
cleaning effect
but also more stress on the fibre.
 Cleaning is made more difficult if the impurities of dirty cotton are distributed through a larger
quantity of material by mixing with clean cotton.
 The cleaning efficiency is strongly dependent on the Trash %. It is also affected by the size of the
particle and stickiness of cotton. Therefore cleaning efficiency can be different for different
cottons with the
same trash %.
 There is a new concept called cleaning resistance. Different cottons have different cleaning
resistance.
 If cotton is opened well in the opening process, cleaning becomes easier because opened cotton
has more surface area, therefore cleaning is more efficient
 If automatic bale opener is used, the tuft size should be as small as possible and the machine
stop time should be reduced to the minimum level possible.
 If Manual Bale openers are used, the tuft size fed to the feed lattice should be as small as
possible
 Due to machine harvesting , cotton contains more and more impurities, which furthermore are
shattered by hard ginning. Therefore cleaning is always an important basic operation.
 In cleaning, it is necessary to release the adhesion of the impurities to the fibres and to give the
particles an opportunity to separate from the stock. The former is achieved mostly by picking of
flocks, the latter is
achieved by leading the flocks over a grid.
 Using Inclined spiked lattice for opening cotton in the initial stages is always a better way of
opening the cotton with minimum damages. Of course the production is less with such type of
machines.
But one should bear in mind that if material is recycled more in the lattice, neps may increase.
 Traditional methods use more number of machines to open and clean natural fibres.
 Mechanical action on fibres causes some deterioration on yarn quality, particularly in terms of
neps. Moreover it is true that the staple length of cotton can be significantly shortened.
 Intensive opening in the initial machines like Bale breaker and blending machines means that
shorter overall cleaning lines are adequate.
 In a beating operation, the flocks are subjected to a sudden strong blow. The inertia of the
impurities accelerated to a high speed, is substantially greater than that of the opened flocks due
to the low air resistance
of the impurities. The latter are hurled against the grid and because of their small size, pass
between the grid bars into the waste box, while the flocks continue around the periphery of the
rotating beater.
 By using a much shorter machine sequence, fibres with better elastic properties and improved
spinnability can be produced.
 Air streams are often used in the latest machine sequence, to separate fibres from trash particles
by buoyancy differences rather than beating the material against a series of grid bars.
 There are three types of feeding apparatus in the blow-room opening machines

1. Two feed rollers (clamped)

2. Feed roller and a feed table
3. A feed roller and pedals
 Two feed roller arrangements gives the best forwarding motion, but unfortunately results in
greatest clamping distance between the cylinders and the beating element.
 Feed roller and pedal arrangement gives secure clamping throughout the width and a small
clamping distance, which is very critical for an opening machine.
 In a feed roller and table arrangement, the clamping distance can be made very small. This gives
intensive opening, but clamping over the whole width is poor, because the roller presses only on
the highest points
of the web. Thin places in the web can be dragged out of the web as a clump by the beaters.
 Honeydew(sugar) or stickiness in cotton affect the process very badly. Because of that
production and quality is affected. Particles stick to metal surfaces, and it gets aggreavated with
heat and pressure.
These deposits change the surface characteristics which directly affects the quality and running
behavior.
 There are chemicals which can be sprayed to split up the sugar drops to achieve better
distribution. But this system should use water solutions which is not recommended due to various
reasons.
 It is better to control the climate inside the department when sticky cotton is used. Low
temperature (around 22 degree Celsius) and low humidity (45% RH). This requires an expensive
air conditioning set up.
 The easiest way to process sticky cotton is to mix with good cotton and to process through two
blending machines with 6 and 8 doublings and to install machines which will segregate a heavier
particles by buoyancy differences.
 General factors which affect the degree of opening, cleaning and fibre loss are,

1. Thickness of the feed web

2. Density of the feed web
3. Fibre coherence
4. Fibre alignment
5. Size of the flocks in the feed (flock size may be same but density is different)
6. The type of opening device
7. Speed of the opening device
8. Degree of penetration
9. Type of feed (loose or clamped)
10. Distance between feed and opening device
11. Type of opening device
12. Type of clothing
13. Point density of clothing
14. Arrangement of pins, needles, teeth
15. Speeds of the opening devices
16. Throughput speed of material
17. Type of grid bars
18. Area of the grid surface
19. Grid settings
20. Airflow through the grid
21. Condition of pre-opening
22. Quantity of material processed,
23. Position of the machine in the machine sequence
24. Feeding quantity variation to the beater
25. Ambient R.H.%
26. Ambient temperature
 Cotton contains very little dust before ginning. Dust is therefore caused by working of the
material on the machine. New dust is being created through shattering of impurities and
smashing and rubbing of fibres. However removal of dust is not simple. Dust particles are very
light and therefore float with the cotton in the transport stream. Furthermore the particles adhere
quite strongly to the fibres. If they are to be
eliminated, they are to be rubbed off. The main elimination points for adhering dust therefore, are
those points in the process at which high fibre/metal friction or high fibre/fibre friction is produced.
 Removal of finest particles of contaminants and fibre fragments can be accomplished by
releasing the dust into the air, like by turning the material over, and then removing the dust-
contaminated air. Release of dust into the air occurs wherever the raw material is rolled, beaten
or thrown about. Accordingly the air at such positions is sucked away. Perforated drums,
stationary perforated drums, stationary combs etc. are some instruments used to remove dust

PROCESS PARAMETERS IN BLOW ROOM

With all harvesting methods, however, the cotton seed, together with the fibers, always gets into the
ginning plant where it is broken up into trash and seed-coat fragments. This means that ginned cotton is
always contaminated with trash and dust particles and that an intensive cleaning is only possible in the
spinning mill.

Nep content increases drastically with mechanical harvesting, ginning and subsequent cleaning
process. The reduction of the trash content which is necessary for improving cotton grade and
appearance unfortunately results in a higher nep content level.

The basic purpose of  Blow room is to supply :

 Small fibre tufts

 Clean fibre tufts
 Homogeneously blended tufts if more than one variety of fibre is used

to carding machine  without increasing  fibre rupture, fibre neps , broken seed particles and without
removing more  good fibres.

The above is achieved by the following processes in the blow-room :

1. Pre opening
2. Pre cleaning
3. Mixing or blending
4. Fine opening
5. Dedusting

Cleaning Efficiency

Cleaning efficiency of the machine is the ratio of the trash removed  by the machine to that of  total trash
fed to the machine, expressed as percentage

Cleaning = {(Trash in feed % - Trash in del %)} x 100)/(Trash in feed%) efficiency%

Following are the basic parameters to be considered in Blow-room process.

 No of opening machines
 Type of beater
 Type of beating
 Beater speed
 Setting between feed roller and beater
 Production rate of individual machine
 Production rate of the entire line
 Thickness of the feed web
 Density of the feed web
 Fibre micronaire
 Size of the flocks in the feed
 Type of clothing  of the beater
 Point density of clothing
 Type of grid and grid settings
 Air flow through the grid
 Position of the machine in the sequence
 Amount of trash in the material
 Type of trash in the material
 Temp and relative humidity in the blow room department

Preopening

Effective preopening results in smaller tuft sizes, thus creating a large surface area for easy  and
efficient removal of trash particles by the fine openers.

If MBO (Rieter) or  BOW ( Trutzschler) type of machine is used as a first machine

 The tuft size in the mixing should be as small as possible. Normally it should be less than 10
grams
 Since this machine does not take care of long term blending, mixing should be done properly to
maintain the homogenous blending
 The inclined lattice speed and the setting between inclined lattice and clearer roller decides the
production of the machine
 The setting between inclined lattice and clearer roller decides the quality of the tuft.
 If  the setting is too close, the tuft size will be small, but the neps in the cotton will be increased
due to  repeated action of the  inclined lattice pins on cotton.

 The clearance should be decided  first to confirm the quality, then inclined lattice speed can be
decided according to the   production required.
 The setting of inclined lattice depends upon the fibre density, fibre micronaire and the tuft size
fed. If smaller tuft is fed to the feeding conveyor, the fibre tufts will not be recycled many times,
hence the neps will be less.
 If the machine is with beater, it is advisable to use only disc type beater. Saw tooth and Pinned
beaters should not be used in this machine, because the fibre  damage at this stage will be very
high and heavier trash particles will be broken in to small pieces.
 The beater  speed  should be around 500 to 800 rpm depending upon the raw material. Coarser
the fibre,  higher the speed.
 The setting between feed roller to beater should be around 4 to 7 mm.
 This machine is not meant to remove trash ,  hence the fibre loss should also be less.
 Trash removal in this machine will result in breaking the seeds, which is very difficult to remove.
 It is easier to remove the bigger trash than the smaller trash, therefore enough care should be
taken to avoid breaking the trash particles.
 This machine is  just to open the tufts into small sizes so that cleaning becomes easier in the
next machines.
 The fibre tuft size from this  machine should be  preferably around 100 to 200 milligrams.
 If tuft size is  small, removing trash particles becomes easier , because of large surface area.

If Uniflco11(Rieter) or Blendomat BDT 019(Trutzschler) is used as a first machine

 It helps to maintain the homogeneity of the long term blending.

 Cotton is opened gently without recycling as it is done in manual bale openers.
 With the latest automatic bale opening machines,  the tuft size can be as small as 50 to 100
grams without  rupturing the fibres.
 The opening roller speed should be around 1500 to 1800 rpm.
 The depth of penetration of the opening  should be as minimum as possible for better quality.
 It is better to use this machine with one mixing or maximum two mixing at  the same.
 If the production per feeding machine is less than 150 kgs, then four mixings can be
recommended.
 Production rate of this machine depends upon the no of mixings working at the same time.
 Production rate depends  upon opening roller depth, traverse speed and the fibre tuft density.
 In general , the machine parameters should be set in such a way that  maximum number of take-
off points are available  per unit time.
 With the latest machines (Rieter -Unifloc A11), around 60% of take-off points are more compared
to earlier machines.

 Precleaning

Precleaning should be gentle. Since removing finer trash particles is difficult, seeds and bigger trash
particles should not be broken. Finer trash particles require severe treatment in Fine openers. This will
lead to fibre damage and more nep generation. Therefore, precleaning should be as gentle as possible
and no compromise on this. If preopening and precleaning are done  properly,  consistency in trash
removal by fine openers is assured. Dust removal should be started in this machine. Enough care
should be taken remove dust  in this process.

Rieter's Uniclean B11 and Trutzschler's Axiflow or Maxiflow  are the machines which does this work

 The fibre treatment in this machine is very gentle because  the fibres are not gripped by the feed
roller during beating.  Fibre tufts treated by the pin beater when it is carried by air medium.
 All heavy trash particles fall down before it is broken.
 Cleaning efficiency of this machine is very high in the blow room line.
 Mostly all heavy seeds (full seeds) fall in this machine without any problem.
 Around 50 pascal suction pressure should be maintained in the waste chamber for better
cleaning efficiency.
 Beater speed, air velocity through the machine, grid bar setting and gap between grid bars will
affect the cleaning efficiency.
 Higher the cleaning efficiency, higher the good fibre loss, higher the nep generation and higher
the fibre rupture.
 The optimum cleaning means maximum cleaning performance, minimum loss of good fibres, a
high degree of fibre preservation and minimum nep generation.
 Rieter has a unique concept called "VARIOSET". With this machine, selective trash removal is
possible. Waste  amount can be changed in a range of 1:10.

Operating intensity and effectiveness

 Fig. : From Rieter
which shows , degree of cleaning, fibre loss, neps, fibre damage.

 With normal machines like Monocylinder or axiflow, a lot of trials to be conducted to arrive at
optimum beater speed, air velocity(fan speed), grid bar setting and grid bar gap.
 in general the beater speed is around 750 and  minimum 50 pascal suction pressure to be
maintained in the suction chamber.

 Blending

 Barre or streakiness is due to uneven mixing of different cottons. Hence mixing technology is a
decisive factor in spinning mill technology.
 Bigger the differences of cotton parameters like fineness, color and staple length, the greater the
importance of mixing.
 If the cotton has honeydew, the intensive mixing of the raw material is a precondition   for an
acceptable running behavior  of the complete spinning mill .

Following  fig is given by trutzschler for different  mixing requirements:

                        Standard      Standar-plus     High       High-end

 Trutzschler's tandem mixing concept is an  ultimate solution, if the mixing requirement is very
high. This principle guarantees a maximum homogeneous of the mix

 Fig. : Tandem mixing concept from TRUTZSCHLER:

Fine Cleaning

Fine cleaning is done with different types of machines. Some fine cleaners are with single opening
rollers  and some are with multiple opening rollers.
 If single roller cleaning  machines are used, depending upon the  amount and type of trash in the
cotton, the number of fine cleaning points can be either one or two. 
 If the production  rate is lower than 250 kgs and the micronaire is less than 4.0, it is advisable to
use single roller cleaning machines instead of multiple roller cleaning machine.
 Saw tooth beaters can be used, if trash particles are more and the machine is not using suction
and deflector blades. i.e beater and regualar grid bar arrangements
 Normal beater speeds with sawtooth beater depends upon the production rate,  fibre micronaire
and trash content

PROUDCTION
TYPE OF COTTON COTTON MICRONAIRE BEATER SPEED rpm
RATE kgs/hr
200 to 300
More trash 3.5 to 4.0 600 to 750
kgs /hr
200 to 300
Less trash 3.5 to 4.0 600 to 750
kgs/hr
More trash 4.0 to 4.5 200 to 300 kgs 700 to 850
Less trash 4.0 to 4.5 350 to 500 kgs 1000 and above

 The number of wire points depends on the proudction rate and trash.
 Setting between feed roller and beater depends on the production rate and micronaire.   The
setting should be around 2 to 3 mm.  Wider setting always result  in higher rawmaterial faults, if
carding does not take care.
 Closer the setting between beater and moteknives, higher the waste collected. It is advisable to
keep around 3 mm.
 If it is a Trutzschler blowroom line, it is better to use  CVT1 ( single opening roller machine) if 
roller ginned cotton  is used.
 CVT3  or CVT4 machines with 3 or 4 opening rollers can be used for saw ginned cotton.

 The cleaning points in CVT1, CVT3, CVT4 etc consists of opening roller, deflector blades,
moteknives and suction hood. Trash particles released due to centrifugal forces are  separated at
the moteknives and continuously taken away by the  suction. This gives better cleaning.
 Fig. : Trash removal concept in CVT cleaners

 suction plays a major role in these machines. If suction  is not consistent , the performance will
be affected badly.  Very high suction will result in more white fibre loss and less suction will result
in low cleaning efficiency.
 The minimum recommended pressure in the waste chamber (P2) is 700 pascals. It can be upto
1000 pascals.
 Material suction (P1) should be around 500 pascals. 
 Whenever the suction pressure is changed, the deflector blade settings should be  checked
 Deflector blade setting can not be same for all the three rollers or four rollers. The setting for
deflector blades in the panel looks like this 3, 12, 30 for 1st, 2nd and 3rd deflector blades.
 The deflector blade setting should be done in such a way that  the setting should be opened till
the fibres start slipping on the deflector blade.
 Wider the deflector blade setting, higher the waste. If the setting is too wide, white fibre loss will
be very high.
 For saw ginned cottons, the above concepts helps a lot because of constant suction
concentrated directly at the moteknives, ensures much removal of dust from the cotton.

 Dedusting

Apart from opening cleaning of rawmaterial, dedusting is the very important process in blowroom
process.

 normally dedusting  starts with precleaning.

 It is always better to have a separate machine like DUSTEX of TRUTZSCHLER  for effecive
dedusting.
 Dedusting keeps the atmospheric air clean.
 Dedusting in machines like unimix , ERM of Rieter is  good.
 Stationary dedusting condensers can be used for this purpose.
 In exhausts of  unimix , condensers , ERM etc, positive pressure of 100 pascal should be
maintained. Exhaust fan speed and volume should be accordingly selected.
 DUSTEX should be installed before feeding to the cards, because better the fibre  opening better
the dedusting.
 Fine opners like ERM, CVT cleaners also help in dedusting.
 It is always better to feed the material through condenser for a feeding machine of cards. 
Because condenser continuously removes the dust from a small quantity of fibres  and the
material  fed to the feeding machine is opened to some extent.
 Since material is not opened well in Unimix, the dedusting may not be very effective, even
though  dedusting concept in Unimix is very good.
 For rotor spinning dedusting is very important. It is better to use a machine like DUSTEX  after
the fine opener.

Other Important Things in Blow-room

 Setting between feed rollers is different for different types. It should be according to the standard
specified by the manufacturer.  For Unimix it should be around 1 mm.
 It is advisable to run the fans at optimum speeds.  Higher fan speeds will increase the material
velocity and will create  turbulance  in the bends. This will result in curly fibres which will lead to
entanglements.
 If the feeding to cards  is not with CONTI-FEED, the efficiency of the feeding machine should be
minimum 90 % and can not be more than 95%.
 If the cards are fed by CONTI-FEED system,  the feed roller speed variation should not be more
than 10%.  If the variation is more, then the variation in tuft size also will be more. Hence the
quality will not be uniform.
 If two feeding machines feed to 10 cards and the no of cards can be changed according the
requirement, then frequent changes will affect the tuft size which will affect the quality, if the line
is fixed with CONTI-FEED.
 If contifeed system is tuned properly and there are no machine stoppages, continuous material
flow will  result in better opening and even feeding to the cards
 If the production rate per line is high, the reserve chamber  for  the feeding machine should be
big enough to avoid long term feed variations.
 It is advisable to reduce the number of fans  in the line. 
 Fan speeds, layout of machines should be selected in such a way that material choking in the
pipe line, beater jamming etc will not happen.  This will lead to quality problems.
 All blowroom machines should work with maximum efficiency. The feed roller speeds  should be
selected in such a way that  it works atleast 90% of the running time of the next machine.
 Blow room stoppages will always affect the sliver quality both in terms of linear density and   tuft
size. Blow room stoppages  should be nil in a mill.
 Heavy particles like metal particles, stones should be removed using heavy particle removers ,
double magnets etc, before they damage  the opening rollers and other machine parts.
 Number of cleaning  points are decided based on  type of ginning (whether roller ginned or saw
ginned), the amount of trash, and the number of trash particles and the type of trash particles.
 Machinery selection should be based on the type of cotton and production requirement. If the
production requirement of a blowroom line is less than 200 kgs,  CVT-4 cleaner can not be 
recommended, instead CVT-1 can be used.
 Since blow room requires more space and power, it is better to make use of the maximum
production capacity of the machines.
 Material level in the storage chambers  should be full  and it should never be less than 1/4th level.
 Grid bars should be inspected periodically, damaged grid bars  should be replaced.
 Grid bars in  the front rows can be replaced earlier.

 If the cotton is too sticky, the deposits on the machine parts  should be cleaned atleast once in a
week, before it obstruct the movement of the fibre.
 Fibre rupture should be checked for each opening point.  2.5 % span length should not drop by
more than 3% . If the uniformity ratio drops by more than 3%, then  it  is considered that there is
fibre rupture.
 High fan speed, which will result in high velocity of air will increase neps in cotton.
 Nep is increased in the blowroom process.  The increase should not be more than 100%.
 The nep increase in each opening machine should be checked  with different beater speeds and
settings, and the optimum  parameters  should be selected. But please remember that everything
should be based on  yarn quality checking.  e.g. if nep increase in blow room is  more and the
beater speed or feed roller setting is changed, the tuft size will become more. This may result in
bad carding quality.
 Sometimes if the neps are slightly more and the  fibre is well opened, the neps can be removed
by cards and combers and the yarn quality may be better.  Therefore all trials should be done
upto yarn stage.

No of neps and trash particles  after different processes is given below. (an approximate value)

 Blow room machinery lay out should be designed in such a way that there should be minimum
number of bends, and there should not be sharp bends  to avoid fibre entanglements.
  Fibre travelling  surface should be smooth and clean
 Temperature should be around 30 degrees and the humidity is around 55 to 60%.

A best blowroom can be achieved by selecting the following machines:

1. RIETER UNIFLOC- A11 ( pre opening)

2. RIETER UNICLEAN B11 (  pre cleaning)

3. TRUTZSCHLER MPM 6 + MPM6 ( two mixers for blending)

4. TRUTZSCHLER CVT-1 ( for  roller ginned cotton) CVT-3 ( for saw ginned)

5. CONTAMINATION DETECTOR from either BARCO OR JOSSI

6. TRUTZSCHLER  DUSTEX-DX ( for dedusting)

7. TRUTZSCHLER CONTI-FEED and others

But enough care should be taken to synchronise the machines for better performance   , and to run the
line without any electrical system breakdowns.