Scribd
Upload
78 views

Reservoir Simulation Tutorials: Barham Sabir Mahmood

This document provides instructions for building a reservoir simulation model from scratch in Eclipse including defining a grid imported from a FILL file, specifying layer petrophysical properties, PVT properties for oil and water, relative permeability and capillary pressure curves, and defining a single oil producer well with start date and economic limits over a 10 year period. Tips are provided for visualizing output and addressing potential convergence errors.

Uploaded by

arez muhammed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
78 views

Reservoir Simulation Tutorials: Barham Sabir Mahmood

This document provides instructions for building a reservoir simulation model from scratch in Eclipse including defining a grid imported from a FILL file, specifying layer petrophysical properties, PVT properties for oil and water, relative permeability and capillary pressure curves, and defining a single oil producer well with start date and economic limits over a 10 year period. Tips are provided for visualizing output and addressing potential convergence errors.

Uploaded by

arez muhammed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

2018

Reservoir Simulation Tutorials

Barham Sabir Mahmood


Petroleum Engineering Dep.
Exercise 3

In this exercise we will build a complete data file from scratch.


The RUNSPEC section must be defined at last, so that it agrees with what we’ve used
in the other sections.

GRID.

We want a grid that’s a little more interesting than those that are easily constructed
directly in the data file. The grid is normally generated from maps. Since that is not
covered in the course, we will use an alternative route, by the program FILL. You are
not required to learn or understand FILL, but for those who are interested, the input
file to FILL will be our starting point. (FILL can be a good alternative for those of
you who later may want to construct grids which are more complicated than those that
can be constructed inside Eclipse, but don’t need or want to go the full step to RMS or
FloGrid. May be relevant for some Master or PhD studies. If you don’t see this as
interesting or necessary, you can include the attached file EX3GRID.FILLED as a
black box.)

Description of reservoir model (contents of FILLED-file – nothing of this needs to be


defined explicitly in the ECLIPSE DATA file).
The reservoir is enveloped by a rectangular area, 3.3 km wide (E-W direction) and 6,5
km long (N-S direction). The grid comprises 30 x 50 x 6 blocks, with grid block
lengths in x-direction (DX):
5 blocks, each 200m, 5 blocks, each 150m, 10 blocks of 100m, 5 blocks of 70m, and 5
blocks of 40m.

In the y-direction (DY): 10 blocks of 200m, 10 blocks of 100m, 10 blocks of 50m, 10


blocks of 100m, and 10 blocks of 200m.
The layers will have constant thickness, top layer: 10m thick; layer 2: 15m thick;
layers 3 and 4: 5m; layer 5: 10m; layer 6: 20m.

The reservoir slopes downward towards NW, with the four top corners at depths: NW:
2400m SMSL (Sub Mean Sea Level), NE: 2020 m SMSL, SE: 1880 m SMSL, SW:
2200m SMSL.
In addition, two points along the center north-south line are given: North center at
2120m SMSL, and South center at 1950m SMSL.

The grid doesn’t cover the entire envelope rectangle, in NW, a triangle 1,75km (EW)
x 2,5km (NS) is missing, in NE a triangle 200m (EW) x 2km (NS) is missing, and in
SE a triangle 2km (NS) with width the whole grid is missing.

In addition, the top of the grid is eroded, such that all blocks with I = 24-30 are
missing in the top layer, and all blocks with I=28-30 in layer 2.

Petrophysics:

Layer Porosity x-permeability net to gross


1 0.31 5000 1.0
2 0.28 2800 0.9
3 0.24(downdip) – 0.28 (updip) 200 (dd) – 2000 (ud) 0.5 (dd) – 0.9 (ud)
4 as layer 3 as layer 3 as layer 3
5 0.21 50 0.4
6 0.25 50 0.4

y-permeability is equal to x-permeability, while z-permeability is 10% of this.

All of the above is defined in the file EX3GRID.FILL. If you want to generate a grid
from this input you will need to install and run the program FILL on your PC.
Processing EX3GRID.FILL with FILL generates a file EX3GRID.FILLED (which is
also included in the files attached to this exercise).

The GRID section of your DATA file will consist of a single statement,
INCLUDE’ing this file.

Take a quick look at the file EX3GRID.FILLED, and confirm that it contains the grid
defined by keywords COORD and ZCORN as we should expect. Also look at
ACTNUM and some petrophysics.

Additional data:

The simulation shall be organized such that the oil is above the bubble point, 227 bars,
at all times, i.e. we consider dead oil. No free gas, i.e. Rs will be constant.
The oil-water contact is at 2250m SMSL.
Use a reference pressure of 320 bars at datum depth 1900m SMSL. Saturation
equilibration initialization shall be with cell center saturations.

Relative permeability:

Sw Krw Kro Pc
0.2 0 0.85 0
0.25 0.006 0.727 0
0.3 0.013 0.613 0
0.35 0.022 0.509 0
0.4 0.032 0.414 0
0.45 0.043 0.330 0
0.5 0.057 0.255 0
0.55 0.071 0.189 0
0.6 0.087 0.133 0
0.65 0.105 0.087 0
0.7 0.124 0.51 0
0.75 0.144 0.024 0
0.8 0.167 0.007 0
0.85 0.190 0 0
0.9 0.215 0 0
1 1 0 0

PVT-data:
Water has a volume factor of 1.024 at a pressure of 308.2 bars. At this pressure, water
compressibility is 4.64E-5 bars-1, and viscosity is 0.42 cP.

For dead oil, we have been given the following table:

Pressure (bars) Volume factor (Sm3/m3) Viscosity (cP)


227.0 1.2600 1.042
253.4 1.2555 1.072
281.6 1.2507 1.096
311.1 1.2463 1.118
343.8 1.24173 1.151
373.5 1.2377 1.174
395.5 1.2356 1.200

The (constant) Rs is 100 Sm3/Sm3, taken at 227 bars (Pbp).

Densities (kg / Sm3):


Oil: 883 Water: 1038 Gas: 0.66
Rock compressibility is assumed linear, with a compressibility coefficient of
0.000056 bars-1 at a pressure of 1 bar.

In Eclipse Office, the input data can be visualized graphically, e.g. relperm-curves.

Wells:
Define a single oil producer in grid block column 23, 38, completed in layers 1 – 5.
Use a well diameter of 0.31 m.
The initial oil rate will amount to approx. 2% of total STOIIP (Stock tank (i.e.
standard conditions) Oil Initially In Place) pr year. Remember to define bubble point
pressure as minimum allowed pressure. Set economic limits of min. oil rate 200
Sm3/day, max water cut 0.9. End run if these are violated.
Start date: 1.1.2018, define DATES or TSTEP each half year after that, for 10 years.

To get output that can be viewed in FloViz, you will need to use the RPTRST
keyword at the start of the SCHEDULE section (hasn’t been lectured yet.) Just copy it
from the Ex2.DATA file.
(RPTRST BASIC=5, FREQ=6 / )

The NOSIM keyword allows for data checking and reporting without running the
simulation.

You will probably not get any convergence error reports. But in case you do; are there
any easy fixes for that? (TUNING)

You might also like