TRUE VALUE CALIBRATION SERVICES PRIVATE

LIMITED
has been assessed and accredited in accordance with the standard

ISO/IEC 17025:2017
''General Requirements for the Competence of Testing &
Calibration Laboratories''
for its facilities at
NO. 92 S R B NAGAR MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU, INDIA

in the field of

CALIBRATION
Certificate Number: CC-2144
Issue Date: 10/05/2019 Valid Until: 09/05/2021

This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continued
satisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)

Signed for and on behalf of NABL

N. Venkateswaran
Chief Executive Officer (I/c)
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 1 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
Permanent Facility

1 MECHANICAL- SPEED ( Non Contact 10 RPM to 90000 RPM 7% to 0.01% Using Digital
ACCELERATION AND type)Tachometer, Tachometer and
SPEED Stroboscope, RPM / procedure based on
Speed (Indicator / Sanas TR 45-02.
Meter / Source)

2 MECHANICAL- SPEED (Contact 10 RPM to 8000 RPM 6.2% to 0.04% Using Digital
ACCELERATION AND type)Tachometer Tachometer and
SPEED procedure based on
Sanas TR 45-2.

3 MECHANICAL- DENSITYDensity 0.6 g/ml to 2.0 g/ml 0.0006g/ml By Electronic Weighing

DENSITY AND Hydrometer / Brix Balance of readability
VISCOSITY Hydrometer / Baume 0.01/0.1 mg and known
Hydrometer / Twaddle liquid density as Per
Hydrometer/ Specific NIST SP 250-78 by
Gravity Hydrometer / Hydrostatic Weighing
Lactometer / Method
Alcoholmeter

4 MECHANICAL- Calibration of Push Pull 0 N to 2000 N 0.14% Using different

MOBILE FORCE Gauge/ Force Gauge Denomination of
MEASURING SYSTEM Newton Weights and
different loading frames
as per VDI/VDE 2624

5 MECHANICAL- PRESSURE 0 bar to 700 bar 0.09% Rdg. Pressure Calibrator

PRESSURE HYDRAULICPressure with a uncertainty of
INDICATING DEVICES Gauge, Pressure 0.091 bar. Procedure
Indicator, Pressure based as per DKD R 6-
controller, Pressure 1
Transmitter, Pressure
Recorder

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 2 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
6 MECHANICAL- PRESSURE 0 mmWC to 200 0.29% Rdg. Using Low Pressure
PRESSURE PNEUMATIC (Pressure mmWC (0 to 0.20 Bar) Calibrator with a
INDICATING DEVICES Gauge, Pressure uncertainty of 0.062
Indicator, Pressure mmWC. Procedure
controller, Pressure based as per DKD R 6-
Transmitter, Maghnelic 1
Gauge, Manometers,
Pressure Recorder,
Pressure Switch.

7 MECHANICAL- PRESSURE 0 bar to 40 bar 0.15% Rdg. Using Pressure

PRESSURE PNEUMATICPressure Calibrator with a
INDICATING DEVICES Gauge, Pressure uncertainty of 0.0044
Indicator, Pressure bar. Procedure based
controller, Pressure as per DKD R 6-1
Transmitter, Maghnelic
Gauge, Manometers,
Pressure Recorder,
Pressure Switch.

8 MECHANICAL- VACUUM -200 mmWC to 0 0.29% Rdg. Using Low Pressure

PRESSURE PNEUMATIC(Vacuum mmWC (-0.20 to 0 Bar) Calibrator with a
INDICATING DEVICES Gauge, Vacuum uncertainty of 0.062
Indicator, Vacuum mmWC. Procedure
Transmitter, Vacuum based as per DKD R 6-
Transducer, Vacuum 1
Recorder, Maghnelic
Gauge, Low Pressure
calibrators/Gauges)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 3 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
9 MECHANICAL- VACUUMVacuum (-) 0.85 bar to 0 bar 5.9% Rdg. Using Pressure
PRESSURE Gauge, Vacuum Calibrator with a
INDICATING DEVICES Indicator, Vacuum uncertainty of 0.0006
Transmitter, Vacuum bar. Procedure based
Transducer, Vacuum as per ISO 3567 & ISO
Recorder, Maghnelic 27893.
Gauge, Low Pressure
calibrators/Gauges)

10 MECHANICAL- UTM, Verification of Upto 12.7 mm 3.45% Using Digital

TENSION CREEP Extensometer used in Comparator as per the
AND TORSION Material Testing IS12872:2010, ISO
TESTING MACHINE Machine - Gauge 9513:2012 & ASTM
length Upto 200mm E83:2016

11 MECHANICAL- UTM, Verification of Universal 50 N to 500 kN 0.36% Using Load Cell with
TENSION CREEP Testing Machine Indicator as per the IS
AND TORSION Tension Mode 1828:2015 Part 1 /
TESTING MACHINE ISO7500 Part 1

12 MECHANICAL- VOLUME Piston 10 µl to 100 µl 0.26µl Using Precision

VOLUME Operated Volumeteric Balance by Gravimetric
Apparatus Method Procedure
(Micropipette) based on ISO 8655-6

13 MECHANICAL- VOLUME 10 ml to 20 ml 5.9µl Using Precision

VOLUME Pipette/Burette/ Balance by Gravimetric
Measuring Method Procedure
Cylinder/Beakers/ based on ISO 4787
Volumetric Flask

14 MECHANICAL- VOLUME Piston 1 ml to 10 ml 0.36µl Using Precision

VOLUME Operated Volumeteric Balance by Gravimetric
Apparatus Method Procedure
(Micropipette) based on ISO 8655-6

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 4 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
15 MECHANICAL- VOLUMEMeasuring 1 L to 5 L 0.2ml Using Precision
VOLUME Cylinder/Beakers/ Balance ( readability
Volumetric 0.1 mg) by Gravimetric
Flask/Conical Flask Method Procedure
based on ISO 4787

16 MECHANICAL- VOLUMEMeasuring 500 ml to 1 L 0.1ml Using Precision

VOLUME Cylinder/Beakers/ Balance by Gravimetric
Volumetric Method Procedure
Flask/Conical Flask based on ISO 4787

17 MECHANICAL- VOLUMEPipette/Burett 1 ml to 10 ml 5.9µl Using Precision

VOLUME e/ Measuring Balance ( readability
Cylinder/Beakers/ 0.01 mg) by
Volumetric Flask Gravimetric Method.
Procedure based on
ISO 4787

18 MECHANICAL- VOLUMEPipette/Burett 100 ml to 500 ml 7.6µl Using Precision

VOLUME e/ Measuring Balance by Gravimetric
Cylinder/Beakers/ Method Procedure
Volumetric Flask based on ISO 4787

19 MECHANICAL- VOLUMEPipette/Burett 20 ml to 50 ml 7.6µl Using Precision

VOLUME e/ Measuring Balance by Gravimetric
Cylinder/Beakers/ Method Procedure
Volumetric Flask based on ISO 4787

20 MECHANICAL- VOLUMEPipette/Burett 50 ml to 100 ml 7.6µl Using Precision

VOLUME e/ Measuring Balance by Gravimetric
Cylinder/Beakers/ Method Procedure
Volumetric Flask based on ISO 4787

21 MECHANICAL- VOLUMEPiston 1 µl to 10 µl 0.094µl Using Precision

VOLUME Operated Volumeteric Balance ( readability
Apparatus 0.001 mg) by
(Micropipette) Gravimetric Method.
µmProcedure based on
ISO 8655-6

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 5 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
22 MECHANICAL- VOLUMEPiston 100 µl to 1000 µl 0.36µl Using Precision
VOLUME Operated Volumeteric Balance by Gravimetric
Apparatus Method Procedure
(Micropipette) based on ISO 8655-6

23 MECHANICAL- Calibration of weights 1g 0.003mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles by Substitution
method.

24 MECHANICAL- Calibration of weights 1 kg 0.16mg Using E1 Class

WEIGHTS Weights and Mass
Comparator (L.C. 0.1
mg ) as per OIML R-
111 : 2004 through
ABBA Cycles by
Substitution Method

25 MECHANICAL- Calibration of weights 10 g 0.006mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles.

26 MECHANICAL- Calibration of weights 10 kg 48mg Using E2 Class

WEIGHTS Weights and Electronic
Balance as per OIML
R-111 : 2004 through
ABBA Cycles by
Substitution Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 6 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
27 MECHANICAL- Calibration of weights 100 g 0.0156mg Using E1 Class
WEIGHTS Weights and Semi -
Micro Balance (L.C.
0.01 mg ) as per OIML
R-111 : 2004 through
ABBA Cycles by
Substitution Method

28 MECHANICAL- Calibration of weights 2g 0.0032mg Using E1 Class

WEIGHTS Weights and Micro
Balance (Readability
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles.

29 MECHANICAL- Calibration of weights 2 kg 0.28mg Using E1 Class

WEIGHTS Weights and Mass
Comparator (L.C. 0.1
mg ) as per OIML R-
111 : 2004 through
ABBA Cycles by
Substitution Method

30 MECHANICAL- Calibration of weights 20 g 0.008mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles.

31 MECHANICAL- Calibration of weights 20 kg 66mg Using E2 Class

WEIGHTS Weights and Electronic
Balance as per OIML
R-111 : 2004 through
ABBA Cycles by
Substitution Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 7 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
32 MECHANICAL- Calibration of weights 200 g 0.026mg Using E1 Class
WEIGHTS Weights and Semi -
Micro Balance (L.C.
0.01 mg ) as per OIML
R-111 : 2004 through
ABBA Cycles.

33 MECHANICAL- Calibration of weights 5g 0.005mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles.

34 MECHANICAL- Calibration of weights 5 kg 0.51mg Using E1 Class

WEIGHTS Weights and Mass
Comparator (L.C. 0.1
mg ) as per OIML R-
111 : 2004 through
ABBA Cycles by
Substitution Method

35 MECHANICAL- Calibration of weights 50 g 0.01mg Using E1 Class

WEIGHTS Weights and Semi -
Micro Balance (L.C.
0.01 mg ) as per OIML
R-111 : 2004 through
ABBA Cycles.

36 MECHANICAL- Calibration of weights 50 kg 80mg Using E2 Class

WEIGHTS Weights and Electronic
Balance as per OIML
R-111 : 2004 through
ABBA Cycles by
Substitution Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 8 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
37 MECHANICAL- Calibration of weights 50 mg 0.001mg Using E1 Class
WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles by Subdivision
method

38 MECHANICAL- Calibration of weights 500 g 0.083mg Using E1 Class

WEIGHTS Weights and Mass
Comparator (L.C. 0.1
mg ) as per OIML R-
111 : 2004 through
ABBA Cycles by
Substitution Method

39 MECHANICAL- Mass - weights 1 mg 0.001mg Using E1 Class

WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision method

40 MECHANICAL- MASS - weights 10 mg 0.001mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles by Subdivision
method.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 9 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
41 MECHANICAL- MASS - weights 100 mg 0.0012mg Using E1 Class
WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision Method

42 MECHANICAL- MASS - weights 2 mg 0.001mg Using E1 Class

WEIGHTS Weights and Micro
Balance (L.C. 0.001 mg
) as per OIML R-111 :
2004 through ABBA
Cycles by Subdivision
method.

43 MECHANICAL- MASS - weights 20 mg 0.001mg Using E1 Class

WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision method

44 MECHANICAL- MASS - weights 200 mg 0.0012mg Using E1 Class

WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 10 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
45 MECHANICAL- MASS - weights 5 mg 0.001mg Using E1 Class
WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision method.

46 MECHANICAL- MASS - weights 500 mg 0.0018mg Using E1 Class

WEIGHTS Weights and Micro
Balance (readability:
0.001 mg ) as per
OIML R-111 : 2004
through ABBA Cycles
by Subdivision Method

47 THERMAL- SPECIFIC Calibration of Humidity 5 °C to 50 °C 0.7°C Using Temperature and

HEAT & HUMIDITY Indicator, Humidity Humidity Generator
Transmitter, Thermo with Temperature and
Hygrometer, Humidity Humidity Indicator with
Sensor/ Probe - @50% Sensor by Comparison
RH Method

48 THERMAL- SPECIFIC Calibration of Humidity 20 % to 95 % 1.71% Using Temperature and

HEAT & HUMIDITY Indicator, Humidity Humidity Generator
Transmitter, Thermo with Temperature and
Hygrometer, Humidity Humidity Indicator with
Sensor/ Probe - 20°C Sensor by Comparison
to 50°C Method

49 THERMAL- Calibration of 400 °C to 650 °C 2°C Using Multifunction

TEMPERATURE TemperatureThermom calibrator with N Type
eter, RTD Sensor, TC with Dry Block
Thermocouple, calibrator by
Temperature Indicator/ comparison Method
Controller/ Transmitter/
Recorder with Sensor

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 11 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
50 THERMAL- Calibration of 50 °C to 400 °C 1.25°C Using Multifunction
TEMPERATURE TemperatureThermom calibrator with RTD
eter, RTD Sensor, sensor with Dry Block
Thermocouple, calibrator by
Temperature Indicator/ comparison Method
Controller/ Transmitter/
Recorder with Sensor

51 THERMAL- Indicator Calibration of 400 °C to 1200 °C 3.45°C Using Multifunction

TEMPERATURE TemperatureTemperat calibrator with N Type
ure Bath, Liquid Bath, & S Type TC by
Dry Block Calibrator, comparison Method
Temperature
Indicator/Recorder/Con
troller with sensor of
Deep Freezer, Freezer,
Incubator, Autoclave,
Chamber for industrial
applications

52 THERMAL- Indicator Calibration of -80 °C to 400 °C 1.25°C Using Multifunction

TEMPERATURE TemperatureTemperat calibrator with RTD
ure Bath, Liquid Bath, sensor by comparison
Dry Block Calibrator, Method
Temperature
Indicator/Recorder/Con
troller with sensor of
Deep Freezer, Freezer,
Incubator, Autoclave,
Chamber for industrial
applications

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 12 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
Site Facility

1 MECHANICAL- SPEED (Non 10 RPM to 10000 RPM 0.72RPM to 4.0RPM Using Digital
ACCELERATION AND contact)Centrifuge, Tachometer and
SPEED RPM meters and procedure based as
indicators. per SANAS TR 45-02.

2 MECHANICAL- Verification of Brinell HBW 10/3000 1.0% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1500(Part II) /
ISO 6506-2 By Indirect
Method

3 MECHANICAL- Verification of Brinell HBW 5/750 1.4% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1500(Part II) /
ISO 6506-2 By Indirect
Method

4 MECHANICAL- Verification of Brinell HBW 2.5/187.5 1.6% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1500(Part II) /
ISO 6506-2 By Indirect
Method

5 MECHANICAL- Verification of Rockwell HRA 0.87HRA Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1586(Part II) /
ISO 6508-2 By Indirect
Method

6 MECHANICAL- Verification of Rockwell HRBW 0.90HRBW Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1586(Part II) /
ISO 6508-2 By Indirect
Method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 13 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
7 MECHANICAL- Verification of Rockwell HRC 0.87HRC Using Standard
HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1586(Part II) /
ISO 6508-2 By Indirect
Method

8 MECHANICAL- Verification of Vickers HV 10 1.6% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1501(Part II) /
ISO 6507-2 By Indirect
Method

9 MECHANICAL- Verification of Vickers HV 30 1.3% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1501(Part II) /
ISO 6507-2 By Indirect
Method

10 MECHANICAL- Verification of Vickers HV 5 1.8% Using Standard

HARDNESS TESTING Hardness Testing Hardness Blocks as
MACHINES Machine per IS 1501(Part II) /
ISO 6507-2 By Indirect
Method

11 MECHANICAL- Verification of Impact 0 J to 450 J 0.54% Using traceable

IMPACT TESTING Testing Standard Gauges,
MACHINE MachineCharpy/Izod Clinometer, Load cell,
Steel Tape and other
equipment’s As per
ISO 148-2 / ASTM
E23-16 / IS 3766 /BS
131 (Part 4)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 14 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
12 MECHANICAL- PRESSURE 0 bar to 700 bar 0.09% Rdg. Pressure Calibrator
PRESSURE HYDRAULICPressure with a uncertainty of
INDICATING DEVICES Gauge, Pressure 0.091 bar. Procedure
Indicator, Pressure based as per DKD R 6-
controller, Pressure 1
Transmitter, Pressure
Recorder

13 MECHANICAL- PRESSURE 0 mmWC to 200 0.29% Rdg. Using Low Pressure

PRESSURE PNEUMATIC (Pressure mmWC (0 to 0.20 Bar) Calibrator with a
INDICATING DEVICES Gauge, Pressure uncertainty of 0.062
Indicator, Pressure mmWC. Procedure
controller, Pressure based as per DKD R 6-
Transmitter, Maghnelic 1
Gauge, Manometers,
Pressure Recorder,
Pressure Switch.

14 MECHANICAL- PRESSURE 0 bar to 40 bar 0.15% Rdg. Using Pressure

PRESSURE PNEUMATICPressure Calibrator with a
INDICATING DEVICES Gauge, Pressure uncertainty of 0.0044
Indicator, Pressure bar. Procedure based
controller, Pressure as per DKD R 6-1
Transmitter, Maghnelic
Gauge, Manometers,
Pressure Recorder,
Pressure Switch.

15 MECHANICAL- VACUUM -200 mmWC to 0 0.29% Rdg. Using Low Pressure

PRESSURE PNEUMATIC(Vacuum mmWC (-0.20 to 0 Bar) Calibrator with a
INDICATING DEVICES Gauge, Vacuum uncertainty of 0.062
Indicator, Vacuum mmWC. Procedure
Transmitter, Vacuum based as per DKD R 6-
Transducer, Vacuum 1
Recorder, Maghnelic
Gauge, Low Pressure
calibrators/Gauges)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 15 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
16 MECHANICAL- VACUUMVacuum (-) 0.85 bar to 0 bar 5.9% Rdg. Using Pressure
PRESSURE Gauge, Vacuum Calibrator with a
INDICATING DEVICES Indicator, Vacuum uncertainty of 0.0006
Transmitter, Vacuum bar. Procedure based
Transducer, Vacuum as per ISO 3567 & ISO
Recorder, Maghnelic 27893.
Gauge, Low Pressure
calibrators/Gauges)

17 MECHANICAL- UTM, Verification of 0 mm to 600 mm 0.5mm Using Height gauge As

TENSION CREEP Displacement per ASTM E 2309 by
AND TORSION Measuring System and Comparison Method
TESTING MACHINE Devices used in
Material Testing
Machine

18 MECHANICAL- UTM, Verification of Upto 12.7 mm 3.45% Using Digital

TENSION CREEP Extensometer used in Comparator as per the
AND TORSION Material Testing IS12872:2010, ISO
TESTING MACHINE Machine - Gauge 9513:2012 & ASTM
length Upto 200mm E83:2016

19 MECHANICAL- UTM, Verification of Speed Upto 500 mm/min 0.22mm/min As per ASTM E 2658
TENSION CREEP for Material Testing by Comparison Method
AND TORSION Machine
TESTING MACHINE

20 MECHANICAL- UTM, Verification of Universal 50 N to 500 kN 0.36% Using Load Cell with
TENSION CREEP Testing Machine Indicator as per the IS
AND TORSION Tension Mode 1828:2015 Part 1 /
TESTING MACHINE ISO7500 Part 1

21 MECHANICAL- UTM, Verification of Universal 50 N to 1000 kN 0.32% Using Load Cell with
TENSION CREEP Testing Indicator as per the IS
AND TORSION MachineCompression 1828:2015 Part 1 /
TESTING MACHINE Mode ISO7500 Part 1

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 16 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
22 MECHANICAL- MASSClass I 5.1 kg to 64 kg 0.07g Using E2 Class
WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances & Mass Weights and procedure
Comparators (L.C = 0.1 based as per OIML R-
g) 76

23 MECHANICAL- MASSClass I 220 g to 5.1 kg 0.6mg Using E1 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances & Mass Weights as per OIML
Comparators (L.C = R- 76
0.1mg)

24 MECHANICAL- MASSClass I upto 21 g 0.003mg Using E1 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances & Mass Weights and procedure
Comparators based as per OIML R-
(readability: 0.001mg) 76

25 MECHANICAL- MASSClass I 21 g to 220 g 0.028mg Using E1 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances & Mass Weights and procedure
Comparators (L.C = based as per OIML R-
0.01mg) 76

26 MECHANICAL- MASSClass III 64 kg to 100 kg 20g Using F2 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances (readability: Weights and procedure
10 g) based as per OIML R-
76

27 MECHANICAL- MASSClass III 100 kg to 500 kg 350g Using F2 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances (readability: Weights and procedure
100 g) based as per OIML R-
76

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 17 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
28 MECHANICAL- MASSClass III 500 kg to 1000 kg 498g Using F2 Class
WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances (readability: Weights as per OIML
200 g) R- 76

29 MECHANICAL- MASSClass III 1000 kg to 3000 kg 818g Using F2 & M1 Class

WEIGHING SCALE Electronic Weighing Reference Standard
AND BALANCE Balances (readability: Weights and procedure
500 g) based as per OIML R-
76

30 THERMAL- SPECIFIC Calibration of Humidity 20 % to 95 % 3.95% Using Humidity and

HEAT & HUMIDITY Chamber, Climatic Temperature Data
Chamber, Environment Logger by Comparison
Chamber(Multi- Method
Position)

31 THERMAL- Calibration of -40 °C to 400 °C 2.33°C Using Data Logger,

TEMPERATURE TemperatureDeep RTD Sensor, N Type
Freezer, Freezer, TC by Comparison
Incubator, Hot Air Method
Oven, Water Bath,
Furnace (Multi-
Position) for industrial
applications

32 THERMAL- Calibration of 400 °C to 1000 °C 6.84°C Using Data Logger, N

TEMPERATURE TemperatureDeep Type TC by
Freezer, Freezer, Comparison Method
Incubator, Hot Air
Oven, Water Bath,
Furnace (Multi-
Position) for industrial
applications

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name TRUE VALUE CALIBRATION SERVICES PRIVATE LIMITED, NO. 92 S R B NAGAR
MAIN ROAD, KOLATHUR, CHENNAI, TAMIL NADU , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2144 Page No. : 18 / 18

Validity 10/05/2019 to 09/05/2021 Last Amended on -

S.No Discipline / Group Quantity Measured/ Range / Frequency * Calibration Remarks

Instrument Measurement
Capability(±)
33 THERMAL- Indicator Calibration of 400 °C to 1200 °C 3.45°C Using Multifunction
TEMPERATURE TemperatureTemperat calibrator with N Type
ure Bath, Liquid Bath, & S Type TC by
Dry Block Calibrator, comparison Method
Temperature
Indicator/Recorder/Con
troller with sensor of
Deep Freezer, Freezer,
Incubator, Autoclave,
Chamber for industrial
applications

34 THERMAL- Indicator Calibration of -80 °C to 400 °C 1.25°C Using Multifunction

TEMPERATURE TemperatureTemperat calibrator with RTD
ure Bath, Liquid Bath, sensor by comparison
Dry Block Calibrator, Method
Temperature
Indicator/Recorder/Con
troller with sensor of
Deep Freezer, Freezer,
Incubator, Autoclave,
Chamber for industrial
applications

This is annexure to 'Certificate of Accreditation' and does not require any signature.