Scribd
Upload
60 views

Mandrel Staad Pro EuroCode 700x19t

This document contains a structural analysis of a steel beam (PIP711.2X19) under various load cases. It reports the section properties, load combinations, utilization ratios, and maximum stresses in the beam. The beam is analyzed for 10 sections under 3 load combinations, with the highest stresses of 218.26 N/mm2 found at mid-span under the third load combination. No members were found to fail the design criteria.

Uploaded by

Yap HS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
60 views

Mandrel Staad Pro EuroCode 700x19t

This document contains a structural analysis of a steel beam (PIP711.2X19) under various load cases. It reports the section properties, load combinations, utilization ratios, and maximum stresses in the beam. The beam is analyzed for 10 sections under 3 load combinations, with the highest stresses of 218.26 N/mm2 found at mid-span under the third load combination. No members were found to fail the design criteria.

Uploaded by

Yap HS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Job No Sheet No Rev

1
Part
Software licensed to Hewlett-Packard Company
Job Title Ref

By Date01-May-21 Chd

Client File Shaft.std Date/Time 02-May-2021 02:16

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 PIP711.2X19.0 413.200 248E+3 248E+3 495E+3 STEEL

Combination Load Cases


Comb. Combination L/C Name Primary Primary L/C Name Factor

3 Generated British BS 5950 1 1 LOAD CASE 1 1.40


2 LOAD CASE 2 1.40

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 PIP711.2X19 PIP711.2X19 0.217 1.000 0.217 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
2 PIP711.2X19 PIP711.2X19 0.388 1.000 0.388 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
3 PIP711.2X19 PIP711.2X19 0.510 1.000 0.510 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
4 PIP711.2X19 PIP711.2X19 0.584 1.000 0.584 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
5 PIP711.2X19 PIP711.2X19 0.608 1.000 0.608 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
6 PIP711.2X19 PIP711.2X19 0.608 1.000 0.608 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
7 PIP711.2X19 PIP711.2X19 0.584 1.000 0.584 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
8 PIP711.2X19 PIP711.2X19 0.510 1.000 0.510 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
9 PIP711.2X19 PIP711.2X19 0.388 1.000 0.388 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3
10 PIP711.2X19 PIP711.2X19 0.217 1.000 0.217 EC-6.2.5 3 413.200 248E+3 248E+3 496E+3

Failed Members
There is no data of this type.

Beam Combined Axial and Bending Stresses Summary


Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(mm) (N/mm2) (mm) (N/mm2) (mm)
1 1:LOAD CASE 2E+3 6.827 2E+3 -6.827 2E+3
2:LOAD CASE 2E+3 48.810 2E+3 -48.810 2E+3
3:Generated Br 2E+3 77.892 2E+3 -77.892 2E+3
2 1:LOAD CASE 1.63E+3 11.034 1.63E+3 -11.034 1.63E+3
2:LOAD CASE 1.63E+3 88.469 1.63E+3 -88.469 1.63E+3
3:Generated Br 1.63E+3 139.303 1.63E+3 -139.303 1.63E+3
3 1:LOAD CASE 1.63E+3 14.038 1.63E+3 -14.038 1.63E+3
2:LOAD CASE 1.63E+3 116.796 1.63E+3 -116.796 1.63E+3
3:Generated Br 1.63E+3 183.168 1.63E+3 -183.168 1.63E+3
4 1:LOAD CASE 1.63E+3 15.841 1.63E+3 -15.841 1.63E+3
2:LOAD CASE 1.63E+3 133.793 1.63E+3 -133.793 1.63E+3
3:Generated Br 1.63E+3 209.487 1.63E+3 -209.487 1.63E+3
5 1:LOAD CASE 1.63E+3 16.442 1.63E+3 -16.442 1.63E+3
2:LOAD CASE 1.63E+3 139.458 1.63E+3 -139.458 1.63E+3
3:Generated Br 1.63E+3 218.260 1.63E+3 -218.260 1.63E+3

Print Time/Date: 02/05/2021 02:17 STAAD.Pro V8i (SELECTseries 5) 20.07.10.64 Print Run 1 of 3
Job No Sheet No Rev
2
Part
Software licensed to Hewlett-Packard Company
Job Title Ref

By Date01-May-21 Chd

Client File Shaft.std Date/Time 02-May-2021 02:16

Beam Combined Axial and Bending Stresses Summary Cont...


Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(mm) (N/mm2) (mm) (N/mm2) (mm)
6 1:LOAD CASE 1.63E+3 16.442 0.000 -16.442 0.000
2:LOAD CASE 1.63E+3 139.458 0.000 -139.458 0.000
3:Generated Br 1.63E+3 218.260 0.000 -218.260 0.000
7 1:LOAD CASE 1.63E+3 15.841 0.000 -15.841 0.000
2:LOAD CASE 1.63E+3 133.793 0.000 -133.793 0.000
3:Generated Br 1.63E+3 209.487 0.000 -209.487 0.000
8 1:LOAD CASE 1.63E+3 14.038 0.000 -14.038 0.000
2:LOAD CASE 1.63E+3 116.796 0.000 -116.796 0.000
3:Generated Br 1.63E+3 183.168 0.000 -183.168 0.000
9 1:LOAD CASE 1.63E+3 11.034 0.000 -11.034 0.000
2:LOAD CASE 1.63E+3 88.469 0.000 -88.469 0.000
3:Generated Br 1.63E+3 139.303 0.000 -139.303 0.000
10 1:LOAD CASE 2E+3 6.827 0.000 -6.827 0.000
2:LOAD CASE 2E+3 48.810 0.000 -48.810 0.000
3:Generated Br 2E+3 77.892 0.000 -77.892 0.000

Beam Displacement Detail Summary


Displacements shown in italic indicate the presence of an offset
Beam L/C d X Y Z Resultant
(mm) (mm) (mm) (mm) (mm)
Max X 9 1:LOAD CASE 812.500 0.001 -3.452 0.000 3.452
Min X 9 1:LOAD CASE 650.000 -0.001 -3.629 0.000 3.629
Max Y 1 1:LOAD CASE 0.000 0.000 0.000 0.000 0.000
Min Y 5 3:Generated Br 1.63E+3 0.000 -88.774 0.000 88.774
Max Z 1 1:LOAD CASE 0.000 0.000 0.000 0.000 0.000
Min Z 1 1:LOAD CASE 0.000 0.000 0.000 0.000 0.000
Max Rst 5 3:Generated Br 1.63E+3 0.000 -88.774 0.000 88.774

Beam End Displacements


Displacements shown in italic indicate the presence of an offset
Beam Node L/C X Y Z Resultant
(mm) (mm) (mm) (mm)
1 1 1:LOAD CASE 0.000 0.000 0.000 0.000
2:LOAD CASE 0.000 0.000 0.000 0.000
3:Generated Br 0.000 0.000 0.000 0.000
2 1:LOAD CASE 0.000 -2.518 0.000 2.518
2:LOAD CASE 0.000 -20.410 0.000 20.410
3:Generated Br 0.000 -32.099 0.000 32.099
2 2 1:LOAD CASE 0.000 -2.518 0.000 2.518
2:LOAD CASE 0.000 -20.410 0.000 20.410
3:Generated Br 0.000 -32.099 0.000 32.099
3 1:LOAD CASE 0.000 -4.303 0.000 4.303
2:LOAD CASE 0.000 -35.144 0.000 35.144
3:Generated Br 0.000 -55.226 0.000 55.226
3 3 1:LOAD CASE 0.000 -4.303 0.000 4.303

Print Time/Date: 02/05/2021 02:17 STAAD.Pro V8i (SELECTseries 5) 20.07.10.64 Print Run 2 of 3
Job No Sheet No Rev
3
Part
Software licensed to Hewlett-Packard Company
Job Title Ref

By Date01-May-21 Chd

Client File Shaft.std Date/Time 02-May-2021 02:16

Beam End Displacements Cont...


Beam Node L/C X Y Z Resultant
(mm) (mm) (mm) (mm)
2:LOAD CASE 0.000 -35.144 0.000 35.144
3:Generated Br 0.000 -55.226 0.000 55.226
4 1:LOAD CASE 0.000 -5.686 0.000 5.686
2:LOAD CASE 0.000 -46.695 0.000 46.695
3:Generated Br 0.000 -73.334 0.000 73.334
4 4 1:LOAD CASE 0.000 -5.686 0.000 5.686
2:LOAD CASE 0.000 -46.695 0.000 46.695
3:Generated Br 0.000 -73.334 0.000 73.334
5 1:LOAD CASE 0.000 -6.560 0.000 6.560
2:LOAD CASE 0.000 -54.036 0.000 54.036
3:Generated Br 0.000 -84.834 0.000 84.834
5 5 1:LOAD CASE 0.000 -6.560 0.000 6.560
2:LOAD CASE 0.000 -54.036 0.000 54.036
3:Generated Br 0.000 -84.834 0.000 84.834
6 1:LOAD CASE 0.000 -6.859 0.000 6.859
2:LOAD CASE 0.000 -56.551 0.000 56.551
3:Generated Br 0.000 -88.774 0.000 88.774
6 6 1:LOAD CASE 0.000 -6.859 0.000 6.859
2:LOAD CASE 0.000 -56.551 0.000 56.551
3:Generated Br 0.000 -88.774 0.000 88.774
7 1:LOAD CASE 0.000 -6.560 0.000 6.560
2:LOAD CASE 0.000 -54.036 0.000 54.036
3:Generated Br 0.000 -84.834 0.000 84.834
7 7 1:LOAD CASE 0.000 -6.560 0.000 6.560
2:LOAD CASE 0.000 -54.036 0.000 54.036
3:Generated Br 0.000 -84.834 0.000 84.834
8 1:LOAD CASE 0.000 -5.686 0.000 5.686
2:LOAD CASE 0.000 -46.695 0.000 46.695
3:Generated Br 0.000 -73.334 0.000 73.334
8 8 1:LOAD CASE 0.000 -5.686 0.000 5.686
2:LOAD CASE 0.000 -46.695 0.000 46.695
3:Generated Br 0.000 -73.334 0.000 73.334
9 1:LOAD CASE 0.000 -4.303 0.000 4.303
2:LOAD CASE 0.000 -35.144 0.000 35.144
3:Generated Br 0.000 -55.226 0.000 55.226
9 9 1:LOAD CASE 0.000 -4.303 0.000 4.303
2:LOAD CASE 0.000 -35.144 0.000 35.144
3:Generated Br 0.000 -55.226 0.000 55.226
10 1:LOAD CASE 0.000 -2.518 0.000 2.518
2:LOAD CASE 0.000 -20.410 0.000 20.410
3:Generated Br 0.000 -32.099 0.000 32.099
10 10 1:LOAD CASE 0.000 -2.518 0.000 2.518
2:LOAD CASE 0.000 -20.410 0.000 20.410
3:Generated Br 0.000 -32.099 0.000 32.099
11 1:LOAD CASE 0.000 0.000 0.000 0.000
2:LOAD CASE 0.000 0.000 0.000 0.000
3:Generated Br 0.000 0.000 0.000 0.000

Print Time/Date: 02/05/2021 02:17 STAAD.Pro V8i (SELECTseries 5) 20.07.10.64 Print Run 3 of 3

You might also like