Omni ision

Advanced Information
® Preliminary Datasheet

OV2640FSL Color CMOS 2.0 MegaPixel Camera Module with OmniPixel2TM Technology

General Description Applications

• Cell phones
The OV2640FSL is a sensor on-board camera and lens
• PDAs
module designed for mobile applications where low power
consumption and small size are of utmost importance. • Picture phones
• Vision toys
Proprietary sensor technology utilizes advanced
algorithms to cancel Fixed Pattern Noise (FPN), eliminate Key Specifications
smearing, and drastically reduce blooming. All required Array Size UXGA 1600 x 1200
camera functions are programmable through the serial Core 1.3VDC + 5%
SCCB interface. Power Supply Analog 2.5 ~ 3.0VDC
I/O 1.7V to 3.3V
The device can be programmed to provide image output 125 mW (for 15 fps, UXGA
in various fully processed and encoded formats. YUV mode)
Power Active
140 mW (for 15 fps, UXGA
Requirements compressed mode)
The OV2640FSL features the OV2640 CAMERACHIP™
sensor. Refer to the OV2640 Datasheet for chip-specific Standby 600 µA
• YUV(422/420)/YCbCr422
information.
• RGB565/555
Output Formats (8-bit)
• 8-bit compressed data
Caution: READ THIS FIRST! • 8-/10-bit Raw RGB data
Prior to finalizing any mechanical or Optical Format 1/4"
electrical design for production, consult Chief Ray Angle 25° non-linear
with OmniVision to confirm any final Maximum UXGA/SXGA 15 fps
dimensional or electrical pinout data. Image SVGA 30 fps
Transfer Rate CIF 60 fps
Sensitivity 0.6 V/Lux-sec
Features S/N Ratio 40 dB
Dynamic Range 50 dB
• UXGA/SXGA and any size scaling down from SXGA Scan Mode Progressive
to 40x30 Maximum Exposure Interval 1247 x tROW
• Output support for Raw RGB, RGB (RGB565/555), Gamma Correction Programmable
YUV (422/420), YCbCr (4:2:2) formats, and 8-bit Pixel Size 2.2 µm x 2.2 µm
compressed data Dark Current 15 mV/s at 60°C
• 8mm x 8mm x 5.85mm module size Well Capacity 12 Ke
Fixed Pattern Noise <1% of VPEAK-TO-PEAK
• Flex cable connector
Image Area 3590 µm x 2684 µm
• 2.8V operation, low power dissipation Package Dimensions 8mm x 8mm x 5.85mm
• Serial Camera Control Bus (SCCB) interface
• Function controls: Figure 1 OV2640FSL Pin Diagram
– Exposure control
PIN 1
– Gain 1 STROBE
2 AGND
– White balance 3
4
SIOD
AVDD
5 SIOC
– Hue control 6
7
RESETB
VSYNC
8 PWDN
– Windowing 9
10
HREF
DVDD
11 DOVDD
12 DATA9
OV2640FSL 13 XCLK

Ordering Information 14
15
16
DATA8
DGND
DATA7
17 PCLK
18 DATA6
19 DATA2
Product Package 20
21
DATA5
DATA3
22 DATA4
NOTE: When using Molex connectors, disregard 23 DATA1
OV02640-FSL0 8mm x 8mm x 5.85mm Flex Cable Molex pin 1 indicator and use OVT pinout 24 DATA0

for PCB layout

PIN 24 2640FSL_FDS_001

© 2006 OmniVision Technologies, Inc. OmniVision and the OmniVision logo are registered trademarks of OmniVision Technologies, Inc.
Version 1.3, September 11, 2006 OmniPixel2 and CameraChip are trademarks of OmniVision Technologies, Inc.
These specifications are subject to change without notice.
OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Functional Description
Figure 2 shows the functional block diagram of the OV2640FSL Camera Module. The OV2640FSL includes:
• 1/4" lens
• OV2640 CAMERACHIP image sensor
• Flex cable

Figure 2 Functional Block Diagram

YUV/YCbCr, RGB565/555,
RGB Raw Data, compressed data

Image HREF/HSYNC
Photo Diode Data Output
Lens Processor
VSYNC

PCLK

XCLK1 RESETB PWDN SIOC SIOD 2640FSL_FDS_002

Figure 3 Module Schematic

NEC(TEESVJ0J475M8R)

DVDD DVDD JP1

1.3V 1.3V STROBE
AGND 1
4.7μF-0603

SIOD 2
3
DATA9
DATA8
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DGND

AVDD
SIOC 4
C2 RESETB 5
6

Flex Cable To Molex 52437-2491

DOVDD V SYNC
PWDN 7
HREF 8
EVDD DVDD 9
DOVDD 10
11
G6

G5

G4

G3

G2

G1

DATA9
E5
F6

F5

F4

F3

F2

XCLK 12
C1 0.1μF-0201 DATA8 13
DVDD

DGND
DVDD
EVDD
D9
D8
D7
D6
D5
D4
D3
D2

DGND 14
DATA7 15
DGND PCLK 16
E6 DGND EVDD F1 17
E4 DGND DATA6
EGND DATA1 DATA2 18
D1 E1 19
E2 DATA0 DATA5
U1 D0 PCLK DATA3 20
PCLK E3 21
D2 V SYNC DATA4
VSYNC HREF DATA1 22
HREF C3 23
OV2640 C2 SIOC DOVDD DATA0
SIOC SIOD 24
SIOD C1
C4 XCLK
XVCLK
DOVDD B1
D6 NC DOGND A1
STROBE
RESETB

EXPSTB
VREFN
VREFH
PWDN

SGND

AGND
SVDD

SVDD

AVDD

FREX

C6 0.1μF-0201
DGND
C6
B6
A6
B5
A5
C5
A4
B4
A3
B3
A2
B2

AVDD NOTE:
SVDD
Connector PWDN should be connected to ground if unused.
Sensor reset pin RESETB is active low.
AVDD is 2.8V sensor analog power.
STROBE
RESETB

DVDD is 1.3V sensor digital power.

VREFN
VREFH
PW DN

C3 C4 C5 DOVDD is 1.8V to 3.0V sensor digital IO power.

1.0μF-0402 0.1μF-0201 0.1μF-0201 Sensor AGND and DGND should be separated and connected to a
single point outside PCB (DO NOT connect inside module).
C1, C2 should be close to sensor DVDD and DGND.
C3 should be close to sensor SVDD, AVDD and AGND.
C4 should be close to sensor VREFH and AGND.
C5 should be close to sensor VREFN and AGND.
C6 should close to sensor DOVDD and DGND.
C7 should close to sensor EVDD and DGND.
D[9:2] is module YUV and RGB 8-bit output (D9: MSB, D2: LSB).
D[9:0] is module raw RGB 10-bit output (D9: MSB, D0: LSB).
2640FSL_FDS_003

2 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Functional Description

Imaging Specifications

Table 1 Sensor Image Functions

Sensor Imaging Functions Description

Auto Exposure Module automatically sets correct exposure time.

Auto Exposure ON/OFF Auto exposure can be turned off so the exposure can be set manually.

Auto White Balance (AWB) AWB without companion processor interaction.

Auto White Balance OFF AWB can be turned off.

Electrical Illumination Flicker Interference from 50Hz or 60Hz illumination can be suppressed with manually set
Elimination frame rate divider.

Size can be altered using the windowing registers. Quarter-format sub-sampling is

Image Size Decimation
also provided.

Image ON/OFF Image ON/OFF can be controlled by register settings.

Vertical Flip Transposes the top and bottom sides of the image.

RGB Output RGB raw data output available.

AGC Gain Automatic Gain Control (AGC)

White Balance Automatic White Balance

NOTE: OV2640FSL features the OV2640 CAMERACHIP sensor. Refer to the OV2640 Datasheet for chip-specific information.

Table 2 Output Specifications

Output Image Formats Description

UXGA (1600 x 1200 pixels)

SXGA (1280 x 1024)

Output Formats
SVGA (800 x 600 pixels)

CIF (400 x 292 pixels)

RGB Raw Format 8-bit or 10-bit

YUV Format 4:2:0 or 4:2:2 compliant with CCIR656

YUV Order YUYV or UYVY

Embedded Sync Codes Sync signals coded in with data output (CCIR656) or output separately.

Data Clipping According to CCIR656 or no clipping.

Format in Decimation Mode PCLK verifies whether or not there is data on every cycle.

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 3

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Pin Description

Table 3 Module Pin Description

Pin Number Name Pin Type Function/Description

01 STROBE I/O Flash control output

02 AGND Power A/D converter ground, array decoder ground

03 SIOD I/O SCCB serial interface data I/O

04 AVDD Power 2.8 V supply for A/D converter and array decoder

05 SIOC Input SCCB serial interface clock input

06 RESETB Input (0) Chip reset, active low

07 VSYNC Output Vertical synchronization output when chip is in master mode

08 PWDN Input (0)a Power down mode enable, active high

09 HREF Output Horizontal reference output

10 DVDD Power 1.3 V supply for digital circuits

11 DOVDD Power 2.8 V supply for digital video port

12 DATA9 Output Video port output bit[9]

13 XCLK1 Input Crystal clock input

14 DATA8 Output Video port output bit[8]

15 DGND Power Digital video port ground

16 DATA7 Output Video port output bit[7]

17 PCLK Output Pixel clock output

18 DATA6 Output Video port output bit[6]

19 DATA2 Output Video port output bit[2]

20 DATA5 Output Video port output bit[5]

21 DATA3 Output Video port output bit[3]

22 DATA4 Output Video port output bit[4]

23 DATA1 Output Video port output bit[1]

24 DATA0 Output Video port output bit[0]

a. Input (0) represents an internal pull-down low resistor.

4 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Electrical Characteristics

Electrical Characteristics
Table 4 Absolute Maximum Ratings
Ambient Storage Temperature -40ºC to +95ºC

VDD-A 4.5V

Supply Voltages (with respect to Ground) VDD-C 3V

VDD-IO 4.5V

All Input/Output Voltages (with respect to Ground) -0.3V to VDD-IO+1V

NOTE: Exceeding the Absolute Maximum ratings shown above invalidates all AC and DC electrical specifications and may
result in permanent device damage.

Table 5 DC Characteristics (-30°C < TA < 70°C)

Symbol Parameter Min Typ Max Unit

Supply

VDD-A Supply voltage 2.5 2.8 3.0 V

VDD-D Supply voltage 1.24 1.3 1.36 V

VDD-IO Supply voltagea 1.71 2.8 3.3 V

IDDA-A Active (Operating) Currentb 30 40 mA

25 (YUV) 35 (YUV)
IDDA-D Active (Operating) Currentb mA
35 (Compressed) 50 (Compressed)

IDDA-IO Active (Operating) Currentb 6 10 mA

IDDS-SCCB 1 2 mA
Standby Currentb
IDDS-PWDN 600 1200 µA

Digital Inputs

VIL Input voltage LOW 0.54 V

VIH Input voltage HIGH 1.26 V

CIN Input capacitor 10 pF

Digital Outputs (standard loading 25 pF)

VOH Output voltage HIGH 1.62 V

VOL Output voltage LOW 0.18 V

Serial Interface Inputs

VIL SIO_C and SIO_D -0.5 0 0.54 V

VIH SIO_C and SIO_D 1.26 1.8 2.3 V

a. 1.8V I/O is supported. Contact your local OmniVision FAE for further details.
b. VDD-A = 2.8V, VDD-D = 1.3V, and VDD-IO = 1.8V for 15 fps in UXGA mode
IDDS-SCCB refers to SCCB-initiated Standby, while IDDS-PWDN refers to PWDN pin-initiated Standby

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 5

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Table 6 AC Characteristics (TA = 25°C, VDD-A = 2.8V)

Symbol Parameter Min Typ Max Unit

ADC Parameters

B Analog bandwidth 20 MHz

DLE DC differential linearity error 0.5 LSB

ILE DC integral linearity error 1 LSB

Settling time for hardware reset <1 ms

Settling time for software reset <1 ms

Settling time for UXGA/SVGA mode change <1 ms

Settling time for register setting <300 ms

Table 7 Timing Characteristics

Symbol Parameter Min Typ Max Unit

Oscillator and Clock Input

fOSC Frequency (XCLK) 6 24 MHz

tr, tf Clock input rise/fall time 5 ns

Clock input duty cycle 45 50 55 %

6 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Timing Specifications

Timing Specifications

Figure 4 SCCB Interface Timing Diagram

tF t HIGH tR
tLOW
SIOC

t HD:STA t HD:DAT t SU:DAT

tSU:STA tSU:STO

SIOD IN

t BUF
tAA t DH
SIOD OUT
2640FSL_FDS_004

Table 8 SCCB InterfaceTiming Specifications

Symbol Parameter Min Typ Max Unit

fSIO_C Clock Frequency 400 KHz

tLOW Clock Low Period 1.3 µs

tHIGH Clock High Period 600 ns

tAA SIOC low to Data Out valid 100 900 ns

tBUF Bus free time before new START 1.3 µs

tHD:STA START condition Hold time 600 ns

tSU:STA START condition Setup time 600 ns

tHD:DAT Data-in Hold time 0 µs

tSU:DAT Data-in Setup time 100 ns

tSU:STO STOP condition Setup time 600 ns

tR, tF SCCB Rise/Fall times 300 ns

tDH Data-out Hold time 50 ns

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 7

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Figure 5 UXGA, SVGA, and CIF Line/Pixel Output Timing

tp t pr t pf

PCLK or
MCLK

t dphr t dphf

HREF

t su t hd

Invalid
D[9:0] P1599/799/399 P0 P1 P2 P 1598/798/398 P1599/799/399
Data

t dpd 2640FSL_FDS_005

Table 9 Pixel Timing Specifications

Symbol Parameter Min Typ Max Unit

tp PCLK period 27.78 ns

tpr PCLK rising time 3.5 ns

tpf PCLK falling time 2.2 ns

tdphr PCLK negative edge to HREF rising edge 0 5 ns

tdphf PCLK negative edge to HREF negative edge 0 5 ns

tdpd PCLK negative edge to data output delay 0 5 ns

tsu Data bus setup time 15 ns

thd Data bus hold time 8 ns

8 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Timing Specifications

Figure 6 UXGA Frame Timing

1248 x tLINE

VSYNC

4 x tLINE 27193 tP tLINE = 1922 tP 57697 tP

322 tP

HREF

1600 tP
189 tP 80 tP

HSYNC

D[9:0] Invalid Data

P0 - P1599
Row 0 Row 1 Row 2 Row 1199 2640FSL_FDS_006

Figure 7 SVGA Frame Timing

672 x tLINE

VSYNC

4 x tLINE 7415 tP tLINE = 1190 tP 73895 tP

390 tP

HREF

800 tP
179 tP 80 tP

HSYNC

D[9:0] Invalid Data

P0 - P799
Row 0 Row 1 Row 2 Row 599 2640FSL_FDS_007

Figure 8 CIF Mode Frame Timing

336 x tLINE

VSYNC

4 x tLINE 3707.5 tP tLINE = 595 tP 17907.5 tP

195 tP

HREF

400 tP
89.5 tP 40 tP

HSYNC

D[9:0] Invalid Data

P0 - P399
Row 0 Row 1 Row 2 Row 295 2640FSL_FDS_008

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 9

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Figure 9 Frame Exposure Mode Timing with EXPST_B Staying Low

Shutter Open

Shutter
"Flash Turn ON"
FREX
t line
Exposure Time
Sensor
Sensor Timing Precharge

t dfvr
VSYNC
4xt LINE tdhv 4xt LINE
HREF

D[9:0]
No following live video
Row X Row 0 Row 1 Row 1199
frame if set to transfer
single frame
2640FSL_FDS_009

Figure 10 Frame Exposure Mode Timing with EXPST_B Asserted

Shutter Open

Shutter

FREX
t des tdef
"Flash Turn ON"
EXPST_B
t pre
Exposure Time
Sensor
Sensor Timing Precharge

t dfvr
VSYNC
4xt LINE tdhv 4xt LINE
HREF

D[9:0]
No following live video
Row X Row 0 Row 1 Row 1199
frame if set to transfer
single frame
2640FSL_FDS_010

Table 10 Frame Exposure Timing Specifications

Symbol Min Typ Max Unit

tline 1922 (UXGA) tp

tvs 4 tline

tdfvr 8 9 tp

tdfvf 4 tline

tdvsc 2 tline

tdhv 38964 (UXGA) tp

tdvh 15928 (UXGA) tp

tdhso 0 ns

tdef 20 tp

tdes 8 1900 (UXGA) tp

NOTE 1) FREX must stay high long enough to ensure the entire sensor has been reset.
2) Shutter must be closed no later then 3896 tp after VSYNC falling edge.

10 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Package Specifications

Package Specifications
Refer to Figure 11 for package information on the OV2640FSL module.

Figure 11 OV2640FSL Package Specifications

8.0 Stiffener

7.0

12.50

7.9 R0.5
FPC
5.40

7.00
Lens

Holder

5.85±0.30 0.27

Stiffener 0.14

Pin 1

5.40 2x0.50
24x0.30

0.50
(Pitch)
11.50 12.50

3.00
0.15

2640FSL_FDS_011

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 11

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Mechanical Specifications

Table 11 Mechanical Dimensions

Parameter Specification Comments

Sensor 6.30 mm x 6.32 mm CMOS in housing

Lens Plastic

Connection Type 24 x 0.5 mm Flex cable

Housing 8.0 mm x 8.0 mm x 5.85 mm Excluding mushroom

Connector Information

The OV2640FSL uses a 24-pin, 0.5 mm pitch flex cable connector. Table 12 shows a listing of some recommended
connectors.

Table 12 Recommended Connectors

Manufacturer Part No. Description

52437-2427 (Bulk)
Molex 0.5 FPC Connector ZIF for SMT, R/A (bottom contact)
52437-2491 (Tape reel)

Optical Specifications

Table 13 Optical Specifications

Parameter Specification Comments

Lens Elements 4-element plastic Fixed focus

Viewing Angle 59.9° diagonal

Focal Length 3.78 mm

F Number 2.8

Focus Range 60 cm → ∞ Allowable blur size: 4.4 µm

Filter IR cut Included

Mount Description M7 x 0.35P

TV Distortion <1%

Focus Adjustment Fixed At 1.2 m

12 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision Handling Precautions

Handling Precautions

WARNING: READ THIS FIRST!

Prior to handling any OmniVision flex camera module, read the following
precautions.

• DO NOT try to open the unit enclosure as there is no user-serviceable component inside.
• To prevent damage to the camera module by electrostatic discharge, handle the camera module
ONLY after discharging ALL static electricity from yourself and ensuring a static-free environment
for the camera module.
• DO NOT touch the top surface of the lens.
• DO NOT press down on the lens.
• DO NOT try to focus the lens.
• DO NOT put the camera module in a dusty environment.
• To reduce the risk of electrical shock and damage to the camera module, turn OFF the power
before connect and disconnect the camera module.
• DO NOT bend the flex cable in a sharp angle.
• DO NOT twist the flex cable.
• DO NOT peel the flex cable when you install and uninstall the camera module.
• DO NOT drop the camera module more than 60 cm onto any hard surface.
• To prevent fire or shock hazard, DO NOT expose camera module to rain or moisture.
• DO NOT expose camera module to direct sunlight.
• DO NOT put camera module in a high temperature environment.
• DO NOT use liquid or aerosol cleaners to clean the lens.
• DO NOT make any changes or modifications to camera module.
• DO NOT subject camera module to strong electromagnetic field.
• DO NOT subject the camera module to excessive vibration or shock.

Version 1.3, September 11, 2006 Proprietary to OmniVision Technologies, Inc. 13

OV2640FSL Color CMOS 2.0 MegaPixel (OmniPixel2™) Camera Module Omni ision

Note:

• All information shown herein is current as of the revision and publication date. Please refer
to the OmniVision web site (http://www.ovt.com) to obtain the current versions of all
documentation.

• OmniVision Technologies, Inc. reserves the right to make changes to their products or to
discontinue any product or service without further notice (It is advisable to obtain current product
documentation prior to placing orders).

• Reproduction of information in OmniVision product documentation and specifications is

permissible only if reproduction is without alteration and is accompanied by all associated
warranties, conditions, limitations and notices. In such cases, OmniVision is not responsible
or liable for any information reproduced.

• This document is provided with no warranties whatsoever, including any warranty of

merchantability, non-infringement, fitness for any particular purpose, or any warranty
otherwise arising out of any proposal, specification or sample. Furthermore, OmniVision
Technologies, Inc. disclaims all liability, including liability for infringement of any proprietary
rights, relating to use of information in this document. No license, expressed or implied, by
estoppels or otherwise, to any intellectual property rights is granted herein.

• ‘OmniVision’ and the OmniVision logo are registered trademarks of OmniVision Technologies, Inc.
’OmniPixel2’ and ’CameraChip’ are trademarks of OmniVision Technologies, Inc. All other
trade, product or service names referenced in this release may be trademarks or registered
trademarks of their respective holders. Third-party brands, names, and trademarks are the
property of their respective owners.

For further information, please feel free to contact OmniVision at [email protected].

OmniVision Technologies, Inc.

1341 Orleans Drive
Sunnyvale, CA USA
(408) 542-3000

14 Proprietary to OmniVision Technologies, Inc. Version 1.3, September 11, 2006

Omni ision TM

REVISION CHANGE LIST

Document Title: OV2640FSL Flex Module Datasheet Version: 1.0

DESCRIPTION OF CHANGES
Initial release
Omni ision TM

REVISION CHANGE LIST

Document Title: OV2640FSL Flex Module Datasheet Version: 1.1

DESCRIPTION OF CHANGES
The following changes were made to version 1.0:
• In Table 5 on page 5, made the following changes:
– Added “40 mA” for Maximum specification of IDDA-A
– Added “35 mA (YUV)” and “50 mA (Compressed)” for Maximum specification of
IDDA-D
– Added “10 mA” for Maximum specification of IDDA-IO
– Added “2 mA” for Maximum specification of IDDS-SCCB
– Added “1200 µA” for Maximum specification of IDDS-PWDN
• Changed module schematic in Figure 3 on page 2.
Omni ision TM

REVISION CHANGE LIST

Document Title: OV2640FSL Flex Module Datasheet Version: 1.2

DESCRIPTION OF CHANGES
The following changes were made to version 1.1:
• Under Key Specifications on page 1, changed specification for Core Power Supply from
“1.2VDC ± 5%” to “1.3VDC ± 5%”
• In Figure 3 on page 2, changed DVDD voltage callouts (2 places) from “1.2V” to “1.3V”
• In Figure 3 on page 2, changed 4th line under Notes from “DVDD is 1.2V sensor digital
power” to “DVDD is 1.3V sensor digital power”
• In Table 3 on page 4, changed description of pin 10 (DVDD) from “1.2V supply for digital
circuits” to “1.3V supply for digital circuits”
• In Table 5 on page 5, changed Min, Typ, and Max for Supply voltage (VDD-D) from
“1.14”, “1.2”, and “1.26” to “1.24”, “1.3”, and “1.36”
• In Table 5 on page 5, changed table footnote b from “VDD-A = 2.8V, VDD-D = 1.2V, ...” to
“VDD-A = 2.8V, VDD-D = 1.3V, ...”
Omni ision TM

REVISION CHANGE LIST

Document Title: OV2640FSL Flex Module Datasheet Version: 1.3

DESCRIPTION OF CHANGES
The following changes were made to version 1.2:
• In Figure 1 on page 1, added “Note: When using Molex connectors, disregard Molex pin 1
indicator and use OVT pinout for PCB layout.”
• In Table 12 on page 12, added table footnote a “When using Molex connectors, disregard
Molex pin 1 indicator and use OVT pinout for PCB layout.”
• In Table 13 on page 12, changed Lens Elements specification from “3-element plastic” to
“4-element plastic”
• In Table 13 on page 12, changed Focus Range specification from “80 cm → ∞” to
“60 cm → ∞” and added “Allowable blur size: 4.4 µm” under Comments
• In Table 13 on page 12, added “At 1.2 m” under Comments for the Focus Adjustment
specification