TEСHNIСАL

САTАLOG
CONTENTS
RIMERA
About the Company........................................................................................................................................................................................................................................3

RIMERA — SERVICE
Service and Lease for ESP and Surface Equipment ..........................................................................................................................................................................4
Tubing Services .................................................................................................................................................................................................................................................5
Well Survey.........................................................................................................................................................................................................................................................6

RIMERA — ALNAS
ESP equipment for oil production.............................................................................................................................................................................................................8

RIMERA — IZHNEFTEMASH
Equipment for Artificial Lift, Development and Overhaul for Oil and Gas Wells........................................................................................................... 24

1
INTRODUCTION

2
 INTRODUCTION

ABOUT THE COMPANY

1 2
Oil production equipment Servicing oil and gas production
equipment

ALNAS RIMERA-SERVICE
IZHNEFTEMASH

Developing these business directions allows Rimera Group to form a unique integrated proposal for the Russian oil and gas industry
in oilfield development from penetration into a deposit to construction of its surface and subsurface equipment and an access to
transport pipelines.

THE BUSINESS OF OIL PRODUCTION EQUIPMENT INVOLVES THE LEADING ENTERPRISES OF THE SECTOR:

Rimera-Service — provider of end-to-end service solutions for artificial lift wells in the major oil production regions of the Russian
Federation: Nizhnevartovsk, Nyagan, Talinka, Noyabrsk, Muravlenko and Buguruslan

Alnas — production of electric submersible centrifugal pumping systems for oil production.

Izhneftemash — production of oil and gas equipment for drilling, completion and repair of oil and gas wells, as well
as for oil production.

3
ABOUT RIMERA-SERVICE
The service centers are located in the nation's major oil production regions. Extensive geographic coverage, state-of-the-art equipment,
and highly skilled personnel combine to provide an unmatched service offering for production companies based on win-win partner-
ships. One in seven production wells with electric submersible pumps operated in Russia is serviced by Rimera-Service.

The company offers oil production companies a range of solutions using advanced technologies and state-of-the-art equipment.
Alnas products are certified for conformance to Russia’s most rigorous quality standards. All equipment is available in customized
configurations tailored to specific needs of customers.

ESP AND SRP UNIT DOWNHOLE EQUIPMENT SERVICE AND LEASE

• ESP unit size selection for operation in a specified well

• Acceptance control, testing, revision, maintenance and overhaul of ESP unit
assemblies
• Onsite delivery of ESP units for installation and commissioning using own motor
transport
• Surface equipment repair
• Preventive maintenance of surface equipment
• Repair and setup of all types of ESP unit control stations and transformers
• ESP unit assemblies follow-up, operation analysis, failure cause analysis
• Equipment fault detection, mean-time-between-failures account by separate
assemblies and their state

MAINTENANCE AND OVERHAUL OF ESP UNITS

Restoration of ESP unit operability, with up to 75% ESP components to be replaced

(maintenance), or with over 75% working parts to be replaced with new ones
(overhaul). Operations can be executed both within the service framework or under a
repair work contract.

SRP & PUMPING ROD MAINTENANCE AND OVERHAUL

SRP disassembly, fault detection, re-assembly, equipment testing, and spare parts
provision.

CABLE LINE REPAIR

• Cable line fault detection

• Armor scuffing and low isolation areas removal
• Cable joints arrangement and dismantling, cable complete with thermal inserts
and new cable segments integration according to approved arrangement for well
conditions
• MLE splicing and cable line testing with high-voltage tests report generation

CABLE LINES AND MLE MANUFACTURING

Rental term duration for submersible ESP parts is 3 years and 5 years
for surface parts. SRP lease term – 3 years

4
 ABOUT RIMERA-SERVICE

CONTROL STATION ( VSD) REPAIR AND MODERNIZATION

Case painting, application of graphic inscriptions & signs

New module mounting in CS body
CS testing

SUPERVISING OF WELL SERVICING OPERATIONS

Visual monitoring of well servicing team operations for well preparation and
tripping
operations with ESP units.

TRAINING AND CONSULTATION

ESP & SRP learning and operation training is provided by specialists in classrooms
and in workshops. Methodological literature, operating manuals, stands displaying
ESP & SRP parts, including cutaway view, are provided. Training classes are
equipped with a well head model and a complete set of surface equipment (VSD
and Step-Up Transformer) allowing to learn ESP unit mounting & installation,
startup and steady-state flow process.

Tubing services
OCTG REPAIR, PREPARATION TO OPERATION, AND GATHERING

In the process of work pipe preparation and gathering by customer requests

is performed basing on the following parameters set: pipe schedule, strength
group, length of suspension. The further completed suspension is delivered to
the customer's field. In case of out-of-spec product supply, claims work with
manufacturer and pipe repair are carried out.

MANUFACTURING PRODUCTION ACCESSORIES FOR OILFIELD EQUIPMENT

The following types of production accessories are manufactured: reducers (for

transition from one pipe schedule to another), sleeves and landing joints of various
lengths (for lowering submersible equipment to set depths).

PIPE HANDLING AND STORAGE SERVICES

The enterprise has a railway dead-end track with handling machinery

(one-time unloading area of 850 tons). Opened and closed storage areas
are over 27,000 m2.

OTHER SERVICES

Submersible equipment infield service includes equipment delivery, equipment

follow-up, monthly report reception and verification, realization of equipment
primary account, equipment repair.

Supervising includes periodic inspection at contract organizations carrying out well

repair, participation in accident investigation commissions, auditing, claims works.

Tubing string lease for hydraulic fracturing and process operations allows
contractors carrying out well repair to render these services to customers without
acquiring an expensive equipment.

5
ABOUT RIMERA-SERVICE

Well survey

GEOTECHNICAL SURVEY

In the process of work, drilling parameters and drilling fluid are monitored, content of hydrocarbons and other fluids coming from tapped
strata are determined, cuttings sampling and sludge assay are performed, on-rig proximate wellcore analyses are performed.

OPEN HOLE SURVEY

The survey scope includes the following jobs:

• Lithological differentiation of geological cross section exposed by electrologging
• Reservoir bed identification
• Reservoir bed fluid content identification
• The rocks composing a geological cross-section have different specific electrical resistance depending on lithological structure
and reservoir bed fluid content. Reservoir porosity and permeability properties identification.

OPEN HOLE SURVEY DURING WELL CONSTRUCTION

Complete well-logging operations provide geologic problem solving via three runs of nuclear logging tools and acoustic logging tools:
• Lithological differentiation of geological cross section with its subsequent correlation
• Reservoir bed identification
• Reservoir properties assessment (porosity, shaliness, and permeability)
• Reservoir bed fluid content estimation
• WOC, GOC, GWC identification with subsequent perforation interval referencing
For boring casing state examination, the acoustic cement bond logging, defectometry, thermometry, gamma defectometry and thickness
testing, electromagnetic collar logging, electromagnetic testing, acoustic logging, and mechanical pipe profile logging are used

PERFORATING-EXPLOSIVE OPERATIONS

These include different-purpose perforating-explosive operations performed in deep wells with the use of blasting powders, brisants,
and other explosives. Using explosions permits to control accident damage, to restore circulation, to break down, jar, twist off, shear a
drill string, to break up and to occasionally recover metal pieces left in the hole, to prevent sticking, and to perform other operations,
which are often quite specific.
All kinds of works using explosives, such as perforation of strings, straddle packer setting, hole torpedoing, gunpowder pressure genera-
tors, etc.

PERFORATION (CABLE AND TUBING CONVEYED)

Cumulative perforation provides hydraulic connection between a well and layer, i.e., perforation channel must break through the casing,
cement ring, mud and grout colmatation area, and penetrate to a good part of the layer.

TORPEDOING

For accident elimination during boring, the following is made:

• Boring tool sticking interval detection
• Stuck pipe recovery by blasting methods
• Break or cutting of tubing and casing
• Detection of metal objects lost in the hole
• Liquidation of foreign objects in the hole and bottomhole cleaning
• Using cable devices to set dividing and isolating bridges in borehole

6
 ABOUT RIMERA-SERVICE

WELL TESTING

Geophysical researches for studying productive layers during their test, development and exploitation, at displacement agent pumping
to acquire information on productivity, filtration properties, and also layers connectivity, including pressure, temperature, flow rate, fluid
composition and properties, as measured in borehole using apparatus run in a well on logging cable.

DEVELOPMENT CONTROL, OPERATING WELL DIAGNOSIS

• Researching process of oil and gas oil displacement in a layer to monitor reserve recovery and estimate an efficiency of enhanced
oil recovery methods applied
• Field-performance data determination
• Well researches to choose optimum operating mode for process equipment
• Actual well design clarification
• Casing and cement ring condition monitoring, detection of casing leaks, cement, casing-annulus crossflows for repair planning
• Water inflow interval determination
• Tubing condition monitoring and lifting equipment
• Repair information support, special study during various process operations
• Process operations on setting dividing bridges, plugs, on completion and stimulation
• Monitoring and documenting repair results for well history

7
ABOUT ALNAS
Alnas-manufactured electrical submersible pump units produce one-third of all Russian oil, operating successfully at oil fields of major
companies in Russia and overseas. Alnas products are exported to Kazakhstan, Azerbaijan, Ukraine, Belarus, Uzbekistan, Lithuania,
Turkmenistan, Venezuela, Oman and India.

The company offers oil production companies a range of solutions using advanced technologies and state-of-the-art equipment.
Alnas products are certified for conformance to Russia’s most rigorous quality standards. All equipment is available in customized
configurations tailored to specific needs of customers.

ALNAS IN BRIEF:

• Innovative research and development

• A group of manufacturing enterprises which fabricate complete submersible systems
(centrifugal pump, gas separator, seal section, motor, surface electrical equipment)
• Expertise in selecting equipment for various operating conditions
• Repairs and maintenance of submersible oil production equipment

QUALITY

The plant has implemented a quality management system and an environment management system:

• Our quality management system (QMS) is conformant to GOST R ISO 9001 – Quality Management Systems. Requirements.
• Our quality management system for automotive production (QMS-A) conforms to ISO/TS 16949 – Quality Management Systems.
Particular Requirements for the Application of ISO 9001:2008 for Automotive Production and Relevant Service Part Organiza-
tions.
• Our environment management system (EMS) conforms to GOST R ISO 14001 Environmental management systems — Require-
ments with guidance for use.

8
 ABOUT ALNAS

RESEARCH AND DEVELOPMENT

Alnas Engineering Center is a joint research and development

facility committed to high standards of mechanical engineering for the petro-
leum industry.
Products of our engineering efforts in recent years:
• 63 types of new pumps
• 38 new and 6 upgraded submersible electric motors
• 15 types of seal section, 2 new dispersing inlet modules
• Over 30 new technical solutions patented

AFTER-SALES SUPPORT OF PRODUCTS

Alnas uses an integrated approach in dealing with customers, which includes both manufacture and servicing of equipment. This ena-
bles oil companies to operate it with maximum efficiency and keep oil production costs to a minimum.

Rimera Group includes Rimera-Service LLC with its extensive chain of service operations based in Russia’s largest oil production
regions: Khanty-Mansiysk Autonomous Area – Ugra (Nizhnevartovsk, Surgut, Singapai, Talinka), Yamalo-Nenets Autonomous Area
(Gubkinskiy), Orenburg Region (City of Buguruslan).

OUR SERVICE OFFERING INCLUDES:

• Selecting equipment to match well operating conditions

• Starting wells and ramping up to a steady-state mode
• Installing and removing surface operating equipment and subsurface operating equipment of the electric centrifugal pump units
• Routine and major repairs on surface operating equipment and subsurface operating equipment of the electric centrifugal pump
units
• Transportation of equipment and electric centrifugal pump units
• Preventative maintenance of surface operating equipment
• Acceptance inspections of surface operating equipment and subsurface operating equipment of the electric centrifugal pump
units
• Leasing electric centrifugal pump units to oil companies
• Personnel training
• Analyzing the performance of the production well stock
• Comprehensive maintenance and repairs of tubing

9
 ABOUT ALNAS
Submersible centrifugal pump systems

COMPLETE SETS OF SUBMERSIBLE CENTRIFUGAL

PUMP SYSTEMS (Alnas ESP UNITS )

Alnas products are submersible centrifugal pump systems (Alnas ESP units) used for oil
production. In general these systems include:

• Submersible centrifugal pump (including check valve and Bleeder valve, pump sections,
intake module or lower section depending on order)
• Sludge trap (option by request)
• Gas separator (option by request, unit supplied with gas separator is provided w/o intake
module)
• Slotted screen/intake module (option by request, complete PPFA unit is provided w/o
intake module)
• Seal section
• Submersible electric motor
• Cable line
• Surface electrical equipment (control station, transformer, etc.)
• Telemetry systems
• Tools, accessories, mounting & installation sets
• Spare parts (option by request)

The units are designed by Rimera R&D Department. Unit design is based on the state-of-the-
art technology and uses materials developed specifically for submersible equipment that also
have applications in the defense and space industries.
The unit allows pumping out reservoir fluid at the rate of 10 to 2,000 m3/day from the maximum
depth of 4,000 m. Units are supplied in any arrangement customized for a specific well.

Produced liquid is oil, associated water, and associated gas mixture having the
following characteristics:
• Maximum produced water content (%) – 99
• Produced water pH value is 5.0 to 8.5
• Maximum liquid density (kg/m3) – 1,400
• Single-phase liquid kinematic viscosity at which pump operation is provided without head and efficiency changing (mm2/s) – 1
• Maximum concentration of solids for pumps (g/l, mass%): –
standard make – 0.1 (0.01)
corrosion resistant make – 0.2 (0.02)
wear resistant and corrosion resistant makes – 0.5 (0.05)
enhanced corrosion and wear resistance – 1.0 (0.10)
pumps w/ fine filter – 3.0 (0.30)
• Mohs hardness number of particles for pumps, in grades:
standard, corrosion resistant make – 5
enhanced corrosion and wear resistance, wear-resistant and corrosion-resistant makes – 7
• Maximum free gas content at pump suction is 25 vol%, 55% when using gas separator, and 75% when using gas separator-dispens-
er, 30% when using intake module in the unit
• Maximum concentration of H2S for pumps (g/l, mass%):
standard, wear resistant make – 0.01 (0.001)
corrosion resistant, corrosion and wear resistant make,
enhanced corrosion and wear resistance – 1.25 (0.125)
• Maximum temperature of pumped out liquid, °С – 150
• Maximum hydrostatic pressure in the unit suspension area (MPa) – 40
• Aggressive component content, max: СО2 0.15 g/l, НСО3– 1 g/l, Cl– 20 g/l, Ca2+ 2 g/l (when using enhanced corrosion and wear
resistance, corrosion- and wear-resistant, and corrosion-resistant pumps).

10
 ABOUT ALNAS
Pumps

SUBMERSIBLE CENTRIFUGAL PUMPS (ESP )

The Alnas pumps are designed using sectional principle and consist of upper section (with fishing head for
fastening pump to tubing string), midsections, intake module, gas separator, and check valve and bleeder valve.

Check valves have high tightness permitting to conduct coil tubing pressure/leak test. Check valves design may
be poppet valve type or ball type (option by request).

Intake module may be provided with pump section as a whole to lower a number of connections. In that case,
the pump unit (complete) has a lower stage provided with perforations for liquid intake.

Intake submersible wire filter can also be used for submersible pumps to take formation fluid and separate
solid particles with cross-section of 0.1 or 0.2 mm. For detailed filter data, see Page 21.

At high gas content in formation fluid, complete pump may include a gas separator. When PPFA is included,
gas separator is made w/o intake openings.

Pump section length is varied to provide optimal pump selection for any wellbore length. Intermediate radial
bearings are installed along the section (see fig). Reliable and long pump operation under various operating
conditions is provided by optimum distance between radial bearings.

Impeller and guide vane materials developed by leading

specialized institutes are as follows:

Modified gray cast-iron (standard design Alnas ESP pumps)

Modified cast-iron of enhanced wear resistance (ESPW type

pump wear resistant types)
intermediate
ball check valve bearing
Ni-resist type iron (ESPC pump corrosion resistant type and
ESPCW pump corrosion and wear resistant type)

Hard Ni-resist type iron with max hardness of HB 240 (enhanced

corrosion and wear resistance pumps)

Polymeric materials with special compounds (pump types 23..

ESP (C, CW)). Impellers – polymer, guide vanes – composite (w/
polymer flow section) or full metal. High-strength and high-pre-
cision pump shafts are manufactured from stainless steel or
K-Monel/Inconel alloy. Various pump types permit supplying
high heat-, corrosion- and wear resistant modifications.

pump section bleeder

stage valve pump section

11
 ABOUT ALNAS
Pumps

DOUBLE-SEAT DESIGN PUMPS

Application of ESP with "double-seat design" pump stages allows pump operation at arduous conditions with high solids content. This
stage design provides significantly enhanced mean-time-between-failures for the ESP pumps.

High service life of "double-seat design" pump is conditioned by considerably lower friction loading per unit area of impellers
The stages are extended in both sides, which allows to:

• Reduce vibration (impeller stability enhanced due to multiple increased impeller fit length on a shaft)
• Hidden shaft providing its protection from formation fluid hydroabrasive effect
• Practically eliminate wedge key cutting and stage to shaft turning (impeller key slot length is multiply increased to minimize key
load).
Special materials used for operating in conditions of hydroabrasive wear – pump stages are made of Ni-resist or modified (non-
corrosion resistant) cast-iron of enhanced wear resistance.

Complete set of tools and accessories for in-field mounting & installation are available for order. All necessary spare parts can be
supplied in any amount required.

PUMPS WITHOUT AXIAL BEARING SHAFT

These pumps features are as follows:

• Axle loading transmitted by pump shaft is sustained by reinforced seal section thrust bearing assembly
• Mounting & installation is simplified as compared to competitors
• Section hydraulic efficiency is enhanced due to pump stage quantity increased
• Pump shaft cantilevers are reduced
• Section hydraulic efficiency is enhanced due to shaft axial bearing transferred from pump section to seal section cave and in-
creased number of pump stages in pump sections

Pumps without shaft axial bearing have the following advantages:

• Pump operating elements are of Ni-resist iron or Ni-resist type austenitic cold pig iron with hardness of HB 190 to 240 (option by
request)
• Radial bearings are manufactured using hard alloys
• Lower pump vibration level and radial bearings loading due to reduced shaft cantilevers

PUMPS WITH PACKET STAGE ASSEMBLY

Alnas offers pumps with packet stage assembly, enhanced corrosion and wear resistance, designed for reservoir fluid production in diffi-
cult operating conditions.

This pump type features are as follows:

• Pump sections without shaft axial bearing (transmitted shaft axle loading is sustained by thrust bearing).
• Packet stage assembling provides axial and radial support for every packet of stages
• Operating elements of single pad design w/ extended hub
• Impeller hubs contact each other and transfer axle loading to radial-axial support installed in stage packet lower part
• Shaft overhang is reduced relative to radial bearing
• Due to reduced base overall dimensions, the protective ribs for cable extension are removed from the base to the head

The benefits of pumps with packet stage assembly are as follows:

• Pump operating elements are of Ni-resist type austenitic cold pig iron, with hardness of HB 190 to 240, and high corrosion resistant
• Radial bearings are manufactured using hard alloys
• Low impeller washers wear
• Due to reduced shaft cantilever, pump unit total vibration level is reduced
• Protective ribs located in the head allow for cable protection from the very top of the section.

12
 ABOUT ALNAS
Pumps

SPECIAL DESIGN ESP

0215, 2215 CORROSION AND WEAR RESISTANT SERIES 0615 COMPRESSION SERIES TYPE

New 0215, 0615 and 2215 series pumps are of the newest high-efficiency submersible centrifugal corrosion and wear resistant Alnas
pumps line. There are new stages applied in pump designs allowing to increase unit life-time and to reduce produced oil volume cost
unit at rated delivery with maximum efficiency and minimum power inputs.

0615
Design features 0215 Series 2215 Series Compression
series

No axial shaft bearing in the pump sections. • •

Upper bearing is removed from the section and is built in the

• • •
heads.
Lower bearings are removed from the section and built in the
• • •
base.

Intermediate radial bearings are located along the section

• • •
length in an optimal way

Involute splined shaft • • •

The coupling is removed from the base to the section head • • •

Stages, one-piece all cast metallic impellers • • •

Pump shaft is pre-tensioned and straighten •

Impellers are securely fixed on the shaft •

Protective ribs are removed from the base to the head • • •

Radial bearings have unified design • • •

Original shaft embedding adjustment design • •

Max solids concentration (g/l) 0.5 0.5 1.0
Pump stages are of Ni-resist type cast iron • • •
0215 pump
section

The 0215, 0615, and 2215 series pumps have the following benefits:

• Pump sections without shaft axial bearing provide higher life-time of the pump and the whole installation because of the thrust
bearing, which is arranged in the seal section, is protected from produced water abrasive effect
• Radial bearings build in the heads and in the bases decrease the shaft overhang, increase radial stiffness at the shaft end, and
ensure user declared requirements on runout performance
• Intermediate radial bearing optimal location along the pump sections length allows to increase shaft radial stiffness for lowering
vibration level and enhancing the life-time of the unit. This equipment can be used in high abrasive environments
• Protective ribs are removed from the base to the head allowing to provide cable protection from the very top of the section
• Pump shaft is pre-tensioned (i.e. straighten) leading to lower radial loads on the bearings
• Impellers are securely fixed on the shaft eliminating impeller washers wear
• Adjusting bolt fixed in the shaft end at the head side allow to simplify mounting procedure considerably
• The pump is provided with the intake module of compatible design which allows pump installation with any seal sections made
by Alnas

13
 ABOUT ALNAS
Pumps

ESP PUMP SPECIFICATIONS

Depending on pump transverse overall dimension, there are 4 groups available: 4, 5, 5A, and 6. The group defines production
string minimal inner diameter:

Group 4 5 5А 6
Production string min inner diameter, mm (in.) 112 (4.41) 123.7 (4.87) 130 (5.12) 148.3 (5.84)

Pump body diameter, mm (in.) 86 (3.386) 92 (3.62) 103 (4.06) 114 (4.49)

50 Hz- 2,910 rpm

Pump design Power

Pump capacity in working area Head, min…max
Consumption, min…max

M3/DAY BPD M FT KW HP

ESPCW4-20(I) 12 … 27 75 … 169 100 … 3550 328 … 11648 0.9 … 27.1 1.2 … 37

ESPCW4-40(I) 30 … 50 189 … 314 100 … 3600 328 … 11812 1.1 … 37.2 1.4 … 51

ESPCW4-50(I) 38 … 63 236 … 393 100 … 3600 328 … 11812 1.5 … 43.7 2.0 … 59

ESPCW4-80(I) 60 … 100 377 … 628 100 … 3600 328 … 11812 1.9 … 61.0 2.6 … 83

ESPCW4-100 75 … 130 472 … 817 250 … 3850 820 … 12632 5.8 … 81.0 7.9 … 110

ESP(CW)5-15(I) 10 … 22.5 63 … 141 180 … 3900 591 … 12796 1.1 … 24.7 1.5 … 34

ESPCW5-20(I) 12 … 25 75 … 157 150 … 3750 492 … 12304 1.3 … 28.1 1.8 … 38

ESPCW5-25(I) 18 … 32 113 … 201 150 … 3600 492 … 11812 1.3 … 29.3 1.8 … 40

ESP(CW)5-30(I) 18 … 38 113 … 238 550 … 3550 1805 … 11648 5.4 … 34.8 7.3 … 47

ESPCW5-35(I) 25 … 45 157 … 283 500 … 3600 1641 … 11812 5.7 … 42.2 7.8 … 57

ESP(CW)5-45(I) 35 … 55 220 … 345 500 … 3650 1641 … 11976 6.6 … 45.4 8.9 … 62

ESPCW5-50(I) 30 … 70 189 … 440 500 … 3250 1641 … 10663 7.1 … 46.2 9.7 … 63

ESP(CW)5-50(I)M1 30 … 70 189 … 440 450 … 3600 1476 … 11812 6.3 … 47.3 8.5 … 64

ESP(CW)5-60(I) 40 … 75 252 … 471 150 … 3600 492 … 11812 2.0 … 47.0 2.7 … 64

ESP(CW)5-80(I) 60 … 100 377 … 628 150 … 3550 492 … 11648 2.6 … 56.7 3.5 … 77

ESPCW5-100(I) 80 … 125 503 … 786 150 … 3550 492 … 11648 3.0 … 72.8 4.1 … 99

ESP(CW)5-125(I) 80 … 165 503 … 1037 150 … 3650 492 … 11976 3.5 … 98.1 4.8 … 133

ESPCW5-200M1 130 … 230 818 … 1446 50 … 3500 164 … 11484 3.1 … 140.3 4.2 … 191

ESPCW5-280 210 … 350 1321 … 2201 150 … 2900 492 … 9515 9.9 … 168.3 13.5 … 229

ESPCW5A-35(I) 25 … 50 157 … 314 700 … 3750 2297 … 12304 8.5 … 44.6 11.5 … 61

ESPCW5A-50 25 … 80 157 … 503 600 … 3550 1969 … 11648 8.5 … 51.0 11.5 … 69

ESPCW5A-60 40 … 80 252 … 503 200 … 3550 656 … 11648 2.5 … 49.8 3.5 … 68

ESPCW5A-80(I) 60 … 100 377 … 628 200 … 3600 656 … 11812 3.5 … 66.4 4.8 … 90

ESPCW5A-100(I) 70 … 130 440 … 817 200 … 3650 656 … 11976 4.2 … 78.4 5.8 … 107

ESPCW5A-125(I) 90 … 160 566 … 1006 200 … 3650 656 … 11976 5.2 … 91.7 7.1 … 125

ESP(CW)5A-160M1 120 … 200 755 … 1257 150 … 3650 492 … 11976 4.7 … 112.8 6.3 … 153

ESPCW5A-200M1 125 … 250 786 … 1572 150 … 3600 492 … 11812 5.2 … 131.3 7.0 … 179

ESP(CW)5A-250M1 180 … 300 1132 … 1886 150 … 3600 492 … 11812 7.7 … 187.6 10.4 … 255

ESPCW5A-320 240 … 380 1509 … 2389 250 … 3900 820 … 12796 16.3 … 248.8 22.1 … 338

ESP(CW)5A-400 300 … 500 1887 … 3144 250 … 2800 820 … 9187 18.5 … 208.7 25.2 … 284

ESPCW5A-500M1 375 … 650 2358 … 4087 200 … 2550 656 … 8367 22.8 … 260.6 31.0 … 354

ESP(CW)5A-700M3 640 … 960 4025 … 6037 150 … 2550 492 … 8367 21.8 … 315.5 29.6 … 429

ESP(CW)5A-800M3 640 … 960 4025 … 6037 150 … 2400 492 … 7874 23.2 … 353.3 31.5 … 480

ESPCW6-800M1 600 … 1000 3773 … 6289 200 … 3050 656 … 10007 32.8 … 445.6 44.6 … 606

ESPCW6-1000 850 … 1200 5346 … 7546 150 … 2050 492 … 6726 31.0 … 383.9 42.1 … 522

ESPCW6-1250M1 950 … 1550 5975 … 9747 150 … 1900 492 … 6234 35.5 … 447.6 48.3 … 609
W - the wear resistant type C - the corrosion resistant tupe

14
 ABOUT ALNAS
Pumps

60 Hz-3,492 rpm
Pump make Power
Pump operational range Head, min…max
Consumption, min…max
M3/DAY BPD M FT KW HP

ESPCW4-20(I) 14 … 32 91 … 204 144 … 3900 472 … 12796 1.9 … 51 3 … 69

ESPCW4-40(I) 36 … 60 226 … 377 144 … 3900 472 … 12796 1.8 … 70 2 … 95

ESPCW4-50(I) 45 … 75 283 … 472 144 … 3900 472 … 12796 2.5 … 81 3 … 111

ESPCW4-80(I) 72 … 120 453 … 755 144 … 3900 472 … 12796 3.4 … 113 5 … 154

ESPCW4-100 90 … 156 566 … 981 360 … 3900 1181 … 12796 10.1 … 142 14 … 193

ESP(CW)5-15(I) 12 … 27 75 … 170 259 … 3900 850 … 12796 1.9 … 43 3 … 58

ESPCW5-20(I) 14 … 30 91 … 189 216 … 3900 709 … 12796 2.2 … 51 3 … 69

ESPCW5-25(I) 22 … 38 136 … 241 216 … 3900 709 … 12796 2.3 … 55 3 … 74
ESP(CW)5-30(I) 22 … 46 136 … 287 792 … 3900 2599 … 12796 9.3 … 66 13 … 89
ESPCW5-35(I) 30 … 54 189 … 340 720 … 3900 2362 … 12796 9.9 … 79 13 … 107
ESP(CW)5-45(I) 42 … 66 264 … 415 720 … 3900 2362 … 12796 11.3 … 84 15 … 114
ESPCW5-50(I) 36 … 84 226 … 528 720 … 3900 2362 … 12796 12.3 … 96 17 … 130

ESP(CW)5-50(I)M1 36 … 84 226 … 528 648 ... 3900 2126 … 12796 10.8 … 89 15 … 121

ESP(CW)5-60(I) 48 … 90 302 … 566 216 … 3900 709 … 12796 3.5 … 88 5 … 120

ESP(CW)5-80(I) 72 … 120 453 … 755 216 … 3900 709 … 12796 4.5 … 107 6 … 146

ESPCW5-100(I) 96 … 150 604 … 943 216 … 3900 709 … 12796 5.2 … 137 7 … 186

ESP(CW)5-125(I) 96 … 198 604 … 1245 216 … 2900 709 … 9515 6.1 … 134 8 … 183

ESPCW5-200M1 156 … 276 981 … 1736 72 … 3450 236 … 11319 5.4 … 238 7 … 323

ESPCW5-280 252 … 420 1585 … 2641 216 … 2400 709 … 7874 17.1 … 240 23 … 326

ESPCW5A-35(I) 30 … 60 189 … 377 1008 … 3900 3307 … 12796 14.6 … 80 20 … 109

ESPCW5A-50 30 … 96 189 … 604 864 … 3900 2835 … 12796 14.6 … 97 20 … 132

ESPCW5A-60 48 … 96 302 … 604 288 … 3900 945 … 12796 4.4 … 94 6 … 128

ESPCW5A-80(I) 72 … 120 453 … 755 288 … 3900 945 … 12796 6.1 … 125 8 … 170

ESPCW5A-100(I) 84 … 156 528 … 981 288 … 3600 945 … 11812 7.3 … 133 10 … 181

ESPCW5A-125(I) 108 … 192 679 … 1207 288 … 3900 945 … 12796 9.0 … 168 12 … 228

ESP(CW)5A-160M1 144 … 240 906 … 1509 216 … 3900 709 … 12796 8.1 … 208 11 … 282

ESPCW5A-200M1 150 … 300 943 … 1887 216 … 3600 709 … 11812 9.0 … 228 12 … 310

ESP(CW)5A-250M1 216 … 360 1358 … 2264 216 … 3700 709 … 12140 13.2 … 336 18 … 457

ESPCW5A-320 288 … 456 1811 … 2868 360 … 3000 1181 … 9843 28.1 … 331 38 … 450

ESP(CW)5A-400 360 … 600 2264 … 3773 360 … 2600 1181 … 8531 32.0 … 335 43 … 455

ESPCW5A-500M1 450 … 780 2830 … 4905 288 … 1900 945 … 6234 39.4 … 333 54 … 453

ESP(CW)5A-700M3 768 … 1152 4830 … 7245 216 … 2000 709 … 6562 37.7 … 430 51 … 584

ESP(CW)5A-800M3 768 … 1152 4830 … 7245 216 … 1900 709 … 6234 40.1 … 481 54 … 655

ESPCW6-800M1 720 … 1200 4528 … 7547 288 … 2400 945 … 7874 56.7 … 608 77 … 827

ESPCW6-1000 1020 … 1440 6415 … 9056 216 … 1850 709 … 6070 53.5 … 605 73 … 823

ESPCW6-1250M1 1140 … 1860 7169 … 11698 216 … 1500 709 … 4922 61.4 … 614 83 … 835

15
 ABOUT ALNAS
Gas separators

PPFA SUBMERSIBLE WIRE FILTER

Purpose and Principle of Operation

PPF submersible wire filter is designed to protect ESP from ingress of solids, formation fluid propping
agent particles with cross-section over 0.1 mm (particles content up to 3 g/l). Formation fluid is
filtered when flowing through the filtering element slotted screens. Gravity and vibration effect
results in filter self-cleaning during operation. Filtration degree is defined by the slot size. Bearing
assembly uses bushings of hard alloy. At both sides of movable bush on the shaft, the forced cooling
device for a bearing pair is provided to eliminate overheating of the bearing. PPF submersible wire
filter can be equipped with one or several sections selected depending on pump throughput. PPF
is to be installed between seal section and pump lower section or between seal section and gas
separator (w/o intake module).

Basic benefits:

• Using as ESP unit component

• Repairability
• Filtration degree is 0.1 mm or 0.2 mm
• High strength and durability of the filter
• Clog-proof, self-cleaning filtering elements
• Radial bearing of hard alloy use
• Bearing forced cooling

16
 ABOUT ALNAS
Gas separators

GAS SEPARATORS, DISPENSERS

Gas separators, dispensers, and gas separator-dispensers are designed to ensure electrical
centrifugal pump steady operation when pumping out formation fluid having high gas void
fraction.

Gas separator is essential when oil production well has high dissolved gas content.
For installation at pump inlet instead of intake module or after intake module in a gas
separator model w/o intake screen. Alnas produces and delivers effective gas separators
for all types of pumps and for various operating conditions.

Gas separator operating principle is based on using centrifugal force for free gas disposal.
The gas is withdrawn into annular space to eliminate gas slug generation, ensuring Alnas
ESP unit steady operation and enhancing mean-time-between-failures.

Dispenser is designed for refining entrapped gas in formation fluid, preparation of

homogeneous gas-liquid mixture and feeding it to submersible centrifugal pump inlet.
When gas-liquid mixture flow passes through dispenser, its homogeneity and entrapped
gas breakage degree rise, enhancing centrifugal pump operation: lower vibration and
stream pulsation in tubing, providing operation with efficiency required.

Gas separator-dispensers are installed at pump inlet in lieu of gas separator/ dispenser in
ultrahigh GOR wells, where separator or dispenser application cannot ensure electrical
centrifugal pump steady operation.

APPLICATION CONDITIONS
GSAIS54M1 gas
Gas separators, dispensers, and gas separator-dispensers (the "products") are designed for separator
applications with formation fluid parameters as follows.

Max free gas at inlet (%):

- Gas separators – 55
- Dispensers – 30–40
- Gas separator-dispensers – 75
Delivered liquid temperature (°С) – 150
pH value – 5.0–8.5
Max solids concentration in formation fluid (g/l) – 1.0
Mohs hardness number of particles, max – 7
Max H2S concentration (g/l) – 1.25
Max produced water content (%) – 99
Max density of liquid (kg/m3) – 1,400
Single-phase liquid kinematic viscosity
at which pump operation is provided
without head and efficiency changing (mm2/sec) – 1

DESIGN FEATURES

Radial bearing friction pairs are made of hard alloy. Axial shaft bearing is made of ceramics.
End pieces and protective cases are made of corrosion resistant steel to enhance
hydroabrasive wear resistance. Flow sections are made of corrosion and wear resistant
steel and Ni-resist type iron with hardness of HB 190 to 240. There may be a base design
version with intake shortened openings w/o screen.

All units are supplied in corrosion- and wear-resistant types.

DA5 dispenser

17
 ABOUT ALNAS
Seal sections

SEAL SECTION TYPES:

• All seal section types have single unit design

• Seal section compatibility with the submersible electric motors (clockwise shaft rotation) of other
manufacturers
• Seal section of overall dimension group 5 may be provided with integrated intake module w/ inlet
screen
• Corrosion resistant (C) is available for any seal section type
• Temperature resistant (T1) is available for any seal section type. These seal sections are capable of
operating at formation fluid temperature 150°С max (seal sections w/ rubber goods of operating temp
250°C max are available by special request)
• Using seal section face seal supplied by leading domestic and foreign manufacturers (seal sections w/
rubber goods of operating temp 250°C max are available by special request)
• Provision pressure-relief valves provide bleeding-off surplus intrinsic pressure and free gas phase
removal from the ESM oil chamber during ESP unit operation
• using seal section with elastic diaphragm shroud to provide withdrawing gas and excess oil from motor
inner camera into annular space, allows to exclude vent valves
• Seal section shafts made of high strength stainless steel
• Cooling filter for filtration and cooling oil in thrust bearing assembly area
• Reinforced thrust bearing assembly to sustain pump axial load

MODULAR SEAL SECTION

Modular seal section reference designation is set as follows:

Heat resistance : T – formation fluid temperature 120°С max

T1 – formation fluid temperature 150°С max
Seal section design version (LD, DD, LDD, L2D, LsDD):
LD – seal section contains labyrinth module and diaphragm module; DD – seal section contains 2 diaphragm
modules connected in series (inner diaphragm chambers are sectioned by face seal and valves)
LDD – seal section contains labyrinth and 2 diaphragm modules connected in series (inner diaphragm
chambers are sectioned by face seal and valves)
L2D – seal section contains labyrinth and 2 diaphragm modules connected in parallel (form common inner
chamber)
LsDD – seal section contains shortened labyrinth module and 2 diaphragm modules connected in series
Reference designation for ordering and other product documentation. Example for seal section with formation
fluid temperature max 120°С, overall dimension group 5 modular design, manufactured by Alnas, design
version LD

STMA5LD TU 3381-055-00219454-2011

Reference designation for ordering and other product documentation. Example for seal section corrosion
resistant make with formation fluid temperature max 120°С, overall dimension group 5 modular design,
manufactured by Alnas JSC, design version LDD

SCTMA5LDD TU 3381-055-00219454-2011

Reference designation for ordering and other product documentation. Example for seal section with formation
fluid temperature max 120°С, overall dimension group 6 modular design, manufactured by Alnas JSC, design
version L2D, involute splined shaft connection

GTMA6L2DE TU 3381-055-00219454-2011

Reference designation for ordering and other product documentation. Example for seal section with formation
STMA Seal section
fluid temperature max 150°С, overall dimension group 5A modular design, manufactured by Alnas JSC, design
version LDD, shaft axial bearing reinforced

ST1MA5ALDD BR TU 3381-055-00219454-2011

LD seal section design version is a standard version. Seal sections of design versions LDD and L2D are formed by additional connecting
one diaphragm chamber module to the version LD seal section. The LDD design version seal section have the diaphragm chambers
sectioned by face seal and valves providing additional protection, and the L2D design version seal section diaphragm chambers are
connected directly. The DD design version seal section has no labyrinth module. Type of seal section is selected depending on motor
power and required lube oil volume in the motor.

18
 ABOUT ALNAS
Submersible motors

SUBMERSIBLE MOTORS (ESM)

Submersible oil-filled 3-phase cage rotor, asynchronous, with 2(4)-pole electric motors (“EM”)
are used as a centrifugal pump drives for formation fluid withdrawal from oil wells with operating
borehole deviation angle max 60°. Electric motor complete with seal section is called as a motor
("ESM").

Alnas provides motors of overall dimension groups as follows:

Outside diameter Power

Mm Inch Kw Hp

81 319 50 67
96 378 16…70 21…94
103 406 16…180 21…241
117 460 12…350 16…469
130 512 22…550 29…737
180 709 125…750 167..1005

There are over 100 EM types available with different power ratings, which allows to select the
optimum engine & pump combination providing unit operation with maximum efficiency.
Fabrication technology ensures high quality and reliability of submersible electric motors supplied by
Alnas.

The use of special electrotechnical materials provide submersible motors operation at formation fluid
temperature of up to 200°С for heat-resistant design.

After its assembly on special stands ensuring quality control, the motor is tested at the station in operating conditions similar to
real life, including heating to the operating temperatures. All 100% motors are tested and every motor is to be disassembled and
checked up carefully after its testing. Isolation resistance is controlled by polarization index.

Alnas engineering services have developed and successfully operate new electric motors of M4 and M6 revision with extended
slots of stator coil. Their main feature and obvious benefit, along with those discussed above, is the possibility of operation in
complex geometry wellbores.

Though having the same power as standard motors, modernized M4 and M6 motors length is reduced and, consequently, the
installation of these motors has become significantly easier.

Size 96 motors are especially effective for application in wells after worn casing string repair with transition to a smaller column dia
(112 mm, max) and size 4 pump. The motors are supplied with the STMA4L2D seal section.

New development include size 180 motors used as submersible centrifugal pump drives for formation fluid withdrawal from oil
wells at temperatures of up to 200°С, and the motors used for injection liquid for formation pressure maintenance in oil wells with
operating borehole deviation angle of up to 40°.

As per user requirements, motors can be completed with shafts and clutches with involute profile, centralizers screwed into the
motor base and preventing motor body contact with casing pipe, jacks for sectional electric motor smooth installing

MOTOR LEAD EXTENSION (MLE) AND CABLE LINES

Alnas manufactures a wide range of MLE and cable lines, AWG # 1 to 7.

Temperature rating is up to 250°C (482F)

Alnas produces cable and MLE using the best components and materials of Russian
and foreign manufacturers.

19
 ABOUT ALNAS
INM-3 control stations

SURFACE EQUIPMENT
NEW GENERATION OF INM-3 VSD CONTROL STATIONS

INM-3 control stations with a power ratio of up to 525 kVA are designed
for remote, manual and automatic control and protection of pumping units
fitted with asynchronous motors.

The benefits of these control stations are simple – intuitive UI, wide
range of model versions, high reliability, versatile control algorithms, and
intellectual well control algorithms.

User Benefits:

• Operational costs lower due to early failure detection and preventive

actions to eliminate possible damage.
• Power supply costs lower due to ESM power consumption optimiza-
tion function provided.
• Control station & oilfield equipment maintenance costs reduction.
• Oilfield equipment downtime reduction.
• Effective oil reservoir operation due to operational monitoring and
oilfield equipment operation mode control.
• Reduced costs for additional telemetric equipment.

Control Station Operation Basic Concepts

The station operation is convenient for user to the maximum extent.

Optional configuration to meet user’s requirements at procurement stage
and/or easy functional upgrade at operating stage.

CONTROL STATION BENEFITS

Wide range of choices – Control station modular design permits various motor control system applications providing multiple
features:
• Direct-on-line starting with motor soft start ability
• Variable speed drive control stations for asynchronous electric motors
• Submerged and wellhead telemetry systems

Smart control functions – Control station executes calculation of "layer – well – pump unit" system basic indexes, such as well
production rate and dynamic level, and provides diagnostics and optimization of pump system when a variable speed drive is used.

Easy information read-out – Remote connection and information read-out using RS-485 interface or station operating log archive
read-out using USB Flash.

Easy management – large graphic display, informative interface, and advanced station controller menu provide easy access to any
information or station configuration.

Easy station status monitoring – External LED indication allows any personnel to easily monitor station status.

Easy maintenance – Modular design provides for possibility of maintenance at the operation site.

TMS support – Control station allows operation with the submerged telemetry system of various brands.

Telemechanics protocol support – Control stations have a feature of connecting to telemechanics systems, such as Region 2000 and
Telescope +.

Easy modernization – Control stations have a feature of modernization and functional parameter expansion via station controller
programming in the field without uninstalling the controller.

20
 ABOUT ALNAS
INM-3 control stations

BASIC TECHNICAL DATA

Rated voltage at 50 Hz (V); voltage tolerance (%) 380; –30...+25

Nominal current, A 250; 400; 630; 800

Output voltage frequency, Hz 0-200

Connected ESM types Converter-fed asynchronous

Output voltage PDM, 2.4-4.5 kHz, U/F characteristic, 20 points

ESM speed adjusting range, rpm 0…6,000

TMS submersion telemetry
Extra modules USB Flash
INM-3 read-out device
RS-232, 2 × RS-485
Communication interfaces
USB, CAN
Temperature range, °С -60…+50

Overall dimensions, mm 1,950 × 800 × 650

Weight, kg 450…650

BASIC FEATURES AND BENEFITS

The frequency converter allows to run additionally the followings modes and service functions:

• Motor soft start and braking

• Change pump unit rotation direction
• Pump unit shimming mode
• "Shaking" mode
• ESM shaft maximum torque limit mode
• U/F performance characteristic automatic generation mode
• Voltage stabilization mode
• ESM max efficiency support mode
• Well parameters calculation
• Pressure buildup curve measuring
• Keeping suction pressure.

OUTPUT SINE FILTER

At the customer 's request, control station with frequency control can be completed with output sine filters:

• VSD-250 – Built-in filter, removable, modular design

• VSD-400 – Separate box filter, connected between CS and oil transformer, INM-3-400 type filter
• VSD-630 – Separate box filter, connected between CS and oil transformer, INM-3-630 type filter.
• VSD-800 - Separate box filter, connected between CS and oil transformer, INM-3-800 type filter.

21
 ABOUT ALNAS
Units for reservoir maintenance systems

UNITS FOR RESERVOIR PRESSURE MAINTENANCE SYSTEMS

Centrifugal pump assemblies are designed for fresh water, formation water, and produced water injection to maintain reservoir pressure.

The units are manufactured on standard Alnas ESP unit base, providing for the following:
• Manufacturing time-frame is reduced
• All basic components are debugged
• All design decisions applied, thus considerably enhancing equipment reliability and endurance
• Assembly/disassembly is simplified
• Maintenance and repair is simplified.

THE ESP-H HORIZONTAL PUMP UNIT FOR WATER INJECTION

The unit is designed as a surface-type device, which facilitates its maintenance and repair and allows for use of ordinary asynchronous
motors.

One unit allows multiple-well application.

The ESP-HH units have a 45 to 1,250 m³/day capacity at a maximum head of 200 atm. Supplied with ESP-HH pumps of overall dimension
groups 5, 5A and 6.

Over 40 Alnas horizontal ESP units are successfully operated by PJSC TATNEFT.

Asynchronous motor Coupling P IN

Inlet of pump Outlet pipe
sleeve section

P OUT
Frame

22
 ABOUT ALNAS
Units for reservoir maintenance systems

ESP-V VERTICAL PUMP UNIT FOR WATER INJECTION

Several types of the centrifugal units for water injection are available.

The ESP-V pump unit for water injection is an individual submersible unit permitting
selective injection into selected wells.

The ESP-V series pump units for water injection have a number of advantages, as
compared with similar equipment:

• Long service life

• Easy operation – The unit is underground and does not require special apartment for
its mount
• Нead and capacity characteristics for a particular well are selected optionally
• High repairability

The unit design has an inverted scheme by comparison with traditional ESP units. Liquid
flow is directed from top to base providing water injection in a layer. Injection part is
packed to isolate it from liquid supply part. A liquid is supplied from the column top.
In conditions of well remote location from basic communications and other reservoir
pressure maintenance systems, these units application is optimum. The units for injecting
water from layer to layer can be equipped with a downhole flow meter to measure pump
discharge rate and pressure.

Supplied with ESP-H pumps of overall dimension groups 5 and 5A.

ESPCWCW PUMP UNIT FOR CENOMANIAN WATER

ESPCWCW pump unit for Cenomanian water is designed to produce and subsequently
inject into the formation highly mineralized aggressive Cenomanian deep waters. Pump
operating elements are of corrosion-resistant Ni-resist alloy. The unit allows to pump over
water with total dissolved solids of 15.9...20.3 g/l and density of 1400 kg/m3. This pump
type benefits are ability of operating at pumped water temperature 90°С and corrosion
resistance. The units have the same design as ESP units made by Alnas. All units can be
used both for several wells or for a separate well, which eliminates the need of laying long
high-pressure mains and requires minimum capital investment in protective buildings. A
complete set can include a smooth start control station, increasing the service life and
reducing starting torques during unit operation.

MOUNTING & INSTALLATION TOOLS AND SPARES

ESP-V unit
Alnas offers a complete tool set necessary for on-site installation works.
Mounting & installation tools
• Special wrenches
• Torque wrenches
• Heavy-duty wrenches
• Megohmmeter
• Other necessary instruments are supplied in ultra portable case.

Accessories include:
• Charging pump
• Pressurizing cap
• Pedestal, elevator clamp, suspender

At the user's request, the tools can be supplied in any assortment and quantities both for existing and for newly equipped fields.
For submersible unit post-guarantee repair, all necessary spare parts (components) can be supplied in any assortment and quantities.

23
 ABOUT
IZHNEFTEMASH
Izhneftemash is one of the leading Russian enterprises of oil engineering. The plant enters into RIMERA Group from 2008.

Having more than fifty years of history, valuable unique experience and skilled staff in oilfield equipment production, the plant has
proven itself as a reliable business partner not only in Russia, but far abroad.

Izhneftemash is a modern company with effective management system. High quality and reliability of equipment, client-focus ap-
proach and a wide range of product lines provide the plant stable development.

TODAY THE PLANT PRODUCES:

About 50% of automatic stationary break out tongs produced in Russia;

Over 40% of sucker rod pumps and pumping units for bottomhole oil production. Sucker rod pumps are produced according to API
Specification 11AX, and pumping units are produced according to API Specification 11E in accordance with the license agreement
providing the right to put API monogram on the equipment produced;

30% of pump units and 45% of mixing units for cementing of oil and gas wells during drilling and overhaul.

Izhneftemash applies integrated approach to the work with customers. Along with equipment production, the plant supplies spare
parts, carries out overhaul of equipment (sucker rod pumps, break out tongs, gear reducers, mud pumps and cementing pumps) at main
production facilities according to its technology. The plant also fulfills special orders and manufactures equipment under individual
requirements of customers.

24
 ABOUT IZHNEFTEMASH

QUALITY

The quality management system being in effect at the plant meets the requirements of the
international standards, ISO-9001 and API Q1 and is certified by the American Petroleum
Institute Quality Registrar. Manufactured goods meet all requirements of GOST R standards
and industrial safety rules.

In addition, Izhneftemash has a certificate of conformity No. DSAT RU.OC015.TO0506

providing the right to perform maintenance and repair of transport facilities, machines and
equipment.

It allows the enterprise to carry out re-equipment of transport facilities.

SERVICE

Izhneftemash’ specialists ensure execution of warranty obligations, collection of information

on operation of oil equipment and suggestions to increase technical and operational charac-
teristics.

Except for this catalog, including all types of produced equipment, catalogs of assembly units
and parts are available. These catalogs cover denomination, designation, configuration of
assembly units and parts, their relative positions in a machine, makes of parts. Specialists, who
carry out service maintenance, repair of equipment and ordering of spare parts, can receive
the catalogs of assembly units by request.

By agreement with customer, the plant can supply equipment of special designs taking into
consideration special customer requirements.

25
 ABOUT IZHNEFTEMASH
Oil production equipment

Oil Production Equipment

BEAM PUMPING UNITS
WITH DOUBLE-ARMED WALKING BEAM PNSH, PNSHT

These types of pumping units are used as an individual mechanical drive for sucker rod pumps in oil production.

Pumping units PNSh 60 and PNSh 80 are developed on the base of SK-6 and SKD-8 respectively. Their main units and components
are interchangeable.

Pumping units are equipped with double-stage gear reducers.

Pumping units PNShT (pedestal version) are equipped with double- and three-stage gear reducers and engines differed by horse-
power and rotation frequency. It allows choosing design of a pumping unit ensuring the best oil production conditions with minimum
power consumption.

26
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSH 60-2.1-25
(Similar by technical characteristics to C-80D-119-54, C-80D-133-54, C-80D-119-64)
for mounting on a low foundation

Parameters Value

Maximum rod load, kN (lbf) 60 (13.400)

Stroke length, m (in) 2.1 / 1.8 / 1.5 / 1.2 / 0.9 (82.6/70.8/59/47/35.5)
Gear reducer RP 450-28
Pulley diameters, mm (in):
- Gear reducer 710 (27.9)
- Engine 200; 250; 315 (7.8; 9.8; 12.4)
Brake Drum-type
Overall dimensions, mm (in) 7.060 × 1.880 × 6.480 (278 × 74 × 255)
- length 8.060 (317)
- width 1.880 (74)
- height 5.450 (215)
Weight, kg (lbs) 9.140 (20.150)

Engine
Designation of pumping unit Swings per minute Gear reducer
Power, kW rpm
PNSh 60-2.1-25 5.3; 6.6; 8.3 18.5 750

PNSh 60-2.1-25-01 3.5; 4.4; 5.5 15.0 500

RP450
PNSh 60-2.1-25-01.01 3.5; 4.4; 5.5 11.0 500

PNSh 60-2.1-25-02 7.0; 8.7; 11.0 18.5 1000

27
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSHT 60-3-31.5

(Similar by technical characteristics to C-80D-119-54, C-80D-133-54, C-80D-119-64)

for mounting on a low foundation

Parameters Value

Maximum rod load, kN (lbf) 60 (13,400)

Stroke length, m (in) 3.0/2.5/2.0/1.6/1.2 (118/98.5/78.7/63/47)

RT28, three-stage, gear ratios 125, RP 450-28
Gear reducer
90, 63 double-stage
Pulley diameters, mm (in):
- Gear reducer 900 (35.4)
- Engine 200; 250; 280 (7.8; 9.8; 11)
Brake Drum-type

Overall dimensions, mm (in) 7.060 × 1.880 × 6.480 (278 × 74 × 255)

Weight, kg (lbs) 8.920 (19.648)

Range of beam Engine

Designation Gear reducer
swings per min. N, kw N, rpm
PNShT 60-3-31.5-125 1.3...1.8 5.5 750
PNShT 60-3-31.5-125-01 1.7...2.4 RT28-125 7.5 1.000
PNShT 60-3-31.5-125-02 2.6...3.6 11 1.500
PNShT 60-3-31.5-90 1.8..2.5 7.5 750
PNShT 60-3-31.5-90-01 2.4...3.4 11 1.000
PNShT 60-3-31.5-90-02 3.6...5.0 RT28-90 15 1.500
PNShT 60-3-31.5-90-03 1.2…1.7 15 500
PNShT 60-3-31.5-90-04 1.2…1.7 11 500
PNShT 60-3-31.5-63 2.6..3.6 11 750
PNShT 60-3-31.5-63-01 3.4...4.8 RT28-63 15 1.000
PNShT 60-3-31.5-63-02 5.1...7.2 18.5 1.500
PNShT 60-3-31.5-40 4.1…5.7 15 750
PNShT 60-3-31.5-40-01 5.4…7.5 RP 450-28 18.5 1.000
PNShT 60-3-31.5-40-02 8.1…11.3 22 1.500

28
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSH 80-3-40

(Similar by technical characteristics to C-114D-173-64, C-160D-173-74, C-228D-173-74)

for mounting on a high foundation

Parameters Value

Maximum rod load, kN (lbf) 80 (17,985)

Stroke length, m (in) 3.0/2.5/2.0/1.6/1.2 (118/98.5/78.7/63/47)

Gear reducer RP 450, double-stage, gear ratio 37

Pulley diameters, mm (in):
- Gear reducer 900 (35.4)
- Engine 200; 250; 280 (7.8; 9.8; 11)
Brake Drum-type

Overall dimensions, mm (in) 7,100 × 2,250 × 5,385 (279 × 68.5 × 212)

Weight, kg (lbs) 12,400 (27,312)

Engine
Designation Range of swings per minute Gear reducer
Power, kW rpm
PNSh 80-3-40 4.3...6.2 18.5 750

PNSh 80-3-40-01 5.8…8.1 22 1.000

RP450
PNSh 80-3-40-02 8.6…12.0 30 1.500

PNSh 80-3-40-03 3.0…4.2 15 500

29
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSHT 80-3-40

(Similar by technical characteristics to C-114D-173-64, C-160D-173-74, C-228D-173-74)

for mounting on a low foundation

Parameters Value

Maximum rod load, kN (lbf) 80 (17,985)

Stroke length, m (in) 3.0/2.5/2.0/1.6/1.2 (118/98.5/78.7/63/47)

Gear reducer Double - or three-stage

Pulley diameters, mm (in):
- gear reducer 900 (35.4)
- engine 200, 250; 280 (7.8; 9.8; 11)
Brake Drum-type

Overall dimensions, mm (in) 7.100 × 2.300 × 6.750 (279 × 90.5 × 265)

Weight, kg (lbs) 13.010 (28.682)

Engine
Designation Range of swings per minute Gear reducer
Power, kW rpm
PNShT 80-3-40-125 1.3...1.8 7.5 750

PNShT 80-3-40-125-01 1.7...2.4 RT40-125 11 1.000

PNShT 80-3-40-125-02 2.5...3.6 15 1.500

PNShT 80-3-40-90 1.9...2.6 11 750

PNShT 80-3-40-90-01 2.5...3.5 15 1000

RT40-90
PNShT 80-3-40-90-02 3.7...5.2 18.5 1.500

PNShT 80-3-40-90-03 1.2…1.7 15 500

PNShT 80-3-40-63 2.6...3.7 15 750

PNShT 80-3-40-63-01 3.5...4.9 RT40-63 18.5 1.000

PNShT 80-3-40-63-02 5.3...7.4 22 1.500

PNShT 80-3-40-37 4.3..6.0 18.5 750

PNShT 80-3-40-37-01 5.8...8.1 RP 450 22 1.000

PNShT 80-3-40-37-02 8.5...12 30 1.500

30
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSH 80-3.5

(Similar by technical characteristics to C-114D-173-64, C-160D-173-74, C-228D-173-74)

for mounting on a high foundation

Parameters Value

Maximum rod load, kN (lbf) 80 (17,985)

Stroke length, m (in) 3.5/3.0/2.5/2.0/1.5 (37.8/118/98.5/78.7/59)

Gear reducer RP 450, double-stage, gear ratio 37

Pulley diameters, mm (in):
- gear reducer 1250 (49.2)
- engine 200, 250; 315; 380 (7.8; 9.8; 12.4; 15)
Brake Drum-type

Overall dimensions, mm (in) 7.100 × 2.250 × 5.385 (279 × 88.5 × 212)

Weight, kg (lbs) 12.400 (27.312)

Engine
Designation Swings per minute Gear reducer
Power, kW rpm
PNSh 80-3.5-40 3.1; 3.9; 4.9; 6.0 30.0 750
RP450
PNSh 80-3.5-40-01 3.1; 3.9; 4.9; 6.0 37.0 750

31
 ABOUT IZHNEFTEMASH
Oil production equipment

PNSHT 70-1.9-31.5

(Similar by technical characteristics to C-160D-143-74)

PNShT 70-1.9-31.5 Pumping unit has an extended range of polished rod stroke length. In order to provide safer unit operation, it is
equipped with a special safeguard of 2 meters high, restricting access to both the pumping unit and a wellhead. Electric motor is pro-
tected by additional shroud. Besides, gear reducer hatch cover and drain plug are protected from unauthorized opening and oil drain.

Parameters Value

Max load on polished rod, kN (lbf) 70 (15,736)

Stroke length, in (m) 74 (1.9); 64 (1.6); 48 (1.2); 36 (0.9); 20 (0.5); 12 (0.3)
Gear reducer RP 450-28 double-stage
- transmission Poly-V-belt
- torque, kN·m 40
Pulley diameter, mm (in):
- gear reducer 900 (35.4)
- engine 200; 250; 280; 315 (7.8; 9.8; 11; 12.4)
Brake Drum-type
Transmission Poly-V-belt
Overall dimensions
(at horizontal position of walking beam), mm (in):
- length 6.450 (254)
- width (without safeguard) 2.050 (81)
- height 5.425 (214)
Weight, kg (lbs) 10.000 (22.050)

32
 ABOUT IZHNEFTEMASH
Oil production equipment

PUMPING UNIT C-320-256-120

(Similar to Lufkin pumping unit)

Parameters Value

Max load on polished rod, kN (lbf) 114 (25,627)

Stroke length, in (m) 3.05 (120); 2.6 (102); 2.08 (82)

Gear reducer Double-stage 320D

Rated gear reducer gear ratio 28.8

Brake Drum-type

Pulley diameters, mm (in):

- gear reducer 1,120 (44)

- engine 200 (7 ¾); 250 (9 ¾); 280 (11)

Overall dimensions (without safeguard), mm (in):

- length 10.160 (400)

- width 3.505 (138)

- height 7.823 (308)
Weight, kg (lbs) 23.000 (51.340)

33
 ABOUT IZHNEFTEMASH
Oil production equipment

MOBILE PUMPING UNIT WITH ELECTRIC DRIVE PNSHME ( 91-2.5-40/116-2.5-40)

Mobile Pumping Unit is intended for test short-term service of reactivated or new wells to determine their productivity and other
characteristics that help to choose a size and make of a stationary pumping unit for well operation.

If required, Mobile Pumping Unit may be used for continued well operation.

Transport position Working position

Mobile Pumping Unit produced by Izhneftemash has several advantages over foreign analogues:

• Hinge-jointed unit consisting of a walking beam, a Samson post and a frame is very easy in design, that’s why Mobile Pumping Unit
may be quickly transformed from transport to working position and conversely with any crane truck
• A commercial semi-trailer and a beam-balanced pumping unit involving unified components are included in Mobile Pumping Unit.
This significantly reduces the cost of a unit, increases its reliability and serviceability
• Automatic descending and lifting of base plates when transforming Mobile Pumping Unit from transport to working position and
conversely with a general-purpose crane truck having a load capacity of 10 tons and more

Parameters Value

Size PNShME 91-2.5-40 PNShME 116-2.5-40

Max load on polished rod, kN (t) 91 (9.1) 116 (11.6)

Stroke length, m 2.5 / 2.0 / 1.8 / 1.4 / 1.2

Gear reducer Double-stage. RP450 (Ts2NSh-750B)

Torque on gear reducer driven shaft, kN·m 40

Gear reducer gear ratio 37

Type of the belt Single. five- track
Number, pcs. 1
gear reducer 1250
V-belt transmission
Pulley diameters, 200
mm 250
engine
315
380
3.1
3.9
Swings per minute
4.9
6.0
Revolutions per minute of engine, rpm 750

Rated engine power, kW 30

Overall dimensions without truck, mm, max:

- width 2500

in working position 12 500

- length
in transport position 11 530

in working position 6.450

- height
in transport position 3.960

Weight of pumping unit, kg 13 200

Weight of pumping unit with a semitrailer, kg, max 21 600

Max speed on highway, km/h 60

34
 ABOUT IZHNEFTEMASH
Oil production equipment

Gear Reducers for PNSh, PNShT,

OPNSh, PC Pumping Units
DOUBLE-STAGE GEAR REDUCERS RP TYPE

High-speed and low-speed stages are herringbone gear with thermally improved Novikov gearing.

Parameters RP 450-28 RP 450

Maximum gear reducer output torque, kN·m (lbf х in) 28 (247.790) 40 (353.980)
Rated gear ratio 40 37

Lubrication volume in crankcase, dmз 90 110

Overall dimensions, mm (in)

- length 1.450 (57) 1.483 (58)
- width 1.542 (61) 1.930 (76)
- height 958 (38) 968 (38)
Weight, kg (lbs) 2.105 (4636) 2.720 (6189)

THREE-STAGE GEAR REDUCERS RT TYPE

Equipped with herringbone gear with thermally improved Novikov gearing.

Parameters RT 28 RT 40

Maximum gear reducer output torque, kN·m (lbf х in) 28 (247.790) 40 (353.980)
Rated gear ratio 63; 90; 125 63; 90; 125
Lubrication volume in crankcase, dmз 110 150
Overall dimensions, mm (in)
- length 1.450 (57) 1.520 (59)
- width 1.542 (61) 1.915 (75)
- height 958 (38) 970 (39)
Weight, kg (lbs) 2.210 (4867) 2.810 (6189)

35
 ABOUT IZHNEFTEMASH
Oil production equipment

Sucker Rod Pumps

By their design, the pumps meet main requirements (except tubing thread) of API Specification 11AX.
They consist of one-piece heavy wall barrel with two extensions, one plunger, traveling and standing
valves and anchor.

There are more than 1,000 pump types and makes produced, both standard (as per API Specification
11AX) and special makes, including pumps for operation in extra-heavy well conditions.

Prizewinner of the Russian Prizewinner of the

Trademark national contest ”100 Best Russian Products”
contest program

TYPES OF PRODUCED PUMPS

Pump marking
Combination of tubing dia.
Pump type Mechanical seating Cup seating
and pump dia.
arrangement arrangement

With top anchor RНАМ RHAC 20-106(25-106)

20-125(25-125)
Rod Pumps with standing barrel 25-150
With bottom anchor RHBM RHBC 25-175
30-225

Rod pumps with traveling barrel With bottom anchor RHTM - 25-175
Two-stage rod pumps With bottom anchor RHBM - 30-225/150
25-106
20-125 (25-125)
ТНМ
25-150
Tubing pumps (ТНМ-Т, ТНМ-С, ТНС
20-175 (25-175)
ТНМ-К)
25-225
30-275

36
 ABOUT IZHNEFTEMASH
Oil production equipment

STRUCTURE OF FULL PUMP DESTINATION BY API:

All the manufactured pumps are modified for Russian downhole equipment for installing in straight tubing string
(with non-upset ends) as per GOST 633-80 and connecting with sucker rod string as per GOST 13877-96.

For connecting filters or other safety devices to bottom of a pump – LP internal thread (pipeline thread) – 1:16 taper;
11.5 threads per inch. Thread diameter: 1", 1 1/4", 1 1/2", 2" (depending on pump type and diameter).

MAKES OF PUMP COMPONENTS:

BARREL:

• Alloy steel, nitride-plated (HN)

• Carbon steel, chrome-plated (CR);
Length of nitride-plated barrels – up to 14 feet, chrome-plated – up to 16 feet, compound barrels (for long-stroke
pumps) – up to 28 feet.

PLUNGER (NIPPLE TYPE):

• Carbon steel, chromium-nickel hard alloy powder sprayed (T)

• Grooved, smooth
• Length – up to 5 feet, compound – up to 10 feet.

VALVES:

Standard and special designs, including double traveling and standing valves.

Double Valve
VALVE CAGE:

• Alloy steel
• Stainless steel.

BALL AND SEAT:

• Stainless steel (SS)

• Cobalt alloy (ST)
• Tungsten carbide (TC1)

Plunger clearance is defined as a difference between nominal diameters of a plunger and a barrel plus sum of toler-
ances for plunger and barrel diameters.

PLUNGER CLEARANCE (RANGE):

• Fit-1 — 0.025 … 0.088 mm (0.001 in)

• Fit-2 — 0.050 … 0.113 mm (0.002 in)
• Fit-3 — 0.075 … 0.138 mm (0.003 in)
• Fit-4 — 0.100 … 0.163 mm (0.004 in)

37
 ABOUT IZHNEFTEMASH
Oil production equipment

When making a request/order for pumps, Customer should specify:

• Denomination, full designation of a pump including tubing diameter; diameter and type of a pump; length of a barrel, plunger
and extensions (or required plunger stroke)
• Type of top seating arrangement of rod pumps: standard (according to API), in OM anchor (according to Industry standard
OST) or special «taper-in-taper» type
• Type of seating arrangement of standing valve of tubing pumps: standard (according to API), non-removable

Plunger clearance (Fit 1,2,3,...)

Depth of pump installation (discharge)

Material of barrel, plunger, valves, valve cages

Additional requirements to pump makes

If no requirements to material, clearance and discharge of pumps are specified, then the following types and makes of pumps are
delivered: barrel HN, plunger T, valves SS, alloy steel valve cages, Fit2, discharge up to 1,500 m.

Seating nipples (anchors) of rod pumps, as well as filters, overflow valves, automatic tractive connections, and other tools for SRP
are not included in a delivery set and should be ordered optionally.

38
 ABOUT IZHNEFTEMASH
Oil production equipment

ROD (INSERT ) PUMPS Scheme of top (mechanical) anchored

rod pump acc. to API
Rod (insert) pumps are delivered with sand wiper (sand valve). It is installed in
Rod guide
rod guide to prevent sanding up of a pump during its idle time.

To provide better sealing of pump anchoring unit in corrosion environment, an Sand wiper
anchor spindle of top mechanical seating arrangement, as per API, assembled Packing nut
with stainless steel packing nut is available.
Seating assembly

Barrel

Extension coupling
(2 pcs.)

Standing valve

Rod subcoupling

Rod

Plunger

Traveling valve

Scheme of seating arrangement

Sand wiper

Anchor spindle
Sealing ring

Lock sleeve
Seating nipple

Pump RHAM

39
 ABOUT IZHNEFTEMASH
Oil production equipment

MAKES OF ROD PUMPS:

Seating Pump bore, Pump bore, Tubing size, Tubing size, Designation of seating
Pump designation*
arrangement mm in mm in nipple (anchor)
60.3 2 3/8 40116-ZUS
27.0 1 1/16 20-106 RHAM
73.0 2 7/8 40116-M-ZUS

Top mechanical 60.3 2 3/8 40116-ZUS

acc. to API 31.8 1 1/4 20-125 RHAM
73.0 2 7/8 40116-M-ZUS
38.1 1 1/2 25-150 RHAM
73.0 2 7/8 40117-ZUS
44.5 1 3/4 25-175 RHAM
27.0 1 1/16 20-106 RHAM
Top mechanical in 60.3 2 3/8 OM-60
OM support, acc. 31.8 1 1/4 20-125 RHAM
to OST 26.16.06- 38.1 1 1/2 25-150 RHAM
86 73.0 2 3/8 OM-73
44.5 1 3/4 25-175 RHAM
27.0 1 1/16 25-106 RHAM
32001-M, 32001-КM,
31.8 1 1/4 25-125 RHAM 40116-KM-ZUS
Top special
73.0 2 7/8
(taper-in-taper)
38.1 1 1/2 25-150 RHAM
32002-M, 32002-КM,
44.5 1 3/4 25-175 RHAM 40117-KM-ZUS

60.3 2 3/8 20-106 RHAC 32521

27.0 1 1/16
73.0 2 7/8 25-106 RHAC 32522
60.3 2 3/8 20-125 RHAC 32521
Top cup acc. to API 31.8 1 1/4
25-125 RHAC
38.1 1 1/2 73.0 2 7/8 25-150 RHAC 32522
44.5 1 3/4 25-175 RHAC
60.3 2 3/8 20-106 RHBM 32756
27.0 1 1/16
73.0 2 7/8 25-106 RHBM 32757
60.3 2 3/8 20-125 RHBM 32756
Bottom mechani- 31.8 1 1/4
73.0 2 7/8 25-125 RHBM
cal acc. to API
38.1 1 1/2 25-150 RHBM 32757
73.0 2 7/8
44,5 1 3/4 25-175 RHBM
57.2 2 1/4 88.9 3 1/2 30-225 RHBM 32758

Bottom mechani-
2 1/4 30-225/150 RHBM
cal, double-stage 57.2/38.1 88.9 3 1/2 32758
1 1/2 12-4-2-2
pump

27.0 1 1/16 20-106 RHBC

60.3 2 3/8 32521
20-125 RHBC
Bottom cup acc. 31.8 1 1/4
25-125 RHBC
to API
38.1 1 1/2 73.0 2 7/8 25-150 RHBC 32522
44.5 1 3/4 25-175 RHBC

27.0 1 1/16 25/20-106 RHM-T

Bottom mechani- 31.8 1 1/4 25/20-125 RHM-T

2 7/8
cal acc. to API, set 38.1 1 1/2 73.0/ 60.3 25/20-150 RHM-T 40116-MT-ZUS
2 3/8
in pump bottom
44.5 1 3/4 25/20-175 RHM-T

Travelling barrel,
bottom mechanical 44.5 1 3/4 73.0 2 7/8 25-175RHTM OM-73
acc. to OST

*Pump designation is given without lengths of a barrel, a plunger and extensions, which are selected for each pump type and make according to required
plunger stroke.

40
 ABOUT IZHNEFTEMASH
Oil production equipment

ANCHOR ( SEATING NIPPLE ) OF ROD (INSERT ) PUMPS

Top (bottom) cup Bottom mechanical

seating arrange- seating arrangement
ment acc. to API acc. to API

Anchor
mandrel

Seating
nipple

Seating arrangement Designation Connecting thread, mm Connecting thread, in

40116-ZUS 60 2 3/8
Acc. to API 40116-М- ZUS 40117- ZUS 73 2 7/8
40116-MT-ZUS 73/60 2 7/8 2 3/8
Top mechanical 32001-М, 40-116-KM-ZUS 73 2 7/8
Taper-in-taper
32002-М, 40117-KM-ZUS 73 2 7/8
ОМ-60 60 2 3/8
Acc. to OST
ОМ-73 73 2 7/8
32521 60 2 3/8
Top and bottom cup Acc. to API
32522 73 2 7/8

32756 60 2 3/8

Bottom mechanical Acc. to API 32757 73 2 7/8

32758 89 3 1/2

41
 ABOUT IZHNEFTEMASH
Oil production equipment

ROD (INSERT ) PUMPS OF SPECIAL DESIGN:

Pump, RHM-T
Makes: (plunger is not shown)
• RHAM pumps with anchor at the top end of a pump for setting in OM support according to
ОSТ 26.16.06-86

• RHAM pumps with anchor at the top end of a pump for setting in seating nipple of «ta-
per-in-taper» seating arrangement

• RHM-T pumps with diameters 27, 32, 38 and 44 mm, at the bottom end of which top
mechanical seating assembly acc. to API from pumps with diameter from 27 mm to 32 mm.
Pumps are installed in 40116-MT-ZUS seating nipple with connecting thread of tubing 73
mm on the top and tubing 60 mm on the bottom. Such design of pumps allows to install
RHAM pumps with diameters 27 mm and 32 mm and RHM-T pumps of all diameters
(25/20-106 RHM-T, 25/20-125 RHM-T, 25/20-150 RHM-T, 25/20-175 RHM-T) in a well with
40116-MT-ZUS seating nipple

• Double-stage pumps

• At the customer’s request, standard pumps can be equipped with doubled standing and
traveling valves

Example of rod pump designation

Diameter 32 mm with bottom mechanical seating arrangement acc. to API, length of barrel – 12
feet, length of plunger – 4 feet, extensions – 2 feet each, for installation in tubing 73 mm:
25-125 RHBM 12-4-2-2

Top mechanical seating arrangement Top mechanical seating arrangement

in OM support “taper-in-taper” (integral seating
nipple is delivered as well)

Seating nipple
40116-MT-ZUS
Composite seating nipple

OM support

Top mechanical
Sealing ring seating
arrangement acc.
to API

Anchor spindle

42
 ABOUT IZHNEFTEMASH
Oil production equipment

DOUBLE-STAGE (DIFFERENTIAL) PUMP 30-225/150 RHBM 12-4-2-2

Consists of: Operation scheme of

a double-stage pump
• Barrel with standing valve. There is a hollow rod guide on the top of barrel for
sealing upper chamber (high-pressure stage)

• Plunger with traveling valve and hollow polished rod with additional valve on
the top of a rod. Rod is connected with plunger with the help of adapter with
side holes connecting internal hollow of a plunger and a rod with upper cham- Additional valve
ber which is the space between rod and barrel
Hollow rod sealing
• Inner hollows of a plunger with traveling valve, rod with valve and upper cham-
ber create high pressure stage. Under-plunger space (lower chamber) is a low
pressure stage.
Hollow polished
rod

Pump operation:
Barrel
When plunger moves upwards, both plunger valves are closed; standing valve is
opened, and well fluid flows in a lower chamber (low pressure stage)

When plunger moves downwards, upper plunger valve remains closed and standing
valve is closing. Fluid flows in upper chamber through open lower plunger valve Plunger

With following upstroke, lower plunger valve is closed by fluid pressure, which is
achieved by diminishing upper chamber space
Traveling
When pressure in upper chamber equals the fluid column pressure in tubing string, valve
upper plunger valve opens and fluid flows in tubing string. At the same time, fluid
flows through opened standing valve into lower chamber

Thus, lower chamber is filled and released without fluid column pressure in tubing. It
creates favorable conditions for pumping gassed well fluid. Standing valve

ROD PUMP PLUNGER STROKE BASED ON THE COMBINATION OF THE LENGTHS OF

THE BARREL – PLUNGER – EXTENSIONS

Barrel - plunger - extension - extension Maximum plunger stroke (stop-to-stop), m

7-4-1,5-1,5 1.4
9-4-1,5-1,5 2.0
10-4-1,5-1,5 2.3
12-4-1,5-1,5 2.9
12-4-2-2 3.2
14-4-1,5-1,5 3.5
14-4-2-2 3.8
14-5-1,5-1,5 3.2
22-4-2-2 6.2

43
 ABOUT IZHNEFTEMASH
Oil production equipment

TUBING PUMPS

TYPES AND MAKES OF TUBING PUMPS

Seating arrangement Pump Pump Tubing Tubing THM tubing pump with mechanical seating
Pump designation arrangement acc. to API, schematically
of standing valve bore, mm bore, in size, mm size, in
60.3 2 3/8 20-125 ТHМ
31.8 1 1/4
73.0 2 7/8 25-125 ТHМ
Acc. to API Spec. 11AX Coupling
with bayonet fishing 60.3 2 3/8 20-175 ТHМ (ТNС)
tool (TNM) or with 44.5 1 3/4
cup seating arrange- 73.0 2 7/8 25-175 ТHМ (ТNС)
ment (TNS) 57.2 2 1/4 73.0 2 7/8 25-225 ТHМ (ТNС)
Plunger
69.9 2 3/4 88.9 3 1/2 30-275 ТHМ

31.8 1 1/4 73.0 2 7/8 25-125 ТHМ-К

Special (taper) 44.5 1 3/4 73.0 2 7/8 25-175 ТHМ-К
57.2 2 1/4 73.0 2 7/8 25-225 ТHМ-К
31.8 1 1/4 73.0 2 7/8 25-125 ТHМ-Т
Barrel
Non-removable valve 44.5 1 3/4 73.0 2 7/8 25-175 ТHМ-Т
(additional drain valve
of SKOK type is used) 57.2 2 1/4 73.0 2 7/8 25-225 ТHМ-Т
69.9 2 3/4 88.9 3 1/2 30-275 ТHМ-Т
25-125 ТHМ-Т
31.8 1 1/4 73.0 2 7/8
11 -10-2-2
25-175 ТHМ-Т
Non-removable valve, 44.5 1 3/4 73.0 2 7/8
11 -10-2-2
long plunger (10 feet),
barrel with side hole 25-225 ТHМ-Т
57.2 2 1/4 73.0 2 7/8
11 -10-2-2
30-275 ТHМ-Т
69.9 2 3/4 88.9 3 1/2
11-10-2-2
31.8 1 1/4 73.0 2 7/8 25-125 ТHМ-С(СС)

Non-removable single 38.1 1 1/2 73.0 2 7/8 25-150 ТHМ-С(СС) Coupling

(S) or doubled (SS)
44.5 1 3/4 73.0 2 7/8 25-175 ТHМ-С(СС)
valve with built-in
drain beating device 57.2 2 1/4 73.0 2 7/8 25-225 ТHМ-С(СС)
Traveling
Extension valve
69.9 2 3/4 88.9 3 1/2 30-275 ТHМ-С
nipple

Designation of pumps (except ТHМ-Т 11-10-2-2) is given without lengths of barrel, plunger
and extensions which shall be selected for each size of pump, depending on required plunger
stroke. Coupling
Fishing
Seating bush
PLUNGER STROKE FOR STANDARD ( THM) TUBING PUMPS BASED ON THE COMBINA- nipple

TION OF THE LENGTHS OF THE BARREL — PLUNGER — EXTENSIONS

Barrel - plunger - extension - extension Maximum plunger stroke (stop-to-stop), m

7-4-2-2 1.5
Fishing
9-4-2-2 2.1 pin
11-4-2-2 2.7
11-4-2-3 3.0
14-4-2-2 3.6
Standing
11-10-2-2 3.0
valve
22-4-2-2 6.0
14-5-1,5-1,5 3.2
22-4-2-2 6.2

EXAMPLE OF TUBING PUMP DESIGNATION

Diameter 44.5 mm, standard seating arrangement of standing valve (acc. to API), length of
barrel – 11 feet, length of plunger – 4 feet, length of extensions – 2 feet each, for installation Anchor
in tubing with diameter 73 mm: mandrel
25-175 ТHМ 11-4-2-2.

44
 ABOUT IZHNEFTEMASH
Oil production equipment

TUBING PUMPS OF SPECIAL DESIGN

Pumps ТНМ-Т with diameters 32, 44, 57 and 70 mm with non-removable standing Pump with non-removable
standing valve of THM-T type
valve.

Standing valve is set in the bottom of pump instead of seating nipple; fishing tool is not
available. Diameter of standing valve (seat and ball) for pumps with diameters 32,44,57
mm is oversized, providing more stable pump operation (free of valve sticking, oc-
curred because of paraffin deposits). Pumps are used together with drain valve (SKOK
type or other) placed above pump to drain fluid from tubing when pump is pulled out.

The following makes are developed on the base of THM-T pumps:

• pumps with non-removable standing valve, barrel with side drain hole and long
plunger (10 feet) (ТHМ – Т 11-10-2-2). Plunger is fitted so that side hole of barrel is
constantly covered by plunger; plunger stroke is 3 m. When plunger is in its lower
position (at its stop) and when it is pulled out from barrel, drain hole is opened
to ensure drain of fluid from tubing both when plunger is pulled out on rods and
when rods and plunger components are parted or unscrewed; direct flushing at
well completion is provided as well.
Plunger
• pumps with side standing valve (BVK).
The plant produces BVK valves for THM-T tubing pumps with diameters of 32 and
44 mm. BVK valve is delivered optionally and set under barrel instead of bottom
part of a pump.
In pumps equipped with BVK valves dead space is almost zero in a barrel, when
a plunger is in its lower position. This allows to operate wells with insignificant
pump working submergence without risk of failure of fluid feed due to pump
blocking by gas.

• pumps with non-removable single (THM-C) or doubled (THM-CC) standing valve

Traveling
and built-in drain beating device. valve
Diameter of standing valve (seat and ball) in pumps of diameters 32, 44, 57 mm is Non -removable
standing valve
oversized. Fishing tool is not available.
Fluid is drained from tubing through a hole in beating screw which is broken with
beating tool thrown into well.

Side standing valve, model BVK Pump THM-S Pump THM-SS

Beating
Standing screw
valve with gasket
Beating
screw
with gasket

Filter Standing
valves
Standing
valve
Thrust bush

Settler

Plug

45
 ABOUT IZHNEFTEMASH
Oil production equipment

Couplings
TUBING COUPLINGS

Tubing couplings are intended for the connection of tubing pipes, as well as for the connection of downhole equipment with tubing
threads used for the operation of oil and gas wells.

Tubing couplings of Izhneftemash Company are manufactured according to GOST 633-80 on modern program-controlled lathes and
band saws providing high productivity and accuracy of part machining.

IZHNEFTEMASH TUBING COUPLINGS:

• with plain ends (NUE):

- couplings for tubulars of nominal diameter 60 mm, grade D, Е, К;
- couplings for tubulars of nominal diameter 73 mm, grade D, Е, К, L;
- couplings for tubulars of nominal diameter 89 mm, grade D, Е, К, L.

• With upset ends:

- couplings for tubulars of nominal diameter 60 mm, grade D, К;
- couplings for tubulars of nominal diameter 73 mm, grade D, К, Е.

CASING COUPLINGS

Casing couplings are intended for the connection of casing pipes, used for the casing of oil and gas wells.

IZHNEFTEMASH CASING COUPLINGS:

• for buttress casing pipes – ОТТМ:

- for tubulars of nominal diameter 102 mm, grade D, К, Е, L, М;
- for tubulars of nominal diameter 114 mm, grade D, К, Е, L, М;
Design А.

46
 ABOUT IZHNEFTEMASH
Oil production equipment

DOWNHOLE EQUIPMENT WELL MIXER SS-89

Well mixer design allows:

• To mix fluids from two formations divided by a packer during their one lift dual com-
pletion with electrical submersible pumping system (esp) for the lower formation and
with subsurface sucker rod pump of RHM-T type for the upper formation Seating nipple,
top part
• To install RHM-T pump. Sealing ring

Advantages:
Seating nipple,
• Safety filter protects from mechanical impurities during srp suction
bottom part

• Valve and seat has an increased flow area compared with analogs. Adapter sub

Equipment parameters Value

Valve cage
Connecting thread, GOST 633-80 89

Overall dimension, mm, not more: Valve ball

- diameter of circumscribed circle 123.5 Valve seat

- length 700 Seat holder

Diameter of axle channels (for ESP systems), mm 17 (6 holes)

Enclosure
Diameter of side channels (for SRP), mm 19 (2 holes)
Dimensions of filter slots (for SRP), mm 3 × 25 (36 slots) Filter

Ball and seat (valve V11-225):

Body
- material SS 95 х 18
- ball dia., mm 34.925
- seat ID, mm 26.570

With upset ends:

Operation conditions:

- operation environment Oil, gas, water

-working temperature, °С, not more 100

- head, m, not more 1500

AUTOMATIC TRACTIVE CONNECTIONS

Rod coupling

This device is intended for connecting sucker rod string with a pump installed in a well.

Automatic tractive connections allows:

• To run rod pumps installed in seating nipple with tubing string Nut

• To run tubing pumps with plunger installed in barrel.

Before running of a pump, the lower part of tractive connection is screwed to plunger or plunger
rod, while the upper part is fixed to bottom of sucker rod string. When running the sucker rod Collet

string, the upper part enters into the lower part, collet is locked in coupling ensuring a reliable
connection between sucker rod string and pump plunger.

Size and makes,

Plunger rod
Technical characteristics

Parameter/type АС-19/60 АС – 19/73 АС-22/89

Connecting thread, GOST 13877-96 Ш19 Ш19 Ш22

73.0
Tubing dia., mm 60.3 73.0
89.0 Coupling

Holddown, kN 75 100 100

Overall dimensions (in tractive position), mm:
- length 477 473 473
- dia. 42 50 50
Weight, kg, not more 3.3 4.3 4.5

47
 ABOUT IZHNEFTEMASH
Oil production equipment

SAFETY FILTERS

Well strainers are intended for protection of a pump from foreign particles of more than 3 mm.

Filter is a tube with welded plug and holes of 3 mm in diameter. Top end of a tube has LP connecting
thread (line pipe, tapered), which matches internal thread in the lower part of a pump, or that of RHBM
seating nipple.

Parameter/type Filter 1˝ Filter 1 ¹/₄˝ Filter 1 ¹/₂˝ Filter 2˝

Thread dia., LP 1˝ 1 ¹/₄˝ 1 ¹/₂˝ 2˝

OD, mm 34 42,5 48,3 60,3

ID, mm 24 32 40,3 50,3

Length, mm 210
Total area of Ø 3mm holes 720 (102 holes) 1080 (153 holes) 1440 (204 holes)

Weight, kg, not more 0.75 1.00 0.85 1.50

SPRING WELL STRAINER FSP-73/89

Filter element in a strainer is a spring.

FSP filter is set under sucker rod pump in NKT-73 tubing string. It is intended for preventing pumps from
mechanical particles of more than 0.2... 0.8 mm in size. Clearance between spring coils is adjusted to
control particles size.

Filter is self-cleaning; spring filter element is cleaned out when valve (ball-seat) moves axially during
sucker rod pump operation.

Equipment parameters Value

Connecting thread Tubing 73

Overall dimensions, mm, not more:

- length 900

- diameter 89
Weight, kg, not more 15

48
 ABOUT IZHNEFTEMASH
Oil production equipment

SLUDGE TRAP AFNI. 631632.001

Sludge trap is installed under a pump and is intended for desludging of

produced fluid from foreign impurities (sludge). Tubing thread

Equipment parameters Value

Connecting thread according to GOST 633-80 Tubing 73

Filtering holes:

- diameter, mm 5

- number 44

- total area, mm2 860

Overall dimensions, mm, not more:

- diameter 90

- length 1346

Weight, kg, not more 7

49
 ABOUT IZHNEFTEMASH
Oil production equipment

WELL STRAINER FSP-73/105 coupling

Well strainer is intended for filtering of produced substances from foreign impurities, centralizer
sand and other mechanical impurities from well. Strainer operation is possible together pipe
with downhole pumping equipment. Well strainer can be operated in moderate and cold
macroclimatic areas.
filtering element

Parameter Value

Pipe string nominal size Tubing 73

Dimensions of filter slots, mm 3 × 150 (16 slots)

Flow area, mm² 7128

Flow area inside the pipe, mm² 3017

Overall dimensions, mm, not more: adjusting o-ring

lock pin
- length 1670

- diameter 120

Weight, kg, not more 26

end cup

GAS ANCHOR To the pump

Gas anchor is intended for gas separation from oil pumped by sucker rod pumps. As a Tubing coupling
rule, up to three gas anchors connected to each other are used. They are screwed on a
tubing string under a pump and they serve as an outer suction pipe. Tubing pipe plugged Suction pipe
with a cup is connected to a bottom anchor. Internal suction tube, entering into the
bottom (plugged) tubing pipe is screwed on into pump inlet. Gas
(into annulus)
Internal suction pipe is not included in delivery set of a gas anchor.

Gas anchor Gas anchor Gas anchor

Parameter/type
2 ³/₈˝ (60) 2 ⁷/₈˝(73) 3 ¹/₂˝ (89)
Formation fluid
Connecting thread according with gas
Tubing 60 Tubing 73 Tubing 89
to GOST 633-80
Anchor pipe dia., mm 60.3 73 88.9
Anchor cup dia., mm 79 94 109
Anchor length, mm 1010 1020 1030
Number of Ø8mm holes 96 120 144 Fluid
Weight, kg, not more 8 12 16 Cup

50
 ABOUT IZHNEFTEMASH
Oil production equipment

PRESSURE VALVE КО-73

Pressure valve KO-73 is intended for interval pressure testing of tubing string when run-
ning down centrifugal pump, as well as for shutting off fluid flow when pump stops.

It is used during well operation without sucker rods and is installed in tubing string above
a pump.

Equipment parameters Value Valve cage

Tubing dia., mm 73
Valve ball
Pressure, mPa 15

Overall dimensions, mm, not more:

- OD 73
- height 264
Weight, kg, not more 5.5

BACKFLUSH VALVE KP 73-15

It is intended for fluid delivery through the string downhole annulus inside tubing when
carrying out process operations.
Valve cage
It is installed in a tubing string at the required depth. Ball

Valve seat
Equipment parameters Value

Tubing dia., mm 73 Filter

Pressure, mPa 15

Overall dimensions, mm, not more:

- OD 120
- height 405
Weight, kg, not more 7.3

Plug
DRAIN VALVE SKOK
Tear-off shank
Detachable drain valve is intended for fluid drain out of tubing string. When used in Piston
combination with tubing pump and non-removable standing valve (THM-T), drain valve is
Drain hole
installed on upper coupling of a pump or in tubing string above a pump.

In order to reuse a valve, it is necessary to install a new tear-off shank. Shanks are included Support
in a spare parts delivery set.

To drain fluid out of tubing string when running a pump, pressure required for valve
operation is produced in the string. At the same time, neck of tear-off shank breaks. After
that, valve piston comes out of a barrel and lets drain fluid pass through holes of valve
cage into annulus. When ordering, specify valve designation and operating pressure (if not
specified, valves are delivered with operating pressure of 20 MPa).

Equipment parameters SKOK-50-N SKOK-70-N

Tubing thread 2 ⁷/₈˝ (73 mm) 3 ¹/₂˝(88,9 mm)

Drain hole dia., mm 10 (2 holes)

Circumcircle dia., mm 124 143

Valve length, mm 330

Actuation pressure, mPa 10.0 to 20.0 as per customer's request
Weight, kg, not more 7.2 9.2

51
 ABOUT IZHNEFTEMASH
Oil production equipment

SHUTDOWN VALVE KON

Fitting (only in KON-1.00)

Shutdown valve is intended for well overhaul without their killing if pumps are
changed without tubing pull-out. It is installed under seating nipple of rod pump.

Before first running of a pump, under the action of formation pressure and a spring Shaft spindle
a valve (seat-ball) is closed, side holes in valve cage are opened, through which fluid
flows in tubing. Shaft

When setting a pump in seating nipple, it pushes a shaft spindle. A spindle moves
piston and a ball, a piston closes side holes, valve is opened, providing suction of fluid
during pump operation. Safety ring

When pulling a pump, a piston stays in the same position (side holes are closed), ball Cage
affected by formation pressure and spring, closes valve, preventing fluid flow into
tubing, at the same time shaft easily moves upwards. At the next running of a pump,
the valve is opened again with the help of the shaft.

Seating nipple Weight, kg, not

Valve Pup type Connecting thread Length, mm Diameter, mm
type more

KON-1.00 25/20- ... RHM-T 4011 6-MT-ZUS Tubing 2 3/8" (60) 472 89 10.4

GAS-SAND ANCHOR
Scheme of gas-sand
Gas-sand anchor is intended for separation of gas and mechanical impurities includ- anchor operation
ed in well fluid. Gas-sand anchor is mounted in the sucker rod pump suction pipe.
It is recommended to install a sludge collecting pipe below gas-sand anchor for Coupling, Thread NKT –
collecting mechanical impurities. 60, 73, 89

Gas-sand anchor allows:

• To prevent sand removing Adapter sub

• To increase pump efficiency

Suction pipe
• To eliminate pump clogging and to increase its reliability
• To increase time between repairs of well
Dimpled shroud

Grooved casing

Adapter sub

52
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Equipment for well cementing

NC-320 CEMENTING PUMP FOR UNB PUMP UNITS

Horizontal, two-piston, double action, with built-in worm reducer of high load capacity.

Purpose

Intended for pumping the fluid media (clay, cement, saline mud) during squeezing and flashing oper-
ations in oil and gas wells when performing drilling and overhaul.

The NC-320 pump is designed on the base of 9T pump; the main parts and assembly units are inter-
changeable.

The application of the worm-and-worm gear, the one-piece stamped plate and other components of
advanced design and engineering results in reliability and long life of the NC-320 pump as compared
with 9T pump.

Equipment parameters Value

Pump useful output, kW 108

Gear ratio of worm-and-worm gear 22

Overall dimensions, mm 2385 × 750 × 2390

Weight, kg, not more 2890

PUMP PRESSURE AND THEORETICAL CAPACITY

Number of piston Changeable sleeve dia., Theoretical capacity, Theoretical capacity,

double strokes mm dm3/c (m3/h) dm3/c (m3/h)

90 12.3 (44.3) 8.8

100 15.6 (56.2) 6. 9
133
115 21.3 (76.7) 5.1
127 26.3 (94.7) 4.1
90 6.34 (22.82) 17.0
100 7.39 (28.56) 13.6
68
115 10.88 (39.17) 9.9
127 13.37 (48.14) 8.1
90 2.8 (10.1) 38.6
100 3.5 (12.6) 30.9
30
115 4.8 (17.3) 22.5
127 5.9 (21.2) 18.3

UNB PUMP UNITS

Oilfield pump units are intended for injection of working fluid during well cementa-
tion, hydrofracturing, hydraulic jet perforating, sand plug flushing, drilling, sidetrack-
ing and other flushing and squeezing operations at oil and gas fields.

A wide range of pump units (UNB types) is produced. They differ by type of high
pressure pump, mounting base, water-feeding unit, any additional devices and sys-
tems.

The following high pressure pumps are used in pump units:

• Two-piston double-action pump NC-320

• Three-plunger pump NTP with horsepower of 175 hp
At the customer’s request, all pump units may be equipped with cementing control system SKCS.
Cementing control system consists of measuring device, power supply and computer. It provides
measuring, recording and control of well cementing parameters. Results (reports) are displayed in
the form of tables and diagrams during the whole well cementing process.

53
 ABOUT IZHNEFTEMASH
Equipment for well cementing

PUMP UNITS EQUIPPED WITH NC-320 HIGH PRESSURE PUMP

Makes of pump unit:

• With tank (measuring tank with bottom valves) and water feeding unit on
the truck chassis
• With tank (measuring tank with bottom valves) without water feeding unit
on the truck chassis
• Without bunker and water feeding unit, on trailer chassis
• With bunker and water feeding unit, skid-mounted (stationary make)

Item Wheel base Water feeding unit Measuring tank, m3 Design

On truck chassis w/water feeding unit

UNB-125х32U Ural-4320 3M3/D242+TsNS 6 -
UNB-125х32K KamAZ-43118 3M3/D242+TsNS 6 SC
On truck chassis w/o water feeding unit
UNB-125х32U Ural-4320 - 6 -
UNB-125х32K KamAZ-43118 - 6 -
On trailer
Drive YaMЗ-238+gear-
UN-125х32P NefAZ-8332 - -
box, tent/container
Skid-mounted
Hydraulic drive/
UNB-125х32С Skid 5 Ural cab w/ drive YaMЗ
D242+TsNS
UNB-125х32С Skid - 5 Drive YaMЗ +gearbox
In container
UN-125х32 Container - - Drive YaMЗ +gearbox
Water feeding module
AN-30B Skid 3M3+TsNS - -
ЗMЗ - Motor 3M3-511; D242- motor D242; TsNS- pump TsNS 38-154; SC – sleeper cab

THREE-PLUNGER PUMPS NTP

NTP-175

NTP-175 is a three-plunger pump with the built-in reducer and changeable plungers. It is
available to perform a quick replacement of plungers of other diameters.

NTP-175 Pump is used instead of NC-320 Pump on UNB-125xP Units as a power pump.

The design of the pump by location of the shaft end:

• Right-hand – NTP-175 (P)

• Left-hand - NTP-175 (L)

Maximum pressure, mPa / Maximum theoretical capacity,

Designation (modification code) Plunger dia., mm
at pumping rate, l/s l/s / at pressure, mPa
NTP-175х50(L) 90 50/2.4 10.2/12
NTP-175х40(L) 100 40/2.9 12.5/10
NTP-175х32(L) 110 32/3.75 15.2/8.0
NTP-175х25(L) 125 25/4.8 20/6.0

Equipment parameters Value

Power consumption, kW (hp) 129 (175)

Plunger stroke length, mm 160
Overall dimensions, mm 1770 × 1050 × 890
Weight, kg 2250
Maximum speed of main shaft, min -1 250

54
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Maximum pressure and theoretical capacity

Feed per main at plunger double stroke rate, min -1
Plunger dia., mm
shaft rotation
40 60 100 120 200

mm dm3/rev mPa dm3/s mPa dm3/s mPa dm3/s mPa dm3/s mPa dm3/s
90 3.05 50 2.03 39 3.05 21 5.09 19 6.1 12 10.2
100 3.77 40 2.51 32 3.77 19 6.3 16 7.54 10 12.5
110 4.56 32 3.03 26 4.56 16 7.62 13 9.12 8 15.2
125 5.89 25 3.92 20 5.89 12 9.84 10 11.8 6 20

NTP-175M

Three-plunger pump NTP-175M is intended for liquid injection during wellbore cementing
operations and hydrofracturing for enhanced recovery.

Pump design by location of the shaft end:

• NTP-175M – from the right
• NTP-175M (L) – from the left.

Maximum pressure, mPa / Maximum theoretical capacity,

Designation (modification code) Plunger dia., mm
at pumping rate, l/s l/s / at pressure, mPa
NTP-175Mх50(L) 90 63/2.8 10.2/14
NTP-175Mх40(L) 100 50/3.7 12.5/12
NTP-175Mх32(L) 110 40/4.5 15.2/10
NTP-175Mх25(L) 125 32/5.6 20/9

Equipment parameters Value

Pump capacity at continuous mode, hp 250

Plunger stroke length, mm 160
Changeable plunger dia., mm 90; 100; 110; 125
Overall dimensions, mm 1770 × 1050 × 890
Weight, kg 2600

Maximum pressure and theoretical capacity

Feed per main at plunger double stroke rate, min -1
Plunger dia., mm
shaft rotation
40 60 100 120 200

mm dm3/rev mPa dm3/s mPa dm3/s mPa dm3/s mPa dm3/s mPa dm3/s
90 3.05 63 2.03 58 3.05 36 5.09 29 6.1 14 10.2
100 3.77 50 2.51 57 3.77 29 6.3 24 7.54 12 12.5
110 4.56 40 3.03 39 4.56 24 7.62 20 9.12 10 15.2
125 5.89 32 3.92 32 5.89 19 9.84 15 11.8 9 20

Maximum pressure, Maximum theoretical Water feeding unit

Type (model),
Wheel base mPa (90mm plunger capacity, l/s (125mm
designation
dia.) plunger dia.) Drive Pump

UNB125х50K KamAZ 43118 50 20 ЗMЗ/D242 TsNS

55
 ABOUT IZHNEFTEMASH
Equipment for well cementing

UNB2-250X50K MOBILE TWO-PUMP UNIT

It is intended for preparation of grouting mortar and injection of different liquid media
in oil and gas wells at cementation, abrasive jet perforation, sand washing, preflush and
overflush operations performed during development and workover of oil and gas wells.
Advantages:
• Comfortability – a cab is additionally heat-insulated, thus providing comfortable work of an
operator under low temperatures
• Reliability – duplicate power unit and pumps unit provide reliable unit operation even if one of them is broken
• Economical efficiency - thanks to UNB2-250x50K Unit, the number of special-purpose equipment can be reduced. Thus, significant
economy may be achieved on spare parts and other charges connected with operation, maintenance, and storage of special-purpose
equipment
• Batch production – all units and components used in UNB2-250x50K Unit are batch-produced
• Productivity – two high-pressure pumps allows reduction of time for operation, thus increasing the unit productivity as compared
with batch-produced UNB-125x50K Unit
• Safety – availability of covers, handrails and safeguards on site provides safe operation

Equipment parameters Value

Wheel base: KamAZ-63501 truck chassis

- wheel arrangement 8×8

Power unit, 2 pcs.:

- motor YaMЗ-236

- capacity, kW 165

- gearbox YaMЗ-238 VM

High pressure pump, 2 pcs.: NTP-175, three-plunger

- changeable plunger dia., mm 90, 100, 110, 125

- maximum capacity, hp (kW) 175 (129)

- Maximum pressure, mPa (kg ⁄cm2 ) (Ø 90mm plunger) 50 (500)

- maximum theoretical capacity, l/s (Ø 125mm plunger) 20

Measuring tank: Double-section

- volume, m3 6

Water feeding pump: TsNS 60-165

- rate, l/s 17
- drive From the chassis power take-off via drive shafts

Or booster pump Centrifugal pump 6 × 5 × 11

- rate, l/s 50

- pressure, mPa 0.3

Manifold:

- discharge pipeline dia., mm 50

- intake pipeline dia., mm 125/100

- cementing tank capacity 0.25

Overall dimensions, mm (in)

- length 11 300

- width 2550

- height 4000

Weight, kg 26 650

- front axle / rear axle, kg 11 200/15 450

56
 ABOUT IZHNEFTEMASH
Equipment for well cementing

UNB-200X70M ( 93UNB) PUMP UNIT

Pump unit UNB-200х70M is intended for injection of various liquid

media for well cementing during well drilling, completion, workover,
hydrofracturing, abrasive jet perforation, sand washing, sidetracking
and other preflush and overflush operations in oil and gas wells.

Specific features of the unit:

• A new, more powerful pump NTP-175M providing pressure up to

70 mPa – this is 40% more than that of the NTP-175 pump.
• MAZ chassis has the technical capabilities of the box power
output up to 278 kW. This chassis has a significant reserve for
aggregating with even higher pressure pumps.

Equipment parameters Value

Wheelbase: MAZ 6317F9, 6 × 6

High pressure pump, 2 pcs.: NTP-175M
- changeable plunger dia., mm 90; 100; 110; 125
- pup capacity at continuous mode, hp 250
- maximum pressure (90mm dia.plunger), mPa 63
- maximum theoretical capacity (125mm dia.plunger), dm3/s 20
Overall dimensions, mm, not more:
- length 9590
- width 2550
- height 3805
Total weight of the unit, kg 24 900

57
 ABOUT IZHNEFTEMASH
Equipment for well cementing

UNB-125Х50SО ( 72 UNB) PUMP UNIT

UNB-125х50SО Pump unit is intended for transportation of dry pow-

dered materials (cement, grouting mixtures, etc.), preparation of grout-
ing mortars, their accumulating and mixing, injection of liquid media
during overhaul and other preflush and overflush operations performed
during development and workover of oil and gas wells.

Advantages:

• This unit may be used instead of 2 units: cementing unit UNB-

125х32 , mixing unit US-50х14
• It may be operated in complex with other units, as well as by itself
• The unit allows to deliver up to 5 tons (11020 LB) of cement to the
well, to prepare cement mixture of required density and to inject
in the well
• It includes modernized pump with improved operating characteristics and serviceability
• ODN pump is used for delivery of water in measuring tank, mixing tank, as well as for washing of these tanks and all the manifold
• In cold season NTP-175 Pump and manifold are heated with exhaust gases during unit transportation to field

Equipment parameters Value

Wheelbase KamAZ-63501 chassis
- wheel arrangement 8 х8
- motor capacity, kW, not less 260
High pressure pump NTP-175х40 *
- plunger dia., mm 100*
- gear ratio of built-in gear reducer 5.06*
- power consumption, hp (kW) 175 (129)*
- maximum pressure, mPa (kg/cm2) 40.0 (400)*
- maximum theoretical capacity, dm3/s (l/min) 15.7 (942)*
Bunker for dry mixtures storage and transportation
- volume, m3, not less 4
- weight of transported material, t, not more 5
- cement unloading Auger-type
- auger drive Hydraulic
Measuring tank
- volume, m3, not less 6
Mixing tank w/agitator:
- volume, m3, not less 5.5
- agitator 2 pcs.
- agitator type Vertical bladed
- agitator drive Hydraulic
Mixing type Feed of dry material by auger to grouting fluid
Water feed pump ODN 120-100-65
- maximum rate, l/s 15
- head, m 13
- drive Hydraulic
Parameters of drive hydraulic system:
Maximum pressure, bar 200
Hydraulic tanl capacity, l 150

58
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Equipment parameters Value

Manifold:
Nominal diameter of pipelines flow areas, mm
- intake line 125
- discharge line 50
Unit control:
- hydraulic equipment From the console at the operator’s site
- electrical equipment From the console at the driver's cab
Overall dimensions of the unit, mm 10500 х 2550 х 3940
Total weight of the unit, kg 24150
Total weight distribution on road, kg:
- via front bogie 11200
- via rear bogie 12950

* The above characteristics are given for a pump with 100mm dia. plunger.
The pump may be delivered with plungers of dia. 125, 110, 100 and 90mm. The delivery package may additionally include a plunger of any diameter
at customer's option.

59
 ABOUT IZHNEFTEMASH
Equipment for well cementing

MIXING UNITS US

Mixing unit with bunker US-50Х14(20)

The units are intended for the transportation of dry powdered materials (cement,
grouting mixtures, sand and other bulk materials), preparation of grouting
mortars and other sand-liquid slurries during cementing of oil and gas wells.

The materials are pneumatically delivered to the bunker by a screw conveyor

through the feeding tube (loading through the upper hatch is possible). To
prevent arching of the grouting material in the bunker, a vibrator is installed. The
cement is fed into the mixing device using two augers.

The units are equipped with slit-shaped nozzles with different flow areas for
selecting the required density of the prepared grouting mortar.

Value
Equipment parameters
US-50х14U US-50х14K US-50х20K US-50х20DS

Skid, drive D242,

Wheelbase (skid) Ural-4320 KamAZ-43118/65111 KamAZ-63501/43118
GAZ-3307 cab

Bunker capacity, m³ 14.5 14.5 20.0 20,0

Weight of transported material, t 8.0 8.5/11.4 11.5/8.0 15,0

Additional loading in the bunker at the site of cementing

18 18 25 25
operations, t, not more

Mixing hydrovvac unit:

- liquid pressure, МПа (optimal/maximum) 1.5/2.0

- density of prepared mud, g/cm³ 1.3...2.4

- maximum make-up of grouting mortar with density

27.0
1,85 g/cm³, dm³/s

- time required for preparation of mud with given

40
density, s

Overall dimensions, mm:

- length 9400 9000 10 400/9400 9800

- width 2550 2550 2550 2820
- height 3700 3800/3700 3800/3700 3300

Weight, kg (total) 21200 21970/24820 27200/22100 8500 (empty)

60
 ABOUT IZHNEFTEMASH
Equipment for well cementing

US-50-8Х8 MIXING UNIT WITH BUNKER AND SURGE TANK

Equipment parameters Value

Wheelbase KamAZ-43118

Bunker capacity, m³ 6.0

Weight of transported material, t 6.5
Mixing hydrovvac unit :
- density of prepared mud, g/cm³ 1.3...2.4
- maximum make-up of grouting mortar with density 1,85 g/cm³, dm³/s 27.0
Number of dosing augers 2
Surge tank capacity, m³ 6.0
Number of mixers 3
Unit overall dimensions, mm:
- length 8600
- width 2550
- height 3800
Weight, kg (total) 20600

USP-USP-20K PORTABLE MIXING AND SURGE UNIT

USP-20K portable mixing and surge unit is intended for holding and
homogenization of mud in the tank by its mixing by a belt auger.

Advantages:

• The unit is equipped with a big tank with total capacity of 20 m3,
divided into two equal parts for simultaneous preparation two
different muds.
• the tank is equipped with rotating augers to create and maintain a
uniform density of the prepared mud.
• The unit may be arranged with a single-section or two-section
tank.

Equipment parameters Value

Wheelbase KamAZ-43118

- wheel arrangement 6×6

- capacity, kW 200

Tank Two-section/single-section

- capacity, m3 2 × 10/20

- slope angle of tank bottom, deg. 1.5

Augers Screw-type, two-start

- drive From chassis engine

Mud preparation system n/a*
Unloading supports, drive type mechanical
Unit overall dimensions, mm: 9500 × 2550 × 4000
Total weight, kg, not more 17 770
Curb weight, kg 17 470

* It is possible to install an ejection funnel on request.

61
 ABOUT IZHNEFTEMASH
Equipment for well cementing

USP-16U PORTABLE MIXING AND SURGE UNIT

USP-16U portable mixing and surge unit is intended for holding and
homogenization of mud in the tank by its mixing by a belt auger.

Equipment parameters Value

Wheelbase Ural-4320

- wheel arrangement 6×6

Tank Two-section/single-section

- capacity, m3 2 × 8/16

- slope angle of tank bottom, deg. 1.5

Augers Screw type

- drive From chassis engine

Manifold: nominal diameter of pipeline flow areas, mm:
- loading lines 50, 100
- discharge lines 100
Unit overall dimensions, mm: 9200 × 2550 × 4000
Total weight, kg, not more 15 500

62
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Unified Components of Pumps

and Pump Units
SAFETY VALVES

Characteristic features of safety valves:

• Accurate and stable response due to self-detachable and self-cleaning lock
• Long service life of a lock
• Reduced hydraulic blow during valve response
• Better safety

KPS

Single-action valves with shear rods are intended for high-pressure oilfield equipment. The range
of pressure relief cracking pressure is from 5 to 70 MPa (from 725.2 to 10,150 psi). Nominal inter-
nal diameter is 50 mm (1.969 in) for oil and gas equipment working under high pressure.

KPSD

Single-action differential valves with shear rods are intended for high-pressure oilfield equip-
ment. The range of pressure relief cracking pressure is from 16 to 105 MPa (from 2,321 to 15,230
psi). Nominal internal diameter is 50 mm (1.969 in) for oil and gas equipment working under high
pressure.

SBT 40/50 AND SBT 70/50 QUICK-ASSEMBLY TUBING JOINTS

Joints are used in oil field high-pressure equipment. The joints are characterized by long life and
high impermeability with low torque strengthening.

KPN UNIVERSAL VALVE COMPONENTS

The valve components of standard and acid-resistant designs are used in oil field high-pressure
piston and plunger pumps.
The valve components are characterized by their long life, simple design, high volumetric
efficiency due to the material, thread-free cups fastening, lock configurations and improved
hydrodynamics.

KSH 25 х 70 AND KSH 50 х 70 STOP BALL COCKS

Ball cocks are intended for locking of nonaggressive fluids in pipelines.

63
 ABOUT IZHNEFTEMASH
Equipment for well cementing

SINGLE JOINTED ELBOW KSHI AND DOUBLE JOINTED ELBOW KSHI-2

Jointed elbows are intended for piping different units with each other and with wellhead to inject
fluid media when cementing wells, carrying out bottomhole treatment and other operations.

КО AND КОV CHECK VALVES

Check valves and check valves with pressure relief gate, of standard and acid-resistant designs are
used as a part of oil and gas high-pressure equipment. Conditional pass – 50 mm (1.969 in). The
valves are characterized by reliability, long service life, compactness and tightness.

SEALING PACKS

The sealing packs of variable rigidity PUNP are used in the oil field high-pressure plunger pumps
for plungers of 80, 90, 100, 110, 125, 140 mm in diameter.
These new items are characterized by their corrosive resistance, high impermeability, long
service life due to the cup packs manufactured from the metal-polymers, prevention of abrasive
ingress on the sealing area, extrusion of the cups between the plungers and bearing sleeves.

64
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Stationary Break Out Tong

STATIONARY BREAK OUT TONG, DOUBLE SPEED, WITH PNEUMATIC DRIVE АКB-4

The double speed automatic break out tongs with pneumatic drive are used as a part of the
drilling unit for making up and breaking out drill pipes and casings in round trip operations when
drilling oil and gas wells.

Advantages:
• The torque is created without impacts, thus reducing the wear of pipes and tong retaining
blocks
• High torque allows to avoid using the wrenches
• In order to protect the threads the makeup operations are carried out with preset torque.

New versions of tongs are equipped with electronic torque control system.

Functions:
• Digital and graphical representation of current torque on a portable display
• Transmission of obtained information on PC for review and analysis of histograms of param-
eters and types of fulfilled jobs with reference to a date, time, field, number of well cluster,
crew, running in and out operations and creation of database

Automatic break out tongs consists of:

• Tong unit
• String with carriage
• Control panel
• Double-speed gear box

65
 ABOUT IZHNEFTEMASH
Equipment for well cementing

АKB- АКB-4.0-
Parameters AKB-4(3) АKB-4.0-04 АКB-4.0-05 АКB-4.0- 03/04 АКB-4.0-03/05
4.0 05/04

The tongs with

On the basis of Speed of
The tongs with fast first speed,
АКB-3М2 tongs making up and Electronic
The tongs with fast first speed hydraulic torque-
Description by capital repair breaking out of pressure gauge
fast first speed and hydraulic limiting system
and upgrade drilling pipes is is added
torque-meter and electronic
(expenditures - increased twice
torque-meter
capital repair

Frequency of rotation of
pipe-clamping device,
rpm:
- at first (fast) trans-
0…39 0…22 0…39 0…22 0…39 0…39 0…39
mission
- at second (low) trans-
0…2.6 0…1.5 0…1.5 0…1.5 0…1.5 0…1.5 0…1.5
mission
Torque, kN.m:
- at first (fast) trans-
3.0 5.0 2.8 5.0 2.8 2.8 2.8
mission
- at second (low) trans-
40 72.5 70.0 72.5 70.0 70.0 70.0
mission

Pressure gauge
at control panel Pressure gauge
(pneumohy- at control panel
draumechan- (pneumohy-
Under customer
Torque control Mechanical Electronic ical system of draumechan-
request
torque limita- ical system
tion located of torque
in the control limitation)
panel)

Pressure gauge,
Electronic
Control system - Electronic device Pressure gauge Electronic
device
device
Overall dimensions,
1730 × 1013 × 2610 1780 × 1230 × 2610
mm
Weight, kg 2700 3300

The plant supplies all original spare parts for repair of AKB-4 Tongs as well as for AKB-3M2 and
AKB-3M2.E2 produced earlier. Also the plant performs high-quality workover of equipment un-
der the technological process of main production. Produced tongs can be supplied in all designs.

There are several tongs upgrade programs according customer-specific requirements.

For example, upgrade of AKB-3M2 tongs includes the following actions:

• Workover when necessary;
• Dismantle of the flywheel and installation of double-speed gearbox instead of it;
• Installation of disk brake at the pipe-clamping device;
• Completing with control system and break-out torque limitation system on the basis of the
electronic device.

The following information shall be mentioned for making an inquiry for AKB tongs and spare
parts:

• Name and designation of the tongs;

• Name, designation and quantity of spare parts.

66
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Equipment for Well Repair and Overhaul

SUSPENDED TUBING TONGS KPT-2M

The suspended tubing tong KPT-2M is intended for using in make-and-break operations with drill
pipes and tubing during maintenance and overhaul of oil and gas wells as a port of hoisting units
of AZ-37, UPT-50, A-50, CUOPER, CREMCO and other types of unit. The tong may be operated in
moderate and cold microclimatic areas.

Advantages:

• No planetary gear reducer

• Foreign components of hydraulic system (M&S, Walvoil, Parker, Manuli)
• Enforced design, protection from external influence
• Minimum service maintenance
• Easy gear shift
• Improved ergonomics
• Increased capability (in comparison with KPT-2)
• gerotor motor (M&S).

Description:

• The hydraulic drive of the tong is operated by the hydraulic systems of the hoisting unit
• A set of hoses for connection to the hydraulic system is included in the tong delivery set
• The pipe clamping device of cam type, the locking system preventing operation with the
unlocked door is provided
• The planetary reducer and the gear box ensure two speeds of the rotator
• The tong is fastened by the compensating hanger, providing vertical travel of the tongs
• An adjustable hydraulic valve for torque limitation and torque visual control system are available

SPIDERS ZK, ZK-56

A spider is intended for holding the tubing string during well repair and overhaul, as a part of units
for subsurface repair operations and workover.

Advantages:

• A safety device protecting from accidental release of tubing string is provided in spider design
• Spider is driven pneumatically from pneumatic system of hoisting unit
• Hoses for connection to hoisting unit are delivered with a spider
• The spider ZK-56 can be driven manually by the removable lever, included in the spider (ZK)
delivery set

67
 ABOUT IZHNEFTEMASH
Equipment for well cementing

SUSPENDED SUCKER ROD TONGS KPSH-3M

Suspended sucker rod tong KPSh-3M are intended for using in make-up and break-out oper-
ations with sucker rods during development maintenance and overhaul of oil and gas wells.
Tongs may be operated as a part of repair units of A-50, A-50M, AZ-37, A32/40 and other types
of domestic and foreign units.

KPSh-3M Tongs operates on hydraulic system of hoisting unit.

Advantages:

• Small-sized high-torque orbital hydraulic motor (M&S, Bulgaria)

• Chain sling with height adjustment is used for suspension
• Disk brake instead of band brake
• Bearing units design requires minimum service maintenance
• Without planetary gear reducer
• Torque limitation
• The smallest overall dimensions and weight in comparison with similar tongs of foreign
and domestic production

Description:

• Hydraulic drive is driven from hoisting unit hydraulic system. Set of hoses for connection
to hoisting unit hydraulic system is included in a delivery set
• The tongs are mounted with the help of compensating suspension providing vertical
displacement of the tongs
• An adjustable hydraulic valve for torque limitation and torque visual control system are
available

HYDRAULIC BAILER GZH

Intended for cleaning of wells from sludge during well-workover operations.

Before running of a bailer, a container for gathering sludge is attached to the hydraulic bailer sub.

When running in a well, the pipe of a container bears against the dense layer of sludge. Retaining
screws are being cut off, a rod of hydraulic bailer moves relative to the body, compresses the
spring and opens a valve. Under well pressure, a container is filling with sludge.

As a hydraulic bailer is lifted, a valve is closed under spring action and container with sludge is
Rod
pulled together with a hydraulic bailer.

Valve

Crossover

Container

68
 ABOUT IZHNEFTEMASH
Equipment for well cementing

IRT500.102M2 SHUTDOWN VALVE

Purpose:

• IRT500.102M2 shutdown valve is intended for shutdown of internal space of production string of
oil and gas wells aiming to separate zones during replacement of downhole equipment without well
killing
• It can be used in all well types when it is necessary to replace subsurface pump equipment or flow
string
• Shutdown valve is intended for operation in all macroclimate conditions according to GOST 16350-
80

NS-73 JET PUMP

Jet pump is intended for development and hydrodynamic survey of wells.

The pump is installed in the string of the tubing NKT-73. Under the pump, a packer is set for sealing the hole
clearance.

Pump consists of:

• Housing with the central and two side channels

• A changeable insert (three designs are available)
• Injector and diffuser (installed in one or two channels)
• Depending on pump operation, one of three changeable inserts is used. The inserts are replaced using
the insert catcher without lifting the pump out of the well.
The pump provides operation in three modes:

• Reduction of the bottomhole pressure and differential pressure ( the blind insert is used)
• Hydrodynamic survey of the bed (the sealing insert and geophysical instruments are used)
• Bottomhole acid treatment (the acid protection insert is used)

69
 ABOUT IZHNEFTEMASH
Equipment for well cementing

SEALING INSERT

The sealing insert has the central channel for the cable of the geophysical instrument.
The cable is sealed with rubber rings.

BLIND INSERT

The blind insert overlaps the central channel of the pump and lets the fluid flow from the tubing to the
injectors through the side channels. When the working fluid comes out of the nozzle, the underpressure
zone is formed in the mixing tank, where the bed fluid enters and comes off in the hole clearance through
the diffuser. The reduction of the bottomhole pressure is checked by the gage, installed on the insert.

ACID PREVENTION INSERT

The central channel of the insert is closed by the valve with the spring-loaded ball. Under the impact of
the fluid pressure in the tubing the valve opens and allows the acid solution to penetrate into the bot-
tomhole formation zone with shutting off the fluid flow in the side channels.

FISHING TOOLS

Fishing spears and sucker rod sockets for external gripping, of collet type, non-releasing are intend-
ed for gripping and pulling out the tubing, bottom-hole pumps, downhole motors and sucker rods
during elimination of downhole failures.

The fishing spears and sucker rod sockets are of great popularity among the customers through their
high reliability, reached by simple construction and easy maintenance.

Assembling of fishing spears and sucker rod sockets is performed depending on the types of grip-
ping and the fish and in accordance with the given tables.

70
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Mud Pumps and Pump Units

NB MUD PUMPS

Pumps of NB type – horizontal, two-cylinder, double-action, driven, with built-in gear reducer.

The pumps are intended for delivery of the fluid into the wells when carrying out exploratory and development drilling and other oil-
field operations, as well as for pumping non-aggressive fluids.

The pneumatic compensator in the injection line provides the regular flow fluctuation and pump output fluid delivery.

Owing to their high reliability, easy operation and maintenance the pumps of NB type are of great demand among the customers.

The plant produces more than 30 types and makes of NB pumps, differed by capacity, position of the pulley, the gage and by coupling
design.

The required operation mode for pressure and volumetric supply is freely set by removing the liners and changing the number of piston
strokes.

Supply

Under customer request NB pumps can be additionally completed with a puller of valve seats and liners. The plant provides its custom-
ers with quality spare parts, and make pump overhaul under the technology of main production.

NB-32, NB-50 MUD PUMPS

The pumps are intended for injection of washer fluids (water, sludge) into the well when carrying
out oil and gas exploratory and structure drilling.

The pumps are widely used for pumping various non-aggressive fluids at the enterprises of food,
chemical and construction industries.

Parameters NB-32, NB-50

Piston stroke, mm 160

Rotational frequency of the transmission shaft (max), rpm 413 (110 double strokes)

Vacuum gage suction lift, m 3

Diameter of suction/discharge pipe, mm 113/50

Pressure and pump displacement (at 110 double piston strokes)

Diameter of changeable Pump displacement,

Pump designation (type) Useful power, kW Max pressure, MPa
liners, mm dm3/s (m3/h)

80 5.2 (18.7) 6.2

90 6.7 (24.1) 4.8
NB-32 32
100 8.5 (30.6) 3.8
110 10.4 (37.4) 3.1
90 6.7 (24.1) 7.5
100 8.5 (30.6) 5.9
NB-50 50
110 10.4 (37.4) 4.8
120 12.5 (45) 4.0

71
 ABOUT IZHNEFTEMASH
Equipment for well cementing

Main pump designs:

Design
Description Overall dimensions, mm Max weight, kg
No.
01 Pulley on the right side
1860 × 740 × 1330 1040
02 Pulley on the left side
03 With air-line coupling and a pulley on the right side
1860 × 1000 × 1330 1080
04 With air-line coupling and a pulley on the left side
05 With friction coupling and a pulley on the right side
1860 × 1000 × 1330 1180
06 With friction coupling and a pulley on the left side
07 Pulley on the right side, side pressure gauge
1860 × 740 × 1250 1040
08 Pulley on the left side, side pressure gauge
09 With air-line coupling and a pulley on the right side, side pressure gauge
1860 × 1000 × 1250 1080
10 With air-line coupling and a pulley on the left side, side pressure gauge
11 With friction coupling and a pulley on the right side, side pressure gauge
1860 × 1000 ×1250 1180
12 With friction coupling and a pulley on the left side, side pressure gauge
13 Pulley on the right side, without frame
1860 × 740 × 1230 1010
14 Pulley on the left side, without frame
15 Pulley on the right side, with electric engine
3200 × 950 × 1440 1650
16 Pulley on the left side, with electric engine
19 With air-line coupling and a pulley on the right side, with electric engine
3200 × 1240 × 1440 1960
20 With air-line coupling and a pulley on the left side, with electric engine
23 With friction coupling and a pulley on the right side, with electric engine
3200 × 1240 × 1440 2060
24 With friction coupling and a pulley on the left side, with electric engine

• For definition of the right and left sides of the pump the gaze should be directed from the pump’ hydraulic end to the power end.
• Electric engine for NB-32: power – 30 kW, shaft rotational frequency – 1000 rpm.
• Electric engine for NB -50: power – 55 kW, shaft rotational frequency – 1000 rpm.

72
 ABOUT IZHNEFTEMASH
Equipment for well cementing

PUMP NB-125IZH

Purpose:

• Injection of mud fluid during drilling of oil and gas wells;

• Injection of liquid media during preflush and overflush operations in the process of well overhaul;
• Injection of water to the reservoir for oil production stimulation;
• Pumping of different non-aggressive liquids.

Pumps can be completed with highly reliable assemblies:

• Hardened rods with chrome-nickel hard alloy plating of working area. The plating has low fric-
tion coefficient and increased corrosion- and wear-resistance;
• Rubber-fluoroplastic sealing of pistons and rods decreases wear of liners and rod, and provides
long-term reliable pump operation.

Parameters Value

Useful power, kW 125

Piston stroke, mm 250
Rotational frequency of the transmission shaft
Up to 511 (100 double piston strokes)
(max), rpm
Vacuum gage suction lift, m 3
Connection pipes:
- discharge External thread NKT 60
- suction flange Dy 100 mm

NB-125IZH design features:

Electric engine

Shaft rotation
Number of Design Overall dimensions, mm Weight, kg
frequency, Power, kW
design
rpm

NB-125IZH-27 Without pulley and frame 2610 × 890 × 1960 2810 - -

NB-125IZH-28 With pulley, without frame 2610 × 980 × 1960 3170 - -
NB-125IZH-29 With pulley and on frame 2610 × 980 × 2010 3260 - -
NB-125IZH-30 With pulley, discharge flanges, without frame 2610 × 980 × 1960 3190 - -
NB-125IZH-31 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1000
NB-125IZH-32
engine on frame
55
NB-125IZH-33 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1500
NB-125IZH-34
engine on frame
NB-125IZH-35 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1000
NB-125IZH-36 4200 × 1640 × 2120 4900
engine on frame
75
NB-125IZH-37 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1500
NB-125IZH-38
engine on frame
NB-125IZH-39 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1000
NB-125IZH-40 90
engine on frame
NB-125IZH-41 With pulley, with electric engine on frame 1500

73
 ABOUT IZHNEFTEMASH
Equipment for well cementing

With pulley discharge flanges, with electric

NB-125IZH -42 1500 90
engine on frame
NB-125IZH -43 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1000
NB-125IZH -44
engine on frame
110
NB-125IZH -45 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1500
NB-125IZH -46
engine on frame
NB-125IZH -47 With pulley, with electric engine on frame 4200 × 1640 × 2120 4900
With pulley, discharge flanges, with electric 1000
NB-125IZH -48
engine on frame
132
NB-125IZH -49 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1500
NB-125IZH -50
engine on frame
NB-125IZH -51 With pulley, with electric engine on frame
With pulley, discharge flanges, with electric 1500 160
NB-125IZH -52
engine on frame
NB-125IZH -68 With pulley, electric engine on the pump
With pulley left side design, electric engine 2610 × 970 × 2010 3350 750 22
NB-125IZH -69
on the pump
NB-125IZH- With pulley, discharge flanges, with electric
6250 × 1965 × 2915 5350 1000 200
48.01 engine on frame, with control panel and VFD

Pressure and pump displacement depending on liners diameter and piston double strokes

Pressure, MPa / displacement, dm3/c (m3/h)

Diameter of changeable liners, mm
66 double strokes 100 double strokes

90 20.5/6.1 (22.0) 13.4/9.3 (33.5)

100 16.0/7.8 (28.1) 10.6/11.8 (42.5)
115 11.8/10.6 (38.2) 7.8/16.0 (57.6)
127 9.5/13.1 (47.2) 6.3/19.8 (71.3)

74
125047, Russia, Moscow, Lesnaya St. 5B
T. +7 495 981 01 01 F. + 7 495 981 01 20
[email protected]
www.rimera.com
www.chelpipe.ru