RRB-JE 2018 2 Stage CBT Electronics Engineering: Call: 9990657855
RRB-JE 2018 2 Stage CBT Electronics Engineering: Call: 9990657855
RRB-JE 2018
2nd STAGE CBT
ELECTRONICS ENGINEERING
SAMPLE TEST PAPERS
Classroom Batches
Part-1
5) There are primarily two types of
1) Which is the microprocessor register:
comprises: a.general purpose register
a.Register section b.dedicated register
b.One or more ALU c.A and B
c.Control unit d.none of these
d.All of these Ans: c
Ans: D
6) Name of typical dedicated register is:
2) What is the store by register? a.PC
a.data b.IR
b.operands c.SP
c.memory d.All of these
d.None of these Ans: D
Ans: a
7) BCD stands for:
3) Accumulator based microprocessor a.Binary coded decimal
example are: b.Binary coded decoded
a.Intel 8085 c.Both a & b
b.Motorola 6809 d.none of these
c.A and B Ans: a
d.None of these
Ans: c 8) Which is used to store critical pieces
of data during subroutines and
4) A set of register which contain are: interrupts:
a.data a.Stack
b.memory addresses b.Queue
c.result c.Accumulator
d.all of these d.Data register
Ans: D Ans: a
20) The RAM which is created using 25) The CPU sends out a ____ signal to
bipolar transistors is called: indicate that valid data is available on
a.Dynamic RAM the data bus:
b.Static RAM a.Read
c.Permanent RAM b.Write
d.DDR RAM c.Both A and B
Ans: b d.None of these
Ans: b
21) Which type of RAM needs regular
referred: 26) The CPU removes the ___ signal to
a.Dynamic RAM complete the memory write operation:
b.Static RAM a.Read
c.Permanent RAM b.Write
d.SD RAM c.Both A and B
Ans: a d.None of these
Ans: a
22) Which RAM is created using MOS
transistors: 27) BIU STAND FOR:
a.Dynamic RAM a.Bus interface unit
b.Static RAM b.Bess interface unit
c.Permanent RAM c.A and B
d.SD RAM d.None of these
Ans: a Ans: a
31) The four index register can be used 2. In 8085 name the 16 bit registers?
for: a) Stack pointer b) Program counter c)
a.Arithmetic operation a&b
b.Multipulation operation
c.Subtraction operation 3. Which of the following is hardware
d.All of these interrupts?
Ans: a a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP
c) a & b
32) IP Stand for:
a.Instruction pointer 4. What is the RST for the TRAP?
b.Instruction purpose a) RST5.5 b) RST4.5 c) RST4
c.Instruction paints
d.None of these 5. What are level Triggering interrupts?
Ans: a a) INTR&TRAP b)RST6.5&RST5.5
c)RST7.5&RST6.5
33) CS Stand for:
a.Code segment 6. Which interrupt is not level sensitive
b.Coot segment in 8085?
c.Cost segment a) RST6.5 is a raising edge-trigging
d.Counter segment interrupt.
Ans: a b) RST7.5 is a raising edge-trigging
interrupt.
34) DS Stand for: c) a & b.
a.Data segment
b.Direct segment 7. What are software interrupts?
c.Declare segment a) RST 0 - 7 b) RST 5.5 - 7.5 c) INTR,
d.Divide segment TRAP
Ans: a
8. Which stack is used in 8085?
35) Which are the segment: a) FIFO b) LIFO c) FILO
a.CS: Code segment
b.DS: data segment 9. Why 8085 processor is called an 8 bit
c.SS: Stack segment processor?