150 WATTS REL-150

SINGLE/MULTI OUTPUT AC-DC OUTPUT SPECIFICATIONS

Total Output Power at 50°C(1) 100W Convection Cooled(16)(17)
FEATURES: (See Derating Chart) 150W Forced-Air Cooled(15)(16)(17)
• IEC 60601-1 3rd ed. Medical Cert. Output Voltage Centering Output 1:  0.5% (All outputs at 50% load)
• Compact 3.8” x 6.0” x 1.3” Size • IEC 62368-1 2nd ed. Certification Output 2:  5.0%
• 2 Year Warranty • IEC 60601-1-2 4th ed. EMC Output 3:  5.0%
• Universal 85-264V Input • Class B Emissions per EN55011/32 Output 4:  5.0%
• One to Four Outputs • RoHS Compliant Output Voltage Adjust Range Output 1: 95-105%
• High Efficiency • Optional Remote Inhibit/Enable Load Regulation Output 1: 0.5% (10-100% load change)
• 0-70°C Operating Temperature • Optional Chassis/Cover Output 2: 5.0% (10-100% load change)
(4001-5 Models) 8.0% (20-100% load change)
(2001 Model) 6.0% (20-100% load change)
Output 3: 5.0% (10-100% load change)
Output 4: 5.0% (10-100% load change)
Source Regulation Outputs 1 – 4: 0.5%
Cross Regulation Outputs 2 – 4: 5.0%
Output Noise Outputs 1 – 4: 1.0%
Turn on Overshoot None
Transient Response Outputs 1 – 4
Voltage Deviation 5.0%
Recovery Time 500S
Load Change 50% to 100%
CHASSIS/COVER OPEN FRAME
Output Overvoltage Protection Output 1: 110% to 150%
SAFETY SPECIFICATIONS Output Overpower Protection 110-160% rated Pout, cycle on/off, auto recovery
UL 62368-1:2014, 2nd Edition Hold Up Time 16mS min., Full Power, 85V Input
Underwriters Laboratories CAN/CSA-C22.2 No. 62368-1-14
Start Up Time 5 Seconds, 120V Input
File E137708/E140259 AAMI/ANSI ES60601-1:2005/(R) 2012
CAN/CSA-C22.2 No. 60601-1:2014 INPUT SPECIFICATIONS
Protection Class I
CB Reports/Certificates (including all IEC 62368-1:2014, 2nd Edition Source Voltage 85 – 264 Volts AC
National and Group Deviations) IEC 60601-1:2005/A1:2012 Frequency Range 47 – 63 Hz
Peak Inrush Current 40A
EN 62368-1:2014, 2nd Edition Efficiency 82% Typ., Full Power, 230V, varies by model
TUV SUD America
EN 60601-1:2006/A1:2013 Power Factor 0.95 (Full Power, 230V)
ENVIRONMENTAL SPECIFICATIONS
Low Voltage Directive (2014/35/EU of February 2014) Ambient Operating 0C to + 70C
RoHS Directive (Recast) (2015/863/EU of March 2015) Temperature Range Derating: See Power Rating Chart
Electrical Equipment (Safety) Regulations 2016 SI No. 1101 Ambient Storage Temp. Range - 40C to + 85C
Restriction of the Use of Certain Hazardous Substances in EEE Regulations Temperature Coefficient Outputs 1 – 4: 0.02%/C
2012 SI No. 3032 + 2019 SI No.492 GENERAL SPECIFICATIONS
MODEL LISTING Means of Protection
Primary to Secondary 2MOPP (Means of Patient Protection)
MODEL OUTPUT 1(19) OUTPUT 2(19) OUTPUT 3(18) OUTPUT 4(18) Primary to Ground 1MOPP (Means of Patient Protection)
Secondary to Ground Operational Insulation(Consult factory for 1MOPP)
REL-150-4001 +3.3V/15A(20) +5V/8A +12V/2A -12V/2A Dielectric Strength(8, 9)
REL-150-4002 +5V/15A(20) +3.3V/8A +12V/2A -12V/2A Reinforced Insulation 5656 VDC, Primary to Secondary
REL-150-4003 +5V/15A(20) +3.3V/8A +15V/2A -15V/2A Basic Insulation 2121 VDC, Primary to Ground
REL-150-4004 +5V/15A(20) -5V/8A +12V/2A -12V/2A Operational Insulation 707 VDC, Secondary to Ground
REL-150-4005 +5V/15A(20) -5V/8A +15V/2A -15V/2A Leakage Current
REL-150-4006 +5V/15A(20) +24V/3A +12V/2A -12V/2A Earth Leakage <300µA NC, <1000µA SFC
REL-150-4007 +5V/15A(20) +24V/3A +15V/2A -15V/2A Touch Current <100µA NC, <500µA SFC
REL-150-4009 +24V/2.3A +10V/1A +6V/1.6A -6V/.31A Power Fail Signal(14) Logic low with input power failure 10 ms
REL-150-4010 5V/15A(20) 12V/5A 24V/1A 24V/1A minimum prior to Output 1 dropping 1%
REL-150-3001 +5V/15A(20) +12V/4A -12V/3A Remote Inhibit (optional) Contact closure inhibits all outputs
REL-150-3002 +5V/15A(20) +15V/3A -15V/2A Remote Sense(10) 250mV compensation of output cable losses
REL-150-3003 +22V/3.5A -22V/3.5A +24V/1A Mean-Time Between Failures 100,000 Hours min., MIL-HDBK-217F, 25° C, GB
REL-150-3004 +5V/6A +12V/7A -12V/3A Weight 1.15 Lbs. Open Frame/ 1.82 Lbs. Chassis and Cover
REL-150-3005 +5.5V/15A(20) +15.5V/3A -15.5V/2A EMC SPECIFICATIONS (IEC 60601-1-2:2014, 4TH ed./IEC 61000-6-2:2005)
REL-150-2001 +3.3V/15A(20) +5V/8A Electrostatic Discharge EN 61000-4-2 8KV contact / 15KV air discharge A
REL-150-2002 +5V/15A(20) +12V/5A Radiated Electromagnetic Field EN 61000-4-3 80MHz-2.7GHz, 10V/m, 80% AM A
REL-150-2003 +5V/15A(20) +24V/3A Electrical Fast Transients/Bursts EN 61000-4-4 2 KV, 5KHz/100KHz A
REL-150-2004 +12V/7.5A -12V/5A Surge Immunity EN 61000-4-5 2 KV line to earth / 1 KV line to line A
REL-150-2005 +15V/5A -15V/5A Conducted Immunity EN 61000-4-6 0.15 to 80MHz, 10V, 80% AM A
REL-150-1001 2.5V/30A(21) Magnetic Field Immunity EN 61000-4-8 30A/m, 60 Hz. A
REL-150-1002 3.3V/30A(21) Voltage Dips EN 61000-4-11 0% UT, 0.5 cycles, 0-315° 100/240V A/A
REL-150-1003 5V/30A(21) 0% UT, 1 cycles, 0° 100/240V A/A
REL-150-1004 12V/12.5A 40% UT, 10/12 cycles, 0° 100/240V B/A
REL-150-1005 15V/10.0A 70% UT, 25/30 cycles, 0° 100/240V B/A
REL-150-1006 24V/6.3A Voltage Interruptions EN 61000-4-11 0% UT, 300 cycles, 0° 100/240V B/B
REL-150-1007 28V/5.4A Radiated Emissions EN 55011/32 Class B
REL-150-1008 48V/3.1A Conducted Emissions EN 55011/32 Class B
REL-150-1009 20-31V/5.4A Harmonic Current Emissions EN 61000-3-2 Class A
REL-150-1010 36V/4.16A Voltage Fluctuations/Flicker EN 61000-3-3 Compliant
ORDERING INFORMATION ORDERING INFORMATION
Consult factory for alternate output configurations. Please specify the following optional features when ordering:
Consult factory for positive, negative or floating outputs.
REL-150-4010: TUV only. CH - Chassis RE - Remote Inhibit
All specifications are maximum at 25°C/150W unless otherwise stated, may vary by model and CO - Cover I/O - Isolated Outputs
are subject to change without notice. TS - Terminal Strip

INTEGRATED
POWER DESIGNS 300 Stewart Road ■ Wilkes-Barre, PA 18706 ■ Phone: (570) 824-4666 ■ Fax: (570) 824-4843 ■ Email: [email protected] ■ Web: www.ipdpower.com
REL-150 SERIES MECHANICAL SPECIFICATIONS APPLICATIONS INFORMATION
1. Each output can deliver its rated current but Total Output Power must not exceed 150W,
as determined by the cooling method.
2. Generally, adequate cooling is provided when semiconductor case temperatures do not
exceed 70°C rise and transformer temperature does not exceed 60°C rise at any
specified ambient temperature.
3. Sufficient area must be provided around power supply to allow natural movement of air to
develop in convection-cooled applications.
4. This product is intended for use as a professionally-installed component within information
technology, industrial, and medical equipment and is not intended for stand-alone
operation.
5. A minimum load of 10% is required on Output 1 to ensure proper regulation of remaining
outputs.
6. This product includes only one fuse in the input circuit. In consideration of Clause 8.11.5
of IEC 60601-1:2005, a second fuse may be required in neutral conductor of the end
product.
7. Peak-to-Peak Output Ripple and Noise is measured directly at the output terminals of the
power supply, without the use of the probe ground lead or retractable tip (tip-and-barrel
method), 20 MHz bandwidth.
8. This product was type-tested and safety-certified using the dielectric strength test voltages
listed in Table 6 of IEC 60601-1:2005. In consideration of Clause 8.8.3, care must be
taken to insure that the voltage applied to a reinforced insulation does not overstress
different types and levels of insulation. Primary and secondary-to-ground capacitors may
need to be disconnected prior to performing a dielectric strength test on the power supply
or the end product. It is highly recommended that the DC test voltages listed in DVB.1,
Annex DVB of UL 60601-1 1st Edition are not exceeded during a production-line dielectric
strength test of the assembled end product. Please consult factory for further information.
9. This power supply has been safety-approved and final-tested using a DC dielectric
strength test. Please consult factory before performing an AC dielectric strength test.

10. Remote-Sense terminals may be used to compensate for cable losses up to 250mV. The
use of a twisted pair, decoupling capacitors and an appropriately-rated low-impedance
capacitor connected across the load will increase noise immunity.
11. Maximum screw penetration into bottom chassis mounting holes is 0.100 inches.
Maximum screw penetration into side chassis mounting holes is 0.250 inches.
12. To comply with emissions specifications, all four mounting hole pads must be electrically
connected to a common metal chassis. Chassis/Cover option is recommended. Refer to
Operating Instructions for additional information.
13. Common RF shielding precautions may need to be taken to assure emissions
compliance. Refer to Operating Instructions for additional information.
14. Power-Fail (AC-Good) feature provides a logic-low warning signal from an open collector
transistor output 10ms prior to loss of output from AC failure, 5V/10mA.
15. 300LFM minimum of airflow must be maintained one inch above all points of top-side
components or cover when forced-air cooling is required.
16. Total power must not exceed 100W with convection cooling or 150W with forced-air
cooling on open frame models except where noted.
17. Total power must not exceed 85W with convection cooling or 150W with forced-air cooling
and Chassis/Cover option.
18. Total current from Outputs 3 & 4 must not exceed 3A with convection cooling.
19. Total current from Outputs 1 & 2 must not exceed 15A with convection cooling.
20. Rated 12A maximum with convection cooling.
21. Rated 20A maximum with convection cooling.
MAXIMUM OUTPUT POWER vs. AMBIENT TEMPERATURE
150
140
130 F O R C E D A I R
Output Power (Watts)

120 C O O L I N G
110
100
C O N V E C T I O N C O O L I N G
90
80
70
60 CONVECT I O N
COOLI NG
50 WIT H CHASSI S/ C OV ER
40
30
20
10
0
0 10 20 30 40 50 60 70
Ambient Temperature (C)
CONNECTOR SPECIFICATIONS
P1 AC Input 0.156 friction lock header mates with Molex 09-50-3031 or equivalent
crimp terminal housing with Molex 2478 or equivalent crimp terminal.
P2 DC Output 6-32 screw down terminal mates with #6 ring tongue
 (Single) terminal. (10 in-lb max)
P2 DC Output 0.156 friction lock header mates with Molex 09-50-3141 or equivalent
(Multiple) crimp terminal housing with Molex 2478 or equivalent crimp terminal.
G Ground 0.187 quick disconnect terminal.
P3 Remote/P.F./ 0.100 friction lock header mates with Molex 50-57-9008or equivalent
Sense crimp terminal housing with Molex type 71851 or equivalent crimp
(Single) terminal.
REV. W 2/16/2021

P3 P.F./Sense 0.100 breakaway header mates with Molex 22-55-2061 or equivalent

(Multiple) crimp terminal housing with Molex type 70058 or equivalent crimp
terminal.
P4 Remote 0.100 breakaway header mates with Molex 50-57-9002 or equivalent
(Multiple) crimp terminal housing with Molex type 71851 or equivalent crimp
terminal.
INTEGRATED
POWER DESIGNS 300 Stewart Road ■ Wilkes-Barre, PA 18706 ■ Phone: (570) 824-4666 ■ Fax: (570) 824-4843 ■ Email: [email protected] ■ Web: www.ipdpower.com