STRUCTURE LABORATORY

LABORATORY WORKSHEET

Course Code BFC 31901

Department Civil Engineering

Force in a Statically Indeterminate Cantilever

Title
Truss
 Faculty : Faculty of Civil Engineering and Built
Page 1
Environment
Department : Department of Civil Engineering Edition 1
Checking No
Title : Force in a Statically Indeterminate Effective Date
Cantilever Truss Amendment Date

1.0 OBJECTIVE

1.1 To observe the effect of redundant member in structure and to understand the
method of analysing a statically indeterminate cantilever truss

2.0 LEARNING OUTCOME

2.1 To apply the engineering knowledge in practical application

2.2 To enhance technical competency in structural engineering through laboratory
application

3.0 THEORY

• In a statically indeterminate truss, static equilibrium alone cannot be used to

calculate member force. If we were to try, we would find that there would be too
many “unknowns” and we will not be able to solve the calculations
• Instead, we will use a method known as the flexibility method, which uses an idea
known as strain energy
• The mathematical approach to the flexibility method will be found in most
structural text books

Figure 1: Idealized Statically Indetermined Cantilever Truss

 Faculty : Faculty of Civil Engineering and Built
Page 2
Environment
Department : Department of Civil Engineering Edition
Checking No
Title : Force in a Statically Indeterminate Effective Date
Cantilever Truss Amendment Date

• Basically, the flexibility method uses the idea that energy stored in the frame
would be the same for a given load whether the frame is redundant or not
• In other word, the external energy = internal energy
• In practice, the loads in the frame are calculated in its “released” form (that is,
without the redundant member) and then calculated with a unit load in place of
the redundant member and remaining members.
• The load for redundant member is given by:
•
𝑓𝑓𝑓𝑓𝑓𝑓
𝑃𝑃 = − ∑
𝑛𝑛2 𝑙𝑙

• The remaining member force are then given by :

𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀𝑀 𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓 = 𝑃𝑃𝑃𝑃 + 𝑓𝑓

where,
𝑃𝑃 = 𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙 𝑜𝑜𝑜𝑜 𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟 𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚 (𝑁𝑁)
𝑙𝑙 = 𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙ℎ 𝑜𝑜𝑜𝑜 𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚
𝑛𝑛 = 𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙 𝑖𝑖𝑖𝑖 𝑒𝑒𝑒𝑒𝑒𝑒ℎ 𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚 𝑑𝑑𝑑𝑑𝑑𝑑 𝑡𝑡𝑡𝑡 𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙 𝑖𝑖𝑖𝑖 𝑝𝑝𝑝𝑝𝑝𝑝𝑝𝑝𝑝𝑝 𝑜𝑜𝑜𝑜
𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟 𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚 (𝑁𝑁)
𝐹𝐹 = 𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓 𝑖𝑖𝑖𝑖 𝑒𝑒𝑒𝑒𝑒𝑒ℎ 𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚 𝑤𝑤ℎ𝑒𝑒𝑒𝑒 𝑡𝑡ℎ𝑒𝑒 𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓𝑓 𝑖𝑖𝑖𝑖 released (𝑁𝑁)

• Figure 2 shows the force in the frame due to the load of 250 N. You should be
able to calculate these values from Experiment titled: Force in a Statically
Determinate truss

Figure 2: Force in the “ Released” Truss

 Faculty : Faculty of Civil Engineering and Built
Page 3
Environment
Department : Department of Civil Engineering Edition
Checking No
Title : Force in a statically Indeterminate Effective Date
Cantilever Truss Amendment Date

• Figure 3 shows the loads in the member due to the unit load being applied to the
frame.
• The redundant member is removed from the truss so it became statically
determinate truss as shown Figure 2.

Figure 3: Forces in the truss due to unit load imposed on the redundant member

3.0 PROCEDURE

1.0 Wind the thumbwheel on the ‘redundant’ member up to the boss and hand tighten it. Do
not use any tools to tighten the thumbwheel.
2.0 Apply the pre-load of 100N downward, re- zero the load cell and carefully zero the
digital indicator.
3.0 Carefully apply a load 250N and check the frame is stable and secure.
4.0 Return the load zero (leaving the 100N Preload). Recheck and re-zero the digital
indicator. Never apply loads greater than those specified on the equipment.
5.0 Apply loads in the increment shown in Table1, record the strain readings and the digital
indicator readings.
6.0 Subtract the initial (zero) strain reading (be careful with your signs) and complete Table
2.
7.0 Calculate the equipment members’ force at 250N and fill them into Table 3.
8.0 Plot a graph of Load vs Deflection from Table 1 on the same axis as Load vs Deflection
when the redundant ‘removed’.
9.0 The calculation for redundant truss is made much simpler and easier if the tabular
method is used to sum up all of the “Fnl” and “n2l” as shown in Table 4.
 Faculty : Faculty of Civil Engineering and Built
Page 4
Environment
Department : Department of Civil Engineering Edition
Checking No
Title Force in a statically Indeterminate Effective Date
Amendment Date
cantilever Truss

10. Refer to Table 4 and fill in all the values required for all the terms.
11. Fill in Table 3 based on calculated value in Table 4.

4.0 RESULT
Table 1: Strain Reading and Frame
Load Strain Reading Digital
(N) indicator
1 2 3 4 5 6 7 8
reading(mm)
0
50
100
150
200
250

Table 2 : True Strain Reading

Load Strain Reading
(N) 1 2 3 4 5 6 7 8
0
50
100
150
200
250
 Faculty : Faculty of Civil Engineering and Built
Page 5
Environment
Department : Department of Civil Engineering Edition
Checking No
Title : Force in a Statically Indeterminate Effective Date
Cantilever Truss Amendment Date

Table 3 : Measured and Theoretical Forces

Experimental Force Theoretical Force
Member (N) (N)

1
2
3
4
5
6
7
8

Table 4 : Table for calculating the forces in the Redundant Truss

Member Length
𝒇𝒇 𝒏𝒏 𝒇𝒇𝒇𝒇𝒇𝒇 𝒏𝒏𝟐𝟐 𝒍𝒍 𝑷𝑷𝑷𝑷 𝑷𝑷𝑷𝑷 + 𝒇𝒇
1
2
3
4
5
6
7
8

Total

𝑓𝑓𝑓𝑓𝑓𝑓
𝑃𝑃 = − ∑
𝑛𝑛2 𝑙𝑙
 Faculty : Faculty of Civil Engineering and Built
Page 6
Environment
Department : Department of Civil Engineering Edition
Checking No
Title : Force in a Statically Indeterminate Effective Date
Cantilever Truss Amendment Date

Using the Young’ s Modulus relationship, calculate the equivalent member force. Complete the
experimental force in Table 3 (ignore member 6 at this stage).

5.0 DISCUSSION AND CONCLUSION

1.0 From Table 3, compare your answer to the experimental values, comment on the
accuracy of your result.
2.0 Compare all of the member forces and the deflection to those from statically
determinate frame. Comment on them in term of economy and safety of the
structure.
3.0 What problems could you foreseen if you were to use a redundant frame in a ‘real
life’ application (Hint: Look at the zero values for the strain reading once you have
included redundant member by winding up thumbnut)