S7L1D-G4 Wdg.

312 - Technical Data Sheet

Standards
STAMFORD industrial alternators meet the requirements of the relevant parts of the IEC EN 60034 and the relevant
section of other international standards such as BS5000, VDE 0530, NEMA MG1-32, IEC34, CSA C22.2-100 and
AS1359. Other standards and certifications can be considered on request.

Quality Assurance

Alternators are manufactured using production procedures having a quality assurance level to BS EN ISO 9001.

Excitation and Voltage Regulators

Excitation System
AVR Type MX341 MX322 DECS150
Voltage Regulation ± 1% ± 0.5% ± 0.25% with 4% Engine Governing
AVR Power PMG PMG PMG

No Load Excitation Voltage (V) 15.4 - 14.7

No Load Excitation Current (A) 0.67 - 0.62
Full Load Excitation Voltage (V) 73
Full Load Excitation Current (A) 2.9
Exciter Time Constant (seconds) 0.125

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

Electrical Data
Insulation System H
Stator Winding Double Layer Concentric
Winding Pitch 2/3
Winding Leads 6
Winding Number 312
Number of Poles 4
IP Rating IP23

RFI Suppression BS EN 61000-6-2 & BS EN 61000-6-4,VDE 0875G, VDE 0875N.

Refer to factory for others
Waveform Distortion NO LOAD < 1.5% NON-DISTORTING BALANCED LINEAR LOAD < 5.0%
Short Circuit Ratio 1/Xd
Steady State X/R Ratio 33.26
50 Hz 60 Hz
Telephone Interference THF<2% TIF<50
Cooling Air Flow 2.39 m³/sec 2.87 m³/sec
Voltage Star (V) 380 400 415 440 416 440 460 480
Voltage Parallel Star (V) - - - - - - - -
Voltage Delta (V) - - - - - - - -

kVA Base Rating (Class H) for

2020 2080 2080 2040 2350 2500 2550 2600
Reactance Values (kVA)

Saturated Values in Per Unit at Base Ratings and Voltages

Xd Dir. Axis Synchronous 2.56 2.38 2.21 1.93 2.98 2.84 2.65 2.48
X'd Dir. Axis Transient 0.18 0.17 0.16 0.14 0.21 0.20 0.19 0.18
X''d Dir. Axis Subtransient 0.13 0.12 0.11 0.09 0.15 0.14 0.13 0.12
Xq Quad. Axis Reactance 1.93 1.79 1.66 1.45 2.24 2.13 1.99 1.86
X''q Quad. Axis Subtransient 0.22 0.20 0.19 0.16 0.25 0.24 0.23 0.21
XL Stator Leakage Reactance 0.08 0.07 0.07 0.06 0.09 0.09 0.08 0.08
X2 Negative Sequence Reactance 0.16 0.15 0.14 0.12 0.19 0.18 0.16 0.15
X0 Zero Sequence Reactance 0.03 0.03 0.03 0.03 0.04 0.04 0.04 0.03
Unsaturated Values in Per Unit at Base Ratings and Voltages
Xd Dir. Axis Synchronous 3.07 2.86 2.65 2.31 3.58 3.40 3.18 2.98
X'd Dir. Axis Transient 0.21 0.19 0.18 0.16 0.24 0.23 0.22 0.20
X''d Dir. Axis Subtransient 0.15 0.14 0.13 0.11 0.17 0.16 0.15 0.14
Xq Quad. Axis Reactance 1.98 1.84 1.71 1.49 2.31 2.20 2.05 1.92
X''q Quad. Axis Subtransient 0.26 0.24 0.23 0.20 0.31 0.29 0.27 0.25
XL Stator Leakage Reactance 0.09 0.08 0.08 0.07 0.10 0.10 0.09 0.09
Xlr Rotor Leakage Reactance 0.20 0.19 0.17 0.15 0.24 0.22 0.21 0.20
X2 Negative Sequence Reactance 0.19 0.18 0.16 0.14 0.22 0.21 0.20 0.18
X0 Zero Sequence Reactance 0.04 0.04 0.03 0.03 0.05 0.04 0.04 0.04

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

Time Constants (Seconds)

T’d Transient Time Const. 0.15
T’’d Sub-Transient Time Const. 0.0150
T’do O.C. Field Time Const. 4.49
Ta Armature Time Const. 0.0284
T’’q Sub-Transient Time Const. 0.0104
0
Resistances in Ohms (Ω) at 22 C
Stator Winding Resistance (Ra),
0.0007
per phase for series connected
Rotor Winding Resistance (Rf) 2.15
Exciter Stator Winding Resistance 22.3
Exciter Rotor Winding Resistance per
0.065
phase
PMG Phase Resistance (Rpmg) per
1.91
phase
Positive Sequence Resistance (R1) 0.0009
Negative Sequence Resistance (R2) 0.0010
Zero Sequence Resistance (R0) 0.0009
Saturation Factors 400V 480V
SG1.0 0.283 0.275
SG1.2 1.366 1.201
Mechanical Data
Shaft and Keys
All alternator rotors are dynamically balanced to better than BS6861: Part 1 Grade 2.5 for
minimum vibration in operation. Two bearing generators are balanced with a half key.

1 Bearing 2 Bearing
SAE Adaptor SAE 0, 00 SAE 0, 00
Moment of Inertia 45.47 kgm² 44.44 kgm²
Weight Wound Stator 1725kg 1725kg
Weight Wound Rotor 1488kg 1445kg
Weight Complete Alternator 3637kg 3604kg
Shipping weight in a Crate 3689kg 3656kg
Packing Crate Size 220 x 105 x 155 (cm) 220 x 105 x 155 (cm)
Maximum Over Speed 2250 RPM for two minutes
Bearing Drive End - BALL. 6232
Bearing Non-Drive End BALL. 6319 BALL. 6319

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

THREE PHASE EFFICIENCY CURVES

50Hz 60Hz

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

Locked Rotor Motor Starting Curves - Separately Excited

50Hz

60Hz

Transient Voltage Dip Scaling Factor Transient Voltage Rise Scaling Factor
PF Factor
< 0.5 1 For voltage rise multiply voltage dip by 1.25
0.5 0.97
0.6 0.93
0.7 0.9
0.8 0.85
0.9 0.83

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

Three-phase Short Circuit Decrement Curve - Separately Excited

50Hz

Sustained Short Circuit = 7182 Amps

60Hz

Sustained Short Circuit = 8495 Amps

Note 1 Note 3
The following multiplication factors should be The following multiplication factor should be used to convert the
used to adjust the values from curve between values calculated in accordance with NOTE 1 to those
time 0.001 seconds and the minimum current applicable to the various types of short circuit :
point in respect of nominal operating voltage :

50Hz 60Hz 3-phase 2-phase L-L 1-phase L-N

Voltage Factor Voltage Factor Instantaneous x 1.00 x 0.87 x 1.30
380V X 1.00 416V X 1.00 Minimum x 1.00 x 1.80 x 3.20
400V X 1.05 440V X 1.06 Sustained x 1.00 x 1.50 x 2.50
415V X 1.09 460V X 1.10 Max. sustained duration 10 sec. 5 sec. 2 sec.
440V X 1.16 480V X 1.15 All other times are unchanged
Note 4
The sustained current value is constant irrespective of Curves are drawn for Star connected machines under no-load
voltage level excitation at rated speeds. For other connection (where
Note 2 applicable) the following multipliers should be applied to
The sustained current values are for MX341 current values as shown :
AVR. For MX322 and Digital AVR 1.2 factor to Parallel Star = Curve current value X 2
be applied to the sustained short circuit Series Delta = Curve current value X 1.732

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

Typical Alternator Operating Charts

400V/50Hz

480V/60Hz

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
 S7L1D-G4 Wdg.312

RATINGS AT 0.8 POWER FACTOR

Class - Temp Rise Standby - 163/27°C Standby - 150/40°C Cont. H - 125/40°C Cont. F - 105/40°C
Star (V) 380 400 415 440 380 400 415 440 380 400 415 440 380 400 415 440
50 Parallel Star (V) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
Delta (V) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
Hz
kVA 2165 2250 2250 2185 2105 2170 2170 2125 2020 2080 2080 2040 1880 1935 1935 1900
kW 1732 1800 1800 1748 1684 1736 1736 1700 1616 1664 1664 1632 1504 1548 1548 1520
Efficiency (%) 95.8 95.8 95.9 96.1 95.9 95.9 96.0 96.1 96.0 96.0 96.1 96.2 96.1 96.1 96.2 96.2
kW Input 1808 1878 1877 1820 1757 1810 1809 1769 1684 1733 1732 1697 1565 1610 1610 1579

Star (V) 416 440 460 480 416 440 460 480 416 440 460 480 416 440 460 480
60 Parallel Star (V) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Hz Delta (V) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
kVA 2506 2675 2731 2787 2437 2600 2650 2706 2350 2500 2550 2600 2194 2325 2375 2425
kW 2005 2140 2185 2230 1950 2080 2120 2165 1880 2000 2040 2080 1755 1860 1900 1940
Efficiency (%) 95.8 95.8 95.9 96.0 95.9 95.9 96.0 96.0 96.0 96.0 96.1 96.1 96.1 96.1 96.2 96.2
kW Input 2092 2233 2278 2323 2033 2169 2209 2254 1959 2084 2124 2164 1827 1936 1976 2017

De-Rates
All values tabulated above are subject to the following reductions:
- 5% when air inlet filters are fitted
- 3% for every 500 meters by which the operating altitude exceeds 1000 meters above mean sea level
- 3% for every 5°C by which the operational ambient temperature exceeds 40°C @ Class H temperature rise
(please refer to applications for ambient temperature de-rates at other temperature rise classes)
- For any other operating conditions impacting the cooling circuit please refer to applications
Note: Requirement for operating in an ambient exceeding 60°C and altitude exceeding 4000 meters (for <690V) or
1500 meters (for >690V) must be referred to applications.

Dimensional and Torsional Drawing

For dimensional and torsional information please refer to the alternator General Arrangement and rotor drawings
available on our website (http://stamford-avk.com/)

Note: Continuous development of our products means that the information contained in our data sheets
can change without notice, and specifications should always be confirmed with Cummins Generator
Technologies prior to purchase.

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019
Follow us @stamfordavk

Cummins Generator Technologies

View our videos at youtube.com/stamfordavk

news.stamford-avk.com

For Applications Support:

[email protected]

For Customer Service:

[email protected]

For General Enquiries:

[email protected]

Copyright 2016. Cummins Generator Technologies Ltd. All rights reserved.

Cummins and the Cummins logo are registered trade marks of Cummins Inc.
STAMFORD is a registered trade mark of Cummins Generator Technologies Ltd.

Page 1 S7L1D-G4_Wdg.312_A062L872_Rev.B_22.08.2019