COMPETENCY-BASED LEARNING MATERIALS

Sector : Electronics

Qualification Title : Computer Systems Servicing NC II

Unit of Competency : Set-up Computer Networks

Module Title : Setting up Computer Networks

IBA College of Mindanao

 HOW TO USE THIS COMPETENCY-BASED LEARNING
MATERIALS

Welcome!
The unit of competency, “Setting up Computer Networks“, is one of
the competencies of COMPUTER SYSTEMS SERVICING NC II, a course
which comprises knowledge, skills and attitudes required for a TESDA
trainee to possess.
In this module, you are required to go through a series of learning
activities in order to complete each learning outcome. In each learning
outcome are Information Sheets, Self-Checks, Operation Sheets and
Task/Job Sheets. Follow and perform the activities on your own. If you
have questions, do not hesitate to ask for assistance from your facilitator.
Remember to:
 Work through all the information and complete the activities in
each section.
 Read information sheets and complete the self-check. Suggested
references are included to supplement the materials provided in
this module.
 Most problably, your trainer will also be your supervisor or
manager. He is there to support you and show you the correct
way to do things.
 You will be given plenty of opportunities to ask questions and
practice on the job. Make sure you practice your new skills
during regular work shifts. This way, you will improve your
speed, memory and your confidence.
 Use Self-Checks, Operations Sheet or Task or Job Sheets at the
end of each section to test your own progress. Use the
Performance Criteria Checklist or Procedural Checklist located
after the sheet to check your own performance.
 When you feel confident that you have sufficient practice, ask
your trainer to evaluate you. The results of your assessment will
be recorded in your Achievement Chart and Progress Chart.

You need to complete this module before you can perform the next
module.

Document No.
CBLMs on Date Developed:
COMPUTER SYSTEMS August 1, 2018 Issued by:
SERVICING NCII Page 2 of 24
Developed by:
Setting up Computer
Networks JOEL T. BUCAR Revision # 00
 COMPUTER SYSTEMS SERVICING NC II

List of Competencies

No. Unit of Competency Module Title Code

Installing and
Install and Configure
1. Configuring ELC724331
Computer Systems
Computer Systems
Setting Up
Set-Up Computer Networks ELC724332
2. Computer
Networks
Setting Up Computer
Set-Up Computer Servers ELC724333
3. Servers

Maintaining and
Maintain and Repair
Repairing Computer
Computer Systems and ELC724334
4. Systems and
Networks
Networks
 MODULE CONTENT

Qualification Title : Computer Systems Servicing NC

II Unit of Competency : Set-up Computer Network
Module Title : Setting up Computer Networks

Introduction:
This unit covers the outcomes required in setting-up computers
networks for LANs and small-office home-office (SOHO) systems. It consists
of competencies to install network cables, set network configuration, set
router/Wi-Fi/ wireless access point/repeater configuration as well as to
inspect and test the configured computer networks.
Learning Outcomes:
At the end of this module you will be able to :
1. Install Network cables
2. Set network configuration
3. Set router /WI-FI / wireless access point /
repeater configuration
4. Inspect and test the configured computer networks

ASSESSMENT CRITERIA:
1.1 Cable routes are determined and planned in accordance
with network design and actual installation site.
1.2 Network materials necessary to complete the work are
identified and obtained in accordance with established
procedures and checked against systems requirements
1.3 Tools, equipment and testing devices needed to carry out the
installation work are obtained in accordance with
established procedures and checked for correct operation
and safety
1.4 Appropriate personal protective equipment is used and
OHS policies and procedures are followed
1.5 Copper cable splicing is performed based on Electronic
Industries Alliance/Telecommunications Industry Association
(EIA/TIA) standards
1.6 Network cables and cable raceway are installed in accordance
with established procedures and installation requirements
1.7 Installation work is performed and is checked to ensure
no unnecessary damage has occurred and complies with
requirements
1.8 OHS standards and 5S principles are followed according
to enterprise requirements
1.9 Excess components and materials are disposed of based on WEEE
directives and 3Rs waste management program.
2.1 Network connectivity of each terminal is checked in accordance
with network design.
2.2 Any fault or problem in the network system is diagnosed and
remedied in line with the standard operating procedures.
2.3 Network interface card (NIC) settings are configured in accordance
with network design.
2.4 Communication checking between terminals are carried out in
accordance with OS network configuration guides
2.5 Unplanned events or conditions are responded to in accordance
with established procedures
3.1 Client Device systems settings are configured in accordance with
manufacturers’ instructions and end-user preferences
3.2 Local area network (LAN) port is configured in accordance with
manufacturers’ instructions and network design
3.3 Wide area network (WAN) port is configured in accordance with
manufacturers’ instructions and network design
3.4 Wireless settings are configured in accordance manufacturers’
instructions, network design and end-user preferences
3.5 Security/Firewall/Advance settings are configured in accordance
with manufacturers’ instructions and end-user preferences
4.1 Final inspections are undertaken to ensure that the configuration
done on the computer networks conforms with the manufacturer’s
instruction/manual
4.2 Computer networks are checked to ensure safe operation.
4.3 Reports are prepared/completed according to company
requirements.