TD-25M

CRAWLER DOZER

Net Horsepower
238 kW (320 hp)
Blade Capacity
up to 21 m3 (27.5 yd3)
Operating Weight
36 210 kg (79,829 lb)
 TD-25M
CRAWLER DOZER
■ Comfortable, sound suppressed cab
■ Large capacity blades
■ Heavy duty undercarriage
■ Joystick for transmission
and steering module control

ENGINE STEERING AND BRAKING

*Make and Model . . . . . . . . . . . . . . . . . . . . . . . . . . CUMMINS QSX-15 Two-speed geared steering module provides gradual turns while
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-cycle diesel, turbocharged maintaining full power to both tracks plus conventional clutch-brake
CAC, direct start, direct injection performance for tight or pivot turns.
** Gross Horsepower @ 2100 rpm . . . . . . . . . . . . . . . . 268 kW (360 hp) Foot pedal applies both brakes for parking and downhill control.
*** Net Flywheel power @ 2100 rpm . . . . . . . . . . . . . . . 238 kW (320 hp)
Brakes are spring applied and hydraulically released.
Maximum torque @ 1400 rpm . . . . . . . . . . . . . . 1647 Nm (1,215 lb ft)
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 l (912 in3) FINAL DRIVES
Bore and Stroke . . . . . . . . . . . . . . . . . . . 137 x 169 mm (5.4” x 6.65”) Double-reduction with planetary final drive stage provides desired gear
Lubrication, full flow filtering w/bypass . . . . . . . . . . . . . . . full pressure reduction at the sprocket. Eight-piece bolt-on sprocket distributes wear
Number of Main Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
evenly over track bushings letting every tooth ride free one-half of the
Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 V
Air cleaner . . . . . . . . . . . . . . . dry type with exhaust aspirated primary time to reduce wear. Sprocket segments are replaceable without removing
and safety elements and service indicator track frames.

* Meets EU Stage II and EPA Tier 2 emission regulations TRACK FRAME

**Output of complete engine operating under SAE J1995 conditions
*** Output of standard engine complete with fan, air cleaner, muffler, alternator All-welded heavy box section track frame is kept in alignment with track
(not charging), water pump, lubricating oil pump, and fuel pump, per SAE J1349. frame guides providing true vertical oscilation.

TRANSMISSION & TORQUE CONVERTER Track rollers each side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Modular countershaft type power shift provides ”on the move” speed Top idlers each side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
and directional changes. Front idlers (drum type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Single stage, single phase 409 mm (16”) modular torque converter All rollers and idlers . . . . . . . . . . . . . . . . . . . . . . . . lifespan lubricated
with a stall ratio of 2.45:1. The three speed transmission combined with Oscillation at center of front idler . . . . . . . . . . . . . . . . . . 406 mm (16”)
exclusive two speed steering provides 6 speeds forward and 6 reverse.
The joystick valve has electric transmission range shift control for up
and down shifting, steering Hi/Lo selection and LH/RH gradual turn.
TRACKS
Lubricated Track System (LTS) virtually eliminates internal pin and
TRAVEL SPEEDS bushing wear through use of a patented seal assembly.
The split master link reduces chain removal and installation time.
Gear Range Forward Reverse
km/h (mph) km/h (mph)
1 st Low 3.1 (1.94) 3.8 (2.34) Track shoe width, standard . . . . . . . . . . . . . . . . . . . . . . 559 mm (22”)
High 4.0 (2.52) 4.9 (3.03) Strutted track link pitch . . . . . . . . . . . . . . . . . . . . . . . . 250 mm (9.86”)
2 nd Low 5.2 (3.25) 6.3 (3.92) Track shoes, each side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
High 6.8 (4.20) 8.1 (5.05) Ground contact area with std. shoes . . . . . . . . . . . . 3.5 m2 (5,456 in2)
3 rd Low 8.3 (5.15) 9.9 (6.15) Ground pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 14.6 psi (100 kPa)
High 10.6 (6.56) 12.7 (7.90)
Height of grouser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 mm (3”)
90 200 Track adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . full hydraulic
190 Ground clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mm (19.6”)
180 POWER SHIFT
80 DRAWBAR PULL vs. SPEED Fixed drawbar – height from ground to
170
centerline of 95 mm (3.75”) clevis . . . . . . . . . . . . . . . . 537 mm (21.1”)
160
70 1st LOW
150

140
REFILL CAPACITIES
60 130 1st HIGH Liter (US gal)
DRAWBAR PULL x 1000 lb

120 Fuel tank 825 (218)

50 110 Cooling system 62 (16.4)
100
Crankcase 49 (13)
kg x 1000

2nd LOW
90
40 Transmission system 240 (63)
80
2nd HIGH Final drive, each side 64 (16.9)
70
30
3rd LOW
60

50
3rd HIGH WEIGHT (Operating)
20
40 Includes std. equipment and Semi-U blade . . . 36 210 kg (79,829 lb)
30
10 20

10

1 2 3 4 5 6 7 mph

2 4 6 8 10 km/h
 3.93 m (12'11")
3.80 m (12'6")
3.67 m (12')

TD-25M

3.15 m (10'4") 2.14 m (7'0")

5.07 m (16'7") 2.70 m (8'10")

VERTICAL DIMENSIONS INCLUDE 76 mm (3”) GROUSER HEIGHT

OVERALL DIMENSIONS WITH EQUIPMENT

BLADE SELECTION SEMI-U FULL-U ANGLE COAL Blade
Length with blade and drawbar 6.81 m (22’4”) 7.08 m (23’3”) 6.82 m (22’5”) 7.46 m (24’6”)
Length with blade and multi-shank ripper 8.34 m (27’4”) 8.61 m (28’3”) 8.35 m (27’5”) 8.99 m (29’6”)
Length with blade and single shank ripper 8.94 m (29’4”) 9.21 m (30’3”) 8.95 m (29’4”) –
Width, blade angled – – 4.59 m (15’1”) –
Width over trunnions 3.20 m (10’5”) 3.20 m (10’5”) 3.20 m (10’5”) 3.20 m (10’5”)
Width over “C” frame – – 3.52 m (11’7”) –

BLADE SPECIFICATIONS
BLADE SELECTION SEMI-U FULL-U ANGLE COAL Blade
Blade Capacity, SAE J1265 9.6 m3 (12.5 yd3) 11.5 m3 (15.0 yd3) 5.7 m3 (7.4 yd3) 21 m3 (27.5 yd3)
Max. Usable Track Shoe Width 711 mm (28”) 711 mm (28”) 711 mm (28”) 711 mm (28”)
Blade Dimensions: – width over end bits 4.05 m (13’3”) 4.35 m (14’3”) 4.95 m (16’3”) 5.61 m (18’5”)
– height, struts centered A 1.76 m (5’9”) 1.76 m (5’9”) 1.26 m (4’1”) 2.10 m (6’11”)
Max. lift: – straight B 1.27 m (4’2”) 1.27 m (4’2”) 1.37 m (4’6”) 1.27 m (4’2”)
– angled – – 1.54 m (5’1”) –
Max. drop below ground level C 600 mm (23.6”) 600 mm (23.6”) 660 mm (26”) 600 mm (23.6”)
Max. tilt adjustment D 880 mm (34.6”) 945 mm (37.2”) 435 mm (17.1”) 1220 mm (48”)
Blade angle, either side – – 25° –
Max. pitch adjustment E 10° 10° – 10°
Weight of blade equipment 5 640 kg (12,434 lb) 6 280 kg (13,845 lb) 5 460 kg (12,037 lb) 7 720 kg (17,020 lb)

RIPPER SPECIFICATIONS
SINGLE SHANK
RIPPER SELECTION MULTI-SHANK
Standard Deep
Tool Beam
Overall width 2 464 mm (97”) 1 245 mm (49”) 1 245 mm (49”)
Cross section (height x width) 381 x 478 mm (15” x 18.8”) 550 x 400 mm (21.7” x 15.7”) 550 x 400 mm (21.7” x 15.7”)
Ground clearance under tool beam: - ripper raised 1 544 mm (68”) 1 565 mm (62”) 1 565 mm (62”)
- ripper lowered 171 mm (6.7”) 154 mm (6.1”) 154 mm (6.1”)
Shank
Number of shank per ripper, max. 3 1 1
Spacing center to center 1 067 mm (42”) – –
Penetration, max. 760 mm (29.9”) 1 250 mm (49.2”) 1 700 mm (66.9”)
Ground clearance, max. raised 868 mm (34.2”) 770 mm (30.3”) 760 mm (29.9”)
Shank positions (vertical) 2 4 6
Weight
Complete, including one shank 5 100 kg (11,270 lb) 5 280 kg (11,630 lb) 5 370 kg (11,840 lb)
Each additional shank 318 kg (700 lb) – –
Penetration Force 137 kN (30,900 lb) 137 kN (30,900 lb) 137 kN (30,900 lb)
Pryout Force 317 kN (71,200 lb) 317 kN (71,200 lb) 317 kN (71,200 lb)
TD-25M
CRAWLER DOZER

HYDRAULIC CONTROL SYSTEM

Hydraulic pumps, driven from torque converter. Cylinders, bore and stroke:
Output @ 15.5 MPa (2250 psi) blade lift .......................................................... 127 x 1460 mm (5.0” x 57.5”)
& 2145 engine rpm ................................................ 313.2 l/min (82.7 gal/min)
tilt ........................................................................ 200 x 130 mm (7.9” x 5.1”)
Relief valve setting
blade lift & ripper .......................................................... 17.2 MPa (2,500 psi) tilt/pitch ................................................ 185/200 x 130 mm (7.3”/7.9” x 5.1”)

tilt .................................................................................. 18.4 MPa (2,670 psi) Reservoir with sight gauge, right fender mounted ...................... 130 l (34 gal)

STANDARD EQUIPMENT
• Air cleaner, dry type, with exhaust aspirated primary and safety • Horn, electric
elements and service indicator • Hydraulic control, 1 valve, 1 lever with pilot operated blade control (lift)
• Air conditioner/heater/pressurizer/defroster; A/C condenser, behind roof mounted • Instrument panel light
• Alarm, back-up • Instruments: Gauges: fuel level, engine coolant temperature, engine oil pressure,
• Alternator, 50A torque converter oil temp.,voltmeter, hourmeter, joystick control diplay; Warning
• Antifreeze, -37°C (-34°F) lights: air cleaner filter, transmission oil filter, hydraulic oil filter, transmission/clutch
• Batteries, (4) 12 V, 1920 CCA, maintenance free, cold start oil low pressure; Audible & visual warning system: low engine coolant level, low
• Brakes, parking, with lock
• Coolant filter conditioner engine oil pressure
• Cab with 2 post ROPS, seat belt (SAE J386), sound suppression, air recirculation • Lights w/guards, 2 front - lift cylinders mounted, 2 rear - fuel tank mounted
system, 2 front & 2 rear lights, 4 wipers w/washers, dome light, inside mirror • Muffler, under engine hood, insulated
(approved according to ROPS - SAE J1040 and FOPS - SAE J231) • Radiator guard doors, louvered, two-piece, hinged
• Cooling module, includes radiator, transmission oil cooler, • Receptacle, charging
fuel cooler, hydraulic oil/fan drive oil cooler, charge air cooler; • Seat, deluxe, suspension type, fabric cover, adjustable with arm rests,
isolation mounted swivel 15° to right
• Cylinders, lift, with quick drop valve • Starting, 24 V
• Decelerator - right and brake - center, foot operated • Steering, 2 speed, left hand single lever control (joystick)
• Diagnostic centers for power train and equipment hydraulic pressures • Tools compartment
• Drawbar, fixed • Torque converter, single stage
• Ecological drains for engine oil, radiator coolant and hydraulic oil • Track adjusters, hydraulic
• Engine hood, solid, sloped • Track chain, sealed and lubricated (LTS) with split master link, 38 links
• Exhaust, resonator with elbow
• Fan, hydraulic driven, suction type, 2-speed • Track chain guides, integral
• Filters, engine oil, full flow and by-pass with replaceable “spin-on” elements • Track frame, 7 roller, 2.14 m (84”) gauge, oscillating type,
• Filters, power train & equipment hydraulics, “spin-on” micro glass type lifespan lubricated rollers and idlers
• Final drive seal • Track shoes 559 mm (22”), grouser type
• Fuel strainer • Transmission, power shift, 3 speeds forward, 3 reverse, combined
• Guards: crankcase with front pull hook, fan, radiator, dirt deflector sprocket, with 2 speed steering provides 6 speeds forward and 6 reverse
transmission • Water separator, fuel system

OPTIONAL ATTACHMENTS
• Air recirculation system with MSHA external filter • Lights, 2 front and 2 rear (for use w/canopy ROPS / FOPS)
• Alternator, 80 A • Lights, 2 front, ROPS mounted (for use with cab)
• AM/FM CD radio (for use with cab) • Mirrors, 2 pcs, exterior (for use w/cab)
• Bulldozer: • Operator platform covers (for use w/canopy ROPS/FOPS)
– Semi-U, w/tilt or tilt / pitch, 9.6 m3 (12.5 yd3) • Ripper, multi-shank w/hydraulic pitch
– Full-U, w/tilt or tilt / pitch, 11.5 m3 (15 yd3) – ripper shanks w/pin, max. 3
– Coal Dozer, w/tilt or tilt / pitch, 21 m3 (27.5 yd3) • Ripper, single-shank w/hydraulic pitch
– Angle Dozer, less tilt, 5.7 m3 (7.4 yd3) – ripper shank, standard dig
– Hydraulic tilt for Angle Dozer – ripper shank, deep dig
• Canopy, ROPS / FOPS (SAE J1040, J231) – pin puller, hydraulic
• Drawbar, fixed counterweight, 1860 kg (4100 lbs) • Sealed track system
• Drawbar, counterweight, 1860 kg (4100 lbs) • Seat, suspension, adjustable type, vinyl cover
(for use w/canopy ROPS / FOPS)
with additional counterweight (cast), 1452 kg (3200 lbs)
• Sound suppression package
• Engine enclosures: • Starting/charging receptacle plug assembly w/15 ft cable
– Solid hood and perforated side doors • Tools, inches, 17 items in metal box
– Hood and side doors perforated • Track shoes:
• Ether start 559 mm (22”) severe service
• Guards: 610 mm (24”)
– Crankcase, severe service 610 mm (24”) severe service
– Transmission, severe service 660 mm (26”) clipped corner
– Rock deflector sprocket 660 mm (26”) severe service, clipped corner
– Track roller, full length 711 mm (28”) clipped corner
• Heater/pressurizer/defroster 711 mm (28”)
• Hydraulic controls, 3-spool valve, 2 lever • Vandalism protection

Specifications subject to change without notice. Illustrations and pictures may include optional equipment and may not include all standard equipment.

MS-3086-DSS3 July 2005 © 2005 Marketing Services, Dressta Co. Ltd.