Scribd
Upload
999 views

Spec Sheet - Flare Stack Design

This document is a flare stack design specification sheet for a customer. It requests information about the equipment requirements, design parameters, pilot and ignition system for a flare stack. The equipment requirements section asks whether a utility or smokeless flare is needed and how it will be supported. The design parameters section requests information about flow rates, pressures, temperatures and regulations. It also requests a fuel and waste gas analysis. The pilot and ignition system section inquires about the type of pilot and power sources available on site.

Uploaded by

Scylar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
999 views

Spec Sheet - Flare Stack Design

This document is a flare stack design specification sheet for a customer. It requests information about the equipment requirements, design parameters, pilot and ignition system for a flare stack. The equipment requirements section asks whether a utility or smokeless flare is needed and how it will be supported. The design parameters section requests information about flow rates, pressures, temperatures and regulations. It also requests a fuel and waste gas analysis. The pilot and ignition system section inquires about the type of pilot and power sources available on site.

Uploaded by

Scylar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Flare Stack

Design Specification Sheet

Attention: Customer:
Company Name: General Location:
Phone: Site Elevation:
Fax: Required By Date:
Email: Today’s Date:
Project Reference:

EQUIPMENT REQUIREMENTS
Utility Flare: 씲 No 씲 Yes 씮 씲 Intermittent 씲 Continuous
Smokeless Flare: 씲 No 씲 Yes 씮 씲 Air-Assist 씲 Steam-Assist 씲 Gas-Assist
________ % smokeless of total flow
Support: 씲 Self-Support 씲 Guyed 씲 Derrick
Knockout Drum: 씲 No 씲 Yes 씮 씲 Integral 씲 Separate
Flame Arrestor: 씲 No 씲 Yes 씮 씲 Deflagration 씲 Detonation
Velocity Seal: 씲 No 씲 Yes
Other Seal: 씲 Molecular 씲 Liquid

DESIGN PARAMETERS
If Flare Dimensions Known: Stack diameter: in. Stack height: ft.
If Flare Dimensions Unknown:
Design Flow Rate: (scfd) (scfh) (#/hr) (mol/hr)
Allowable Pressure Drop: PSIG
Pressure of Flare Gas: PSIG
Temperature of Flare Gas: (°F) (°C)
Allowable Radiation at Grade: (BTU/ft2/hr) (kW/m2)
Atmospheric Pressure: PSI (a)
Design Regulatory Authority: 씲 API 521 씲 ASME B31.1 씲 40CFR 60.13
Fuel Gas Analysis – provide details:
Waste Gas Analysis – provide details on a separate sheet or complete page two.

PILOT AND IGNITION SYSTEM


Continuous Pilot: 씲 No 씲 Yes 씮 씲 Natural Gas 씲 Propane
Add Flame Monitor/Auto-Relight: 씲 No 씲 Yes
Electronic (Arch- Light) Igniter: 씲 No 씲 Yes
Power: Solar Package (12 VDC) 씲 No 씲 Yes
Available Onsite: 씲 No 씲 Yes 씮 씲 120 VAC 씲 24 VDC 씲 Other
Other:

Page 1 of 2

TORNADO Technologies Inc. • Tel: 403-244-3333 • Fax: 403-245-1821 • www.tornadotech.com


Flare Stack
Waste Gas Analysis

Component Mole Percent Mole Fraction Pound Moles Per Hour

TOTALS:

Page 2 of 2

TORNADO Technologies Inc. • Tel: 403-244-3333 • Fax: 403-245-1821 • www.tornadotech.com

You might also like