Technical Data Sheet

DAREX® GL 1231-04
June-2019

PRODUCT DESCRIPTION Note:

The correct film weight, curing conditions and proper stirring
DAREX® GL 1231-04 is a pale gold lacquer based on an are vital to achieve the maximum coating performance. It is
epoxy-phenolic resin combination. It is a deep drawable and recommended that all new applications be submitted to a pack
sterilization-resistant protection lacquer for the external test before use. We are at your disposal for advice on product
lacquering of crown corks and for the entire internal and usage.
external lacquering of 3-piece and deep drawn food cans, as
well as for DRD-cans and RO/PP closures. Also suitable for Handling & Storage Recommendations:
aggressive food packs. ● It is strongly recommended storing this product in the
original, closed containers.
Product Characteristics: ● For optimum performance this product should be used
Property Value within 9 months of the manufacturing date.
Color of Liquid Coating Orange-brown ● Store under uniform temperature conditions between 5
Color of Cured Coating Pale gold to 30 °C, avoid wide temperature differentials.
Total Solids, (%) 36 ± 1 ● Do not store in direct sunlight.
12 min @ 200 °C ● Viscosity increase during storage may result in the need
to adjust viscosity prior to use.
Typical Properties and Recommended Applications:
Health & Safety Information:
The following typical properties data is given for informational
For healthy and safety information, please refer to the product
purposes only and is not to be interpreted as product or
Material Safety Data Sheet. For environmental compliance
in-process specifications.
status, information will be provided upon request. For
Property Value information related to the food law compliance of this product,
Application Method Sheet Coating (Roller) please refer to the food law statement, which will be provided
upon request. Food law compliance may vary by region and
Substrate ETP, ECCS, AIuminium
this product may be restricted based on application or region.
Stirring, min. 15 to 30

Application Viscosity, (s) 65 to 100

ISO 6 mm @ 20 °C
Application Viscosity, (s) 80 to 140
DIN 4 mm @ 20 °C
Thinner TH 1010-35 / TH 1010-05
Density, (g/cm³) 1.02 ± 0.02

Single-Coat Application
Dry Film Weight, (g/m²) 4.0 to 11.0
Wet Film Weight, (g/m²) 11.0 to 30.5
Curing, (PMT) 10 min @ 200 °C

For detailed handling information see Technical Bulletin TB-022, “Best Practice
for Solvent-Borne Can Coatings“.

The standard dry film weight for the most applications is 4 to 6

g/m², while for DRD applications or acidic packs a dry film
weight of 9 to 11 g/m² is recommended.
The application performance of the lacquer and its suitability
for the required end use should be confirmed under given
industrial line conditions.
 TDS DAREX® GL 1231-04, June-2019

ADDITIONAL INFORMATION
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.

Trademark usage: [Except as otherwise noted] All trademarks in this document

are trademarks and/or registered trademarks of Henkel and its affiliates in the
U.S. and elsewhere.

Reference 1.0

Darex Packaging is part of Henkel AG & Co. KGaA. Henkelstrasse 67, 40589 Dusseldorf, Germany. Darex ® is a
registered trademark of Henkel AG & Co. KGaA. © 2017 Henkel AG & Co. KGaA
For more information, please contact us on www.henkel.com