Model Code. Series 02.

Version A2.
Valid from October 1, 2010.

1
 Model Code. HPV-02 Closed Loop (CL) Variable Displacement Pumps Model Code. HPV-02 Closed Loop (CL) Variable Displacement Pumps

Basic Specification Pump Control Pump Features Mounting Interfaces Pump PTO Internal Gear Pump Coating Pump Setup Processing Data

HPV-02 A2

Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280
55
75

55
75

55
75

55
75
1. Type HPV-02 D1 Deutsch / 12V | | | | | | | Mounting Interfaces G31 external gear pump 31 cc (*r) z z z

2. Type Code Release A2 D1 Deutsch / 24V | | | | | | | 14. Porting G38 external gear pump 38 cc z z z z z

Basic Specification 00 not applicable (M1; H1; H1P) z z z z z z z M ISO 6149 metric z z z z z z z G44 external gear pump 44 cc (*r) z z

3. Frame Size (Maximum Displacement Range) 9. Response Orifices D DIN 3852 z z z z T05 HPV/R 55-02 mount. prep. (*s) z z z z z z z

055 55 cc (28 - 55 cc) z 06 0,6 mm z z z z z z z 15. Mounting Flange T07 HPV/R 75-02 mount. prep. (*s) z z z z z z

075 75 cc (55 - 75 cc) z 07 0,7 mm z z z z z z z S0 SAE J744 standard z z z z z z T10 HPV/R 105-02 mount. prep. (*s) z z z z z

105 105 cc (75 - 105 cc) z 08 0,8 mm z z z z z z z S1 SAE J744 / additional threads (*u) z z z T13 HPV/R 135-02 mount. prep. (*s) z z z

135 135 cc (105 - 135 cc) z 09 0,9 mm z z z z z z z S2 SAE J744 / additional holes (*u) z z T16 HPV/R 165-02 mount. prep. (*s) z z

165 165 cc (135 - 165 cc) z 10 1,0 mm z z z z z z z 16. Drive Shaft (splined ANSI B92.1...) T21 HPV/R 210-02 mount. prep. (*s) z z

210 210 cc (165 - 210 cc) z 11 1,1 mm z z z z z z z S32 12/24 - 14 theeth (SAE J744 C) z z z T28 HPV/R 280-02 mount. prep. (*s) z

280 280 cc (210 - 280 cc) z 12 1,2 mm z z z z z z z S38 12/24 - 17 teeth (SAE J744 C-C) z z 000 w/o z z z z z z z

4. Rotation 13 1,3 mm z z z z z z z S44 8/16 - 13 teeth (SAE J744 D&E) z Internal Gear Pump
R cw z z z z z z z 14 1,4 mm z z z z z z z S50 8/16 - 15 teeth (SAE J744 F) z z 19. Internal Gear Pump Supply
L ccw z z z z z z z 15 1,5 mm z z z z z z z T21 16/32 - 21 teeth (*t) z z E external supply port z z z z z z

Pump Control 18 1,8 mm z z z z z z z T23 16/32 - 23 teeth (*t) z G internal supply z z z z

5. Pump Controller 21 2,1 mm z z z z z z z T27 16/32 - 27 teeth (*t) z z z 0 w/o internal gear pump z z z z z z z

M100 M1: mechanical hydraulic z z z z z z z 99 without response orifices z z z z z z z T33 16/32 - 33 teeth (*t) z 20. PTO Through Drive on Internal Gear Pump
H100 H1: hydraulic proportional z z z z z z z Pump Features Pump PTO A09 SAE J744 A/ANSI B92.1 16/32-9t (default) z z z z z z

H1P0 H1P: hydraulic proportional / PCO z z z z z z z 10. System Relief Valves 17. PTO Through Drive Configuration B00 SAE J744 B without shaft coupling z z z z

E100 E1: electro-proportional z z z z z z z 150 150 bar z z z z z z z A00 SAE J744 A w/o shaft coupl. (default) z z z z z z z B13 SAE J744 B/ANSI B92.1 16/32-13t z z z z

E1P0 E1P: electro-proportional / PCO z z z z z z z 200 200 bar z z z z z z z A09 SAE J744 A/ANSI B92.1 16/32-9t z z z z B15 SAE J744 B/ANSI B92.1 16/32-15t z z z z

E200 E2: electro-proportional / shut-off z z z z | z z 250 250 bar z z z z z z z A11 SAE J744 A/ANSI B92.1 16/32-11t z z C00 SAE J744 C w/o shaft coupling z z z z

E500 E5: electric three position z z z z z z z 285 285 bar z z A13 SAE J744 A/ANSI B92.1 16/32-13t z C14 SAE J744 C/ANSI B92.1 12/24-14t z z z z

CA00 CA: speed rel. hydr. mech. (*d)/(*r) S S S S 300 300 bar z z z z z B00 SAE J744 B w/o shaft coupling z z z z z z z 000 w/o internal gear pump z z z z z z z

6. Additional Controller Feature Specification 305 305 bar z z B13 SAE J744 B/ANSI B92.1 16/32-13t z z z z z z z Coating
M05 M1 control lever position 24° z z z z z z z 350 350 bar z z z z z z z B15 SAE J744 B/ANSI B92.1 16/32-15t z z z z z 21. Coating
M11 M1 control lever position 90° z z z z z z z 360 360 bar z z C00 SAE J744 C w/o shaft coupling z z z z z z z R00 anti rust conservation oil (default) z z z z z z z

M15 M1 control lever position 133° z z z z z z z 380 380 bar z z z z z z z C14 SAE J744 C/ANSI B92.1 12/24-14t z z z z z z z P01 primer RAL 3009 oxide red z z z z z z z

M16 M1 control lever position 144° z z z z z z z 400 400 bar z z C21 SAE J744 C/ANSI B92.1 16/32-21t z z z z P03 primer blue z z z z z z z

M20 M1 control lever position 188° z z z z z z z 420 420 bar z z z z z z z C23 SAE J744 C/ANSI B92.1 16/32-23t z z V03 primer + coating RAL 9005 black z z z z z z z

M22 M1 control lever position 210° z z z z z z z 11. Charge Relief Valve D00 SAE J744 D w/o shaft coupling z z z V04 primer + coating RAL 7043 grey z z z z z z z

M24 M1 control lever position 232° z z z z z z z 19 19 bar z z z D13 SAE J744 D/ANSI B92.1 8/16-13t z Pump Setup
E2N E2 standard destroking speed z z z z | z z 20 20 bar z z z z D17 SAE J744 D/ANSI B92.1 12/24-17t z 22. Maximum Displacement Setting P
E2F E2 accelerated destroking speed z z z z 22 22,5 bar z z z D27 SAE J744 D/ANSI B92.1 16/32-27t z z z value num. 3 digits, sett. range see pos. 3. z z z z z z z

E2H E2 quickest destroking speed z z z z | z z 23 23 bar z z z z E00 SAE J744 E w/o shaft coupling z 23. Maximum Displacement Setting S
000 not applic. (H1; H1P; E1; E1P;E5; CA) z z z z z z z 24 24 bar z z z E27 SAE J744 E/ANSI B92.1 16/32-27t z z value num. 3 digits, sett. range see pos. 3. z z z z z z z

7. Control Pressure Range Hydraulic and Electric Controls 29 29 bar z z z z E33 SAE J744 E/ANSI B92.1 16/32-33t z Special
A 4-10 bar z z z z z z z 00 purge orifice z z z z z z z GP0 for Linde gear pumps (see 18.) z z z z z z z 24. Special Requirements
B 4-16 bar z z z z z z z 12. Filter Configuration 18. PTO Through Drive Attachment N w/o special requirements (default) z z z z z z z

0 not applicable (M1) z z z z z z z F filter flange with filter cartridge z z z z z z z A16 internal gear pump 16 cc z z z z C with special requirements S S S S S S S

8. Control Solenoids E 90° charge port flange z z z z z z z A22 internal gear pump 22,5 cc z z z z Processing Data
A1 AMP / 12V z z z z z z z D straight charge port flange z z z z B32 internal gear pump 16+16 cc z z z z 25. Customer Identification Number
A2 AMP / 24 V z z z z z z z 13. Swash Angle Sensor B38 internal gear pump 16+22,5 cc z z z z value numeric 6 digits

H1 DIN / 12 V z z z z z z z S with swash angle sensor z z z z z C38 internal gear pump 22,5+16 cc z z z z 26. Customer Part Number
H2 DIN / 24 V z z z z z z z 0 w/o swash angle sensor z z z z z z z C45 internal gear pump 22,5+22,5 cc z z z z z z value alpha numeric 10 digits

(*r) cw rotation only (see pos. 4.) (*t) recommended if HPV/R-02 unit is attached to PTO (see pos. 18.) (*r) cw rotation only (see pos. 4.) (*t) recommended if HPV/R-02 unit is attached to PTO (see pos. 18.)
(*d) DIN porting only (see pos. 14.) (*u) required if second unit is attached to PTO (see pos. 18.) (*d) DIN porting only (see pos. 14.) (*u) required if second unit is attached to PTO (see pos. 18.)
(*m) ISO metric porting only (see pos. 14.) (*s) second HPV/R-02 unit has to be specified separately (*m) ISO metric porting only (see pos. 14.) (*s) second HPV/R-02 unit has to be specified separately

2 Valid from October 1, 2010 Valid from October 1, 2010 3

 Model Code. HPR-02 Open Loop (OL) Variable Displacement Pumps Model Code. HPR-02 Open Loop (OL) Variable Displacement Pumps

Basic Specification Pump Control Pump Features Mounting Interfaces Pump PTO Internal Gear Pump Coating Pump Setup Processing Data

HPR-02 A2

Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280
55
75

55
75

55
75

55
75
1. Type HPR-02 D DIN 3852 z z z z C38 internal gear pump 22,5+16 cc z z z z 21. Pressure Cut-Off Setting
2. Type Code Release A2 11. Mounting Flange C45 internal gear pump 22,5+22,5 cc z z z z value 125 - 420 bar (numeric 3 digits) z z z z z z z

Basic Specification S0 SAE J744 standard z z z z z z G31 external gear pump 31 cc (*r) z z 999 not applicable (H1L; E1L; TL2) z z z z z z z

3. Frame Size S1 SAE J744 / additional threads (*u) z z G38 external gear pump 38 cc z z z z 22. Power Limiter Setting
055 55 cc (35 - 55 cc) z S2 SAE J744 / additional holes (*u) z G44 external gear pump 44 cc (*r) z z value 35 - 105 kW (numeric 3 digits) z

075 75 cc (50 - 75 cc) z M0 ISO 30119-2 metric (*m) z z H45 ext. gear pump 22,5+22,5 cc (cw rot.only) z z z z value 44 - 135 kW (numeric 3 digits) z

105 105 cc (75 - 105 cc) z P0 plug-in (size 105: (*d)) z z T05 HPV/R 55-02 mount. prep. (*s) z z z z z z z value 60 - 175 kW (numeric 3 digits) z

135 135 cc (105 - 135 cc) z B3 bell housing SAE 3 (size 105: (*d)) z z T07 HPV/R 75-02 mount. prep. (*s) z z z z z z value 70 - 210 kW (numeric 3 digits) z

165 165 cc (135 - 165 cc) z B4 bell housing SAE 4 (size 105: (*d)) z z T10 HPV/R 105-02 mount. prep. (*s) z z z z z 999 not applicable (LP; H1L; E1L; LEP) z z z z z z z

210 210 cc (160 - 210 cc) z 12. Drive Shaft (S32 - T27: splined ANSI B92.1...) T13 HPV/R 135-02 mount.prep. (*s) z z z Special
280 280 cc (210 - 280 cc) z S32 12/24 - 14 theeth (SAE J744 C) z z z T21 HPV/R 210-02 mount. prep. (*s) z z 23. Special Requirements
4. Rotation S38 12/24 - 17 teeth (SAE J744 C-C) z z T28 HPV/R 280-02 mount.prep. (*s) z N w/o special requirements (default) z z z z z z z

R cw z z z z z z z S44 8/16 - 13 teeth (SAE J744 D&E) z z 000 w/o z z z z z z z C with special requirements S S S S S S S

L ccw z z z z z z S50 8/16 - 15 teeth (SAE J744 F) z z Internal Gear Pump Processing Data
Pump Control T21 16/32 - 21 teeth (*t) z 15. Internal Gear Pump Supply 24. Customer Identification Number
5. Pump Controller T23 16/32 - 23 teeth (*t) z E external supply port z z z z value numeric 6 digits

LP00 LP: LS / pressure cut-off z z z z z z T27 16/32 - 27 teeth (*t) z z z 0 w/o internal gear pump z z z z z z z 25. Customer Part Number
H1L0 H1L: LS / hydraulic override (*m) z z z z z z P40 keyed ISO3019-2 / 40 mm z 16. PTO Through Drive on Internal Gear Pump (A09 - C14: SAE J744 ...) value alpha numeric 10 digits

E1L0 E1L: LS / electric override (*m) z z z z z z P60 keyed ISO3019-2 / 60 mm z A09 A / ANSI B92.1 16/32 - 9 t. (A) (default) z z z z

TL20 TL2: LS / power limiter (*m)/(*r) z z z z Pump PTO B00 B w/o shaft coupling z z z z

ETP0 ETP: elec.-prop./power lim./PCO (*m)/(*r) z z z z 13. PTO Through Drive Configuration (A00 - E33: SAE J744 ...) B13 B / ANSI B92.1 16/32 - 13 t. (B) z z z z

LEP0 LEP: LS/elec. stroke lim./PCO (*m)/(*r) z z z z A00 A w/o shaft coupling (default) z z z z z z z B15 B / ANSI B92.1 16/32 - 15 t. (B-B) z z z z

6. Pressure Limiter Remote Control A09 A / ANSI B92.1 16/32 - 9 teeth (A) z z z z z z C00 C w/o shaft coupling z z

D disabled (ETP; LEP only) z z z z A11 A / ANSI B92.1 16/32 - 11 teeth z z C14 C / ANSI B92.1 12/24 - 14 t.(C) z z

R enabled (ETP; LEP only) z z z z A13 A / ANSI B92.1 16/32 - 13 teeth z z z z 000 w/o internal gear pump z z z z z z z

0 not applicable (LP; H1L; E1L;TL2) z z z z z z z B00 B w/o shaft coupling z z z z z z z Coating
7. Power Limiter Remote Control B13 B / ANSI B92.1 16/32 - 13 t. (B) z z z z z z 17. Coating
Z1 power uprating (TL2; ETP only) z z z z B15 B / ANSI B92.1 16/32 - 15 t. (B-B) z z z z z R00 anti rust conservation oil (default) z z z z z z z

Z2 power up- & downrat. (TL2; ETP only) z z z z C00 C w/o shaft coupling z z z z z z z P01 primer RAL 3009 oxide red z z z z z z z

00 not applicable (LP; H1L; E1L;TL2) z z z z z z z C14 C / ANSI B92.1 12/24 - 14 t. (C) z z z z z z z P03 primer blue z z z z z z z

8. Control Solenoids C21 C / ANSI B92.1 16/32 - 21 teeth z z z V03 primer + coating RAL 9005 black z z z z z z z

A1 AMP / 12V z z z z z z | C23 C / ANSI B92.1 16/32 - 23 teeth z z z V04 primer + coating RAL 7043 grey z z z z z z z

A2 AMP / 24 V z z z z z z z D00 D w/o shaft coupling z z z z Pump Setup

H1 DIN / 12 V z z z z z z | D13 D / ANSI B92.1 8/16 - 13 teeth (D) z 18. Maximum Displacement Setting
H2 DIN / 24 V z z z z z z | D17 D / ANSI B92.1 12/24 - 17 teeth z value num. 3 digits, sett. range see pos 3. z z z z z z z

D1 Deutsch / 12V | | | | | | | D27 D / ANSI B92.1 16/32 - 27 teeth z z z 19. Operating Speed
D1 Deutsch / 24V | | | | | | | E00 E w/o shaft coupling z z value 800 - 2.700 rpm (numeric 4 digits) z

00 not applicable (LP; H1L; TL2) z z z z z z z E27 E / ANSI B92.1 16/32 - 27 teeth z value 800 - 2.600 rpm (numeric 4 digits) z

Pump Features E33 E / ANSI B92.1 16/32 - 33 teeth z value 800 - 2.300 rpm (numeric 4 digits) z z

9. Noise Optimization Devices GP0 for Linde gear pump attachment z z z z z z value 800 - 2.100 rpm (numeric 4 digits) z

S with SPU primary noise reduction z z z z z z z 14. PTO Through Drive Attachment value 800 - 2.000 rpm (numeric 4 digits) z

0 w/o add. noise optimization dev. z z z z z z A16 internal gear pump 16 cc z z z z value 800 - 1.800 rpm (numeric 4 digits) z

Mounting Interfaces A22 internal gear pump 22,5 cc z z z z 20. LS Differential Pressure Setting
10. Porting B32 internal gear pump 16+16 cc z z z z value 16 - 30 bar (numeric 2 digits) z z z z z z z

M ISO 6149 metric z z z z z z z B38 internal gear pump 16+22,5 cc z z z z 99 not applicable (ETP) z z z z z z z

(*r) cw rotation only (see pos. 4.) (*t) recommended if HPV/R-02 unit is att. to PTO (see pos. 14.) (*r) cw rotation only (see pos. 4.) (*t) recommended if HPV/R-02 unit is att. to PTO (see pos. 14.)
(*d) DIN porting only (see pos. 10.) (*u) required if HPV/R-02 unit is attached to PTO (see pos. 14.) (*d) DIN porting only (see pos. 10.) (*u) required if HPV/R-02 unit is attached to PTO (see pos. 14.)
(*m) ISO metric porting only (see pos. 10.) (*s) second HPV/R-02 unit has to be specified separately (*m) ISO metric porting only (see pos. 10.) (*s) second HPV/R-02 unit has to be specified separately

4 Valid from October 1, 2010 Valid from October 1, 2010 5

 Model Code. HMV-02 Variable Displacement Motors (OL & CL) Model Code. HMV-02 Variable Displacement Motors (OL & CL)

Basic Specification Motor Control Motor Features Mounting Interfaces Motor PTO Additions Coating Motor Setup Processing Data

HMV-02 A2

Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280
55
75

55
75

55
75
1. Type HMV-02 07 0,7 mm z z z z z z z Motor PTO
2. Type Code Release A2 08 0,8 mm z z z z z z z 14. PTO & Service Ports Orientation (S19 - U35: radial ports ...)
Basic Specification 09 0,9 mm z z z z z z z R00 radial ports / without PTO z z z z z z z

3. Frame Size 10 1,0 mm z z z z z z z L00 axial ports / without PTO z z z

055 55 cc z 11 1,1 mm z z z z z z z S19 splined PTO shaft ANSI B92.1 16/32 - 19 t. z

075 75 cc z 12 1,2 mm z z z z z z z S21 splined PTO shaft ANSI B92.1 16/32 - 21 t. z

105 105 cc z 13 1,3 mm z z z z z z z S22 splined PTO shaft ANSI B92.1 16/32 - 22 t. z

135 135 cc z 14 1,4 mm z z z z z z z S24 splined PTO shaft ANSI B92.1 16/32 - 24 t. z

165 165 cc z 15 1,5 mm z z z z z z z S27 splined PTO shaft ANSI B92.1 16/32 - 27 t. z

210 210 cc z 18 1,8 mm z z z z z z z F40 PTO shaft coupling flange size 4 z z

280 280 cc z 21 2,1 mm z z z z z z z U35 PTO speed sensor 35 impulses z z z z z z z

4. Rotation 99 w/o response orifices z z z z z z z Additions

N cw / ccw z z z z z z z Motor Features 15. Attachments to Service Ports
Motor Control 9. Purge Relief Valve P25 crossover relief block 250 bar (*p) z z z

5. Motor Control N10 10 bar standard purge flow z z z z z z z P30 crossover relief block 300 bar (*p) z z z

H100 H1: hydr. prop./ standard mounting z z z z z z z N14 14 bar standard purge flow z z z z z z z P38 crossover relief block 380 bar (*p) z z z

E100 E1: electro-prop./ standard mounting z z z z z z z R10 10 bar reduced purge flow z z z z z z z P42 crossover relief block 420 bar (*p) z z z

E200 E2: electric two pos. / standard mounting z z z z z z z R14 14 bar reduced purge flow z z z z z z z 000 w/o z z z z z z z

E400 E4: e-prop./ Vmin = 0 /standard mounting z z z z z z z H10 10 bar increased purge flow z z z z z z z Coating
E600 E6: e-prop./ Vmin = 0/ standard mounting z z z z z Q06 flow controlled 6 l/min (*o) z z z z z z z 16. Coating
E1F0 E1F: electro-proportional /side-mounted z B00 blank plug inst. of relief valve (*v) z z z z z z z R00 anti rust conservation oil (default) z z z z z z z

E2F0 E2F: electric two position / side-mounted z 000 w/o purge devices z z P01 primer RAL 3009 oxide red z z z z z z z

E4F0 E4F: e-prop./ Vmin = 0 / side-mounted z z 10. Purge Shuttle Valve P03 primer blue z z z z z z z

E6F0 E6F e-prop./ Vmin = 0 / side-mounted z z N0 standard shuttle valve z z z z z z z V03 primer + coating RAL 9005 black z z z z z z z

H1P0 EH1P: hydraulic proportional / PCO z z z z D0 damped shuttle valve z z z z z z z V04 primer + coating RAL 7043 grey z z z z z z z

H1C0 H1-CA: hydraulic prop./ CA operation (*m) z z B0 shuttle valve blocked z z z z z z z Motor Setup
H1PC EH1P-CA: hydr. prop./ PCO / CA operation z z z z 00 w/o purge devices z z 17. Minimum Displacement Setting
6. Start of Control Mounting Interfaces value 0 - 35 cc (numeric 3 digits) z

HF0 7,0 bar (H1; EH1P; EH1P-CA) z z z z z z z 11. Porting value 0 - 75 cc (numeric 3 digits) z

HF5 7,5 bar (H1; EH1P; H1-CA) z z z z z z z M ISO 6149 metric z z z z z z value 0 - 85 cc (numeric 3 digits) z

HH0 8,0 bar (H1; EH1P) z z z z z z z D DIN 3852 z z z z value 0 - 135 cc (numeric 3 digits) z

HH5 8,5 bar (H1; EH1P) z z z z z z z 12. Mounting Flange value 0 - 108 cc (numeric 3 digits) z

HK0 9,0 bar (H1; EH1P) z z z z z z z S0 SAE J744 standard z z z z z z z value 0 - 150 cc (numeric 3 digits) z

HK5 9,5 bar (H1; EH1P) z z z z z z z P0 plug-in (*d) z z z value 0 - 280 cc (numeric 3 digits) z

000 not applic. (E1(F); E2(F); E4(F); E6(F)) z z z z z z z 13. Drive shaft (S32 - T33: splined ANSI B92.1...) 18. Pressure Override Setting (numeric 3 digits)
7. Control Solenoids S32 12/24 - 14 theeth (SAE J744 C) z z z value 190-260 bar (EH1P; EH1P-CA only) z z z z z

A1 AMP / 12V z z z z z z z S44 8/16 - 13 teeth (SAE J744 D&E) z z 999 not applicable z z z z z z z

A2 AMP / 24 V z z z z z z z S50 8/16 - 15 teeth (SAE J744 F) z z 19. Special Requirements

H1 DIN / 12 V z z z z z z z T21 16/32 - 21 teeth z z N w/o special requirements (default) z z z z z z z

H2 DIN / 24 V z z z z z z z T23 16/32 - 23 teeth z C with special requirements S S S S S S S

D1 Deutsch / 12V | | | | | | | T27 16/32 - 27 teeth z z z Processing Data

D1 Deutsch / 24V | | | | | | | T33 16/32 - 33 teeth z 20. Customer Identification Number
00 not applicable (H1; H1-CA; H2) z z z z z z z F40 shaft coupling flange size 4 z z value numeric 6 digits

8. Response Orifices 21. Customer Part Number

06 0,6 mm z z z z z z z value alpha numeric 10 digits

(*d) DIN porting only (see pos. 11.) (*p) radial service ports only (see pos. 14.) (*d) DIN porting only (see pos. 11.) (*p) radial service ports only (see pos. 14.)
(*m) ISO metric porting only (see pos. 11.) (*v) with blocked purge shuttle valve only (see pos. 10.) (*m) ISO metric porting only (see pos. 11.) (*v) with blocked purge shuttle valve only (see pos. 10.)
(*o) open loop operation only (*o) open loop operation only

6 Valid from October 1, 2010 Valid from October 1, 2010 7

 Model Code. HMR-02 Regulated Variable Displacement Motors (OL+CL) Model Code. HMR-02 Regulated Variable Displacement Motors (OL+CL)

Basic Specification Controller Features Motor Control Mounting Interfaces PTO Additions Coating Motor Setup Processing Data

HMR-02 A2

Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice

105
135
165
210
280

105
135
165
210
280

105
135
165
210
280
75

75

75
1. Type HMR-02 99 w/o response orifices z z z z z z U35 PTO speed sensor 35 impulses z

2. Type Code Release A2 Motor Control Additions

Basic Specification 10. Crossover Relief Valves Integrated (single-stage ...) 17. Attachments to Service Ports
3. Frame Size 25N 250 bar (*q) / f. sizes 75;165: (*l) z z z z P25 crossover relief block 250 bar (*p) z z z

075 75 cc z 27N 270 bar (*q) / f. sizes 75;165: (*l) z z z z P30 crossover relief block 300 bar (*p) z z z

105 105 cc z 30N 300 bar (*q) / f. sizes 75;165: (*l) z z z z P38 crossover relief block 380 bar (*p) z z z

135 135 cc z 33N 330 bar (*q) / f. sizes 75;165: (*l) z z z z P42 crossover relief block 420 bar (*p) z z z

165 165 cc z 35N 350 bar (*q) / f. sizes 75;165: (*l) z z z z BM0 prop. brake valve (wheel. appl.) (*o)/(*b) | | | | |

210 210 cc z 42N 420 bar (*q) / f. sizes 75;165: (*l) z z z z 000 w/o z z z z z z

280 280 cc z 000 w/o z z z z z z Coating

4. Rotation 11. Purge Relief Valve 18. Coating
N cw / ccw z z z z z z N10 10 bar standard purge flow z z z z z z R00 anti rust conservation oil (default) z z z z z z

Controller Features N14 14 bar standard purge flow z z z z z z P01 primer RAL 3009 oxide red z z z z z z

5. Motor Controller R10 10 bar reduced purge flow z z z z z z P03 primer blue z z z z z z

P pressure regulated z z z z z z R14 14 bar reduced purge flow z z z z z z V03 primer + coating RAL 9005 black z z z z z z

6. Regulating Pressure Selection H10 10 bar increased purge flow z z z z z z V04 primer + coating RAL 7043 grey z z z z z z

S highest service port pressure z z z z z z Q06 flow controlled 6 l/min (*o) z z z z z z Motor Setup
E electrically switched (*c) z z z z z z B00 blank plug instead of relief valve (*v) z z z z z z 19. Minimum Displacement Setting
B through brake valve (*o) | | | | | 000 w/o purge devices z z z z value 22 - 55 cc (numeric 3 digits) z

7. Displacement Override 12. Purge Shuttle Valve value 0 - 75 cc (numeric 3 digits) z

E electric (*c) z z z z z z N0 standard shuttle valve z z z z z z value 0 - 85 cc (numeric 3 digits) z

H hydraulic high pressure (*o) z z z z z z D0 damped shuttle valve z z z z z z value 52 - 100 cc (numeric 3 digits) z

L hydraulic low pressure (*o) z z z z z z B0 shuttle valve blocked z z z z z z value 0 - 210 cc (numeric 3 digits) z

0 w/o z z z z z z 00 w/o purge devices z z z z value 0 - 280 cc (numeric 3 digits) z

8. Control Solenoids Mounting Interfaces 20. Pressure Override Setting

A1 AMP / 12V z z z z z 13. Porting value 190 - 260 bar (numeric 3 digits) z z z z z

A2 AMP / 24 V z z z z z M ISO 6149 metric z z z z Special

H1 DIN / 12 V z z z z z D DIN 3852 z z z 21. Special Requirements
H2 DIN / 24 V z z z z z 14. Mounting Flange N w/o special requirements (default) z z z z z z

D1 Deutsch / 12V | | | | | S0 SAE J744 standard z z z z z z C with special requirements S S S S S S

D1 Deutsch / 24V | | | | | P0 plug-in (*d) z Processing Data

00 not applicable z z z z z z 15. Drive shaft (S32 - T27: splined ANSI B92.1...) 22. Customer Identification Number
9. Response Orifices S32 12/24 - 14 theeth (SAE J744 C) z z value numeric 6 digits

06 0,6 mm z z z z z z S44 8/16 - 13 teeth (SAE J744 D&E) z z 23. Customer Part Number
07 0,7 mm z z z z z z S50 8/16 - 15 teeth (SAE J744 F) z z value alpha numeric 10 digits

08 0,8 mm z z z z z z T21 16/32 - 21 teeth z

09 0,9 mm z z z z z z T23 16/32 - 23 teeth z

10 1,0 mm z z z z z z T27 16/32 - 27 teeth z z z

11 1,1 mm z z z z z z T33 16/32 - 33 teeth z

12 1,2 mm z z z z z z F40 shaft coupling flange size 4 z z

13 1,3 mm z z z z z z PTO
14 1,4 mm z z z z z z 16. PTO & Service Ports Orientation (S21 - U35: radial ports ...)
15 1,5 mm z z z z z z R00 radial ports / without PTO z z z z z z

18 1,8 mm z z z z z z L00 axial ports / without PTO z z z z

21 2,1 mm z z z z z z S21 spl. PTO shaft ANSI B92.1 16/32 - 21 t. z

(*d) DIN porting only (see pos. 13.) (*b) regulating pressure selection through brake valve required (see pos. 6.) (*d) DIN porting only (see pos. 13.) (*b) regulating pressure selection through brake valve required (see pos. 6.)
(*m) ISO metric porting only (see pos. 13.) (*p) radial service ports only (see pos. 16.) (*m) ISO metric porting only (see pos. 13.) (*p) radial service ports only (see pos. 16.)
(*o) open loop operation only (*l) axial service ports only (see pos. 16.) (*o) open loop operation only (*l) axial service ports only (see pos. 16.)
(*c) closed loop operation only (*q) without purging devices only (see pos. 11. & 12.) (*c) closed loop operation only (*q) without purging devices only (see pos. 11. & 12.)
(*v) with blocked purge shuttle valve only (see pos. 12.) (*v) with blocked purge shuttle valve only (see pos. 12.)

8 Valid from October 1, 2010 Valid from October 1, 2010 9

 Model Code. HMF-02 Fixed Displacement Motors (OL+CL) Model Code. HMA-02 Adjustable Fixed Displacement Motors (OL+CL)

Basic Specification Motor Features Mounting Interfaces PTO Additions Coating Processing Data Basic Specification Motor Features Mounting Interfaces PTO Additions Coating Motor Setup Processing Data

HMF-02 A2 HMA-02 A2

Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice Item Feature Frame Size Choice

105
135

105
135

105
135
165
210
280

105
135
165
210
280
28
35
50
55
63
75

28
35
50
55
63
75

55
75

55
75
1. Type HMF-02 D0 damped shuttle valve z z z z z z z z 1. Type HMA-02 V03 primer + coating RAL 9005 black z z

2. Type Code Release A2 B0 shuttle valve blocked z z z z z z z z 2. Type Code Release A2 V04 primer + coating RAL 7043 grey z z

Basic Specification 00 w/o purge devices z z z z z z z Basic Specification Motor Setup

3. Frame Size 8. Speed Sensor in Motor Housing 3. Frame Size 13. Displacement Setting
028 28 cc z U07 7 impulses z z 165 165 cc z value 135 - 165 cc (numeric 3 digits) z

035 35 cc z U09 9 impulses z 210 210 cc z value 165 - 210 cc (numeric 3 digits) z

050 50 cc z 000 w/o z z z z z z z z 4. Rotation Special

055 55 cc z Mounting Interfaces N cw / ccw z z 14. Special Requirements
063 63 cc z 9. Porting Motor Features N w/o special requirements (default) z z

075 75 cc z M ISO 6149 metric z z z z 5. Purge Relief Valve C with special requirements S S

105 105 cc z D DIN 3852 z z z z z z z z N10 10 bar standard purge flow z z Processing Data
135 135 cc z 10. Mounting Flange N14 14 bar standard purge flow z z 15. Customer Identification Number
4. Rotation S0 SAE J744 standard z z z z z z z z R10 10 bar reduced purge flow z z value numeric 6 digits

N cw / ccw z z z z z z z z 11. Drive shaft (S25 - T27: splined ANSI B92.1...) R14 14 bar reduced purge flow z z 16. Customer Part Number
Motor Features S25 16/32 - 15 theeth (SAE J744 B-B) z z H10 10 bar increased purge flow z z value alpha numeric 10 digits

5. Crossover Relief Valves Integrated S32 12/24 - 14 theeth (SAE J744 C) z z z z z Q06 flow controlled 6 l/min (*o) z z

21N single-stage 210 bar (*p)/(*q) z z z z z z z S44 8/16 - 13 teeth (SAE J744 D&E) z B00 blank plug instead of relief valve (*v) z z

23N single-stage 230 bar (*p)/(*q) z z z z z z z T21 16/32 - 21 teeth z z z z z 6. Purge Shuttle Valve
25N single-stage 250 bar (*p)/(*q) z z z z z z z T23 16/32 - 23 teeth z N0 standard shuttle valve z z

27N single stage 270 bar (*p)/(*q) z z z z z z z T27 16/32 - 27 teeth z D0 damped shuttle valve z z

30N single-stage 300 bar (*p)/(*q) z z z z z z z PTO B0 shuttle valve blocked z z

33N single stage 330 bar (*p)/(*q) z z z z z z z 12. PTO & Service Ports Orientation Mounting Interfaces
35N single-stage 350 bar (*p)/(*q) z z z z z z z R00 radial ports / w/o PTO z z z z z z z z 7. Porting
42N single-stage 420 bar (*p)/(*q) z z z z z z z L00 axial ports / w/o PTO z z z z M ISO 6149 metric z z

09E two-stage 90/230 bar (*p)/(*q) z z z z z z z Additions 8. Mounting Flange

09G two-stage 90/250 bar (*p)/(*q) z z z z z z z 13. Attachments to Service Port S0 SAE J744 standard z z

09L two-stage 90/280 bar (*p)/(*q) z z z z z z z 000 w/o z z z z z z z z 9. Drive shaft (S32 - T27: splined ANSI B92.1...)
11B two-stage 110/230 bar (*p)/(*q) z z z z z z z Coating S44 8/16 - 13 teeth (SAE J744 D&E) z

11H two-stage 110/280 bar (*p)/(*q) z z z z z z z 14. Attachments to Service Port S50 8/16 - 15 teeth (SAE J744 F) z

11M two-stage 110/310 bar (*p)/(*q) z z z z z z z R00 anti rust conservation oil (default) z z z z z z z z T27 16/32 - 27 teeth z z

14E two-stage 140/280 bar (*p)/(*q) z z z z z z z P01 primer RAL 3009 oxide red z z z z z z z z PTO
18A two-stage 180/280 bar (*p)/(*q) z z z z z z z P03 primer blue z z z z z z z z 10. PTO & Service Ports Orientation (S21 - U35: radial ports ...)
20K two-stage 200/380 bar (*p)/(*q) z z z z z z z V03 primer + coating RAL 9005 black z z z z z z z z R00 radial ports / without PTO z z

000 w/o z z z z z z z z V04 primer + coating RAL 7043 grey z z z z z z z z Additions

6. Purge Relief Valve Special 11. Attachments to Service Ports
N10 10 bar standard purge flow z z z z z z z z 15. Special Requirements P25 crossover relief block 250 bar (*p) z z

N14 14 bar standard purge flow z z z z z z z z N w/o special requirements (default) z z z z z z z z P30 crossover relief block 300 bar (*p) z z

R10 10 bar reduced purge flow z z z z z z z z C with special requirements S S S S S S S S P38 crossover relief block 380 bar (*p) z z

R14 14 bar reduced purge flow z z z z z z z z Processing Data P42 crossover relief block 420 bar (*p) z z

H10 10 bar increased purge flow z z z z z z z z 16. Customer Identification Number 000 w/o z z

Q06 flow controlled 6 l/min (*o) z z z z z z z z value numeric 6 digits Coating

B00 blank plug instead of relief valve (*v) z z z z z z z z 17. Customer Part Number 12. Coating
000 w/o purge devices z z z z z z z value alpha numeric 10 digits R00 anti rust conservation oil (default) z z

7. Purge Shuttle Valve P01 primer RAL 3009 oxide red z z

N0 standard shuttle valve z z z z z z z z P03 primer blue z z

(*o) open loop operation only (*o) open loop operation only
(*p) radial service ports only (see pos. 12.) (*p) radial service ports only (see pos. 10.)
(*q) without purging devices only (see pos. 6. & 7.) (*v) with blocked purge shuttle valve only (see pos. 6.)
(*v) with blocked purge shuttle valve only (see pos. 7.)

10 Valid from October 1, 2010 Valid from October 1, 2010 11

Linde Hydraulics. How to reach us.

Internet www.linde-hydraulics.com

Phone +49.60 21.99-42 01

+49.60 21.99-0 switchboard

Fax +49.60 21.99-42 02

+49.60 21.99-42 30

E-Mail [email protected]

Mail Linde Material Handling GmbH

LHY.Model Code.A2.10/10.e
Linde Hydraulics

Grossostheimer Str. 198

63741 Aschaffenburg

P.O. Box 100136

63701 Aschaffenburg

Linde Hydraulics, Grossostheimer Str. 198, 63741 Aschaffenburg, Germany

phone +49.60 21.99-42 01, fax +49.60 21.99-42 02, www.linde-hydraulics.com 12