Scribd
Upload
198 views3 pages

Two Way Slab

The document describes the design of two-way slabs for a three-storey commercial and pharmaceutical building with a roof deck located in Quezon City, Philippines. It provides design parameters, load assumptions, and calculations for slab thickness, reinforcement requirements, and steel ratios for Slab S-1 under two different span conditions. Tables show the required and provided reinforcement for the long and short directions at continuous edges, midspans, and discontinuous edges.

Uploaded by

Henry Tugano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
198 views3 pages

Two Way Slab

The document describes the design of two-way slabs for a three-storey commercial and pharmaceutical building with a roof deck located in Quezon City, Philippines. It provides design parameters, load assumptions, and calculations for slab thickness, reinforcement requirements, and steel ratios for Slab S-1 under two different span conditions. Tables show the required and provided reinforcement for the long and short directions at continuous edges, midspans, and discontinuous edges.

Uploaded by

Henry Tugano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Project: Three Storey Commercial & Pharmaceutical Building with Roof Deck

Location: Quezon City


Date September 2020

DESIGN OF TWO - WAY SLAB

Design Constants :

fy = 276 MPa
fc' = 28 MPa
rg = 0.002 Dead Loads :
rmax = 0.04097 Floor Finish = 1.10 kPa
rmin = 0.00580 Restroom = 1.10 kPa
m = 7.91966 Ceiling = 0.15 kPa
Movable Partition = 1.00 kPa
Unit Weight of = 24 kN/m3
Reinforced Concrete Live Loads :
Assume Beam width = 0.300 m Basic Floor Area = 4.80 kPa
Restroom = 4.80 kPa
Slab Thickness :
Typical Floors = 130 mm
Conc. Cover = 20 mm All Floors :
Smax (Long Direction) = 260 mm
Bar Diameters : Smax (Short Direction) = 260 mm
Long Direction = 10 mm Eff. d (Long Direction) = 95 mm
Short Direction = 10 mm Eff. d (Short Direction) = 95 mm

Two way slab.xlsx


E:\Commercial Building\Design\
Design of Slab for S - 1 :

Clear Span : 1.2WDL = 6.44 kPa Case no. : 2


Long Direction = 6.00 m 1.6WL = 7.68 kPa
m = (La/Lb) = 0.917
Short Direction = 5.50 m WU = 14.12 kPa

Design Moments & Reinforcements :

Negative Moments at Continuous edge


m 0.9 0.95 0.917
Ca,neg 0.055 0.05 0.05333 Ma,neg = 22.787 kN
Cb,neg 0.037 0.041 0.03833 Mb,neg = 19.491 kN

Positive Moments
m 0.9 0.95 0.917
Ca,pos. dl 0.022 0.02 0.02133 Ma,pos. dl = 4.159 kN
Cb,pos. dl 0.014 0.016 0.01467 Ma,pos. ll = 7.589 kN
Ca,pos. ll 0.034 0.03 0.03267 Ma,pos. Total = 11.748 kN
Cb,pos. ll 0.022 0.025 0.02300 Mb,pos. dl = 3.402 kN
Mb,pos. ll = 6.359 kN
Negative Moments at Discontinuous edge Mb,pos. Total = 9.761 kN
Ma,neg = 0.000 kN
Mb,neg = 0.000 kN

Short Direction Long Direction


Slab ID
Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment (kN) 22.787 11.748 0.000 19.491 9.761 0.000
h (mm) 130 130 130 130 130 130
d (mm) 95 95 95 95 95 95
X 0.01016 0.00524 0.00000 0.00869 0.00435 0.00000
Req'd r 0.01061 0.00535 0.00000 0.00902 0.00443 0.00000
Use r 0.01061 0.00580 0.00000 0.00902 0.00580 0.00000
Req'd s 77.92 142.54 NA 91.69 142.54 NA
Use s 70 140 NA 90 140 NA

Two way slab.xlsx


E:\Commercial Building\Design\
Design of Slab for S -1 :

Clear Span : 1.2WDL = 6.44 kPa Case no. : 6


Long Direction = 6.00 m 1.6WL = 7.68 kPa
m = (La/Lb) = 0.767
Short Direction = 4.60 m WU = 14.12 kPa

Design Moments & Reinforcements :

Negative Moments at Continuous edge


m 0.75 0.8 0.767
Ca,neg 0.088 0.086 0.08733 Ma,neg = 26.101 kN
Cb,neg 0 0 0.00000 Mb,neg = 0.000 kN

Positive Moments
m 0.75 0.8 0.767
Ca,pos. dl 0.048 0.045 0.04700 Ma,pos. dl = 6.409 kN
Cb,pos. dl 0.012 0.015 0.01300 Ma,pos. ll = 8.721 kN
Ca,pos. ll 0.055 0.051 0.05367 Ma,pos. Total = 15.130 kN
Cb,pos. ll 0.016 0.019 0.01700 Mb,pos. dl = 3.016 kN
Mb,pos. ll = 4.700 kN
Negative Moments at Discontinuous edge Mb,pos. Total = 7.716 kN
Ma,neg = 5.043 kN
Mb,neg = 2.572 kN

Short Direction Long Direction


Slab ID
Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment (kN) 26.10078 15.12999 5.04333 0.00000 7.71595 2.57198
h (mm) 130 130 130 130 130 130
d (mm) 95 95 95 95 95 95
X 0.01164 0.00675 0.00225 0.00000 0.00344 0.00115
Req'd r 0.01224 0.00694 0.00227 0.00000 0.00349 0.00115
Use r 0.01224 0.00694 0.00303 0.00000 0.00465 0.00154
Req'd s 67.56830 119.13103 273.14126 NA 177.66136 537.98663
Use s 60 110 260 260 170 260

Two way slab.xlsx


E:\Commercial Building\Design\

You might also like