Types of Chassis

Chassis and Types

The automobile vehicles both passenger car and goods trucks, are generally considered
to be made up of two major assemblies:

1. Chassis
2. Body

So in this article, we are focusing on Chassis, Frames, and the types of chassis and
frames.

What is Chassis?
The Chassis is a French word and was originally use to indicate the frame or main
structure of a vehicle. And now it is use to indicate the complete vehicle except the body
for the heavy vehicle having a separate body.

Chassis is the most important part of a vehicle and only fewer people care about it.
Chassis contains all the major parts to propel the vehicle, direct its movement, stop it,
and also run smoothly over uneven surfaces. It is also known as a carrying unit because
all of the components are mounted on it including the body.

In this article we are not talking about which types of chassis you want to use, instead,
we are looking at some of the chassis that we help you to determine the potential of
your vehicle.

TheEngineersPost.com Page 1
 Types of Chassis

Types of Chassis
Following are the types of chassis according to the fitting of engine:

1. Conventional Chassis 5. Bus chassis

2. Non-Conventional Chassis 6. Engine in front
3. Full forward 7. Engine at the center
4. Semi forward
#1 Conventional chassis

It is also known as a non-load-carrying frame. This type of conventional chassis is made

as a separate unit and joined with a ladder frame. This supports all the systems like
braking system, transmission system, suspension system, etc. These chassis frames are
normally seen in large trucks and SUVs. Here loads on the vehicle transferred to the
suspension system by frame.

#2 Non-conventional chassis

It is also known as frameless chassis or unibody chassis. This type of chassis doesn't
have a ladder frame the body itself acts as a frame. It also supports all the parts and
components of the vehicles. These are mostly used on most modern vehicles just as
conventional chassis.

TheEngineersPost.com Page 2
 Types of Chassis

TheEngineersPost.com Page 3
 Types of Chassis

#3 Full forward chassis

Full forward chassis in which the engine is fitted outside the driver cabin or seats like in
cars and old Tata trucks. In this arrangement, the driver's seat is far enough from the
front wheel.

#4 Semi forward

In this types of chassis, half portion of the engine is in the driver cabin and the other
remaining half is outside of the cabin Bedford pack up. It gives better visibility of the
road to the driver.

#5 Bus chassis

In this type of chassis, the whole engine is fitted in the driver cabin. As shown in the
figure. It provides an increased floor space in the vehicle. The driver's seat is above the
front wheel and he can see the full front road right from the front wheels.

#6 Engine in front

In most vehicles, the engine is fitted in the front portion of the chassis. The drive is
given to the front wheels. The engine may also be added at the back portion of the
chassis. This arrangement does not require a long propeller shaft. Gearbox and
differential arc combined in one unit.

#7 Engine at the center

The engine may also be fitted at the center of the chassis. This type of arrangement
gives full space of chassis floor for use. In the Royal tiger world master bus, the engines
are fitted at the center of the chassis.

What is Frame?
The frame is an important part of the chassis. All the remaining components of the
chassis are mounted on it. It is a rigid structure that forms a skeleton to hold all the
components together.

The engine is fixed in the front end of the frame and attaches to the clutch and
transmission unit to form the power assembly. At the rear end of the frame, the rear
axle is attached through the rear spring. On the steering system, some parts are bolted
to the frame and some on the body. The petrol tank is fixed to the rear of the frame.

TheEngineersPost.com Page 4
 Types of Chassis

Working of the Frame

1. To carry the weight of a vehicle and passengers.
2. It withstand the engine and transmission torque and thrust stresses, as well as
accelerating and braking torques.
3. To withstand the centrifugal force while cornering.
4. To withstand the bending stresses and twisting due to the. As and fall of the
front and rear axles.

Types of Chassis Frames

There are three types of frames:

1. Conventional Frame
2. Semi-Integral Frame
3. Integral or unit frame

#1 Conventional Frame

Conventional-frame is also known as non-load carrying frame. In this type of frame, the
loads on the vehicle are transferred to the suspension by the frame, which is the main
skeleton of the vehicle. The frame supports the engine, power train, and vehicle body. It
is supported on the wheel axles by means of springs.

The bodywork is done by flexible material such as a wood and is completely different
from frame deflection with the help of rubber mounting. This type of construction is
widely used in trucks. The frame sections are normally channel, tubular, or box type.
The channel frame section is good in bending, a tubular section in torsion, and a box in
bending and torsion.

TheEngineersPost.com Page 5
 Types of Chassis

#2 Semi-integral frame

In the semi-integral frame, the rubber body mounts are replaced by relatively stiff
mounts so that a part of the frame load is transferred to the body structure also. This
type of frame is quite popular for small. European cars and American cars. is, however,
heavy.

#3 Integral or unit frame

In the integral or unit frame and body type construction, there is no frame and all
assembly units are attached to the body. The body and frame is a single unit which is
welded together and all the function of the frame are carried out on it.

The construction is such that the body sheets relieve the metal framework of part of the
stresses. This saves some weight over the conventional separate frame and body
construction.

How Frame is Made?

The frames are made by following three different steel sections:

1. Channel section.
2. Box section.
3. Tubular section.

Channel section is employed in long members and box section is employed cross
members. Tubular section is used nowadays in three-wheeler, scooters and matadores,
pick-up frames. The frames should be strong enough to bear the load, sudden brakes,
and accidents.

What is Sub-Frames?
The various components of a motor vehicle are bolted directly either on mainframe
members or cross member of the frame. But sometimes, the engine and gearbox are
carried on a sub-frame of simple construction.

The sub-frame is supported by the mainframe usually at three points. The object of this
arrangement is to isolate these components from the effect of twisting and flexing of the
mainframe.

TheEngineersPost.com Page 6