511E

EPB
With Preload
° 45 ° 90°
45
30°
6- φ d1
8- φ d1

PC PC
D
D

A
Tｍ 22.5° A Tｍ 30 ° (Greasing hole)
(Greasing hole)
Hole type 1 Hole type 2
(Model EPB1605 to 3210) (Model EPB4005 to 6310)

Screw Lead Ball center- Thread No. of Basic load rating Rigidity
shaft outer to-center minor loaded
Model No. diameter diameter diameter circuits Ca★ C 0a K

d ℓ dp dC Rows x turns kN kN N/m

EPB 1605-6 16 5 16.75 13.1 3×1 9.3 13.1 317
EPB 2005-6 20 5 20.75 17.1 3×1 10.6 17.3 310
EPB 2505-6 25 5 25.75 22.1 3×1 12.1 22.6 490
EPB 2510-4 25 10 26 21.6 2×1 11.3 18 330
EPB 3205-6 32 5 32.75 29.2 3×1 13.9 30.2 620
EPB 3205-8 32 5 32.75 29.2 4×1 17.8 40.3 810
EPB 3210-6 32 10 33.75 26.4 3×1 32.1 52.2 600
EPB 4005-6 40 5 40.75 37.1 3×1 15.4 38.8 298
EPB 4010-6 40 10 41.75 34.7 3×1 37.3 69.3 750
EPB 4010-8 40 10 41.75 34.7 4×1 47.6 92.4 1000
EPB 5010-8 50 10 51.75 44.4 4×1 54.3 120.5 1230
EPB 6310-8 63 10 64.75 57.7 4×1 61.9 160.7 1550
Note) ★ Basic Dynamic Load Rating(Ca) of the accuracy C7 and Ct7 is 0.9Ca.

Model number coding

EP B 20 05 -6 QZ RR G0 +650L C3
Shaft diameter Number of turns Clearance symbol Accuracy symbol
Lead Ball screw shaft length (mm)
Seal symbol (RR : Labyrinth seal, WW : Wiper ring.)
With QZ Lubricator (no symbol without QZ Lubricator)
Flange shape: A: round; B: double chamfered; C: single chamfered
Nut type: offset preloaded type

Download data by searching for the corresponding

A15-102 model number on the Technical Support site. https://tech.thk.com
 511E

DIN Standard compliant Ball Screw (DIN69051)

L1

H B1

φ Dg6

φ D -0.2
0
φ D1 φ D -0.2
0
φ dC φ d

B2

Unit: mm
Nut dimensions
Outer Flange Overall Greasing
diameter diameter length hole
D D1 L1 H B1 B2 Hole type PCD d1 Tm A

Ball Screw
28 48 65 10 50 12 1 38 5.5 20 M6×1
36 58 66 10 51 12 1 47 6.6 22 M6×1
40 62 66 10 51 12 1 51 6.6 24 M6×1
40 62 85 10 70 18 1 51 6.6 24 M6×1
50 80 67 12 50 12 1 65 9 31 M6×1
50 80 78 12 61 12 1 65 9 31 M6×1
50 80 112 12 95 18 1 65 9 31 M6×1
63 93 70 14 51 12 2 78 9 35 M8×1
63 93 114 14 95 18 2 78 9 35 M8×1
63 93 138 14 119 18 2 78 9 35 M8×1
75 110 140 16 119 18 2 93 11 42.5 M8×1
90 125 142 18 119 18 2 108 11 47.5 M8×1

Note) The rigidity values in the table represent spring constants each obtained from the
load and the elastic deformation when providing a preload 8% of the basic dynam- 1
ic load rating (Ca) and applying an axial load three times greater than the preload. Fa0 3

These values do not include the rigidity of the components related to mounting the
nut. Therefore, it is normally appropriate to regard roughly 80% of the value in the
K N ＝K
（   ）0.08Ca

table as the actual value. K: Rigidity value in the

If the applied preload (Fa0) is not 0.08 Ca, the rigidity value (KN) is obtained from dimensional table.
the following equation.

Options⇒A15-335 A15-103