Microcontroller to Sensor

Interfacing Techniques
Document Revision: 1.01
Date: 3rd February, 2006

16301 Blue Ridge Road, Missouri City, Texas 77489

Telephone: 1-713-283-9970 Fax: 1-281-416-2806
E-mail: [email protected]
Web: www.bipom.com

This document is available for download from www.bipom.com

© 2009 by BiPOM Electronics. All rights reserved.

Microcontroller to Sensor Interfacing Techniques. No part of this work may be reproduced in any manner without
written permission of BiPOM Electronics.

All trademarked names in this manual are the property of respective owners.
Overview

Micro-controllers are useful to the extent that they communicate with other devices, such as sensors,
motors, switches, keypads, displays, memory and even other micro-controllers.

Many interface methods have been developed over the years to solve the complex problem of balancing
circuit design criteria such as features, cost, size, weight, power consumption, reliability, availability,
manufacturability.

Many microcontroller designs typically mix multiple interfacing methods. In a very simplistic form, a micro-
controller system can be viewed as a system that reads from (monitors) inputs, performs processing and
writes to ( controls ) outputs.

Input Devices Microcontroller Output Devices

Microcontroller Interfaces

Digital Analog

On/Off Parallel Serial Voltage Current

Asynchronous Synchronous
1-wire 2-wire (I2C)
RS232/RS485 4-wire (SPI, Microwire)
Ethernet

Page 2
 Analog Inputs/Outputs

Voltage-based control and monitoring.

Disadvantages
• High cost for higher resolutions
Advantages
• Not all microcontrollers have analog
• Simple interface inputs/outputs built-in
• Low cost for low-resolutions • Complicates the circuit design when external ADC
• High speed or DAC are needed.
• Low programming overhead • Short distance, few feet maximum.

Voltage type: Typical ranges

• 0 to 2.5V
• 0 to 4V
• 0 to 5V
• +/- 2.5V
• +/- 4V
• +/- 5V

Current type: Typical ranges

• 0-20mA
• 4-20mA

Analog Interface
Vcc

Amplifier
Potentiometer

LM35 Vcc Analog/ Digital/

8051
Temperature Digital Analog
Sensor Microcontroller
Vcc Converter Converter
(AT89C51ED2)
(ADC) (DAC)

4-20mA
Strain-gage
Output

Page 3
Sensor Types

• Temperature
• Humidity
• Light
• Acceleration
• Force
• Frequency
• Flow
• Pressure
• Torque
• Proximity
• Displacement

Temperature Sensors

• RTD
• Thermistor
• Thermocouple
• Semiconductor Temperature Sensors

Criteria Thermocouple RTD Thermistor Semiconductor

Temperature Range Wide narrow
Very wide narrow
-400°F -100°F
-450°F +4200°F -60°F to 250°F
+1200°F +500°F
Interchangeability Good Excellent Poor to fair Good
Long-term Stability Poor to fair Good Poor Good
Accuracy Medium High Medium High
Repeatability Fair Excellent Fair to good Good
Sensitivity (output) Low Medium Very high High
Medium to
Response Medium to fast Medium Medium to fast
fast
Linearity Fair Good Poor Good
Self Heating No Very low to low High High
Point (end)
Excellent Fair Good Good
Sensitive
Lead Effect High Medium Low Low
Medium to Small to Small to
Size/Packaging Small to large
small medium medium

Page 4
RTD’s
Also called Platinum RTD because it is typically made of platinum. A change in temperature causes a
change in resistance of platinum. This change can be measured with an ohmmeter.

Within a limited range, the resistance of metals increases in proportion to the temperature as defined by
the formula:

where:

= resistance at temperature

= resistance at a standard temperature

α = temperature coefficient of resistance ( )

In theory, any metal could be used to measure temperature. The metal selected should have a high
melting point and an ability to withstand the effects of corrosion. Platinum has therefore become the metal
of choice for RTD's. Its desirable characteristics include chemical stability, availability in a pure form, and
electrical properties that are highly reproducible.

Typical readings for platinum are 100 ohms at 0 Celsius and 139 ohms at 100.

Wire-wound type Thin film type

Page 5
 I FE R V0NIA = R T RD I FE R

AIN0

Platinum RTD
(R TRD )

Ground

RTD’s require a constant current source, such as 1mA. Such a low current keeps
the self heating to a minimum.

5V

- A na log/D ig ital
C o nverte r M icrocontro ller
(A D C )

R TD

VREF

Page 6
Thermistors

Thermistors are thermally sensitive resistors and have, according to type, a negative (NTC), or positive
(PTC) resistance/temperature coefficient.

Manufactured from the oxides of the transition metals - manganese, cobalt, copper and nickel, NTC
thermistors are temperature dependant semiconductor resistors. Operating over a range of -200°C to +
1000°C, they are supplied in glass bead, disc, chips and probe formats.

Thermistors are typically very low cost devices ( under $1 ).

Page 7
 V FE R

Thermistor R
(R th )
V0NIA = VFER
R + R th
AIN0

Known
resistor
(R)
Ground

Page 8
Thermocouples

Page 9
Semiconductor Temperature Sensors

Analog

Voltage Output

Typically three-pin devices: Power, ground and output.

LM34: Fahrenheit sensor ( 10 millivolts/Fahrenheit )

LM35: Celsius sensor ( 10 millivolts/Celsius )
LM335: Kelvin sensor ( 10 millivolts/Kelvin )

Page 10
Analog Digital Conversion
• Voltage to Frequency
• Flash ADC
• Successive Approximation
• Dual-Slope Integration
• Delta-Sigma

Successive approximation ADC

Successive Approximation ADC’s are popular for use with microcontrollers due to low-cost
and ease of interfacing. A successive approximation ADC consists of:
• Successive Approximation Register
• Result Register
• DAC
• Comparator
Successive-approximation register counts by trying all values of bits starting with the most-
significant bit and finishing at the least-significant bit. Throughout the count process, the
register monitors the comparator's output to see if the binary count is less than or greater
than the analog signal input, adjusting the bit values accordingly. This way, the DAC output
eventually converges on the analog input signal and the result is presented in the Result
register.

Page 11
Voltage

DAC
Output
Input
Voltage

Time

ADC can be external to the microcontroller or built-in:

Analog/
Analog/Digital
AT89C51ED2 Digital PIC16F818
Converter
Microcontroller Converter Microcontroller
(ADC)
(ADC)

Page 12
Noise considerations
Many sensors, such as thermocouples, generate a relatively small voltage so noise is always an issue.
The most common source of noise is the utility power lines (50 Hz or 60 Hz).

Typically, the bandwidth for temperature sensors is much lower than 50 or 60 Hz so a simple low-pass
filter will work well in many cases.

Other measures to keep noise away:

• Keep the sensor wires short.

• Use shielded sensor cables with twisted pair wires.

• Use a dedicated precision voltage reference, not the microcontroller supply.

• Use 4-20mA loop or even better, a digital signal for long cable runs.

• Provide low impedance paths to ground at the ADC inputs if possible.

• Average readings in software.

• Analog ground and digital ground should connect at the ADC.

• Analog ground should not carry large currents.

• Ground planes should not carry any currents.

Analog/Digital
Sensor Converter Microcontroller
(ADC)

Analog Ground Digital Ground

Page 13