Scribd
Upload
191 views

Thin-Walled Pressure Vessels: Tangential Stress

The document discusses thin-walled pressure vessels and the stresses they experience. It defines the formulas for calculating tangential (circumferential) stress and longitudinal stress in cylindrical vessels based on internal pressure, wall thickness, and diameter. It also provides the formula for stress in spherical shells. Several sample problems are then shown calculating stresses and required wall thicknesses for different vessel geometries under given pressures.

Uploaded by

ruth lopez
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
191 views

Thin-Walled Pressure Vessels: Tangential Stress

The document discusses thin-walled pressure vessels and the stresses they experience. It defines the formulas for calculating tangential (circumferential) stress and longitudinal stress in cylindrical vessels based on internal pressure, wall thickness, and diameter. It also provides the formula for stress in spherical shells. Several sample problems are then shown calculating stresses and required wall thicknesses for different vessel geometries under given pressures.

Uploaded by

ruth lopez
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Thin-Walled Pressure Vessels

A tank or pipe carrying a fluid or gas under a pressure is subjected to tensile forces,

which resist bursting, developed across longitudinal and transverse sections.

TANGENTIAL STRESS

(Circumferential Stress)

Consider the tank shown being subjected to an internal pressure p. The length of the

tank is L and the wall thickness is t. Isolating the right half of the tank:

If there exist an external pressure po and an internal pressure pi, the formula may be

expressed as:

LONGITUDINAL STRESS, σL

Consider the free body diagram in the transverse section of the tank:

The total force acting at the rear of the tank F must equal to the total longitudinal stress

on the wall PT = σL Awall. Since t is so small compared to D, the area of the wall is close

to πDt
If there exist an external pressure po and an internal pressure pi, the formula may be

expressed as:

It can be observed that the tangential stress is twice that of the longitudinal stress.

σt = 2 σL

SPHERICAL SHELL

If a spherical tank of diameter D and thickness t contains gas under a

pressure of p, the stress at the wall can be expressed as:


SOLVED PROBLEMS IN THIN-WALLED PREASSURE VESSELS

Problem 133

A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm,

is subjected to an internal pressure of 4.5 MN/m2. (a) Calculate the tangential and

longitudinal stresses in the steel. (b) To what value may the internal pressure be

increased if the stress in the steel is limited to 120 MN/m2? (c) If the internal pressure

were increased until the vessel burst, sketch the type of fracture that would occur.

Solution 133
Problem 134

The wall thickness of a 4-ft-diameter spherical tank is 5/16 in. Calculate the allowable

internal pressure if the stress is limited to 8000 psi.

Solution 134

Problem 135

Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a

pressure of 1400 psi. The diameter of the vessel is 2 ft, and the stress is limited to 12

ksi.

Solution 135
Problem 5

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20

mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine

the maximum internal pressure that can be applied if the longitudinal stress is limited

to 140 MPa, and the circumferential stress is limited to 60 MPa. Solution 136
Problem 6

A water tank, 22 ft in diameter, is made from steel plates that are ½ in. thick. Find the

maximum height to which the tank may be filled if the circumferential stress is limited

to 6000 psi. The specific weight of water is 62.4 lb/ft3.

Solution 137
Problem 7

The strength of longitudinal joint in Fig. 1-17 is 33 kips/ft, whereas for the girth is 16

kips/ft. Calculate the maximum diameter of the cylinder tank if the internal pressure is

150 psi.

Solution 138
Problem 8

Find the limiting peripheral velocity of a rotating steel ring if the allowable stress is 20

ksi and steel weighs 490 lb/ft3. At what revolutions per minute (rpm) will the stress

reach 30 ksi if the mean radius is 10 in.?

Solution 139
Problem 9

At what angular velocity will the stress of the rotating steel ring equal 150 MPa if its

mean radius is 220 mm? The density of steel 7.85 Mg/m3.

Solution 140

Problem 141

The tank shown in Fig. P-141 is fabricated from 1/8-in steel plate. Calculate the

maximum longitudinal and circumferential stress caused by an internal pressure of 125

psi.

Solution 141
Problem 10

Problem 142

A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10

mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap

the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable

stress in the bolts is 80 MPa, of which 55 MPa is the initial stress? What circumferential stress is

developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if

the steam pressure should cause the stress in the bolts to be twice the value of the initial stress?

Solution 142

You might also like